There are some more conflicts than detected by git, namely support for
the newly added cpuimx machines needed to be converted to dynamic device
registration.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Conflicts:
arch/arm/mach-imx/Makefile
arch/arm/mach-imx/devices.c
arch/arm/mach-imx/devices.h
arch/arm/mach-imx/eukrea_mbimx27-baseboard.c
arch/arm/mach-mx2/Kconfig
arch/arm/mach-mx25/Makefile
arch/arm/mach-mx25/devices.c
arch/arm/plat-mxc/include/mach/mx25.h
arch/arm/plat-mxc/include/mach/mxc_nand.h
i.MX25's OTG has the same USBCTRL registers than i.MX35 so reuse
most of the i.MX35's defines.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As the kernel contains a copy of the GPL anyhow just get rid of the address
specification instead of fixing it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This patch adds USB HW initializiation code to /plat-mxc/ehci.c.
-Sets some specific PHY settings
Renames mxc_set_usbcontrol to mxc_initialize_usb_hw.
Adds new register bit defines for the USB HW on Freescale
SoCs.
This patch applies to 2.6.34-rc6.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Reviewed-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- The SIC mask is only 2bits wide, not 4
- MX31_OTG_PM_BIT and MX31_H1_PM_BIT use negative logic
- clear MX31_H1_DT_BIT and MX31_H2_DT_BIT so that they can be cleared,
not only set.
- return -EINVAL if called with an invalid controller number
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Magnus Lilja <lilja.magnus@gmail.com>
The Freescale MX27 and MX31 SoCs have a EHCI controller onboard.
The controller is capable of USB on the go. This patch adds
a driver to support all three of them.
Users have to pass details about serial interface configuration in the
platform data.
The USB OTG core used here is the ARC core, so the driver should
be renamed and probably be merged with ehci-fsl.c eventually.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
