1
Commit Graph

427 Commits

Author SHA1 Message Date
Arjan van de Ven
2b8693c061 [PATCH] mark struct file_operations const 3
Many struct file_operations in the kernel can be "const".  Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data.  In addition it'll catch accidental writes at compile time to
these shared resources.

Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-12 09:48:45 -08:00
Michael S. Tsirkin
839fcaba35 IPoIB: Connected mode experimental support
The following patch adds experimental support for IPoIB connected
mode, as defined by the draft from the IETF ipoib working group.  The
idea is to increase performance by increasing the MTU from the maximum
of 2K (theoretically 4K) supported by IPoIB on top of UD.  With this
code, I'm able to get 800MByte/sec or more with netperf without
options on a Mellanox 4x back-to-back DDR system.

Some notes on code:
1. SRQ is used for scalability to large cluster sizes
2. Only RC connections are used (UC does not support SRQ now)
3. Retry count is set to 0 since spec draft warns against retries
4. Each connection is used for data transfers in only 1 direction, so
   each connection is either active(TX) or passive (RX).  2 sides that
   want to communicate create 2 connections.
5. Each active (TX) connection has a separate CQ for send completions -
   this keeps the code simple without CQ resize and other tricks
6. To detect stale passive side connections (where the remote side is
   down), we keep an LRU list of passive connections (updated once per
   second per connection) and destroy a connection after it has been
   unused for several seconds. The LRU rule makes it possible to avoid
   scanning connections that have recently been active.

Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-02-10 08:00:48 -08:00
Al Viro
b437735645 [PATCH] iscsi endianness annotations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-09 09:14:07 -08:00
Greg Kroah-Hartman
43cb76d91e Network: convert network devices to use struct device instead of class_device
This lets the network core have the ability to handle suspend/resume
issues, if it wants to.

Thanks to Frederik Deweerdt <frederik.deweerdt@gmail.com> for the arm
driver fixes.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 10:37:11 -08:00
Ishai Rabinovitz
1033ff670d IB/srp: Don't wait for response when QP is in error state.
When there is a call to send_tsk_mgmt SRP posts a send and waits for 5
seconds to get a response.

When the QP is in the error state it is obvious that there will be no
response so it is quite useless to wait.  In fact, the timeout causes
SRP to wait a long time to reconnect when a QP error occurs. (Each
abort and each reset_device calls send_tsk_mgmt, which waits for the
timeout).  The following patch solves this problem by identifying the
failure and returning an immediate error code.

Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-02-04 14:11:56 -08:00
Ishai Rabinovitz
a20f3a6d7e IB/srp: Check match_strdup() return
Checks if the kmalloc in match_strdup() was successful, and bail out
on looking at the token if it failed.

Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-01-22 17:03:54 -08:00
Erez Zilber
f0938401f2 IB/iser: Return error code when PDUs may not be sent
iSER limits the number of outstanding PDUs to send. When this threshold
is reached, it should return an error code (-ENOBUFS) instead of setting
the suspend_tx bit (which should be used only by libiscsi).

Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-01-07 10:15:15 -08:00
Roland Dreier
bf628dc22a IB/srp: Fix FMR mapping for 32-bit kernels and addresses above 4G
struct srp_device.fmr_page_mask was unsigned long, which means that
the top part of addresses above 4G was being chopped off on 32-bit
architectures.  Of course nothing good happens when data from SRP
targets is DMAed to the wrong place.

Fix this by changing fmr_page_mask to u64, to match the addresses
actually used by IB devices.

Thanks to Brian Cain <Brian.Cain@ge.com> and David McMillen
<davem@systemfabricworks.com> for help diagnosing the bug and testing
the fix.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-12-15 14:01:49 -08:00
Roland Dreier
82b399133b IPoIB: Make sure struct ipoib_neigh.queue is always initialized
Move the initialization of ipoib_neigh's skb_queue into
ipoib_neigh_alloc(), since commit 2745b5b7 ("IPoIB: Fix skb leak when
freeing neighbour") will make iterate over the skb_queue to free any
packets left over when freeing the ipoib_neigh structure.

This fixes a crash when freeing ipoib_neigh structures allocated in
ipoib_mcast_send(), which otherwise don't have their skb_queue
initialized.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-12-12 14:48:18 -08:00
Ralph Campbell
5180311fe9 IB/iser: Use the new verbs DMA mapping functions
Convert iSER to use the new verbs DMA mapping functions for kernel
verbs consumers.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-12-12 14:31:00 -08:00
Ralph Campbell
85507bcce0 IB/srp: Use new verbs IB DMA mapping functions
Convert SRP to use the new verbs DMA mapping functions for kernel
verbs consumers.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-12-12 14:30:55 -08:00
Ralph Campbell
37ccf9df97 IPoIB: Use the new verbs DMA mapping functions
Convert IPoIB to use the new DMA mapping functions
for kernel verbs consumers.

Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-12-12 14:30:48 -08:00
Roland Dreier
dee234f48a IB/iser: Remove unused "write-only" variables
Remove variables that are set but then never looked at in the iSER
initiator.  These cleanups came from David Binderman's list of "set
but never used" warnings from icc.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-12-12 11:50:20 -08:00
David Howells
f0d1b0b30d [PATCH] LOG2: Implement a general integer log2 facility in the kernel
This facility provides three entry points:

	ilog2()		Log base 2 of unsigned long
	ilog2_u32()	Log base 2 of u32
	ilog2_u64()	Log base 2 of u64

These facilities can either be used inside functions on dynamic data:

	int do_something(long q)
	{
		...;
		y = ilog2(x)
		...;
	}

Or can be used to statically initialise global variables with constant values:

	unsigned n = ilog2(27);

When performing static initialisation, the compiler will report "error:
initializer element is not constant" if asked to take a log of zero or of
something not reducible to a constant.  They treat negative numbers as
unsigned.

When not dealing with a constant, they fall back to using fls() which permits
them to use arch-specific log calculation instructions - such as BSR on
x86/x86_64 or SCAN on FRV - if available.

[akpm@osdl.org: MMC fix]
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Howells <dhowells@redhat.com>
Cc: Wojtek Kaniewski <wojtekka@toxygen.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:28:51 -08:00
David Howells
9db7372445 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:

	drivers/ata/libata-scsi.c
	include/linux/libata.h

Futher merge of Linus's head and compilation fixups.

Signed-Off-By: David Howells <dhowells@redhat.com>
2006-12-05 17:01:28 +00:00
David Howells
4c1ac1b491 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:

	drivers/infiniband/core/iwcm.c
	drivers/net/chelsio/cxgb2.c
	drivers/net/wireless/bcm43xx/bcm43xx_main.c
	drivers/net/wireless/prism54/islpci_eth.c
	drivers/usb/core/hub.h
	drivers/usb/input/hid-core.c
	net/core/netpoll.c

Fix up merge failures with Linus's head and fix new compilation failures.

Signed-Off-By: David Howells <dhowells@redhat.com>
2006-12-05 14:37:56 +00:00
Al Viro
a1f8e7f7fb [PATCH] severing skbuff.h -> highmem.h
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2006-12-04 02:00:29 -05:00
Michael S. Tsirkin
2745b5b713 IPoIB: Fix skb leak when freeing neighbour
ipoib_neigh_free() is sometimes called while neighbour is still alive,
so it might still have queued skbs.  Fix skb leak in this case.

Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-11-29 15:33:09 -08:00
Vu Pham
d2fcea7d68 IB/srp: Fix memory leak on reconnect
SRP reallocates the IU buffers for tx_ring and rx_ring without freeing
the old buffers when it reconnects to a target.  Fix this by keeping
the old IU buffers around.

Signed-off-by: Vu Pham <vu@mellanox.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-11-29 15:33:09 -08:00
Roland Dreier
e54f81889c IB: Convert kmem_cache_t -> struct kmem_cache
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-11-29 15:33:07 -08:00
Arne Redlich
3c8edf0eca IB/srp: Increase supported CDB size
Set the Scsi_Host's max_cmd_len from 12 (default) to 16 for
SRP. Otherwise scsi_dispatch_cmd() won't pass down certain commands
such as READ CAPACITY 16, required for supporting disks > 2TB.

Signed-off-by: Arne Redlich <arne.redlich@xiranet.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-11-29 15:33:06 -08:00
David Howells
c4028958b6 WorkStruct: make allyesconfig
Fix up for make allyesconfig.

Signed-Off-By: David Howells <dhowells@redhat.com>
2006-11-22 14:57:56 +00:00
Michael S. Tsirkin
073ae841d6 IPoIB: Clear high octet in QP number
IPoIB assumes that high (reserved) octet in the hardware address is 0,
and copies it into the QPN.  This violates RFC 4391 (which requires
that the high 8 bits are ignored on receive), and will result in an
invalid QPN being used when interoperating with IPoIB connected mode.

Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-11-16 13:56:45 -08:00
Erez Zilber
2e7a742628 IB/iser: Start connection after enabling iSER
When a connection is started (a new connection or a recovered one),
iSER should prepare its resources for full-featured mode and only then
notify the iSCSI layer that it is ready to start queueing commands.

Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-10-30 20:52:50 -08:00
Roland Dreier
73fbe8be73 IPoIB: Check for DMA mapping error for TX packets
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-10-10 12:50:38 -07:00
Ishai Rabinovitz
01cb9bcbd3 IB/srp: Enable multiple connections to the same target
Enable multiple concurrent connections to the same SRP target:

1) Use port GUID instead of node GUID in the initiator port
   identifier.  This allows connections to be made from multiple HCA
   ports at the same time.
2) Let the user specify the identifier extention when adding the
   device.  This allows userspace to make multiple connections even
   from the same port, if it wants too.

Without this, only one connection can be made from any given HCA, even
if it has multiple ports, because we don't use multi-channel mode, so
targets will only allow one connection from a given initiator port ID.

Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-10-10 12:49:05 -07:00
Ishai Rabinovitz
9b0af401aa IB/srp: Remove redundant memset()
scsi_host_alloc() already allocates with kzalloc(), so the struct Scsi_Host
is zeroed out, including the private data portion.  Remove the redundant
memset that zeros this out again in the SRP initiator.

Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-10-10 09:51:14 -07:00
Matt LaPlante
cab00891c5 Still more typo fixes
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-10-03 22:36:44 +02:00
Erez Zilber
fd6a79a786 IB/iser: Fix the description of iSER in Kconfig
Fix the description of iSER in Kconfig.  It is not accurate.

Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-09-28 10:54:51 -07:00
Erez Zilber
74a2078061 IB/iser: DMA unmap unaligned for RDMA data before touching it
iSER uses the DMA mapping api to map the page holding the
SCSI command data to the HCA DMA address space. When the
command data is not aligned for RDMA, the data is copied
to/from an allocated buffer which in turn is used for
executing this command. The pages associated with the
command must be unmapped before being touched.

Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-09-28 10:53:18 -07:00
Erez Zilber
87e8df7a27 IB/iser: Have iSER data transaction object point to iSER conn
iSER uses a data transaction object (struct iser_dto) as part
of its IB data descriptors (struct iser_desc) management.
It also uses a hierarchy of connection structures pointing to
each other. A DTO may exist even after the iscsi_iser connection
pointed by it is destroyed (eg one that is bound to a post
receive buffer which was flushed by the IB HW). Hence DTOs need
point to the lowest connection, which is struct iser_conn.

Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-09-28 10:53:16 -07:00
Theodore Ts'o
8e18e2941c [PATCH] inode_diet: Replace inode.u.generic_ip with inode.i_private
The following patches reduce the size of the VFS inode structure by 28 bytes
on a UP x86.  (It would be more on an x86_64 system).  This is a 10% reduction
in the inode size on a UP kernel that is configured in a production mode
(i.e., with no spinlock or other debugging functions enabled; if you want to
save memory taken up by in-core inodes, the first thing you should do is
disable the debugging options; they are responsible for a huge amount of bloat
in the VFS inode structure).

This patch:

The filesystem or device-specific pointer in the inode is inside a union,
which is pretty pointless given that all 30+ users of this field have been
using the void pointer.  Get rid of the union and rename it to i_private, with
a comment to explain who is allowed to use the void pointer.  This is just a
cleanup, but it allows us to reuse the union 'u' for something something where
the union will actually be used.

[judith@osdl.org: powerpc build fix]
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Judith Lebzelter <judith@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-09-27 08:26:17 -07:00
James Bottomley
c9802cd957 Merge mulgrave-w:git/scsi-misc-2.6
Conflicts:

	drivers/scsi/iscsi_tcp.c
	drivers/scsi/iscsi_tcp.h

Pretty horrible merge between crypto hash consolidation
and crypto_digest_...->crypto_hash_... conversion

Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-09-23 15:33:43 -05:00
Eli Cohen
a8bfca0243 IPoIB: Add some likely/unlikely annotations in hot path
Signed-off-by: Eli Cohen <eli@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-09-22 15:22:58 -07:00
Dotan Barak
507c335046 IPoIB: Remove unused include of vmalloc.h
IPoIB doesn't use anything from <linux/vmalloc.h>, so don't include it.

Signed-off-by: Dotan Barak <dotanb@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-09-22 15:22:57 -07:00
Eli Cohen
5ccd025553 IPoIB: Rejoin all multicast groups after a port event
When ipoib_ib_dev_flush() is called because of a port event, the
driver needs to rejoin all multicast groups, since the flush will call
ipoib_mcast_dev_flush() (via ipoib_ib_dev_down()).  Otherwise no
(non-broadcast) multicast groups will be rejoined until the networking
core calls ->set_multicast_list again, and so multicast reception will
be broken for potentially a long time.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-09-22 15:22:56 -07:00
Roland Dreier
d0df6d6d45 IPoIB: Create MCGs with all attributes required by RFC
RFC 4391 ("Transmission of IP over InfiniBand (IPoIB)") says:

  If the IB multicast group does not already exist, one must be
  created first with the IPoIB link MTU.  The MGID MUST use the same
  P_Key, Q_Key, SL, MTU, and HopLimit as those used in the
  broadcast-GID.  The rest of attributes SHOULD follow the values used
  in the broadcast-GID as well.

However, the current IPoIB driver is only setting the attributes
required by the InfiniBand spec to create a multicast group, so in
particular the MTU and HopLimit are not being set.  Add these
attributes when creating MCGs, and also set the Rate attribute, since
IPoIB pays attention to that attribute as well.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-09-22 15:22:56 -07:00
Roland Dreier
5755d6dad9 IB/iser: INFINIBAND_ISER depends on INET
iSER won't build without CONFIG_INET enabled, so make Kconfig reflect that.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-09-22 15:22:55 -07:00
Michael S. Tsirkin
c1a0b23bf4 IB/sa: Require SA registration
Require users to register with SA module, to prevent the sa_query
module text from going away while an SA query callback is still
running.  Update all in-tree users for the new interface.

Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-09-22 15:22:53 -07:00
Roland Dreier
2439a6e65f IPoIB: Refactor completion handling
Split up ipoib_ib_handle_wc() into ipoib_ib_handle_rx_wc() and
ipoib_ib_handle_tx_wc() to make the code easier to read.  This will
also help implement NAPI in the future.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-09-22 15:22:52 -07:00
Erez Zilber
d81110285f IB/iser: Do not use FMR for a single dma entry sg
Fast Memory Registration (fmr) is used to register for rdma an sg whose
elements are not linearly sequential after dma mapping.

The IB verbs layer provides an "all dma memory MR (memory region)" which
can be used for RDMA-ing a dma linearly sequential buffer.

Change the code to use the dma mr instead of doing fmr when dma mapping
produces a single dma entry sg.

Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-09-22 15:22:52 -07:00
Erez Zilber
e981f1d4b8 IB/iser: fix some debug prints
fix and add some debug prints related to iser
handling of memory for rdma.

Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-09-22 15:22:51 -07:00
Erez Zilber
8dfa0876d3 IB/iser: make FMR "page size" be 4K and not PAGE_SIZE
As iser is able to use at most one rdma operation for the
execution of a scsi command, and registration of the sg
associated with scsi command has its restrictions, the code
checks if an sg is "aligned for rdma".

Alignment for rdma is measured in "fmr page" units whose
possible resolutions are different between HCAs and can be
smaller, equal or bigger to the system page size.

When the system page size is bigger than 4KB (eg the default
with ia64 kernels) there a bigger chance that an sg would be
aligned for rdma if the fmr page size is 4KB.

Change the code to create FMR whose pages are of size 4KB
and to take that into account when processing the sg.

Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-09-22 15:22:51 -07:00
Erez Zilber
8072ec2f8f IB/iser: Limit the max size of a scsi command
Currently, the data length of a command coming down from scsi-ml
is limited only by the size of its sg list (sg_tablesize). The
max data length may be different for different page size values.
By setting max_sectors, we limit the data length to
max_sectors*512 bytes.

Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-09-22 15:22:50 -07:00
Erez Zilber
777a71dd4d IB/iser: fix a check of SG alignment for RDMA
dma mapping may include a "compaction" of the sg associated with scsi command.
Hence, the size of the maximal prefix of the SG which is aligned for rdma must be
compared against the length of the dma mapped sg (mem->dma_nents) and not against
the size of it before it was mapped (mem->size).

Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-09-22 15:22:49 -07:00
Tom Tucker
07ebafbaaa RDMA: iWARP Core Changes.
Modifications to the existing rdma header files, core files, drivers,
and ulp files to support iWARP, including:
 - Hook iWARP CM into the build system and use it in rdma_cm.
 - Convert enum ib_node_type to enum rdma_node_type, which includes
   the possibility of RDMA_NODE_RNIC, and update everything for this.

Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-09-22 15:22:47 -07:00
Roland Dreier
3cd965646b IB: Whitespace fixes
Remove some trailing whitespace that has snuck in despite the best
efforts of whitespace=error-all.  Also fix a few other whitespace
bogosities.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-09-22 15:22:46 -07:00
Ishai Rabinovitz
ded7f1a16d IB/srp: Add port/device attributes
Add local_ib_device and local_ib_port attributes to srp scsi_host.
These are needed when we want to connect to the same target through
multiple distinct ports.

Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-09-22 15:17:21 -07:00
Michael S. Tsirkin
9217b27b12 IB/ipoib: Fix flush/start xmit race (from code review)
Prevent flush task from freeing the ipoib_neigh pointer, while
ipoib_start_xmit() is accessing the ipoib_neigh through the pointer it
has loaded from the skb's hardware address.

Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-09-22 15:17:18 -07:00
Eli Cohen
c11bd42a76 IPoIB: Retry failed send-only multicast group joins
When a send-only multicast group join fails, mcast->query must be set
to NULL.  Otherwise, IPoIB will never retry the join and the multicast
group will never be reachable.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-09-14 13:51:41 -07:00
Ishai Rabinovitz
add7afc756 IB/srp: Don't schedule reconnect from srp
If there is a problem in the connection, the SCSI mid-layer will
eventually call srp_reset_host(), which will call srp_reconnect(), so
we do not need to schedule a call to srp_reconnect_work() from
srp_completion().

Removing this prevents srp_reset_host() from failing if a reconnect
scheduled from srp_completion() is already in progress, which in turn
was causing crashes as both SCSI midlayer and srp_reconnect() were
cancelling commands.

Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-09-14 13:51:40 -07:00
Mike Christie
ffd0436ed2 [SCSI] libiscsi, iscsi_tcp, iscsi_iser: check that burst lengths are valid.
iSCSI RFC states that the first burst length must be smaller than the
max burst length. We currently assume targets will be good, but that may
not be the case, so this patch adds a check.

This patch also moves the unsol data out offset to the lib so the LLDs
do not have to track it.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-09-02 13:37:04 -05:00
James Bottomley
00dd7b7d26 Merge ../linux-2.6
Conflicts:

	arch/ia64/hp/sim/simscsi.c

Stylistic differences in two separate fixes for buffer->request_buffer
problem.

Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-08-06 12:42:33 -05:00
Or Gerlitz
8ddc7c5326 IB/ipoib: Remove broken link from Kconfig and documentation
Remove references to the IPoIB IETF working group as it has been closed.

Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-08-03 10:48:31 -07:00
Ishai Rabinovitz
559ce8f150 IB/srp: Work around data corruption bug on Mellanox targets
Data corruption has been seen with Mellanox SRP targets when FMRs
create a memory region with I/O virtual address != 0.  Add a
workaround that disables FMR merging for Mellanox targets (OUI 0002c9).

Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-08-03 10:35:43 -07:00
Ishai Rabinovitz
d916a8f1b4 IB/srp: Fix crash in srp_reconnect_target
Protect against srp_reset_device() clearing the req_queue while
srp_reconnect_target() is in progress (note that state change at
the top of srp_reconnect_target() is not sufficient for this since
srp_reset_device() ignores the state).

Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-08-03 09:44:22 -07:00
Mike Christie
1c83469d36 [SCSI] iscsi bugfixes: fix oops when iser is flushing io
When we enter recovery and flush the running commands
we cannot freee the connection before flushing the commands.
Some commands may have a reference to the connection
that needs to be released before. iscsi_stop was forcing
the term and suspend too early and was causing a oops
in iser, so this patch removes those callbacks all together
and allows the LLD to handle that detail.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-07-28 11:48:32 -05:00
Michael S. Tsirkin
8a7f752125 IB/ipoib: Fix packet loss after hardware address update
The neighbour ha field may get updated without destroying the
neighbour.  In this case, the ha field gets out of sync with the
address handle stored in ipoib_neigh->ah, with the result that
the ah field would point to an incorrect path, resulting in all
packets being lost.

Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-07-24 09:18:07 -07:00
Or Gerlitz
624d01f899 IB/ipoib: Fix oops with ipoib_debug_mcast set
Need to set mcast->ah before debug code dereferences it.

Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-07-24 09:18:07 -07:00
Michael S. Tsirkin
adfaa888a2 [PATCH] fmr pool: remove unnecessary pointer dereference
ib_fmr_pool_map_phys gets the virtual address by pointer but never writes
there, and users (e.g.  srp) seem to assume this and ignore the value
returned.  This patch cleans up the API to get the VA by value, and updates
all users.

Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Acked-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-14 21:53:51 -07:00
Vu Pham
6583eb3dcc [PATCH] srp: fix fmr error handling
srp_unmap_data assumes req->fmr is NULL if the request is not mapped, so we
must clean it out in case of an error.

Signed-off-by: Vu Pham <vu@mellanox.com>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-14 21:53:50 -07:00
James Bottomley
c4e00fac42 Merge ../scsi-misc-2.6
Conflicts:

	drivers/scsi/nsp32.c
	drivers/scsi/pcmcia/nsp_cs.c

Removal of randomness flag conflicts with SA_ -> IRQF_ global
replacement.

Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-07-03 09:41:12 -05:00
Linus Torvalds
22a3e233ca Merge git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
  Remove obsolete #include <linux/config.h>
  remove obsolete swsusp_encrypt
  arch/arm26/Kconfig typos
  Documentation/IPMI typos
  Kconfig: Typos in net/sched/Kconfig
  v9fs: do not include linux/version.h
  Documentation/DocBook/mtdnand.tmpl: typo fixes
  typo fixes: specfic -> specific
  typo fixes in Documentation/networking/pktgen.txt
  typo fixes: occuring -> occurring
  typo fixes: infomation -> information
  typo fixes: disadvantadge -> disadvantage
  typo fixes: aquire -> acquire
  typo fixes: mecanism -> mechanism
  typo fixes: bandwith -> bandwidth
  fix a typo in the RTC_CLASS help text
  smb is no longer maintained

Manually merged trivial conflict in arch/um/kernel/vmlinux.lds.S
2006-06-30 15:39:30 -07:00
Andrew Morton
cfa7b0d469 [PATCH] infiniband: devfs fix
Remove devfs leftovers.

Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-30 11:25:41 -07:00
Jörn Engel
6ab3d5624e Remove obsolete #include <linux/config.h>
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-06-30 19:25:36 +02:00
Mike Christie
358ff019b8 [SCSI] iscsi: convert iser to new set/get param fns
Convert iser to libiscsi get/set param functions.
Fix bugs in it returning old error return values and
have it expose exp_statsn.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-06-29 11:07:41 -04:00
Akinobu Mita
179e09172a [PATCH] drivers: use list_move()
This patch converts the combination of list_del(A) and list_add(A, B) to
list_move(A, B) under drivers/.

Acked-by: Corey Minyard <minyard@mvista.com>
Cc: Ben Collins <bcollins@debian.org>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Alasdair Kergon <dm-devel@redhat.com>
Cc: Gerd Knorr <kraxel@bytesex.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Frank Pavlic <fpavlic@de.ibm.com>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Cc: Andrew Vasquez <linux-driver@qlogic.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: Akinobu Mita <mita@miraclelinux.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:18 -07:00
Or Gerlitz
3f1244a2f8 IB/iser: iSER Kconfig and Makefile
Kconfig and Makefile for iSER.

Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-06-22 07:51:14 -07:00
Or Gerlitz
6461f64ab5 IB/iser: iSER handling of memory for RDMA
This file contains the processing carried over an SG list associated with
a SCSI command such that it can be registered with the IB verbs. The
registration produces a network virtual address (VA) and a remote access
key (RKEY or STAG in iSER spec notation) which are used by the target for
its RDMA operation.

Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-06-22 07:51:12 -07:00
Or Gerlitz
1cfa0a75db IB/iser: iSER RDMA CM (CMA) and IB verbs interaction
This file contains the low level interaction with the RDMA CM
and the IB verbs, where iSER is consumer of both.

Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-06-22 07:51:11 -07:00
Or Gerlitz
e85b24b5e7 IB/iser: iSER initiator iSCSI PDU and TX/RX
This file contains the iSER initiator processing of iSCSI PDUs - controls,
commands and data-outs along with processing of TX and RX completions.
It interacts with the lower level iser code doing the memory registration
and and the cma and verbs calls.

Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-06-22 07:51:09 -07:00
Or Gerlitz
65e7ae7bfc IB/iser: iSCSI iSER transport provider high level code
This file contains the code that registeres with the iscsi transport manager
and with the SCSI Mid Layer, where much of the provided functions to iSCSI and
SCSI are implemented in libiscsi.

Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-06-22 07:51:07 -07:00
Or Gerlitz
49cd5382f6 IB/iser: iSCSI iSER transport provider header file
iSER (iSCSI Extensions for RDMA) transport provider driver for the iSCSI
initiator, whose other parts (under drivers/scsi) are scsi_transport_iscsi
- the transport management module, iscsi_tcp - the TCP transport provider
module and libiscsi - a kernel library (module) implementing functionality
needed by both TCP and iSER transports. iSER is both a provider of the iSCSI
transport api and a SCSI low level driver.

This file contains internal data structures and non static service functions.

Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-06-22 07:51:05 -07:00
Linus Torvalds
4c84a39c8a Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (46 commits)
  IB/uverbs: Don't serialize with ib_uverbs_idr_mutex
  IB/mthca: Make all device methods truly reentrant
  IB/mthca: Fix memory leak on modify_qp error paths
  IB/uverbs: Factor out common idr code
  IB/uverbs: Don't decrement usecnt on error paths
  IB/uverbs: Release lock on error path
  IB/cm: Use address handle helpers
  IB/sa: Add ib_init_ah_from_path()
  IB: Add ib_init_ah_from_wc()
  IB/ucm: Get rid of duplicate P_Key parameter
  IB/srp: Factor out common request reset code
  IB/srp: Support SRP rev. 10 targets
  [SCSI] srp.h: Add I/O Class values
  IB/fmr: Use device's max_map_map_per_fmr attribute in FMR pool.
  IB/mthca: Fill in max_map_per_fmr device attribute
  IB/ipath: Add client reregister event generation
  IB/mthca: Add client reregister event generation
  IB: Move struct port_info from ipath to <rdma/ib_smi.h>
  IPoIB: Handle client reregister events
  IB: Add client reregister event type
  ...
2006-06-19 19:01:59 -07:00
Herbert Xu
932ff279a4 [NET]: Add netif_tx_lock
Various drivers use xmit_lock internally to synchronise with their
transmission routines.  They do so without setting xmit_lock_owner.
This is fine as long as netpoll is not in use.

With netpoll it is possible for deadlocks to occur if xmit_lock_owner
isn't set.  This is because if a printk occurs while xmit_lock is held
and xmit_lock_owner is not set can cause netpoll to attempt to take
xmit_lock recursively.

While it is possible to resolve this by getting netpoll to use
trylock, it is suboptimal because netpoll's sole objective is to
maximise the chance of getting the printk out on the wire.  So
delaying or dropping the message is to be avoided as much as possible.

So the only alternative is to always set xmit_lock_owner.  The
following patch does this by introducing the netif_tx_lock family of
functions that take care of setting/unsetting xmit_lock_owner.

I renamed xmit_lock to _xmit_lock to indicate that it should not be
used directly.  I didn't provide irq versions of the netif_tx_lock
functions since xmit_lock is meant to be a BH-disabling lock.

This is pretty much a straight text substitution except for a small
bug fix in winbond.  It currently uses
netif_stop_queue/spin_unlock_wait to stop transmission.  This is
unsafe as an IRQ can potentially wake up the queue.  So it is safer to
use netif_tx_disable.

The hamradio bits used spin_lock_irq but it is unnecessary as
xmit_lock must never be taken in an IRQ handler.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-06-17 21:30:14 -07:00
Ishai Rabinovitz
526b4caa0a IB/srp: Factor out common request reset code
Misc cleanups in ib_srp:
1) I think that it is more efficient to move the req entries from req_list
   to free_list in srp_reconnect_target (rather than rebuild the free_list).
   (In any case this code is shorter).
2) This allows us to reuse code in srp_reset_device and srp_reconnect_target
   and call a new function srp_reset_req.

Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-06-17 20:37:38 -07:00
Ramachandra K
0c0450db31 IB/srp: Support SRP rev. 10 targets
There has been a change in the format of port identifiers between
revision 10 of the SRP specification and the current revision 16A.

Revision 10 specifies port identifier format as

  lower 8 bytes :  GUID   upper 8 bytes :  Extension

Whereas revision 16A specifies it as 

 lower 8 bytes :  Extension  upper 8 bytes :  GUID

There are older targets (e.g. SilverStorm Virtual Fibre Channel
Bridge) which conform to revision 10 of the SRP specification.

The I/O class of revision 10 is 0xFF00 and the I/O class of revision
16A is 0x0100.

For supporting older targets, this patch:

1) Adds a new optional target creation parameter "io_class". Default
   value of io_class is 0x0100 (i.e. revision 16A)
2) Uses the correct port identifier format for targets with IO class
   of 0xFF00 (i.e. conforming to revision 10)

Signed-off-by: Ramachandra K <rkuchimanchi@silverstorm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-06-17 20:37:38 -07:00
Leonid Arsh
508e434123 IPoIB: Handle client reregister events
Handle client reregister events by treating them just like LID or
SM changes -- flush all cached paths and rejoin multicast groups.

Signed-off-by: Leonid Arsh <leonida@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-06-17 20:37:36 -07:00
Jack Morgenstein
37c22a7721 IPoIB: Fix kernel unaligned access on ia64
Fix misaligned access faults on ia64: never cast a misaligned
neighbour->ha + 4 pointer to union ib_gid type; pass a void * pointer
instead.  The memcpy was being optimized to use full word accesses
because the compiler thought that union ib_gid is always aligned.

The cast in IPOIB_GID_ARG is safe, since it is fixed to access each
byte separately.

Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-06-17 20:37:35 -07:00
Roland Dreier
31c02e2157 IPoIB: Avoid using stale last_send counter when reaping AHs
The comparisons of priv->tx_tail to ah->last_send in ipoib_free_ah()
and ipoib_post_receive() are slightly unsafe, because priv->tx_lock is
not held and hence a stale value of ah->last_send might be used, which
would lead to freeing an AH before the driver was really done with it.
The simple way to fix this is to the optimization of early free from
ipoib_free_ah() and unconditionally queue AHs for reaping, and then
take priv->tx_lock in __ipoib_reap_ah().

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-06-17 20:37:34 -07:00
Roland Dreier
6bfa24fa3e IB/srp: Get rid of "Target has req_lim 0" messages
It's perfectly valid for a connection to an SRP target to have a
request limit of 0, so get rid of the message about it, which can spam
kernel logs even with printk_ratelimit().  Keep a count of such events
in a "zero_req_lim" SCSI host attribute instead, so someone who cares
can look at the statistics.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-06-17 20:37:33 -07:00
Ishai Rabinovitz
b7ac4ab497 IB/srp: Handle DREQ events from CM
Handle IB_CM_DREQ_ERROR and IB_CM_DREQ_RECEIVED events from the CM,
instead of just printing "Unhandled CM event".  In the case of
DREQ_ERROR, just ignore the event -- a TIMEWAIT_EXIT will be generated
also.  For DREQ_RECEIVED, send a DREP in response to shut the
connection down cleanly.

Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-06-17 20:37:32 -07:00
Vu Pham
74b0a15b5e IB/srp: Allow sg_tablesize to be adjusted
Make the sg_tablesize used by SRP adjustable at module load time via a
module parameter.  Calculate the corresponding IU length required to
support this.

Signed-off-by: Vu Pham <vu@mellanox.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-06-17 20:37:32 -07:00
Vu Pham
52fb2b50c4 IB/srp: Allow cmd_per_lun to be set per target port
Allow userspace to throttle traffic on a given connection to a target
port by adding "max_cmd_per_lun=xyz" to lower the cmd_per_lun value
set for that scsi_host.

Signed-off-by: Vu Pham <vu@mellanox.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-06-17 20:37:31 -07:00
Ishai Rabinovitz
0c5b395239 IB/srp: Clean up loop in srp_remove_one()
Interrupts will always be enabled in srp_remove_one(), so
spin_lock_irq() can be used instead of spin_lock_irqsave().
Also, the loop takes target->scsi_host->host_lock, so target->state
can just be set to SRP_TARGET_REMOVED witout testing the old value.

Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-06-17 20:37:31 -07:00
Matthew Wilcox
b3589fd490 IB/srp: Change target_mutex to a spinlock
The SRP driver never sleeps while holding target_mutex, and it's just
used to protect some simple list operations, so hold times will be
short.  So just convert it to a spinlock, which is smaller and faster.

Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-06-17 20:37:30 -07:00
Matthew Wilcox
549c5fc2c8 IB/srp: Get rid of unneeded use of list_for_each_entry_safe()
list_for_each_entry_safe() is used in one place where the list isn't
modified.  So just change it to list_for_each_entry().

Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-06-17 20:37:30 -07:00
Matthew Wilcox
1962a4a1e4 IB/srp: Use SCAN_WILD_CARD from SCSI headers
SCAN_WILD_CARD is indeed available from <scsi/scsi.h>, which is
already included.  So get rid of private hack.

Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-06-17 20:37:30 -07:00
Roland Dreier
f5358a172f IB/srp: Use FMRs to map gather/scatter lists
Create an SRP FMR pool on HCAs that support FMRs, and use FMRs to map
gather/scatter lists that have more than one entry into a single
memory region that appears virtually contiguous to the SRP target
(which is the RDMA initiator).

This patch bails out on FMR mapping for SCSI commands where the
gather/scatter list cannot be mapped into a single FMR because there
are sub-page-sized entries in middle of the list.  An unaligned
start or end of the list is OK.

Based on a patch by Vu Pham <vuhuong@mellanox.com>.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-06-17 20:37:29 -07:00
Eli Cohen
959eb39297 IPoIB: Fix AH leak at interface down
When ipoib_stop() is called it first calls netif_stop_queue() to stop
the kernel from passing more packets to the network driver. However,
the completion handler may call netif_wake_queue() re-enabling packet
transfer.

This might result in leaks (we see AH leaks which we think can be
attributed to this bug) as new packets get posted while the interface
is going down.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Michael Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-06-05 09:51:36 -07:00
Ishai Rabinovitz
093beac189 IB/srp: Complete correct SCSI commands on device reset
When flushing out queued commands after a successful device reset,
make sure that SRP completes the right commands, instead of calling
scsi_done on the command passed into the device reset handler over and
over.

Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-05-17 09:20:48 -07:00
Roland Dreier
ec2d720849 IB/srp: Get rid of extra scsi_host_put()s if reconnection fails
If a reconnection attempt fails, then SRP does two scsi_host_put()s.
This is a historical relic from an earlier version of the driver that
took a reference on the scsi_host before trying to reconnect, so get
rid of the extra scsi_host_put().

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-05-17 09:16:03 -07:00
Roland Dreier
e65810566f IB/srp: Don't wait for disconnection if sending DREQ fails
Sending a DREQ may fail, for example because the remote target has
already broken the connection.  If so, then SRP should not wait for
the disconnection to complete, because it never will.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-05-17 09:13:21 -07:00
Roland Dreier
5941d079f2 IPoIB: Free child interfaces properly
When deleting a child interface with a non-default P_Key via
/sys/class/net/ibX/delete_child, the interface must be freed with
free_netdev() (rather than kfree() on the private data).

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-05-09 22:54:59 -07:00
Roland Dreier
d945e1df28 IB/srp: Fix tracking of pending requests during error handling
If a SCSI abort completes, or the command completes successfully, then
the driver must remove the command from its queue of pending
commands.  Similarly, if a device reset succeeds, then all commands
queued for the given device must be removed from the queue.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-05-09 10:50:28 -07:00
Roland Dreier
f80887d0b9 IB/srp: Remove request from list when SCSI abort succeeds
If a SCSI abort succeeds, then the aborted request should to be
removed from the list of pending requests.  This fixes list corruption
after an abort occurs.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-04-19 11:40:10 -07:00
Roland Dreier
f697f74a6b IPoIB: Use spin_lock_irq() instead of spin_lock_irqsave()
We know ipoib_flush_paths() is called from plain process context with
interrupts enabled, since it does wait_for_completion().  So there's
no need to use spin_lock_irqsave() -- spin_lock_irq() is fine.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-04-10 09:43:59 -07:00
Eli Cohen
a30bb96c6f IPoIB: Close race in ipoib_flush_paths()
ib_sa_cancel_query() must be called with priv->lock held since
a completion might arrive and set path->query to NULL.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-04-10 09:43:59 -07:00
Shirley Ma
0f4852513f IPoIB: Make send and receive queue sizes tunable
Make IPoIB's send and receive queue sizes tunable via module
parameters ("send_queue_size" and "recv_queue_size").  This allows the
queue sizes to be enlarged to fix disastrously bad performance on some
platforms and workloads, without bloating memory usage when large
queues aren't needed.

Signed-off-by: Shirley Ma <xma@us.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-04-10 09:43:58 -07:00
Eli Cohen
f2de3b0612 IPoIB: Wait for join to finish before freeing mcast struct
ipoib_mcast_restart_task() might free an mcast object while a join
request is still outstanding, leading to an oops when the query
completes.  Fix this by waiting for query to complete, similar to what
ipoib_stop_thread() is doing.  The wait for mcast completion code is
consolidated in wait_for_mcast_join().

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-04-10 09:43:58 -07:00
Jack Morgenstein
bf6a9e31cf IB: simplify static rate encoding
Push translation of static rate to HCA format into low-level drivers,
where it belongs.  For static rate encoding, use encoding of rate
field from IB standard PathRecord, with addition of value 0, for
backwards compatibility with current usage.  The changes are:

 - Add enum ib_rate to midlayer includes.
 - Get rid of static rate translation in IPoIB; just use static rate
   directly from Path and MulticastGroup records.
 - Update mthca driver to translate absolute static rate into the
   format used by hardware.  This also fixes mthca's static rate
   handling for HCAs that are capable of 4X DDR.

Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-04-10 09:43:47 -07:00
Michael S. Tsirkin
d2e0655ede IPoIB: Consolidate private neighbour data handling
Consolidate IPoIB's private neighbour data handling into
ipoib_neigh_alloc() and ipoib_neigh_free().  This will make it easier
to keep track of the neighbour structures that IPoIB is handling, and
is a nice cleanup of the code:

add/remove: 2/1 grow/shrink: 1/8 up/down: 100/-178 (-78)
function                                     old     new   delta
ipoib_neigh_alloc                              -      61     +61
ipoib_neigh_free                               -      36     +36
ipoib_mcast_join_finish                     1288    1291      +3
path_rec_completion                          575     573      -2
ipoib_mcast_join_task                        664     660      -4
ipoib_neigh_destructor                       101      92      -9
ipoib_neigh_setup_dev                         14       3     -11
ipoib_neigh_setup                             17       -     -17
path_free                                    238     215     -23
ipoib_mcast_free                             329     306     -23
ipoib_mcast_send                             718     684     -34
neigh_add_path                               705     650     -55

Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-04-04 14:46:48 -07:00
Roland Dreier
ce1823f032 IB/srp: Fix memory leak in options parsing
Fix memory leak if parsing destination GID fails.

Coverity bug 1042

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-04-03 09:31:04 -07:00
Roland Dreier
f5545d24b8 IPoIB: Always build debugging code unless CONFIG_EMBEDDED=y
Don't allow CONFIG_INFINIBAND_IPOIB_DEBUG to be disabled unless
CONFIG_EMBEDDED is selected.  We want users (and especially distros)
to have this turned on unless they really need to save space, because
by the time we want debugging output, it's usually too late to rebuild
a kernel.  The debugging output can be controlled at runtime via the
debug_level module parameter in sysfs.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-04-02 14:39:19 -07:00
Roland Dreier
ef12d45619 IPoIB: Fix oops with raw sockets
ipoib_hard_header() needs to handle the case that daddr is NULL.  This
can happen when packets are injected via a raw socket, and IPoIB
shouldn't oops in this case.

Reported by Anton Blanchard <anton@samba.org>

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-03-29 09:36:46 -08:00
Roland Dreier
3f89f83449 IB/srp: Fix unmapping of fake scatterlist
The recently merged patch to create a fake scatterlist for non-SG SCSI
commands had a bug: the driver ended up doing dma_unmap_sg() on a
scatterlist scmnd->request_buffer rather than the fake scatter list it
created.  Fix this so that the driver unmaps the same thing it maps.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-03-29 09:36:45 -08:00
Leonid Arsh
7a343d4c46 IPoIB: P_Key change event handling
This patch causes the network interface to respond to P_Key change
events correctly.  As a result, you'll see a child interface in the
"RUNNING" state (netif_carrier_on()) only when the corresponding P_Key
is configured by the SM.  When SM removes a P_Key, the "RUNNING" state
will be disabled for the corresponding network interface.  To
implement this, I added IB_EVENT_PKEY_CHANGE event handling.  To
prevent flushing the device before the device is open by the "delay
open" mechanism, I added an additional device flag called
IPOIB_FLAG_INITIALIZED.

This also prevents the child network interface from trying to join to
multicast groups until the PKEY is configured.  We used to get error
messages like:

    ib0.f2f2: couldn't attach QP to multicast group ff12:401b:f2f2:0:0:0:ffff:ffff

in this case.  To fix this, I just check IPOIB_FLAG_OPER_UP flag in
ipoib_set_mcast_list().

Signed-off-by: Leonid Arsh <leonida@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-03-24 15:47:30 -08:00
Leonid Arsh
4e37b95616 IPoIB: Fix network interface "RUNNING" status
With the current IPoIB driver, the status of network interfaces stays
"RUNNING" even if the link goes down (for example because a cable is
unplugged).  Fix this by flushing the IPoIB interface when the link
goes down.

Signed-off-by: Leonid Arsh <leonida@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-03-24 15:47:29 -08:00
Roland Dreier
cf368713a3 IB/srp: Use a fake scatterlist for non-SG SCSI commands
Since the SCSI midlayer is moving towards entirely getting rid of
commands with use_sg == 0, we should treat this case as an exception.
Therefore, change the IB SRP initiator to create a fake scatterlist
for these commands with sg_init_one().  This simplifies the flow of
DMA mapping and unmapping, since SRP can just use dma_map_sg() and
dma_unmap_sg() unconditionally, rather than having to choose between
the dma_{map,unmap}_sg() and dma_{map,unmap}_single() variants.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-03-24 15:47:26 -08:00
Leonid Arsh
6f633c8d69 IPoIB: Pass correct pointer when flushing child interfaces
ipoib_ib_dev_flush() should get passed cpriv->dev, not &cpriv->dev.

Signed-off-by: Leonid Arsh <leonida@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-03-24 15:47:25 -08:00
Linus Torvalds
3d1f337b3e Merge master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (235 commits)
  [NETFILTER]: Add H.323 conntrack/NAT helper
  [TG3]: Don't mark tg3_test_registers() as returning const.
  [IPV6]: Cleanups for net/ipv6/addrconf.c (kzalloc, early exit) v2
  [IPV6]: Nearly complete kzalloc cleanup for net/ipv6
  [IPV6]: Cleanup of net/ipv6/reassambly.c
  [BRIDGE]: Remove duplicate const from is_link_local() argument type.
  [DECNET]: net/decnet/dn_route.c: fix inconsequent NULL checking
  [TG3]: make drivers/net/tg3.c:tg3_request_irq() static
  [BRIDGE]: use LLC to send STP
  [LLC]: llc_mac_hdr_init const arguments
  [BRIDGE]: allow show/store of group multicast address
  [BRIDGE]: use llc for receiving STP packets
  [BRIDGE]: stp timer to jiffies cleanup
  [BRIDGE]: forwarding remove unneeded preempt and bh diasables
  [BRIDGE]: netfilter inline cleanup
  [BRIDGE]: netfilter VLAN macro cleanup
  [BRIDGE]: netfilter dont use __constant_htons
  [BRIDGE]: netfilter whitespace
  [BRIDGE]: optimize frame pass up
  [BRIDGE]: use kzalloc
  ...
2006-03-21 09:31:48 -08:00
Arnaldo Carvalho de Melo
e35fc38565 [INFINIBAND] ipoib: Remove leftover use of neigh_ops->destructor
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-03-20 22:46:40 -08:00
Michael S. Tsirkin
c5ecd62c25 [NET]: Move destructor from neigh->ops to neigh_params
struct neigh_ops currently has a destructor field, which no in-kernel
drivers outside of infiniband use.  The infiniband/ulp/ipoib in-tree
driver stashes some info in the neighbour structure (the results of
the second-stage lookup from ARP results to real link-level path), and
it uses neigh->ops->destructor to get a callback so it can clean up
this extra info when a neighbour is freed.  We've run into problems
with this: since the destructor is in an ops field that is shared
between neighbours that may belong to different net devices, there's
no way to set/clear it safely.

The following patch moves this field to neigh_parms where it can be
safely set, together with its twin neigh_setup.  Two additional
patches in the patch series update ipoib to use this new interface.

Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-03-20 22:25:41 -08:00
Roland Dreier
bfef73fa78 IPoIB: Get rid of useless test of queue length
In neigh_add_path(), the queue of delayed packets can never be full,
because the queue is always freshly created and cannot be found by any
other code path.  In fact, the test of the queue length is worse than
useless: if somehow the test ever triggered and path_rec_start() also
failed, then dev_kfree_skb_any() will be called twice on the same skb.
Fix this by deleting the useless test.  Pointed out by Michael
S. Tsirkin <mst@mellanox.co.il>.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-03-20 10:08:26 -08:00
Roland Dreier
bf17c1c7cc IB/srp: Coverity fix to srp_parse_options()
Fix leak found by Coverity: in the SRP_OPT_DGID case,
srp_parse_options() didn't free the result of match_strdup().

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-03-20 10:08:25 -08:00
Jack Morgenstein
0b3ea0829c IPoIB: Move ipoib_ib_dev_flush() to ipoib workqueue
Move ipoib_ib_dev_flush() to ipoib's workqueue.  This keeps it ordered
with respect to other work scheduled by the ipoib driver.  This fixes
problems with races, for example:
 - ipoib_ib_dev_flush() has started running because of an IB event
 - user does ifconfig ib0 down
 - ipoib_mcast_stop_thread() gets called twice and waits for the same
   completion twice

Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-03-20 10:08:24 -08:00
Roland Dreier
8b9ab02b69 IPoIB: Fix build now that neighbour destructor is in neigh_params
Fix the IPoIB build (which is broken in net-2.6.17 because of my
screw-up, which left out this chunk in ipoib_multicast.c). 
The neighbour destructor is now in neigh_params, so we don't
need to clear it in the ops structure.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-03-20 10:08:24 -08:00
Roland Dreier
6ecb0c8496 IB/srp: Add SCSI host attributes to show target port
Add SCSI host attributes in sysfs that show the ID extension, IOC
GUID, service ID, P_Key and destination GID for each target port that
the SRP initiator connects to.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-03-20 10:08:23 -08:00
Michael S. Tsirkin
9acf6a8570 IPoIB: Fix multicast race between canceling and completing
ipoib_mcast_stop_thread currently tests mcast->query and if it is
NULL, does not perform wait_for_completion on the mcast and frees the
mcast object directly.

However, since both operations are done without locking, it is
possible that ipoib_mcast_join_complete is in progress on this mcast
object and has set mcast->query to NULL already.

Solve this by:
- taking priv->lock before we change mcast->query in ipoib_mcast_join_complete,
  and keeping it until we no longer need the mcast object
- taking priv->lock around mcast->query test in ipoib_mcast_stop_thread

Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-03-20 10:08:20 -08:00
Eli Cohen
54d07e2a1e IPoIB: Clean up if posting receives fails
If posting receives in ipoib_ib_dev_open() fails, call
ipoib_ib_dev_stop() to move the device's QP back to the RESET state so
that we can try again later.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-03-20 10:08:19 -08:00
Eli Cohen
7343b231f2 IPoIB: Close race in setting mcast->ah
ipoib_mcast_send() tests mcast->ah twice.  If this value is changed
between these two points, we leak an skb.  However,
ipoib_mcast_join_finish() sets mcast->ah with no locking, so it could
race against ipoib_mcast_send().

As a solution, take priv->lock around assignment to mcast->ah thus
making sure ipoib_mcast_send() (which also takes priv->lock) is not in
flight.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-03-20 10:08:18 -08:00
Michael S. Tsirkin
44af79f952 IPoIB: clarify to_ipoib_neigh()
Cosmetic change: make alignment explicit in to_ipoib_neigh.

Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-03-20 10:08:16 -08:00
Roland Dreier
1285b3a0b0 IB/srp: Don't send task management commands after target removal
Just fail abort and reset requests that come in after we've already
decided to remove a target.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-03-03 17:50:16 -08:00
Roland Dreier
20b83382d1 IPoIB: Yet another fix for send-only joins
Even after the last fix, it's still possible for a send-only join to
start before the join for the broadcast group has finished.  This
could cause us to create a multicast group using attributes from the
broadcast group that haven't been initialized yet, so we would use
garbage for the Q_Key, etc.  Fix this by waiting until the broadcast
group's attached flag is set before starting send-only joins.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-02-11 12:22:12 -08:00
Michael S. Tsirkin
7bcb974ef6 IPoIB: Fix another send-only join race
Further, there's an additional issue that I saw in testing:
ipoib_mcast_send may get called when priv->broadcast is NULL (e.g. if
the device was downed and then upped internally because of a port
event).

If this happends and the send-only join request gets completed before
priv->broadcast is set, we get an oops.

Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-02-07 16:39:26 -08:00
Michael S. Tsirkin
479a079663 IPoIB: Don't start send-only joins while multicast thread is stopped
Fix the following race scenario:
  - Device is up.
  - Port event or set mcast list triggers ipoib_mcast_stop_thread,
    this cancels the query and waits on mcast "done" completion.
  - Completion is called and "done" is set.
  - Meanwhile, ipoib_mcast_send arrives and starts a new query,
    re-initializing "done".

Fix this by adding a "multicast started" bit and checking it before
starting a send-only join.

Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-02-07 16:37:08 -08:00
Ingo Molnar
8e9e5f4f5e IB/srp: Semaphore to mutex conversion
Convert srp_host->target_mutex from a semaphore to a mutex.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-01-30 15:21:21 -08:00
Michael S. Tsirkin
b36f170b61 IPoIB: Lock accesses to multicast packet queues
Avoid corrupting mcast->pkt_queue by serializing access with
priv->tx_lock.  Also, update dropped packet statistics to count
multicast packets removed from pkt_queue as dropped.

Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-01-17 12:19:40 -08:00
Michael S. Tsirkin
47f7a0714b IPoIB: Make sure path is fully initialized before using it
The SA path record query completion can initialize path->pathrec.dlid
before IPoIB's callback runs and initializes path->ah, so we must test
ah rather than dlid.

Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-01-17 09:22:05 -08:00
Ingo Molnar
95ed644fd1 IB: convert from semaphores to mutexes
semaphore to mutex conversion by Ingo and Arjan's script.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
[ Sanity-checked on real IB hardware ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-01-13 14:51:39 -08:00
Eli Cohen
988bd50300 IPoIB: Fix memory leak of multicast group structures
The current handling of multicast groups in IPoIB ends up never
freeing send-only multicast groups.  It turns out the logic was much
more complicated than it needed to be; we can fix this bug and
completely kill ipoib_mcast_dev_down() at the same time.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-01-12 14:32:20 -08:00
Michael S. Tsirkin
78bfe0b5b6 IPoIB: Take dev->xmit_lock around mc_list accesses
dev->mc_list accesses must be protected by dev->xmit_lock.
Found by Eli Cohen <eli@mellanox.co.il>.

Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-01-11 11:47:34 -08:00
Eli Cohen
97460df37e IPoIB: Fix address handle refcounting for multicast groups
Multiple ipoib_neigh structures on mcast->neigh_list may point to the
same ah.  This means that ipoib_mcast_free() can't just make a list of
ah structs to free, since this might end up trying to add the same ah
to the list more than once.  Handle this in ipoib_multicast.c in the
same way as it is handled in ipoib_main.c for struct ipoib_path.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-01-10 07:43:02 -08:00
Eli Cohen
70b4c8cdc1 IPoIB: Fix error path in ipoib_mcast_dev_flush()
Don't leak memory on allocation failure for broadcast mcast group.
Also, print a warning to match handling for other mcast groups.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-01-10 07:42:14 -08:00
Sean Hefty
cf311cd49a IB: Add node_guid to struct ib_device
Add a node_guid field to struct ib_device.  It is the responsibility
of the low-level driver to initialize this field before registering a
device with the midlayer.  Convert everyone to looking at this field
instead of calling ib_query_device() when all they want is the node
GUID, and remove the node_guid field from struct ib_device_attr.

Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2006-01-10 07:39:34 -08:00
Tim Schmielau
de25968cc8 [PATCH] fix more missing includes
Include fixes for 2.6.14-git11.  Should allow to remove sched.h from
module.h on i386, x86_64, arm, ia64, ppc, ppc64, and s390.  Probably more
to come since I haven't yet checked the other archs.

Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-08 20:13:45 -08:00
Arnaldo Carvalho de Melo
14c850212e [INET_SOCK]: Move struct inet_sock & helper functions to net/inet_sock.h
To help in reducing the number of include dependencies, several files were
touched as they were getting needed headers indirectly for stuff they use.

Thanks also to Alan Menegotto for pointing out that net/dccp/proto.c had
linux/dccp.h include twice.

Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-01-03 13:11:21 -08:00
Roland Dreier
267ee88ed3 IPoIB: fix error handling in ipoib_open
If ipoib_ib_dev_up() fails after ipoib_ib_dev_open() is called, then
ipoib_ib_dev_stop() needs to be called to clean up.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-11-29 10:55:58 -08:00
Michael S. Tsirkin
4f71055a45 IPoIB: protect child list in ipoib_ib_dev_flush
race condition: ipoib_ib_dev_flush is accessing child list without locks.

Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-11-29 10:53:30 -08:00
Roland Dreier
2e86541ec8 IPoIB: don't zero members after we allocate with kzalloc
ipoib_mcast_alloc() uses kzalloc(), so there's no need to zero out
members of the mcast struct after it's allocated.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-11-29 10:25:23 -08:00
Michael S. Tsirkin
de92248789 IPoIB: reinitialize mcast structs' completions for every query
Make sure mcast->done is initialized to uncompleted value before we
submit a new query, so that it's safe to wait on.

Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-11-29 10:18:45 -08:00
Roland Dreier
5872a9fc28 IPoIB: always set path->query to NULL when query finishes
Always set path->query to NULL when the SA path record query
completes, rather than only when we don't have an address handle.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-11-29 10:13:54 -08:00
Roland Dreier
65c7eddaba IPoIB: reinitialize path struct's completion for every query
It's possible that IPoIB will issue multiple SA queries for the same
path struct.  Therefore the struct's completion needs to be
initialized for each query rather than only once when the struct is
allocated, or else we might not wait long enough for later queries to
finish and free the path struct too soon.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-11-28 21:20:34 -08:00
Roland Dreier
47f2bce902 [IB] srp: don't post receive if no send buf available
Have __srp_get_tx_iu() fail if the target port's request limit will
not allow the initiator to post a send.  This avoids continuing on and
posting a receive, and then failing to post a corresponding send.  If
that happens, then the initiator will end up with an extra receive
posted, and if this happens to much, the receive queue will overflow.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-11-15 00:19:21 -08:00
Roland Dreier
5f068992a1 [IB] srp: increase max_luns
Increase SRP max_luns to 512 to match the kernel's default, since SRP
storage targets can have lots of LUNs and the SRP initiator itself
doesn't have any particular limit.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-11-11 14:06:01 -08:00
Linus Torvalds
78b9c0f91c Merge branch 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband 2005-11-10 13:27:06 -08:00
Roland Dreier
8c608a32e3 [IPoIB] no need to set skb->dev right before freeing skb
For cut-and-paste reasons, the IPoIB driver was setting skb->dev right
before calling dev_kfree_skb_any().  Get rid of this.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-11-10 10:22:50 -08:00
Roland Dreier
1732b0ef3b [IPoIB] add path record information in debugfs
Add ibX_path files to debugfs that contain information about the IPoIB
path cache.  IPoIB ARP only gives GIDs, which the IPoIB driver must
resolve to real IB paths through the ib_sa module.  For debugging,
when the ARP table looks OK but traffic isn't flowing, it's useful to
be able to see if the resolution from GID to path worked.

Also clean up the formatting of the existing _mcg debugfs files.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-11-10 10:22:49 -08:00
Olaf Hering
733482e445 [PATCH] changing CONFIG_LOCALVERSION rebuilds too much, for no good reason
This patch removes almost all inclusions of linux/version.h.  The 3
#defines are unused in most of the touched files.

A few drivers use the simple KERNEL_VERSION(a,b,c) macro, which is
unfortunatly in linux/version.h.

There are also lots of #ifdef for long obsolete kernels, this was not
touched.  In a few places, the linux/version.h include was move to where
the LINUX_VERSION_CODE was used.

quilt vi `find * -type f -name "*.[ch]"|xargs grep -El '(UTS_RELEASE|LINUX_VERSION_CODE|KERNEL_VERSION|linux/version.h)'|grep -Ev '(/(boot|coda|drm)/|~$)'`

search pattern:
/UTS_RELEASE\|LINUX_VERSION_CODE\|KERNEL_VERSION\|linux\/\(utsname\|version\).h

Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-11-09 07:55:57 -08:00
Linus Torvalds
127f2fa31a Merge branch 'srp' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband 2005-11-04 16:32:36 -08:00
Roland Dreier
8ae5a8a24f [IPoIB] don't compile debug code if debugging isn't enabled
Don't build ipoib_mcast_iter_ functions if CONFIG_INFINIBAND_IPOIB_DEBUG
is not enabled -- their only callers will not be built either.

Also move the prototype for ipoib_open() to ipoib.h to fix a sparse warning.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-11-02 20:51:01 -08:00
Roland Dreier
aef9ec39c4 IB: Add SCSI RDMA Protocol (SRP) initiator
Add an InfiniBand SCSI RDMA Protocol (SRP) initiator.  This driver is
used to talk talk to InfiniBand SRP targets (storage devices).

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-11-02 14:07:13 -08:00
Roland Dreier
21a384897d [IPoIB] remove unneeded initializations to 0
Shrink our source and .text a little by removing a few assignments of
NULL and 0 to memory that is already cleared as part of the allocation.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-11-02 10:07:59 -08:00
Roland Dreier
de6eb66b56 [IB] kzalloc() conversions
Replace kmalloc()+memset(,0,) with kzalloc(), for a net savings of 35
source lines and about 500 bytes of text.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-11-02 07:23:14 -08:00
Roland Dreier
3bc12e75b2 [IPoIB] cleanups: fix comment, remove useless variables
Minor cleanups: fix a misleading comment, and get rid of attr_mask
variables that are only used to hold constants (just use the constants
directly).

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-10-31 07:10:33 -08:00
Roland Dreier
a20583a7c2 [IPoIB] use spin_trylock_irqsave()
Use spin_trylock_irqsave() in ipoib_start_xmit() instead of
reinventing it out of local_irq_save(), spin_trylock() and
local_irq_restore().

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-10-29 13:54:40 -07:00
Roland Dreier
1993d683f3 [IPoIB] Drop RX packets when out of memory
Change the way IPoIB handles RX packets when it can't allocate a new
receive skbuff.  If the allocation of a new receive skb fails, we now
drop the packet we just received and repost the original receive skb.
This means that the receive ring always stays full and we don't have
to monkey around with trying to schedule a refill task for later.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-10-28 15:30:34 -07:00
Roland Dreier
4b2d319b53 [IPoIB] Improve ipoib_timeout() output
Use jiffies_to_msecs() so we print a human-readable time so
we don't have to worry about what HZ is configured to, and
print out a few values to make post-mortem analysis easier.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-10-18 12:20:06 -07:00
Roland Dreier
5b6810e048 [IPoIB] Rename ipoib_create_qp() -> ipoib_init_qp() and fix error cleanup
ipoib_create_qp() no longer creates IPoIB's QP, so it shouldn't
destroy the QP on failure -- that unwinding happens elsewhere, so the
current code can cause a double free.  While we're at it, the
function's name should match what it actually does, so rename it to
ipoib_init_qp().

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-10-17 15:20:29 -07:00
Roland Dreier
d70ed6075f [IPoIB] Rename IPoIB's path_lookup() to avoid name clashes
Rename IPoIB driver's path_lookup() to ipoib_path_lookup() to avoid a
clashes with the kernel global path_lookup().  We don't hit this with
the current kernel source, but some external patches seem to trigger
this, and it's cleaner to avoid clashing with global names anyway.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
refs/heads/for-linus
2005-09-28 19:56:57 -07:00
Roland Dreier
8d2cae0651 [PATCH] IPoIB: Don't flush workqueue from within workqueue
ipoib_mcast_restart_task() is always called from within the
single-threaded IPoIB workqueue, so flushing the workqueue from within
the function can lead to a recursion overflow.  But since we're
running in a single-threaded workqueue, we're already synchronized
against other items in the workqueue, so just get rid of the flush in
ipoib_mcast_restart_task().

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-09-20 10:52:04 -07:00
Hal Rosenstock
ce5b65cc96 [PATCH] IPoIB: Fix SA client retransmission strategy
We got a little mixed up with what the backoff member holds in the
IPoIB multicast group structure: sometimes it was used as a number of
seconds, and sometimes it was used as a number of jiffies.  Fix the
code so that backoff is always in seconds.

Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-09-18 22:02:38 -07:00
Michael S. Tsirkin
51574e0398 [PATCH] IPoIB: fix module removal race
Since ipoib uses queue_delayed_work to run flush task on port state events,
it must flush scheduled work after unregistering the event handler.

Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-09-18 22:02:37 -07:00
Michael S. Tsirkin
06c56e44f3 [PATCH] IPoIB: fix memory leak
Fix IPoIB memory leak on device removal.

Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-09-07 09:48:52 -07:00
Roland Dreier
a4d61e8480 [PATCH] IB: move include files to include/rdma
Move the InfiniBand headers from drivers/infiniband/include to include/rdma.
This allows InfiniBand-using code to live elsewhere, and lets us remove the
ugly EXTRA_CFLAGS include path from the InfiniBand Makefiles.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-08-26 20:37:38 -07:00
Michael S. Tsirkin
1ad62a19f1 [PATCH] IPoIB: Fix device removal race
Currently we may have work scheduled in default kernel workqueue when
the device is going down.  The device could get freed before this
workqueue gets serviced.  I am actually seeing this causing system
hangs.

The following patch fixes this by using ipoib_workqueue which gets
flushed when the device is going down.

Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-08-26 20:37:38 -07:00
Roland Dreier
4ce059378c [PATCH] IPoIB: Set full membership bit in P_Keys
Always make sure that the full membership bit is set in the P_Keys
that IPoIB uses.  This makes sure that all hosts join the correct
multicast groups so that hosts that are partial partition members
can talk to the rest of the network.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-08-26 20:37:37 -07:00
Olaf Hering
2aeba9a03b [PATCH] IB: Remove unnecessary includes of <linux/version.h>
changing CONFIG_LOCALVERSION rebuilds too much, for no appearent reason.
Remove unneeded includes of <linux/version.h>.

Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-08-26 20:37:36 -07:00
Sean Hefty
97f52eb438 [PATCH] IB: sparse endianness cleanup
Fix sparse warnings.  Use __be* where appropriate.

Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-08-26 20:37:35 -07:00
Hal Rosenstock
92a6b34bf4 [PATCH] IB: Eliminate redundant NULL checks
IPoIB: Eliminate NULL checks prior to calling kfree

Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-08-26 20:37:35 -07:00
Roland Dreier
2a1d9b7f09 [PATCH] IB: Add copyright notices
Make some lawyers happy and add copyright notices for people who
forgot to include them when they actually touched the code.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-08-26 20:37:35 -07:00
Hal Rosenstock
0dca0f7bf8 [PATCH] [IPoIB] Handle sending of unicast RARP responses
RARP replies are another valid case where IPoIB may need to send a
unicast packet with no neighbour structure.

Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-07-28 13:17:26 -07:00
Roland Dreier
2181858bb8 [IB/ipoib]: Fix unsigned comparisons to handle wraparound
Fix handling of tx_head/tx_tail comparisons to handle wraparound.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2005-07-27 14:41:32 -07:00
Roland Dreier
9adec1a808 [PATCH] IPoIB: convert to debugfs
Convert IPoIB to use debugfs instead of its own custom debugging filesystem.

Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-04-16 15:26:07 -07:00
Roland Dreier
e6ded99cbb [PATCH] IPoIB: fix static rate calculation
Correct and simplify calculation of static rate.  We need to round up the
quotient of (local_rate - path_rate) / path_rate.  To round up we add
(path_rate - 1) to the numerator, so the quotient simplifies to (local_rate -
1) / path_rate.

No idea how I came up with the old formula.

Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-04-16 15:26:06 -07:00
Hal Rosenstock
62241eb497 [PATCH] IPoIB: set skb->mac.raw on receive
Set skb->mac.raw on receive.  This fixes crashes when this is
dereferenced, for example by netfilter or when PF_PACKET is used.

Signed-off-by: Hal Rosenstock <halr@voltaire.com>
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-04-16 15:26:05 -07:00
Linus Torvalds
1da177e4c3 Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
2005-04-16 15:20:36 -07:00