em28xx_pre_card_setup() is meant to contain board-specific initialization. Also,
as autodetection sometimes occur only after having i2c bus enabled, this
function may need to be called later.
Moving those setups to happen outside the function avoids calling it twice without
need and without duplicating output lines at dmesg.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We don't know the xtal frequency of Silvercrest, but we need to have
some value in order to allow controlling the frame rate frequency. The
value is probably still wrong, since the manufacturer announces this
device as being capable of 30fps, but the maximum we can get is
13.5 fps.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to historical reasons, em28xx driver gets two consecutive frames and
fold them into an unique framing, doing interlacing. While this works
fine for TV images, this produces two bad effects with webcams:
1) webcam images are progressive. Merging two consecutive images produce
interlacing artifacts on the image;
2) since the driver needs to get two frames, it reduces the maximum
frame rate by two.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by hermann pitton <hermann-pitton@arcor.de>, some devices
has a different chip id for em2710 (likely the older ones):
em28xx: New device @ 480 Mbps (eb1a:2710, interface 0, class 0)
em28xx #0: Identified as EM2710/EM2750/EM2751 webcam grabber (card=22)
em28xx #0: em28xx chip ID = 17
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to hermann pitton <hermann-pitton@arcor.de> for pointing this new
variation.
Tested-by: hermann pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This device uses msp34xx and uses 2.048 MHz frequency for I2S
communication.
Thanks to Angelo Cano <acano@fastmail.fm> for pointing the issues with
this device and proposing an approach for fixing the issue.
Tested-by: Angelo Cano <acano@fastmail.fm>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some mt9v011 webcams report 0x8332 chip version, instead of 0x8243. From
the revision history at the mt9v011 datasheet, it seems that the chip
version has changed from the first release of the chip.
Thanks-to hermann pitton <hermann-pitton@arcor.de> for pointing this to
me, on his tests with a Silvercrest webcam.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Pinnacle Hybrid Pro 320e was missing a demod config for the xc3028, which
is required for digital tuning to work properly. Add the missing profile.
Thanks to Andreas Lunderhage for testing patches and providing a remote debug
environment.
Cc: Andreas Lunderhage <lunderhage@home.se>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In cases where the device has a generic Empia USB ID, the call in the
precard setup phase did not set the tuner GPIO. As a result, the tuner may
not be taken out of reset before attempting initialization in the analog
driver.
This problem was not seen before with the EVGA inDtube, since that particular
board has the analog GPIO setup to include taking the tuner out of reset.
Thanks to Andreas Lunderhage for testing patches and providing a remote debug
environment for the Pinnacle 320e.
Cc: Andreas Lunderhage <lunderhage@home.se>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set the GPIO properly for the analog side of the Pinnacle Hybrid Pro, or else
the emp202 doesn't get detected properly.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Setup the GPIOs properly and enable support for the DVB side of the Pinnacle
Hybrid Pro USB stick.
Thanks to Andreas Lunderhage for testing patches and providing a remote debug
environment.
Cc: Andreas Lunderhage <lunderhage@home.se>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Depending on the video input format, vinmode/vinctl needs adjustments.
For TV, this is not relevant, since the supported decoders output data
at the same format. However, webcam sensors may have different formats,
so, this needs to be adjusted based on the device.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In order to properly estimate fps, mt9v011 sensor driver needs to know
what is the used frequency on the sensor cristal. Adds the proper fields
and initialization code for specifying the cristal frequency.
Also, based on experimentation, it was noticed that the Silvercrest is
outputing data at 7 fps. This means that it should be using a 6.3 MHz
cristal. This information needs to be double checked later, by opening
the device. Anyway, by using this value for xtal, at least now we have
the correct fps report.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While trying to fix an mt9v001 webcam, I noticed that HSCALE/VSCALE do
work with em28xx + webcam. The issue is that the scaling setup depends
on the number of visible rows/cols of the input image.
With mt9v011 (Silvercrest), the resolution is 640x480. So, the scaling
is different from a normal TV image (720x480 on NTSC). This were causing
a wrong scaling and a previous patch disabled scaling.
As each sensor have their different resolution setting, the xres/yres
should be adjusted accordingly with the input sensor.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the previous approach, autodetection were working only for the two
generic entries (em275x and em2820 unknown ones). So, if someone would
try to force probing an specific device, the code would not properly run
the autodetection code.
With the new approach, the sensor autodetection will be run not only for
the two generic entries, but also do webcam specific ones.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using em28xx board decoder field for storing sensor information,
let's use instead a separate field for it.
Also, as sensors are currently autodetected, there's no need of having
it at the boards description. So, move it to the main em28xx struct.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Webcams in general don't have eeprom. So, the sensor hint code should be
called to properly detect what sensor is inside.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
By having the webcam devices marked as such, it will help the em28xx
driver to do the right thing on those devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just renames the flag, to use a clearer name. Later patches will use
this flag to properly set some drivers behaviors for webcams.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is one omitted unlock in em28xx_usb_probe. Fix that.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the code so that the zl10353 version of the Terratec Cinergy T XS USB
starts working again. This includes fixing what must have been a typo in the
GPIO definition for the digital side of the board, and setting of the
disable_i2c_gate_ctrl property for the zl10353 config, so that the i2c bus
doesn't get wedged the first time something tries to close the gate.
Also, add a printk() making clear that the mt352 version still isn't
supported. This issue is still being actively debugged, but in the meantime
at least the dmesg output will show a very clear error...
Thanks to Jelle de Jong for providing sample hardware to test with.
Thanks to Simon Kenyon for testing various patches and providing SSH access to
his environment so I could debug with access to a valid signal source.
Cc: Jelle de Jong <jelledejong@powercraft.nl>
Cc: Simon Kenyon <simon@koala.ie>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This webcam uses a em2710 chipset, that identifies itself as em2820,
plus a mt9v011 sensor, and a DY-301P lens.
It needs a few different initializations than a normal em28xx device.
Thanks to Hans de Goede <hdegoede@redhat.com> and Douglas Landgraf
<dougsland@redhat.com> for providing the acces for the webcam during
this weekend, I could make a patch for it while returning back from
FISL/Fudcom LATAM 2009.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an IR profile for the EVGA inDtube remote control (which is an NEC type
remote)
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the EVGA inDtube. Both ATSC and analog side validated as
fully functional.
Thanks to Jake Crimmins from EVGA for providing the correct GPIO info.
Thanks to Alan Hagge for doing all the device testing.
Thanks to Greg Williamson for providing hardware for testing.
Cc: Jake Crimmins <jcrimmins@evga.com>
Cc: Alan Hagge <ahagge@gmail.com>
Cc: Greg Williamson <cheeseboy16@gmail.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In cases where the board had a default USB ID, we would not indentify the
board until after the call to em28xx_set_mode(). As a result, for those
boards the analog GPIOs were not being set before probing the i2c bus for
devices (the probe would occur with the GPIOs being all high).
Make a call to em28xx_set_mode() so that the GPIOs are set properly before
probing the i2c bus for devices.
This problem was detected with the EVGA inDtube, where the tvp5150 is not
powered on unless GPIO1 is pulled low.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added tda9887_conf set up into em28xx_card_setup()
Signed-off-by: Franklin Meng <fmeng2002@yahoo.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an em28xx module option that allows a user to override the USB speed check.
Intended for advanced users who understand the consequences of trying to use
the device with a 12Mbps bus.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the KWorld 2800d work properly. In this case, that means making the
profile more generic so that it works for both the Pointnix Intra-Oral USB
camera and the KWorld device.
The device provides the audio through a pass-thru cable, so we don't need
an actual audio capture profile (neither the K-World device nor the Pointnix
have an onboard audio decoder).
Thanks to Paul Thomas for providing sample hardware.
Cc: Paul Thomas <pthomas8589@gmail.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em28xx basically just doesn't work at 12 Mbps. The isoc pipe needs
nearly 200 Mbps for analog support, so users would see garbage video, and on
the DVB/ATSC side scanning is likely to work but if the user tried to tune it
would certainly appear to have failed.
It's better to fail explicity up front and tell the user to plug into a USB 2.0
port, than to let the driver load and the user have weird problems with tuning
and garbage video.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For specific boards, pass initialization data to ir-kbd-i2c instead
of modifying the settings after the device is initialized. This is
more efficient and easier to read.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Let card drivers probe for IR receiver devices and instantiate them if
found. Ultimately it would be better if we could stop probing
completely, but I suspect this won't be possible for all card types.
There's certainly room for cleanups. For example, some drivers are
sharing I2C adapter IDs, so they also had to share the list of I2C
addresses being probed for an IR receiver. Now that each driver
explicitly says which addresses should be probed, maybe some addresses
can be dropped from some drivers.
Also, the special cases in saa7134-i2c should probably be handled on a
per-board basis. This would be more efficient and less risky than always
probing extra addresses on all boards. I'll give it a try later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the standard device driver binding model, the name field of
struct i2c_client is used to match devices to their drivers, so we
must stop using it for internal purposes. Define a separate field
in struct IR_i2c as a replacement, and use it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added EmpireTV entry.
Thanks to Xwang <xwang1976@email.it> to provide data for this board.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The functions v4l2_i2c_new_subdev and v4l2_i2c_new_probed_subdev relied on
i2c_get_adapdata to return the v4l2_device. However, this is not always
possible on embedded platforms. So modify the API to pass the v4l2_device
pointer explicitly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
s_standby is only used to put the tuner in powersaving mode, so move it
from core to tuner.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Converted em28xx driver to v4l2_subdev.
Thanks to Hans Verkuil <hverkuil@xs4all.nl> for helping this conversion.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The HVR-900 did not have a remote control defined, so it would not work. Add
the line for both versions of the product.
Thanks to Jens-Michael Hoffmann (#linuxtv user "jmho") for pointing out the
issue and testing the patch.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Compro VideoMate uses an external audio DSP chip, controlled via tvaudio
module (tda9874a). This patch improves em28xx infrastructure to support
an external audio processor and fixes the Compro VideoMate entry to work
with it.
Signed-off-by: Vitaly Wool <vital@embeddedalley.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added usb vendor/product id for Kaiser Baas Video to DVD maker.
Thanks to Trevor Campbell <tca42186@bigpond.net.au> for providing all data and tests needed to add this card to em28xx driver.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added SIIG AVTuner-PVR to the right entry.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Removed EM2821_BOARD_PROLINK_PLAYTV_USB2 entry.
This entry has a incorrect tuner set.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Vitaly Wool <vital@embeddedalley.com>:
> about half a year ago I posted the patch that basically enabled Compro
> VideoMate For You USB TV box support.
> The main problem is I couldn't get the sound working.
> So I kind of decomposed the box and found out the audio decoder chip
> used there was Philips TDA9874A. As far as I can see, it's not supported
> within the em28xx suite although it is for other TV tuner drivers.
A tvaudio modprobing confirms that tda9874a chip is accessible via i2c:
tvaudio: TV audio decoder + audio/video mux driver
tvaudio: known chips: tda9840, tda9873h, tda9874h/a, tda9850, tda9855, tea6300, tea6320, tea6420, tda8425, pic16c54 (PV951), ta8874z
tvaudio' 1-0058: chip found @ 0xb0
tvaudio' 1-0058: tvaudio': chip_read2: reg254=0x11
tvaudio' 1-0058: tvaudio': chip_read2: reg255=0x2
tvaudio' 1-0058: tda9874a_checkit(): DIC=0x11, SIC=0x2.
tvaudio' 1-0058: found tda9874a.
tvaudio' 1-0058: tda9874h/a found @ 0xb0 (em28xx #0)
tvaudio' 1-0058: tda9874h/a: chip_write: reg0=0x0
tvaudio' 1-0058: tda9874h/a: chip_write: reg1=0xc0
tvaudio' 1-0058: tda9874h/a: chip_write: reg2=0x2
tvaudio' 1-0058: tda9874h/a: chip_write: reg11=0x80
tvaudio' 1-0058: tda9874h/a: chip_write: reg12=0x0
tvaudio' 1-0058: tda9874h/a: chip_write: reg13=0x0
tvaudio' 1-0058: tda9874h/a: chip_write: reg14=0x1
tvaudio' 1-0058: tda9874h/a: chip_write: reg15=0x0
tvaudio' 1-0058: tda9874h/a: chip_write: reg16=0x14
tvaudio' 1-0058: tda9874h/a: chip_write: reg17=0x50
tvaudio' 1-0058: tda9874h/a: chip_write: reg18=0xf9
tvaudio' 1-0058: tda9874h/a: chip_write: reg19=0x80
tvaudio' 1-0058: tda9874h/a: chip_write: reg20=0x80
tvaudio' 1-0058: tda9874h/a: chip_write: reg24=0x80
tvaudio' 1-0058: tda9874h/a: chip_write: reg255=0x0
tvaudio' 1-0058: tda9874a_setup(): A2, B/G [0x00].
tvaudio' 1-0058: tda9874h/a: thread started]
This patch automatically loads tvaudio when needed (currently, only
with this board).
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added board Pinnacle Dazzle Video Creator Plus DVC107 to name description field.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
