If we pass in a device which is higher than SNDRV_RAWMIDI_DEVICES then
the "next device" should be -1. This function just returns device + 1.
But the main thing is that "device + 1" can lead to a (harmless) integer
overflow and that annoys static analysis tools.
[fix the case for device == SNDRV_RAWMIDI_DEVICE by tiwai]
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PL022 SPI bus is sometimes used for early stuff like
regulators that need to be present at module_init() time, so
we move this to a subsys_initcall().
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Use netdev_alloc_skb_ip_align() helper and do correct allocation
Tested-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 30fff923 introduced in linux-2.6.33 (udp: bind() optimisation)
added a secondary hash on UDP, hashed on (local addr, local port).
Problem is that following sequence :
fd = socket(...)
connect(fd, &remote, ...)
not only selects remote end point (address and port), but also sets
local address, while UDP stack stored in secondary hash table the socket
while its local address was INADDR_ANY (or ipv6 equivalent)
Sequence is :
- autobind() : choose a random local port, insert socket in hash tables
[while local address is INADDR_ANY]
- connect() : set remote address and port, change local address to IP
given by a route lookup.
When an incoming UDP frame comes, if more than 10 sockets are found in
primary hash table, we switch to secondary table, and fail to find
socket because its local address changed.
One solution to this problem is to rehash datagram socket if needed.
We add a new rehash(struct socket *) method in "struct proto", and
implement this method for UDP v4 & v6, using a common helper.
This rehashing only takes care of secondary hash table, since primary
hash (based on local port only) is not changed.
Reported-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
During suspend, the power.completion is expected to be set when a
device has not yet started suspending. Set it on init to fix a
corner case where a device is resumed when its parent has never
suspended.
Consider three drivers, A, B, and C. The parent of A is C, and C
has async_suspend set. On boot, C->power.completion is initialized
to 0.
During the first suspend:
suspend_devices_and_enter(...)
dpm_resume(...)
device_suspend(A)
device_suspend(B) returns error, aborts suspend
dpm_resume_end(...)
dpm_resume(...)
device_resume(A)
dpm_wait(A->parent == C)
wait_for_completion(C->power.completion)
The wait_for_completion will never complete, because
complete_all(C->power.completion) will only be called from
device_suspend(C) or device_resume(C), neither of which is called
if suspend is aborted before C.
After a successful suspend->resume cycle, where B doesn't abort
suspend, C->power.completion is left in the completed state by the
call to device_resume(C), and the same call path will work if B
aborts suspend.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Changing state to CLOSING when FIN is received causes A0 cards to
hang. Fix this by checking for A0 cards in FIN handling.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the driver receives an AE for FIN received, it closes the
connection without changing the state of the connection in the
hardware to closing. By changing the state to closing, hardware will
do a normal close sequence.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During a stress testing in a large cluster, multiple close event are
detected and BUG() is hit in the iWARP core. The cause is that the
active node gave up while waiting for an MPA response from the peer
and tried to close the connection by sending RST. The passive node
driver receives the RST but is waiting for MPA response from the user.
When the MPA accept is received, the driver offloads the connection
and sends a CLOSE event. The driver gets an AE indicating RESET
received and also sends a CLOSE event, hitting a BUG().
Fix this by correcting RESET handling and sending CLOSE events.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Blackhole routes are used when xfrm_lookup() returns -EREMOTE (error
triggered by IKE for example), hence this kind of route is always
temporary and so we should check if a better route exists for next
packets.
Bug has been introduced by commit d11a4dc18b.
Signed-off-by: Jianzhao Wang <jianzhao.wang@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting TX pause param writes to the wrong register location causing
the adapter to hang. Correct the define used to write the reigster.
Addresses: https://bugs.openfabrics.org/show_bug.cgi?id=2116
Reported-by: Shiri Franchi <shirif@voltaire.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
cifs_demultiplex_thread sets the addr.sockAddr.sin_port without any
regard for the socket family. While it may be that the error in question
here never occurs on an IPv6 socket, it's probably best to be safe and
set the port properly if it ever does.
Break the port setting code out of cifs_fill_sockaddr and into a new
function, and call that from cifs_demultiplex_thread.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
If the tcpStatus is still CifsNew, the main cifs_demultiplex_loop can
break out prematurely in some cases. This is wrong as we will almost
always have other structures with pointers to the TCP_Server_Info. If
the main loop breaks under any other condition other than tcpStatus ==
CifsExiting, then it'll face a use-after-free situation.
I don't see any reason to treat a CifsNew tcpStatus differently than
CifsGood. I believe we'll still want to attempt to reconnect in either
case. What should happen in those situations is that the MIDs get marked
as MID_RETRY_NEEDED. This will make CIFSSMBNegotiate return -EAGAIN, and
then the caller can retry the whole thing on a newly reconnected socket.
If that fails again in the same way, the caller of cifs_get_smb_ses
should tear down the TCP_Server_Info struct.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
When cifs_demultiplex_thread exits, it does a number of cleanup tasks
including freeing the TCP_Server_Info struct. Much of the existing code
in cifs assumes that when there is a cisfSesInfo struct, that it holds a
reference to a valid TCP_Server_Info struct.
We can never allow cifsd to exit when a cifsSesInfo struct is still
holding a reference to the server. The server pointers will then point
to freed memory.
This patch eliminates a couple of questionable conditions where it does
this. The idea here is to make an -EINTR return from kernel_recvmsg
behave the same way as -ERESTARTSYS or -EAGAIN. If the task was
signalled from cifs_put_tcp_session, then tcpStatus will be CifsExiting,
and the kernel_recvmsg call will return quickly.
There's also another condition where this can occur too -- if the
tcpStatus is still in CifsNew, then it will also exit if the server
closes the socket prematurely. I think we'll probably also need to fix
that situation, but that requires a bit more consideration.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
This function is not used, so remove the definition and declaration.
Reviewed-by: Jeff Layton <jlayton@samba.org>
Signed-off-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
The VFS always checks that the source and target of a rename are on the
same vfsmount, and hence have the same superblock. So, this check is
redundant. Remove it and simplify the error handling.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
This reverts commit 9fbc590860.
The change to kernel crypto and fixes to ntlvm2 and ntlmssp
series, introduced a regression. Deferring this patch series
to 2.6.37 after Shirish fixes it.
Signed-off-by: Steve French <sfrench@us.ibm.com>
Acked-by: Jeff Layton <jlayton@redhat.com>
CC: Shirish Pargaonkar <shirishp@us.ibm.com>
This reverts commit 3ec6bbcdb4.
The change to kernel crypto and fixes to ntlvm2 and ntlmssp
series, introduced a regression. Deferring this patch series
to 2.6.37 after Shirish fixes it.
Signed-off-by: Steve French <sfrench@us.ibm.com>
Acked-by: Jeff Layton <jlayton@redhat.com>
CC: Shirish Pargaonkar <shirishp@us.ibm.com>
niu_get_ethtool_tcam_all() assumes that its output buffer is the right
size, and warns before returning if it is not. However, the output
buffer size is under user control and ETHTOOL_GRXCLSRLALL is an
unprivileged ethtool command. Therefore this is at least a local
denial-of-service vulnerability.
Change it to check before writing each entry and to return an error if
the buffer is already full.
Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 2d20ca8358.
The change to kernel crypto and fixes to ntlvm2 and ntlmssp
series, introduced a regression. Deferring this patch series
to 2.6.37 after Shirish fixes it.
Signed-off-by: Steve French <sfrench@us.ibm.com>
Acked-by: Jeff Layton <jlayton@redhat.com>
CC: Shirish Pargaonkar <shirishp@us.ibm.com>
The change to kernel crypto and fixes to ntlvm2 and ntlmssp
series, introduced a regression. Deferring this patch series
to 2.6.37 after Shirish fixes it.
This reverts commit c89e5198b2.
Signed-off-by: Steve French <sfrench@us.ibm.com>
Acked-by: Jeff Layton <jlayton@redhat.com>
CC: Shirish Pargaonkar <shirishp@us.ibm.com>
Add a call to of_node_put in the error handling code following a call to
of_find_compatible_node.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression x;
expression E,E1;
statement S;
@@
*x =
(of_find_node_by_path
|of_find_node_by_name
|of_find_node_by_phandle
|of_get_parent
|of_get_next_parent
|of_get_next_child
|of_find_compatible_node
|of_match_node
)(...);
...
if (x == NULL) S
<... when != x = E
*if (...) {
... when != of_node_put(x)
when != if (...) { ... of_node_put(x); ... }
(
return <+...x...+>;
|
* return ...;
)
}
...>
of_node_put(x);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
With the introduction of an AMBA PrimeCell per-cell block clock,
the pclk was left on after probe() unless explicitly disabled.
This clock is wired to the same clock on PL022 causing it to stay
always on since.
Fix this up properly by clocking the pclk whenever we want to
write into any PL022 registers and clocking the external clock
whenever we want to transmit messages on the bus.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Tested-by : Kevin Wells <wellsk40@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When using PIO we have a timeout for the TX and RX FIFOs to ensure that
the data actually gets transferred. Warn if we hit that timeout - it
should never happen, but this makes sure we'll find out if it does.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, mcheck: Avoid duplicate sysfs links/files for thresholding banks
io-mapping: Fix the address space annotations
x86: Fix the address space annotations of iomap_atomic_prot_pfn()
x86, mm: Fix CONFIG_VMSPLIT_1G and 2G_OPT trampoline
x86, hwmon: Fix unsafe smp_processor_id() in thermal_throttle_add_dev
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
gcc-4.6: kernel/*: Fix unused but set warnings
mutex: Fix annotations to include it in kernel-locking docbook
pid: make setpgid() system call use RCU read-side critical section
MAINTAINERS: Add RCU's public git tree
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, x86: Try to handle unknown nmis with an enabled PMU
perf, x86: Fix handle_irq return values
perf, x86: Fix accidentally ack'ing a second event on intel perf counter
oprofile, x86: fix init_sysfs() function stub
lockup_detector: Sync touch_*_watchdog back to old semantics
tracing: Fix a race in function profile
oprofile, x86: fix init_sysfs error handling
perf_events: Fix time tracking for events with pid != -1 and cpu != -1
perf: Initialize callchains roots's childen hits
oprofile: fix crash when accessing freed task structs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: fix lock annotations
fuse: flush background queue on connection close
Instead of, wrongly, reusing the 'val' variable, use a dedicated
one for reading the status register.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix compilation warning by typecasting the tx_buf pointer.
[I'm not thrilled with resorting to a cast; but I cannot see a better
way to go about this. I don't want to drop the const from struct
spi_transfer ~~glikely]
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Top of kvm_kpic_state structure should have the same memory layout as
kvm_pic_state since it is copied by memcpy.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
operand::val and operand::orig_val are 32-bit on i386, whereas cmpxchg8b
operands are 64-bit.
Fix by adding val64 and orig_val64 union members to struct operand, and
using them where needed.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
- Do not create expectation when forwarding the PORT
command to avoid blocking the connection. The problem is that
nf_conntrack_ftp.c:help() tries to create the same expectation later in
POST_ROUTING and drops the packet with "dropping packet" message after
failure in nf_ct_expect_related.
- Change ip_vs_update_conntrack to alter the conntrack
for related connections from real server. If we do not alter the reply in
this direction the next packet from client sent to vport 20 comes as NEW
connection. We alter it but may be some collision happens for both
conntracks and the second conntrack gets destroyed immediately. The
connection stucks too.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch: "gro: fix different skb headrooms" in its part:
"2) allocate a minimal skb for head of frag_list" is buggy. The copied
skb has p->data set at the ip header at the moment, and skb_gro_offset
is the length of ip + tcp headers. So, after the change the length of
mac header is skipped. Later skb_set_mac_header() sets it into the
NET_SKB_PAD area (if it's long enough) and ip header is misaligned at
NET_SKB_PAD + NET_IP_ALIGN offset. There is no reason to assume the
original skb was wrongly allocated, so let's copy it as it was.
bugzilla : https://bugzilla.kernel.org/show_bug.cgi?id=16626
fixes commit: 3d3be4333f
Reported-by: Plamen Petrov <pvp-lsts@fs.uni-ruse.bg>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Plamen Petrov <pvp-lsts@fs.uni-ruse.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 052dc7c45i "spi/dw_spi: conditional transfer mode change"
introduced cs_control code, which has a bug by using bit offset
for spi mode to set transfer mode in control register. Also it
forces devices who don't need cs_control to re-configure the
control registers for each spi transfer. This patch will fix them
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Allow interrupt sharing since exclusive interrupt line for
DW SPI controller is not provided on every platform.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
For small transfers at high speeds the expected transfer time can easily
be well under 1ms, causing the delay in wait_for_xfer() to be only the
dead reckoning fudge factor of 5ms currently included. Experiments on
some of my systems shows that this is marginal for some transfers so
double it to 10ms.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Allow the use of the S3C64xx SPI controller with things like PMICs by
moving the init up to subsys_initcall().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Dave Hylands reports:
| We've observed a problem with dma_alloc_writecombine when the system
| is under heavy load (heavy bus traffic). We've managed to reduce the
| problem to the following snippet, which is run from a kthread in a
| continuous loop:
|
| void *virtAddr;
| dma_addr_t physAddr;
| unsigned int numBytes = 256;
|
| for (;;) {
| virtAddr = dma_alloc_writecombine(NULL,
| numBytes, &physAddr, GFP_KERNEL);
| if (virtAddr == NULL) {
| printk(KERN_ERR "Running out of memory\n");
| break;
| }
|
| /* access DMA memory allocated */
| tmp = virtAddr;
| *tmp = 0x77;
|
| /* free DMA memory */
| dma_free_writecombine(NULL,
| numBytes, virtAddr, physAddr);
|
| ...sleep here...
| }
|
| By itself, the code will run forever with no issues. However, as we
| increase our bus traffic (typically using DMA) then the *tmp = 0x77
| line will eventually cause a page fault. If we add a small delay (a
| few microseconds) before the *tmp = 0x77, then we don't see a page
| fault, even under heavy load.
A dsb() is required after modifying the PTE entries to ensure that they
will always be visible. Add this dsb().
Reported-by: Dave Hylands <dhylands@gmail.com>
Tested-by: Dave Hylands <dhylands@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Check the argument name whether it is invalid (not C-like symbol name). This
makes event format simple.
Reported-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
LKML-Reference: <20100827113912.22882.62313.stgit@ltc236.sdl.hitachi.co.jp>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Set "argN" name for each argument automatically if it has no specified name.
Since dynamic trace event(kprobe_events) accepts special characters for its
argument, its format can show those special characters (e.g. '$', '%', '+').
However, perf can't parse those format because of the character (especially
'%') mess up the format. This sets "argX" name for those arguments if user
omitted the argument names.
E.g.
# echo 'p do_fork %ax IP=%ip $stack' > tracing/kprobe_events
# cat tracing/kprobe_events
p:kprobes/p_do_fork_0 do_fork arg1=%ax IP=%ip arg3=$stack
Reported-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
LKML-Reference: <20100827113906.22882.59312.stgit@ltc236.sdl.hitachi.co.jp>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Don't make argument names from raw parameters (means the parameters are written
in kprobe-tracer syntax), because the argument syntax may include special
characters. Just leave it, then kprobe-tracer gives a new name.
Reported-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20100827113859.22882.75598.stgit@ltc236.sdl.hitachi.co.jp>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Fix a bug to support %return probe syntax again. Previous commit 4235b04 has a
bug which disables the %return syntax on perf probe.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20100827113852.22882.87447.stgit@ltc236.sdl.hitachi.co.jp>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Fix a memory leak which happens when a field name conflicts with others. In
error case, free_trace_probe() will free all arguments until nr_args, so this
increments nr_args the begining of the loop instead of the end.
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
LKML-Reference: <20100827113846.22882.12670.stgit@ltc236.sdl.hitachi.co.jp>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
