Patch from Joel Sing to fix the default congestion control algorithm
for incoming connections. If a new congestion control handler is added
(via module), it should become the default for new
connections. Instead, the incoming connections use reno. The cause is
incorrect initialisation causes the tcp_init_congestion_control()
function to return after the initial if test fails.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Acked-by: Ian McDonald <imcdnzl@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup the printk's in fib_trie:
* Convert a couple of places in the dump code to BUG_ON
* Put log level's on each message
The version message really needed the message since it leaks out
on the pretty Fedora bootup.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Acked-by: Robert Olsson <Robert.Olsson@data.slu.se>,
Signed-off-by: David S. Miller <davem@davemloft.net>
The convention is that longer addresses will simply extend
the hardeware address byte arrays at the end of sockaddr_ll and
packet_mreq.
In making this change a small information leak was also closed.
The code only initializes the hardware address bytes that are
used, but all of struct sockaddr_ll was copied to userspace.
Now we just copy sockaddr_ll to the last byte of the hardware
address used.
For error checking larger structures than our internal
maximums continue to be allowed but an error is signaled if we can
not fit the hardware address into our internal structure.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In fbdev perspective, the frontporch is the lower/right margin and the
backporch is the upper/left margin.
Correct.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A recent change in nvidiafb caused nvidiafb_cursor to always return -ENXIO
instead of using the soft_cursor. This will happen if the parameter "hwcur"
is not set, which happens to be the default.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Arrange the modules, OBP, and vmalloc areas such that a range
verification can be done quite minimally.
Signed-off-by: David S. Miller <davem@davemloft.net>
ipoib_mcast_restart_task() is always called from within the
single-threaded IPoIB workqueue, so flushing the workqueue from within
the function can lead to a recursion overflow. But since we're
running in a single-threaded workqueue, we're already synchronized
against other items in the workqueue, so just get rid of the flush in
ipoib_mcast_restart_task().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
As per x86, we may deadlock while trying to get the mmap semaphore.
Implement the same fix, which allows (eg) recursive faults to cause
an oops instead of deadlocking.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
This code is not being exported, declare it static
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The `make buildcheck` is erroneously reporting that the .arch.info
list is referencing items in the .init section as it is not itself
postfixed with .init
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The `make buildcheck` is erroneously reporting that the .proc.info
list is referencing items in the .init section as it is not itself
postfixed with .init
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The `make buildcheck` is erroneously reporting that the earlyparam
list is referencing items in the .init section as it is not itself
postfixed with .init
Also, as per rmk's suggestion, rename the __early_param to
.early_param to bring it into line with everything else
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vincent Sanders
Shark platform fails to build with gcc 4 because of a bad lvalue assignement
Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The `make buildcheck` is erroneously reporting that the taglist
is referencing items in the .init section as it is not itself
postfixed with .init
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This showed that arch/sparc64/kernel/ptrace.c was not getting
the define properly, and thus the code protected by this ifdef
was never actually compiled before. So fix that too.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch comments the fact that although passing le64_to_cpup et
al. is within the intended use of the byteorder macros, using
get_unaligned is the recommended way to go.
Signed-off-by: Ed L. Cashin <ecashin@coraid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because we use byte loads/stores to cons up the value
in and out of registers, we can't expect the ASI endianness
setting to take care of this for us. So do it by hand.
This case is triggered by drivers/block/aoe/aoecmd.c in the
ataid_complete() function where it goes:
/* word 100: number lba48 sectors */
ssize = le64_to_cpup((__le64 *) &id[100<<1]);
This &id[100<<1] address is 4 byte, rather than 8 byte aligned,
thus triggering the unaligned exception.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix unchecked __get_user that could be tricked into generating a
memory read on an arbitrary address. The result of the read is not
returned directly but you may be able to divine some information about
it, or use the read to cause a crash on some architectures by reading
hardware state. CAN-2004-2492.
Fix from Al Viro, ack from Dave Miller.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The problem is that we're now calling tcp_fragment() in a context
where the packets might be marked as SACKED_ACKED or SACKED_RETRANS.
This was not possible before as you never retransmitted packets that
are so marked.
Because of this, we need to adjust sacked_out and retrans_out in
tcp_fragment(). This is exactly what the following patch does.
We also need to preserve the SACKED_ACKED/SACKED_RETRANS marking
if they exist.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following commit breaks cisco mode with my WAN drivers:
author David S. Miller <davem@davemloft.net>
Tue, 28 Jun 2005 22:25:31 +0000 (15:25 -0700)
commit 689be43945
"[NET]: Remove gratuitous use of skb->tail in network drivers."
The following patch fixes it - please apply (cisco_hard_header does
skb_push(4 bytes)).
Signed-off-by: David S. Miller <davem@davemloft.net>
Those exports are needed by the PPTP helper following in the next
couple of changes.
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both __ip_conntrack_expect_find and ip_conntrack_expect_find_get take
a reference to the expectation, the difference is that callers of
__ip_conntrack_expect_find must hold ip_conntrack_lock.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some IPv6 matches have very similar loops to find IPv6 extension header
and we can unify them. This patch introduces ipv6_find_hdr() to do it.
I just checked that it can find the target headers in the packet which has
dst,hbh,rt,frag,ah,esp headers.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new "version 3" PPTP conntrack/nat helper is finally ready for
mainline inclusion. Special thanks to lots of last-minute bugfixing
by Patric McHardy.
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* This patch is from Paul McKenney's RCU reviewing.
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Prints the route tnode and set the stats level deepth as before.
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to subtract off the header length from our payload
length when sending multi-packet SA messages.
Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
this patch adds some fc host attributes and removes its equivalents
from the zfcp_adapter structure and zfcp specific sysfs subtree.
Furthermore it removes superfluous calls to fc_remort_port_delete when
an adapter is set offline because rports will be removed by
fc_remove_host anyway.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
N_Port ID Virtualization (NPIV) allows a single FCP port to appear as
multiple, distinct ports providing separate port identification. NPIV
is supported by FC HBAs on System z9. zfcp was adapted to support this
new feature.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Debug features (DBFs) els_dbf, cmd_dbf and abt_dbf were removed and
san_dbf, hba_dbf and scsi_dbf were introduced. The erp_dbf did not
change.
The new traces improve debugging of problems with zfcp, scsi-stack,
multipath and hardware in the SAN. san_dbf traces things like ELS and
CT commands, hba_dbf saves HBA specific information of requests, and
scsi_dbf saves FCP and SCSI specific information of requests. Common
to all new DBFs is that they provide a so called structured view. This
significantly improves readability of the traces.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
o union zfcp_req_data removed
o increment unit refcount when processing FCP commands
(This fixes a theoretical race: When all scsi commands of a unit
are aborted and the scsi_device is removed then the unit could be
removed before all fsf_requests of that unit are completely processed.)
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
o always use locking when changing erp_action lists,
o avoid escalation to ERP_ACTION_REOPEN_PORT_FORCED if erp_action is
still in use for ERP_ACTION_REOPEN_PORT
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On Thursday, September 15, 2005 6:22 AM, Christoph Hellwig wrote:
> Looks good to me, except for the spurious scsi_print_command prototype
> in mptscsih.h.
The attached patch addresses that concern.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Summary of Changes:
* splitting mpt_interrupt per Christophs suggestion
about a month ago
* rename ScsiCfgData to SpiCfgData structure,
then move all the raid related info into
new structure called RaidCfgData. This is
done because SAS supports RAID, as well as SPI,
so the raid stuff should be seperate.
* incorrect timeout calculation for cntdn
inside WaitForDoorbellAck and WaitForDoortbellInt
* add support for interpreting SAS Log Info
* Increase Event Log Size from 0xA to 0x32
* Fix bug in mptsas/mptfc/mptspi - when controller
has Initiator Mode Disabled, and only running in
TargetMode, the mptctl would panic when loading.
The fix is to return 0, instead of -ENODEV, in
SCSI LLD respective probe routines
* Fix bug in mptlan.c - driver will panic if
there is host reset, due to dev being set to
zero in mpt_lan_ioc_reset
* Fix's for SPI - Echo Buffer
* Several fix's in mptscsih_io_done - FCP Response
info, RESIDUAL_MISMATCH, Data Underrun, etc.
* Cleanup Error Handling - EH handlers,
mptscsih_flush_cmds, and zeroing out ScsiLookup
from mptscsih_qcmd
* Cleanup asyn event handling from
mptscsih -> mptscsih_event_process. Also
added support for SAS Persistent Table Full,
an asyn event
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adds the actual mptsas driver, based upon the LSI driver with new work
for SAS transport class integration from Eric Moore and me.
This obviously depends on the SAS transport class.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- various bits for SAS support from the LSI driver.
- use the device private data for the fusion target private data.
this should be using the midlayer target data framework, but we
can't move over to that until fusion has been switched to the
generic DV code
- use target ID and channel from the fusion target private data,
because those in scsi_device will be different for mptsas
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Basically, this extends original dp264 fixup to all dp264 variations.
Here is one minor change: mask out bits 4-7 of a value assigned by SRM,
because
- newer consoles report ISA IRQs with offset 0xe0;
- even if console IRQ value is bogus, we'll have a value < 16
so it should be harmless as it won't clash with native IRQs.
Particularly this fixes USB interrupt problem on xp1000 and es40.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Acked-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Userspace SRQs don't have a buffer allocated for them in the kernel, so
it doesn't make sense to set srq->last during initialization. In fact,
this can crash trying to follow a nonexistent buffer pointer.
Signed-off-by: Roland Dreier <rolandd@cisco.com>