/**************************************************************************** * Driver for Solarflare Solarstorm network controllers and boards * Copyright 2007-2008 Solarflare Communications Inc. * * This program is free software; you can redistribute it and/or modify it * under the terms of the GNU General Public License version 2 as published * by the Free Software Foundation, incorporated herein by reference. */ #include #include "net_driver.h" #include "phy.h" #include "efx.h" #include "falcon.h" #include "regs.h" #include "falcon_io.h" #include "workarounds.h" /* Macros for unpacking the board revision */ /* The revision info is in host byte order. */ #define FALCON_BOARD_TYPE(_rev) (_rev >> 8) #define FALCON_BOARD_MAJOR(_rev) ((_rev >> 4) & 0xf) #define FALCON_BOARD_MINOR(_rev) (_rev & 0xf) /* Board types */ #define FALCON_BOARD_SFE4001 0x01 #define FALCON_BOARD_SFE4002 0x02 #define FALCON_BOARD_SFN4111T 0x51 #define FALCON_BOARD_SFN4112F 0x52 /* Blink support. If the PHY has no auto-blink mode so we hang it off a timer */ #define BLINK_INTERVAL (HZ/2) static void blink_led_timer(unsigned long context) { struct efx_nic *efx = (struct efx_nic *)context; struct efx_blinker *bl = &efx->board_info.blinker; efx->board_info.set_id_led(efx, bl->state); bl->state = !bl->state; if (bl->resubmit) mod_timer(&bl->timer, jiffies + BLINK_INTERVAL); } static void board_blink(struct efx_nic *efx, bool blink) { struct efx_blinker *blinker = &efx->board_info.blinker; /* The rtnl mutex serialises all ethtool ioctls, so * nothing special needs doing here. */ if (blink) { blinker->resubmit = true; blinker->state = false; setup_timer(&blinker->timer, blink_led_timer, (unsigned long)efx); mod_timer(&blinker->timer, jiffies + BLINK_INTERVAL); } else { blinker->resubmit = false; if (blinker->timer.function) del_timer_sync(&blinker->timer); efx->board_info.init_leds(efx); } } /***************************************************************************** * Support for LM87 sensor chip used on several boards */ #define LM87_REG_ALARMS1 0x41 #define LM87_REG_ALARMS2 0x42 #define LM87_IN_LIMITS(nr, _min, _max) \ 0x2B + (nr) * 2, _max, 0x2C + (nr) * 2, _min #define LM87_AIN_LIMITS(nr, _min, _max) \ 0x3B + (nr), _max, 0x1A + (nr), _min #define LM87_TEMP_INT_LIMITS(_min, _max) \ 0x39, _max, 0x3A, _min #define LM87_TEMP_EXT1_LIMITS(_min, _max) \ 0x37, _max, 0x38, _min #define LM87_ALARM_TEMP_INT 0x10 #define LM87_ALARM_TEMP_EXT1 0x20 #if defined(CONFIG_SENSORS_LM87) || defined(CONFIG_SENSORS_LM87_MODULE) static int efx_init_lm87(struct efx_nic *efx, struct i2c_board_info *info, const u8 *reg_values) { struct i2c_client *client = i2c_new_device(&efx->i2c_adap, info); int rc; if (!client) return -EIO; while (*reg_values) { u8 reg = *reg_values++; u8 value = *reg_values++; rc = i2c_smbus_write_byte_data(client, reg, value); if (rc) goto err; } efx->board_info.hwmon_client = client; return 0; err: i2c_unregister_device(client); return rc; } static void efx_fini_lm87(struct efx_nic *efx) { i2c_unregister_device(efx->board_info.hwmon_client); } static int efx_check_lm87(struct efx_nic *efx, unsigned mask) { struct i2c_client *client = efx->board_info.hwmon_client; s32 alarms1, alarms2; /* If link is up then do not monitor temperature */ if (EFX_WORKAROUND_7884(efx) && efx->link_up) return 0; alarms1 = i2c_smbus_read_byte_data(client, LM87_REG_ALARMS1); alarms2 = i2c_smbus_read_byte_data(client, LM87_REG_ALARMS2); if (alarms1 < 0) return alarms1; if (alarms2 < 0) return alarms2; alarms1 &= mask; alarms2 &= mask >> 8; if (alarms1 || alarms2) { EFX_ERR(efx, "LM87 detected a hardware failure (status %02x:%02x)" "%s%s\n", alarms1, alarms2, (alarms1 & LM87_ALARM_TEMP_INT) ? " INTERNAL" : "", (alarms1 & LM87_ALARM_TEMP_EXT1) ? " EXTERNAL" : ""); return -ERANGE; } return 0; } #else /* !CONFIG_SENSORS_LM87 */ static inline int efx_init_lm87(struct efx_nic *efx, struct i2c_board_info *info, const u8 *reg_values) { return 0; } static inline void efx_fini_lm87(struct efx_nic *efx) { } static inline int efx_check_lm87(struct efx_nic *efx, unsigned mask) { return 0; } #endif /* CONFIG_SENSORS_LM87 */ /***************************************************************************** * Support for the SFE4001 and SFN4111T NICs. * * The SFE4001 does not power-up fully at reset due to its high power * consumption. We control its power via a PCA9539 I/O expander. * Both boards have a MAX6647 temperature monitor which we expose to * the lm90 driver. * * This also provides minimal support for reflashing the PHY, which is * initiated by resetting it with the FLASH_CFG_1 pin pulled down. * On SFE4001 rev A2 and later this is connected to the 3V3X output of * the IO-expander; on the SFN4111T it is connected to Falcon's GPIO3. * We represent reflash mode as PHY_MODE_SPECIAL and make it mutually * exclusive with the network device being open. */ /************************************************************************** * Support for I2C IO Expander device on SFE40001 */ #define PCA9539 0x74 #define P0_IN 0x00 #define P0_OUT 0x02 #define P0_INVERT 0x04 #define P0_CONFIG 0x06 #define P0_EN_1V0X_LBN 0 #define P0_EN_1V0X_WIDTH 1 #define P0_EN_1V2_LBN 1 #define P0_EN_1V2_WIDTH 1 #define P0_EN_2V5_LBN 2 #define P0_EN_2V5_WIDTH 1 #define P0_EN_3V3X_LBN 3 #define P0_EN_3V3X_WIDTH 1 #define P0_EN_5V_LBN 4 #define P0_EN_5V_WIDTH 1 #define P0_SHORTEN_JTAG_LBN 5 #define P0_SHORTEN_JTAG_WIDTH 1 #define P0_X_TRST_LBN 6 #define P0_X_TRST_WIDTH 1 #define P0_DSP_RESET_LBN 7 #define P0_DSP_RESET_WIDTH 1 #define P1_IN 0x01 #define P1_OUT 0x03 #define P1_INVERT 0x05 #define P1_CONFIG 0x07 #define P1_AFE_PWD_LBN 0 #define P1_AFE_PWD_WIDTH 1 #define P1_DSP_PWD25_LBN 1 #define P1_DSP_PWD25_WIDTH 1 #define P1_RESERVED_LBN 2 #define P1_RESERVED_WIDTH 2 #define P1_SPARE_LBN 4 #define P1_SPARE_WIDTH 4 /* Temperature Sensor */ #define MAX664X_REG_RSL 0x02 #define MAX664X_REG_WLHO 0x0B static void sfe4001_poweroff(struct efx_nic *efx) { struct i2c_client *ioexp_client = efx->board_info.ioexp_client; struct i2c_client *hwmon_client = efx->board_info.hwmon_client; /* Turn off all power rails and disable outputs */ i2c_smbus_write_byte_data(ioexp_client, P0_OUT, 0xff); i2c_smbus_write_byte_data(ioexp_client, P1_CONFIG, 0xff); i2c_smbus_write_byte_data(ioexp_client, P0_CONFIG, 0xff); /* Clear any over-temperature alert */ i2c_smbus_read_byte_data(hwmon_client, MAX664X_REG_RSL); } static int sfe4001_poweron(struct efx_nic *efx) { struct i2c_client *hwmon_client = efx->board_info.hwmon_client; struct i2c_client *ioexp_client = efx->board_info.ioexp_client; unsigned int i, j; int rc; u8 out; /* Clear any previous over-temperature alert */ rc = i2c_smbus_read_byte_data(hwmon_client, MAX664X_REG_RSL); if (rc < 0) return rc; /* Enable port 0 and port 1 outputs on IO expander */ rc = i2c_smbus_write_byte_data(ioexp_client, P0_CONFIG, 0x00); if (rc) return rc; rc = i2c_smbus_write_byte_data(ioexp_client, P1_CONFIG, 0xff & ~(1 << P1_SPARE_LBN)); if (rc) goto fail_on; /* If PHY power is on, turn it all off and wait 1 second to * ensure a full reset. */ rc = i2c_smbus_read_byte_data(ioexp_client, P0_OUT); if (rc < 0) goto fail_on; out = 0xff & ~((0 << P0_EN_1V2_LBN) | (0 << P0_EN_2V5_LBN) | (0 << P0_EN_3V3X_LBN) | (0 << P0_EN_5V_LBN) | (0 << P0_EN_1V0X_LBN)); if (rc != out) { EFX_INFO(efx, "power-cycling PHY\n"); rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out); if (rc) goto fail_on; schedule_timeout_uninterruptible(HZ); } for (i = 0; i < 20; ++i) { /* Turn on 1.2V, 2.5V, 3.3V and 5V power rails */ out = 0xff & ~((1 << P0_EN_1V2_LBN) | (1 << P0_EN_2V5_LBN) | (1 << P0_EN_3V3X_LBN) | (1 << P0_EN_5V_LBN) | (1 << P0_X_TRST_LBN)); if (efx->phy_mode & PHY_MODE_SPECIAL) out |= 1 << P0_EN_3V3X_LBN; rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out); if (rc) goto fail_on; msleep(10); /* Turn on 1V power rail */ out &= ~(1 << P0_EN_1V0X_LBN); rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out); if (rc) goto fail_on; EFX_INFO(efx, "waiting for DSP boot (attempt %d)...\n", i); /* In flash config mode, DSP does not turn on AFE, so * just wait 1 second. */ if (efx->phy_mode & PHY_MODE_SPECIAL) { schedule_timeout_uninterruptible(HZ); return 0; } for (j = 0; j < 10; ++j) { msleep(100); /* Check DSP has asserted AFE power line */ rc = i2c_smbus_read_byte_data(ioexp_client, P1_IN); if (rc < 0) goto fail_on; if (rc & (1 << P1_AFE_PWD_LBN)) return 0; } } EFX_INFO(efx, "timed out waiting for DSP boot\n"); rc = -ETIMEDOUT; fail_on: sfe4001_poweroff(efx); return rc; } static int sfn4111t_reset(struct efx_nic *efx) { efx_oword_t reg; /* GPIO 3 and the GPIO register are shared with I2C, so block that */ mutex_lock(&efx->i2c_adap.bus_lock); /* Pull RST_N (GPIO 2) low then let it up again, setting the * FLASH_CFG_1 strap (GPIO 3) appropriately. Only change the * output enables; the output levels should always be 0 (low) * and we rely on external pull-ups. */ falcon_read(efx, ®, FR_AB_GPIO_CTL); EFX_SET_OWORD_FIELD(reg, FRF_AB_GPIO2_OEN, true); falcon_write(efx, ®, FR_AB_GPIO_CTL); msleep(1000); EFX_SET_OWORD_FIELD(reg, FRF_AB_GPIO2_OEN, false); EFX_SET_OWORD_FIELD(reg, FRF_AB_GPIO3_OEN, !!(efx->phy_mode & PHY_MODE_SPECIAL)); falcon_write(efx, ®, FR_AB_GPIO_CTL); msleep(1); mutex_unlock(&efx->i2c_adap.bus_lock); ssleep(1); return 0; } static ssize_t show_phy_flash_cfg(struct device *dev, struct device_attribute *attr, char *buf) { struct efx_nic *efx = pci_get_drvdata(to_pci_dev(dev)); return sprintf(buf, "%d\n", !!(efx->phy_mode & PHY_MODE_SPECIAL)); } static ssize_t set_phy_flash_cfg(struct device *dev, struct device_attribute *attr, const char *buf, size_t count) { struct efx_nic *efx = pci_get_drvdata(to_pci_dev(dev)); enum efx_phy_mode old_mode, new_mode; int err; rtnl_lock(); old_mode = efx->phy_mode; if (count == 0 || *buf == '0') new_mode = old_mode & ~PHY_MODE_SPECIAL; else new_mode = PHY_MODE_SPECIAL; if (old_mode == new_mode) { err = 0; } else if (efx->state != STATE_RUNNING || netif_running(efx->net_dev)) { err = -EBUSY; } else { /* Reset the PHY, reconfigure the MAC and enable/disable * MAC stats accordingly. */ efx->phy_mode = new_mode; if (new_mode & PHY_MODE_SPECIAL) efx_stats_disable(efx); if (efx->board_info.type == FALCON_BOARD_SFE4001) err = sfe4001_poweron(efx); else err = sfn4111t_reset(efx); efx_reconfigure_port(efx); if (!(new_mode & PHY_MODE_SPECIAL)) efx_stats_enable(efx); } rtnl_unlock(); return err ? err : count; } static DEVICE_ATTR(phy_flash_cfg, 0644, show_phy_flash_cfg, set_phy_flash_cfg); static void sfe4001_fini(struct efx_nic *efx) { EFX_INFO(efx, "%s\n", __func__); device_remove_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg); sfe4001_poweroff(efx); i2c_unregister_device(efx->board_info.ioexp_client); i2c_unregister_device(efx->board_info.hwmon_client); } static int sfe4001_check_hw(struct efx_nic *efx) { s32 status; /* If XAUI link is up then do not monitor */ if (EFX_WORKAROUND_7884(efx) && efx->mac_up) return 0; /* Check the powered status of the PHY. Lack of power implies that * the MAX6647 has shut down power to it, probably due to a temp. * alarm. Reading the power status rather than the MAX6647 status * directly because the later is read-to-clear and would thus * start to power up the PHY again when polled, causing us to blip * the power undesirably. * We know we can read from the IO expander because we did * it during power-on. Assume failure now is bad news. */ status = i2c_smbus_read_byte_data(efx->board_info.ioexp_client, P1_IN); if (status >= 0 && (status & ((1 << P1_AFE_PWD_LBN) | (1 << P1_DSP_PWD25_LBN))) != 0) return 0; /* Use board power control, not PHY power control */ sfe4001_poweroff(efx); efx->phy_mode = PHY_MODE_OFF; return (status < 0) ? -EIO : -ERANGE; } static struct i2c_board_info sfe4001_hwmon_info = { I2C_BOARD_INFO("max6647", 0x4e), }; /* This board uses an I2C expander to provider power to the PHY, which needs to * be turned on before the PHY can be used. * Context: Process context, rtnl lock held */ static int sfe4001_init(struct efx_nic *efx) { int rc; #if defined(CONFIG_SENSORS_LM90) || defined(CONFIG_SENSORS_LM90_MODULE) efx->board_info.hwmon_client = i2c_new_device(&efx->i2c_adap, &sfe4001_hwmon_info); #else efx->board_info.hwmon_client = i2c_new_dummy(&efx->i2c_adap, sfe4001_hwmon_info.addr); #endif if (!efx->board_info.hwmon_client) return -EIO; /* Raise board/PHY high limit from 85 to 90 degrees Celsius */ rc = i2c_smbus_write_byte_data(efx->board_info.hwmon_client, MAX664X_REG_WLHO, 90); if (rc) goto fail_hwmon; efx->board_info.ioexp_client = i2c_new_dummy(&efx->i2c_adap, PCA9539); if (!efx->board_info.ioexp_client) { rc = -EIO; goto fail_hwmon; } /* 10Xpress has fixed-function LED pins, so there is no board-specific * blink code. */ efx->board_info.blink = tenxpress_phy_blink; efx->board_info.monitor = sfe4001_check_hw; efx->board_info.fini = sfe4001_fini; if (efx->phy_mode & PHY_MODE_SPECIAL) { /* PHY won't generate a 156.25 MHz clock and MAC stats fetch * will fail. */ efx_stats_disable(efx); } rc = sfe4001_poweron(efx); if (rc) goto fail_ioexp; rc = device_create_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg); if (rc) goto fail_on; EFX_INFO(efx, "PHY is powered on\n"); return 0; fail_on: sfe4001_poweroff(efx); fail_ioexp: i2c_unregister_device(efx->board_info.ioexp_client); fail_hwmon: i2c_unregister_device(efx->board_info.hwmon_client); return rc; } static int sfn4111t_check_hw(struct efx_nic *efx) { s32 status; /* If XAUI link is up then do not monitor */ if (EFX_WORKAROUND_7884(efx) && efx->mac_up) return 0; /* Test LHIGH, RHIGH, FAULT, EOT and IOT alarms */ status = i2c_smbus_read_byte_data(efx->board_info.hwmon_client, MAX664X_REG_RSL); if (status < 0) return -EIO; if (status & 0x57) return -ERANGE; return 0; } static void sfn4111t_fini(struct efx_nic *efx) { EFX_INFO(efx, "%s\n", __func__); device_remove_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg); i2c_unregister_device(efx->board_info.hwmon_client); } static struct i2c_board_info sfn4111t_a0_hwmon_info = { I2C_BOARD_INFO("max6647", 0x4e), }; static struct i2c_board_info sfn4111t_r5_hwmon_info = { I2C_BOARD_INFO("max6646", 0x4d), }; static int sfn4111t_init(struct efx_nic *efx) { int i = 0; int rc; efx->board_info.hwmon_client = i2c_new_device(&efx->i2c_adap, (efx->board_info.minor < 5) ? &sfn4111t_a0_hwmon_info : &sfn4111t_r5_hwmon_info); if (!efx->board_info.hwmon_client) return -EIO; efx->board_info.blink = tenxpress_phy_blink; efx->board_info.monitor = sfn4111t_check_hw; efx->board_info.fini = sfn4111t_fini; rc = device_create_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg); if (rc) goto fail_hwmon; do { if (efx->phy_mode & PHY_MODE_SPECIAL) { /* PHY may not generate a 156.25 MHz clock and MAC * stats fetch will fail. */ efx_stats_disable(efx); sfn4111t_reset(efx); } rc = sft9001_wait_boot(efx); if (rc == 0) return 0; efx->phy_mode = PHY_MODE_SPECIAL; } while (rc == -EINVAL && ++i < 2); device_remove_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg); fail_hwmon: i2c_unregister_device(efx->board_info.hwmon_client); return rc; } /***************************************************************************** * Support for the SFE4002 * */ static u8 sfe4002_lm87_channel = 0x03; /* use AIN not FAN inputs */ static const u8 sfe4002_lm87_regs[] = { LM87_IN_LIMITS(0, 0x83, 0x91), /* 2.5V: 1.8V +/- 5% */ LM87_IN_LIMITS(1, 0x51, 0x5a), /* Vccp1: 1.2V +/- 5% */ LM87_IN_LIMITS(2, 0xb6, 0xca), /* 3.3V: 3.3V +/- 5% */ LM87_IN_LIMITS(3, 0xb0, 0xc9), /* 5V: 4.6-5.2V */ LM87_IN_LIMITS(4, 0xb0, 0xe0), /* 12V: 11-14V */ LM87_IN_LIMITS(5, 0x44, 0x4b), /* Vccp2: 1.0V +/- 5% */ LM87_AIN_LIMITS(0, 0xa0, 0xb2), /* AIN1: 1.66V +/- 5% */ LM87_AIN_LIMITS(1, 0x91, 0xa1), /* AIN2: 1.5V +/- 5% */ LM87_TEMP_INT_LIMITS(10, 60), /* board */ LM87_TEMP_EXT1_LIMITS(10, 70), /* Falcon */ 0 }; static struct i2c_board_info sfe4002_hwmon_info = { I2C_BOARD_INFO("lm87", 0x2e), .platform_data = &sfe4002_lm87_channel, }; /****************************************************************************/ /* LED allocations. Note that on rev A0 boards the schematic and the reality * differ: red and green are swapped. Below is the fixed (A1) layout (there * are only 3 A0 boards in existence, so no real reason to make this * conditional). */ #define SFE4002_FAULT_LED (2) /* Red */ #define SFE4002_RX_LED (0) /* Green */ #define SFE4002_TX_LED (1) /* Amber */ static void sfe4002_init_leds(struct efx_nic *efx) { /* Set the TX and RX LEDs to reflect status and activity, and the * fault LED off */ xfp_set_led(efx, SFE4002_TX_LED, QUAKE_LED_TXLINK | QUAKE_LED_LINK_ACTSTAT); xfp_set_led(efx, SFE4002_RX_LED, QUAKE_LED_RXLINK | QUAKE_LED_LINK_ACTSTAT); xfp_set_led(efx, SFE4002_FAULT_LED, QUAKE_LED_OFF); } static void sfe4002_set_id_led(struct efx_nic *efx, bool state) { xfp_set_led(efx, SFE4002_FAULT_LED, state ? QUAKE_LED_ON : QUAKE_LED_OFF); } static int sfe4002_check_hw(struct efx_nic *efx) { /* A0 board rev. 4002s report a temperature fault the whole time * (bad sensor) so we mask it out. */ unsigned alarm_mask = (efx->board_info.major == 0 && efx->board_info.minor == 0) ? ~LM87_ALARM_TEMP_EXT1 : ~0; return efx_check_lm87(efx, alarm_mask); } static int sfe4002_init(struct efx_nic *efx) { int rc = efx_init_lm87(efx, &sfe4002_hwmon_info, sfe4002_lm87_regs); if (rc) return rc; efx->board_info.monitor = sfe4002_check_hw; efx->board_info.init_leds = sfe4002_init_leds; efx->board_info.set_id_led = sfe4002_set_id_led; efx->board_info.blink = board_blink; efx->board_info.fini = efx_fini_lm87; return 0; } /***************************************************************************** * Support for the SFN4112F * */ static u8 sfn4112f_lm87_channel = 0x03; /* use AIN not FAN inputs */ static const u8 sfn4112f_lm87_regs[] = { LM87_IN_LIMITS(0, 0x83, 0x91), /* 2.5V: 1.8V +/- 5% */ LM87_IN_LIMITS(1, 0x51, 0x5a), /* Vccp1: 1.2V +/- 5% */ LM87_IN_LIMITS(2, 0xb6, 0xca), /* 3.3V: 3.3V +/- 5% */ LM87_IN_LIMITS(4, 0xb0, 0xe0), /* 12V: 11-14V */ LM87_IN_LIMITS(5, 0x44, 0x4b), /* Vccp2: 1.0V +/- 5% */ LM87_AIN_LIMITS(1, 0x91, 0xa1), /* AIN2: 1.5V +/- 5% */ LM87_TEMP_INT_LIMITS(10, 60), /* board */ LM87_TEMP_EXT1_LIMITS(10, 70), /* Falcon */ 0 }; static struct i2c_board_info sfn4112f_hwmon_info = { I2C_BOARD_INFO("lm87", 0x2e), .platform_data = &sfn4112f_lm87_channel, }; #define SFN4112F_ACT_LED 0 #define SFN4112F_LINK_LED 1 static void sfn4112f_init_leds(struct efx_nic *efx) { xfp_set_led(efx, SFN4112F_ACT_LED, QUAKE_LED_RXLINK | QUAKE_LED_LINK_ACT); xfp_set_led(efx, SFN4112F_LINK_LED, QUAKE_LED_RXLINK | QUAKE_LED_LINK_STAT); } static void sfn4112f_set_id_led(struct efx_nic *efx, bool state) { xfp_set_led(efx, SFN4112F_LINK_LED, state ? QUAKE_LED_ON : QUAKE_LED_OFF); } static int sfn4112f_check_hw(struct efx_nic *efx) { /* Mask out unused sensors */ return efx_check_lm87(efx, ~0x48); } static int sfn4112f_init(struct efx_nic *efx) { int rc = efx_init_lm87(efx, &sfn4112f_hwmon_info, sfn4112f_lm87_regs); if (rc) return rc; efx->board_info.monitor = sfn4112f_check_hw; efx->board_info.init_leds = sfn4112f_init_leds; efx->board_info.set_id_led = sfn4112f_set_id_led; efx->board_info.blink = board_blink; efx->board_info.fini = efx_fini_lm87; return 0; } /* This will get expanded as board-specific details get moved out of the * PHY drivers. */ struct falcon_board_data { u8 type; const char *ref_model; const char *gen_type; int (*init) (struct efx_nic *nic); }; static struct falcon_board_data board_data[] = { { FALCON_BOARD_SFE4001, "SFE4001", "10GBASE-T adapter", sfe4001_init }, { FALCON_BOARD_SFE4002, "SFE4002", "XFP adapter", sfe4002_init }, { FALCON_BOARD_SFN4111T, "SFN4111T", "100/1000/10GBASE-T adapter", sfn4111t_init }, { FALCON_BOARD_SFN4112F, "SFN4112F", "SFP+ adapter", sfn4112f_init }, }; void falcon_probe_board(struct efx_nic *efx, u16 revision_info) { struct falcon_board_data *data = NULL; int i; efx->board_info.type = FALCON_BOARD_TYPE(revision_info); efx->board_info.major = FALCON_BOARD_MAJOR(revision_info); efx->board_info.minor = FALCON_BOARD_MINOR(revision_info); for (i = 0; i < ARRAY_SIZE(board_data); i++) if (board_data[i].type == efx->board_info.type) data = &board_data[i]; if (data) { EFX_INFO(efx, "board is %s rev %c%d\n", (efx->pci_dev->subsystem_vendor == EFX_VENDID_SFC) ? data->ref_model : data->gen_type, 'A' + efx->board_info.major, efx->board_info.minor); efx->board_info.init = data->init; } else { EFX_ERR(efx, "unknown board type %d\n", efx->board_info.type); } }