The DM9000's internal PHY reports a copy of the link status
in the NSR register of the chip. Reading the status when
polling for link status is faster as it eliminates the need
to sleep, but does not print as much information.
Add an platform flag to force this behaviour, and a Kconfig
option to allow it to be forced to the faster method always.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The DM9000_NSR register contains a copy of the internal PHY's
link status which we can use to determine if the link is up
or down. This eliminates the more costly (and sleeping) PHY
read when using the DM9000's own PHY.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cleanup the source code by moving the code around to avoid
having to declare the functions before they are used.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cleanup bits of the DM9000 driver to make the code
neater and easier to read. This is includes removing
some old definitions, re-indenting areas, etc.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove the now extraneous checks in dm9000_release_board()
now that the two-resource case is removed. Also remove the
check on pdev->num_resources, as we check the return data
from platform_get_resource() to ensure we have not only
the right number but the right type of resources as well.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add support for both the DM9000A and DM9000B versions of
the DM9000 networking chip. This includes adding support
for the Link-Change IRQ which is used instead of polling
the PHY every 2 seconds.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The dm9000 driver accepts either 2 or 3 resources to describe the platform
devices. The 2 resources case abuses the ioresource mechanism by passing
ioremap()ed memory through the platform device resources. This patch removes
that case and converts boards that were using it to the 3 resources scheme.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
use cancel_delayed_work_sync()
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Periodically check the MII PHY status to ensure that the
network layer's link status is updated and the user informed
of any changes.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There was a missing newline in a dev_dbg() message. Values read
from/written into PHY registers might be for interest too, so I added
new dbg messages there.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There were missing __dev* annotations for the dm9000_probe()
and dm9000_drv_remove() functions.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Since 43cc71eed1, the platform modalias is
prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable network
platform drivers, to re-enable auto loading.
NOTE: didn't change drivers/net/fs_enet/fs_enet-main.c "old binding" support.
That looks problematic in the first place (it even uses the ancient "struct
device_driver" binding scheme for platform_bus!) and I suspect it will vanish
soonish when arch/powerpc rules the world. Also, drivers/net/ne.c would have
needed more thought to sort out.
[akpm@linux-foundation.org: fix sgiseeq.c]
[dbrownell@users.sourceforge.net: more drivers, registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Vitaly Bordug <vitb@kernel.crashing.org>
Cc: Dale Farnsworth <dale@farnsworth.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Victor <andrew@sanpeople.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Show whether the MAC address was read from the EEPROM or
the onboard PAR registers.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reading the ID register does not always return the correct ID
from the device, so we retry several times to see if we get
a correct value.
These failures seem to be excaserbated by the speed of the
access to the chip (possibly time between issuing the address
and then the data cycle).
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add entry to handle the MII ioctl() calls via the
generic_mii_ioctl call.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Allow the platform data to specify to the DM9000 driver
that there is no posibility of an attached EEPROM on the
device, so default all reads to 0xff and ignore any
write operations.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The writing of the data should implicitly truncate
the data to 8bits, so do not bother with the ands
in the code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove the cal_CRC as this is basically wrappering the
ether_crc_le function, and is only being used by the
multicast hash table functions.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The code was using a delay of 8ms, when it should have been
using the EEPROM status flag from the device to indicate the
EEPROM transaction had finished.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the netif_msg_*() macros to enable the debugging based
on the board's msg_enable field. The output still goes via
the dev_dbg() macros, so will be tagged and output as
appropriate.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We have a perfectly good version control system, so we do not
need to duplicate change comments in the header for this code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ensure we hold the spinlock whilst the registers and being
modified even though we hold the overall lock. This should
protect against an interrupt happening whilst we are using
the device.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove the old hack to program an initial EEPROM setting
into the DM9000 as we now have ethtool support for reading
and writing the EEPROM.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Allow the msg_enable value to be read and written by
the ethtool interface.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add ethtool support to access the configuration EEPROM
connected to the DM9000.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add a mutex to serialise access to the chip functions from
entries such as the ethtool and the MII code. This should
reduce the amount of time the spinlock is held to protect
the address register.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The srom array in the board data is only being used in the device probe
routines. The probe also only uses the first 6 bytes of an array
we spend 512ms reading 128 bytes from. Change to reading the
MAC area directly to the MAC address structure.
As a side product, we rename the read_srom_word to dm9000_read_eeprom
to bring it into line with the rest of the driver. No change is made
to the delay in this function, which will be dealt with in a later
patch.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We can use sleeping functions when reading and writing the
PHY registers, so let us sleep instead of busy waiting for
the PHY.
Note, this also fixes a bug reading the PHY where only 100uS
was being used instead of 150uS
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The phy read and write routines call udelay() with the board
lock held, and with the posibility of IRQs being disabled. Since
these delays can be up to 500usec, and are only required as we
have to save the chip's address register.
To improve the behaviour, hold the lock whilst we are writing
and then restore the state before the delay and then repeat
the process once the delay has happened.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove the timer based MII phy polling, as this is
currently broken with the new EEPROM code that now
uses mutexes to protect the phy access.
This will need to be replaced in the future by some
form of mutex safe mechanism for reading the MII
phy status.
The replacement has not been done here as changing
this patch, which is early in the sequence has quite
a knock-on effect. Once this series is merged, then
a new presentation of an patch to poll the MII link
status can be added.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the flags in the IRQ resource to specify the type of
IRQ being requested, so that systems which do not have
level-based interrupts, or change the interrupt in some
other way can specify this without making an #ifdef mess
in the driver.
This is specifically designed to undo the change in commit
4e4fc05a2b which hardwires the
type for everyone but blackfin to IRQT_RISING, which breaks
all a number of Simtec boards which use (and setup in the
bootloader) active low IRQs.
Note, although there where originally objections due to
the use of IORESOURCE_IRQ and IRQT_ flags not sharing the
same definition, at least <include/linux/interrupt.h> notes
these are the same.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
CC: Daniel Mack <daniel@caiaq.de>
CC: Bryan Wu <bryan.wu@analog.com>
CC: Alex Landau <landau.alex@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change the debug macros to use the compiler to elide any
unnecessary debug level, and to allow device configurable
debug control.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move to using dev_dbg() and friends for the output of
information to the user.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch from: Laurent Pinchart <laurentp@cse-semaphore.com>
This patch adds a flag to the DM9000 platform data which, when set,
configures the device to use an external PHY.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Ben Dooks <ben-linuy@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch from: Laurent Pinchart <laurentp@cse-semaphore.com>
This patch splits the receive status in 8bit wide fields and convert the
packet length from little endian to CPU byte order.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support for Toradex' PXA27x based Colibri module.
It's kept as simple as possible to only provide basic functionality.
A default config is also included.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
DM9000 driver returns success even if it is failed to detect the chip.
Below patch fixes it.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
drivers/net/dm9000.c | 6 +++---
1 files changed, 3 insertions(+), 3 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We now have struct net_device_stats embedded in struct net_device,
and the default ->get_stats() hook does the obvious thing for us.
Run through drivers/net/* and remove the driver-local storage of
statistics, and driver-local ->get_stats() hook where applicable.
This was just the low-hanging fruit in drivers/net; plenty more drivers
remain to be updated.
[ Resolved conflicts with napi_struct changes and fix sunqe build
regression... -DaveM ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When transferring data at full speed, the DM9000 network interface
sometimes stops sending/receiving data. Worse, ksoftirqd consumes
100% cpu and the net tx watchdog never triggers.
Fix by spin_lock_irqsave() in dm9000_start_xmit() to prevent the
interrupt handler from interfering.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The DM9000 network driver is calling kfree() on an netdev
causing the system to oops if the probe fails. The right
thing to do is call free_netdev().
Thanks to Russell King for spotting this.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
