1
Commit Graph

173 Commits

Author SHA1 Message Date
Paul Mundt
f966918724 sh: Kill off the remaining ST40 cruft.
The ST40 stuff in-tree hasn't built for some time, and hasn't been
updated for over 3 years. ST maintains their own out-of-tree changes
and rebases occasionally, and that's ultimately where all of the ST40
users go anyways.

In order for the ST40 code to be brought up to date most of the stuff
removed in this changeset would have to be rewritten anyways, so there's
very little benefit in keeping the remnants around either.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-11-07 11:13:55 +09:00
Paul Mundt
96a8a0ba12 sh: Fix up kgdb-on-NMI branch target.
This was all reworked some time ago, the old debug_enter was ripped
out with everything going through a debug trap jump table instead.
Kill off the debug_enter target and reference kgdb_handle_exception
directly.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-11-07 11:13:55 +09:00
Paul Mundt
b2078fa221 sh: Kill off dead ipr_irq_demux().
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-10-31 15:17:03 +09:00
Yoshihiro Shimoda
262feaa08e sh: Add resource of USBF for SH7722.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-10-30 13:05:31 +09:00
Stuart Menefy
24eb17e081 sh: clkfwk: Support multi-level clock propagation.
Currently clock propagation only works for one level, but we have some
clocks which need to propagate multiple levels, so make this recursive.

Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-28 11:51:52 +09:00
Paul Mundt
675bd7804c sh: Fix URAM start address on SH7785.
Not all of the SH-X2 URAM blocks are mapped in the same place,
SH7785 happens to map it on the opposite end of the address space
from SH7722, correct the addresses.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-27 18:22:21 +09:00
Paul Mundt
cb7af21f7d sh: Use boot_cpu_data for CPU probe.
This moves off of smp_processor_id() and only sets the probe
information for the boot CPU directly. This will be copied out
for the secondaries, so there's no reason to do this each time.

This also allows for some header tidying.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-27 18:18:39 +09:00
Paul Mundt
f72abd0a4c sh: Fix plat_irq_setup_pins() for SH7785.
There was some debug code left in here that caused the pin changes
to never be hit. Kill that off, and all is well.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-27 16:45:46 +09:00
Paul Mundt
26fad19d8c sh: Disable L2 reporting for present URAM only parts.
The probing logic works for both URAM and L2, with no way to
distinguish between the two. Disable the probing for now and
let the CPU subtypes that have this in a real L2 configuration
explicitly say so.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-27 10:29:58 +09:00
Paul Mundt
1a442fe02d sh: Initial SH-X3 SMP support.
This adds basic support for SH-X3 SMP (4 CPUs).

More IPI and cache debugging is necessary, mostly interfacing the
d-cache coherency and the I-cache broadcast invalidates. Only for
testing at present!

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 19:16:05 +09:00
Magnus Damm
ceb9b97451 sh: Hook up the SH-X3 SMP intc register groups.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 18:34:48 +09:00
Paul Mundt
aba1030a7e sh: Bring SMP support back from the dead.
There was a very preliminary bunch of SMP code scattered around for the
SH7604 microcontrollers from way back when, and it has mostly suffered
bitrot since then. With the tree already having been slowly getting
prepped for SMP, this plugs in most of the remaining platform-independent
bits.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 18:32:32 +09:00
Magnus Damm
f18d533e3c sh: intc - initial SMP support.
This implements initial support for the SMP INTC (particularly
INTC2) controllers.

These are largely implemented as conventional blocks, with
register sets grouped together at fixed strides relative to
the CPU id.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 18:16:42 +09:00
Paul Mundt
db2504966c sh: Wire up URAM node on SH7785.
Add SH7785 URAM as node 1, follows the SH-X3 change.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:55 +09:00
Paul Mundt
35f3abe976 sh: INTC stubs for SH7343 and SH7770 builds.
Get the SH7343 and SH7770 stuff linking again. Both of these still
require proper INTC support.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:53 +09:00
Magnus Damm
953c8ef250 sh: intc - irl mode update for sh7780 and sh7785
This patch contains the following fixes and improvements:
- Fix address typo for INTMSK2 / INTMSKCLR2 registers on sh7780.
- Adds IRQ_MODE_IRLnnnn_MASK using intc controller for IRL masking.
- Good old IRQ_MODE_IRLnnnn should not register any intc controller.
- plat_irq_setup_pins() now selects IRL or IRQ mode.
- the holding function is now disabled using ICR0.

By default all external pin interrupts are disabled.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:51 +09:00
Magnus Damm
1254d1db11 sh: remove CONFIG_CPU_HAS_INTC_IRQ
All processor specific interrupt code is now converted to make use
of the new intc code. The config option CONFIG_CPU_HAS_INTC_IRQ is
because of that pointless.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:51 +09:00
Paul Mundt
b05d1865b4 sh: Kill off volatile silliness in sq_flush_range().
CC      arch/sh/kernel/cpu/sh4/sq.o
arch/sh/kernel/cpu/sh4/sq.c: In function 'sq_flush_range':
arch/sh/kernel/cpu/sh4/sq.c:65: warning: passing argument 1 of 'prefetch' discards qualifiers from pointer target type

This didn't actually need to be volatile in the first place, so just
kill off the qualifier entirely.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:51 +09:00
Magnus Damm
2eb0303c2c sh: intc - add support for sh7206
This patch converts the cpu specific interrupt setup code for sh7206
from ipr to intc. New vectors are also added to match the information
provided by the datasheet.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:50 +09:00
Magnus Damm
0dc3fc04dd sh: intc - add support for sh7619
This patch converts the cpu specific interrupt setup code for sh7619
from ipr to intc. New vectors are also added to match the information
provided by the datasheet.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:50 +09:00
Magnus Damm
c4773bc2a0 sh: fix irqs for the second serial port on sh7206
This patch makes sure the serial port interrupt irqs matches the
datasheet.  Only irqs for SCIF1 are changed. While at some cosmetic
spaces are added.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:50 +09:00
Magnus Damm
3d37d94e5a sh: intc - primary priority masking fixes
This patch contains various intc fixes for problems reported by
Markus Brunner on the linuxsh-dev mailing list:

http://marc.info/?l=linuxsh-dev&m=118701948224991&w=1

Apart from added comments, the fixes are:

- add intc_set_priority() function prototype to hw_irq.h
- fix off-by-one error in intc_set_priority()
- make sure _INTC_WIDTH() is set for primary priority masking

Big thanks to Markus for finding these problems. Version two fixes
a compile error and an inverted primary check.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Markus Brunner <super.firetwister@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:50 +09:00
Magnus Damm
5c37e02535 sh: intc - mark data structures as __initdata
With the intc core improved it is now possible to put the intc data
structures in the initdata section.

Version two of this patch puts the __initdata inside DECLARE_INTC_DESC()
and removes the __initdata included in the board specific r2d code.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:50 +09:00
Magnus Damm
46420e49c9 sh: x3 - add ipi vectors
With the intc dual prio register support in place it is now possible
to add the ipi vectors to x3.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:50 +09:00
Magnus Damm
73505b445d sh: intc - rework core code
This patch reworks the intc core, implementing the following features:

- Support dual priority registers - one set and one clear register
- All 8/16/32 bit register combinations are now supported
- Both single mask and single enable bitmap register are supported
- Add code to set interrupt priority
- Speedup sense and priority configuration code
- Allocate data using bootmem, allows intc data structures to be
  __initdata
- Save memory - allocated memory footprint is smaller than intc
  structures

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:50 +09:00
Magnus Damm
6ef5fb2cfc sh: intc - add a clear register to struct intc_prio_reg
We need a secondary register member in struct intc_prio_reg to support
dual priority registers used by ipi on x3.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:49 +09:00
Magnus Damm
d6aee69ca1 sh: x3 - fix setup_bootmem_node() compile error with shx3_defconfig
This makes sure the function prototype for setup_bootmem_node() gets
included. The file setup-shx3.c does not compile otherwise for
CONFIG_NUMA=n.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:49 +09:00
Markus Brunner
3ea6bc3de4 sh: Add SH7720 CPU support.
This adds support for the SH7720 (SH3-DSP) CPU.

Signed-off by: Markus Brunner <super.firetwister@gmail.com>
Signed-off by: Mark Jonas <toertel@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:49 +09:00
Paul Mundt
d3428e9101 sh: Wire up CSM node for SH-X3.
Now that NODES_SHIFT is bumped up, we can plug in the CSM block as
a separate node, too.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:49 +09:00
Paul Mundt
6d64d4256c sh: intc: Fix sense regs oops for IRL IRQs.
IRL doesn't always define sense registers, so don't bother trying to
iterate through the table. This ended up causing an oops on SH-X3
when using IRL mode.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:48 +09:00
Magnus Damm
96290d808f sh: remove intc2 code
There is no point in keeping around the now unused intc2 code.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:48 +09:00
Magnus Damm
51da64264b sh: intc - add single bitmap register support
This patch adds single bitmap register support to intc. The current
code only handles 16 and 32 bit registers where a set bit means
interrupt enabled, but this is easy to extend in the future.

The INTC_IRQ() macro is also added to provide a way to hook in
interrupt controllers for FPGAs in boards or companion chips.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:47 +09:00
Magnus Damm
2635e8558a sh: intc - remove redundant irq code for shmin
This patch removes redundant interrupt code for the shmin board which
is using a sh770x processor and 4 IRQ lines as individual interrupts
(IRQ-mode).

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:47 +09:00
Magnus Damm
d59645d6ba sh: intc - remove redundant irq code for sh03, snapgear and titan
This patch removes redundant board specific interrupt code for boards
using sh775x processors and 4 IRQ lines in "Individual Interrupt Mode"
aka IRLM.

Three boards are affected: sh03, snapgear and titan.

The right way to do this is to use cpu specific code provided by intc.
A nice side effect is that sh03 now compiles, board not BROKEN any more.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:47 +09:00
Paul Mundt
ad89f87a84 rtc: rtc-sh: Support 4-digit year on SH7705/SH7710/SH7712.
All SH-4 parts have a 4-digit year, while the SH-3 parts typically
only use a 2-digit one. The SH7705, SH7710, and SH7712 SH-3 parts
however opted to extend it to 4-digit and still look and act like
an SH-3 RTC in all other ways.

This adds a capability flag (RTC_CAP_4_DIGIT_YEAR) that these
corner-case CPU subtypes can set in their platform data and cleans
up some of the ifdef mess in the driver as a result.

Reported-by: Markus Brunner <super.firetwister@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:47 +09:00
Paul Mundt
7da3b8ef66 sh: Initial multiple-node support for SH-X3.
Wire up CPU#0 URAM as node 1 on SH-X3.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:47 +09:00
Magnus Damm
1ee010087e sh: intc - add support for x3
This patch converts the cpu specific interrupt setup code for x3 from
intc2 to intc. New vectors are also added to match the preliminary
information.

Use plat_irq_setup_pins() to select between IRQ and IRL mode for IRQ0-3.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:47 +09:00
Magnus Damm
137b53b71c sh: intc - fix IRQ4 and IRQ5 typo on sh3
The intc tables for sh3 currently contain a typo where the bit
fields in IPRD are mixed up for IRQ4 and IRQ5. This patch makes
sure the correct bit fields are used - all according to the
datasheets.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:47 +09:00
Magnus Damm
e29bfbc443 sh: intc - add support for SH7760
This patch converts the cpu specific interrupt setup code for sh7760
from ipr + intc2 to intc. New vectors are also added to match the
information provided by the datasheet.

Vectors for IRQ4-IRQ7 are enabled by default. Use plat_irq_setup_pins()
if pins IRL0-3 should be used in IRLM mode.

The patch also adds the SIM block to the serial port platform data.
Version two of this patch fixes MMCIF problems reported by Manuel Lauss.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:46 +09:00
Magnus Damm
a0e23267d4 sh: intc - add support for SH7785
This patch converts the cpu specific interrupt setup code for sh7785
from intc2 to intc. New vectors are also added to match the information
provided by the datasheet.

No IRQ/IRL pin vectors are enabled by default. Use plat_irq_setup_pins()
to select between IRL and IRQ mode.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:46 +09:00
Paul Mundt
e7bd34a15b sh: Support explicit L1 cache disabling.
This reworks the cache mode configuration in Kconfig, and allows for
explicit selection of write-back/write-through/off configurations.
All of the cache flushing routines are optimized away for the off
case.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:46 +09:00
Magnus Damm
ac919986d7 sh: intc - avoid SH7710 specific vector on SH7712
This patch makes sure that the sh7710 specific ipsec vector is missing
if building for a sh7712. All according to the datasheet.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:46 +09:00
Magnus Damm
1301e71562 sh: intc - add missing vectors for SH7707
This patch adds a few missing vectors for sh7707. The only interrupt
controller differences between sh7707 and sh7709 seem to be added
vectors for one LCD controller and two PCMCIA slots.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:46 +09:00
Magnus Damm
ec58f1f32d sh: intc - add support for SH7706, SH7707, SH7708, SH7709
This patch unifies the cpu specific interrupt setup code for
sh7706, sh7707, sh7708 and sh7709 and moves the code into a new
file called setup-sh770x.c.  It makes sense to share the setup code
between these processors because most hardware blocks are identical
from a software point of view. With this patch the sh770x processors
now have a complete set of vectors that match with the information
provided by the data sheets. This is a big improvement for sh7708.

Vectors for IRQ4 and IRQ5 are enabled by default. Use
plat_irq_setup_pins() if pins IRQ0-3 should be used in IRQ mode.

This patch also unifies the platform device setup code which means
that the rtc driver now has platform data for all sh770x processors.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:46 +09:00
Magnus Damm
28b146c84e sh: intc - add support for SH7710
This patch converts the cpu specific interrupt setup code
for sh7710 from ipr to intc. While at it new vectors are added
to match the information provided by the datasheet. Version two
simplifies the Kconfig part.

Vectors for IRQ4 and IRQ5 are enabled by default. Use
plat_irq_setup_pins() if pins IRQ0-3 should be used in IRQ mode.

This patch also adds sh7710 specific platform data for the rtc
driver. The base address of SCIF1 is adjusted to match the
datasheet.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:45 +09:00
Magnus Damm
70e8be0a4e sh: intc - add support for SH7705
This patch converts the cpu specific interrupt setup code for
sh7705 from ipr to intc. While at it new vectors are added to
match the information provided by the datasheet.

Vectors for IRQ4 and IRQ5 are enabled by default.

Use plat_irq_setup_pins() if pins IRQ0-3 should be used in IRQ mode.

This patch also adds sh7705 specific platform data for the rtc driver.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-09-21 11:57:45 +09:00
Magnus Damm
b58d134c7f sh: missing symbol fix for sh4-202
This patch adds a plat_irq_setup() symbol for sh4-202. Without
this fix it is impossible to build a working kernel using the
microdev_defconfig.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-08-22 13:32:07 +09:00
Paul Mundt
c347d12cd1 sh: Fix lockdep debugging oops on SH-3/4.
In the SH-3/4 TLB access violation path we were enabling IRQs before
the call in to trace_hardirqs_on(), which ended up triggering:

        if (DEBUG_LOCKS_WARN_ON(!irqs_disabled()))
                return;

in kernel/lockdep.c:2031. Fix this up by removing the early re-enable,
we were already re-enabling IRQs post-trace_hardirqs_on() already, so
the semantics are now as was initially intended.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-08-01 16:17:07 +09:00
Magnus Damm
d89ddd1c84 sh: remove support for sh7300 and solution engine 7300
This patch removes old dead code:
- kill off sh7300 cpu support
- get rid of broken solution engine 7300 board support

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-07-26 15:37:57 +09:00
Paul Mundt
b067c50a7f sh: Silence sq compile warning on sh4 nommu.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-07-26 15:35:17 +09:00