Since commit 8dfd0374be ("MMC core: limit
minimum initialization frequency to 400kHz") MMC core checks for minimum
frequency, and that causes following messages flood when using eSDHC
controllers:
...
mmc0: Minimum clock frequency too high for identification mode
mmc0: Minimum clock frequency too high for identification mode
...
The warnings are legitimate, since if we'd use 133 MHz clocks for standard
SDHCI controllers, we'd not able to scale frequency down to 400 kHz.
But eSDHC controllers have a non-standard SD clock management, so we can
divide clock by 256 * 16, not just 256.
This patch introduces get_min_clock() callback for sdhci core and
implements it for sdhci-of driver, and thus fixes the issue.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SDHCI controller found in the VX855ES requires 10ms
delay between applying power and applying clock.
This issue has been discovered and documented by the OLPC XO1.5 team.
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Some hosts (hardware configurations, or particular SD/MMC slots) may
not support 4-bit bus. For example, on MPC8569E-MDS boards we can
switch between serial (1-bit only) and nibble (4-bit) modes, thought
we have to disable more peripherals to work in 4-bit mode.
Along with some small core changes, this patch modifies sdhci-of
driver, so that now it looks for "sdhci,1-bit-only" property in the
device-tree, and if specified we enable a proper quirk.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Add quirk to show the controller cannot do multi-block IO.
This is mainly for the Samsung SDHCI controller that currently
cannot manage to do multi-block PIO without timing out.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Because of granularity issues, sometimes we told the hardware to change
to the voltage we were already at. Rework the logic so this doesn't
happen.
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
FSL eSDHC controllers can support maximum block size up to 4096 bytes,
the MBL (Maximum Block Length) field in the capabilities register
extended by one bit, and is set to 0x3.
But the SDHCI core doesn't support blocks of 4096 bytes, and thus
forces blksz to the lowest value -- 512 bytes. With this patch we can
pin up the blksz to the maximum supported block size, i.e. 2048 bytes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
FSL eSDHC controllers losing signal/interrupt enable states after
reset, so we should re-enable them.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Small udelay is needed to make eSDHC work in PIO mode. Without
the delay reading causes endless interrupt storm, and writing
corrupts data. The first guess would be that we must wait for
some bit in some register, but I didn't find any reliable bits
that change before and after the delay.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
FSL eSDHC hosts have incompatible register map to manage the SDCLK.
This patch adds set_clock callback so that drivers could overwrite
set_clock behaviour.
Similar patch[1] was posted by Ben Dooks, though in Ben's version the
callback is named change_clock, plus the patch has some unrelated bits
that makes the patch difficult to reuse.
[1] http://lkml.org/lkml/2008/12/2/160
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some controllers do not provide clock information in their capabilities
(in the Samsung case, it is because there are multiple clock sources
available to the controller). Add hooks to allow the system to supply
clock information.
p.s.
In the original Ben's patch there was a bug that makes sdhci_add_host()
return -ENODEV even if callbacks were specified. This is fixed now.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds SDHCI_QUIRK_INVERTED_WRITE_PROTECT quirk. When
specified, the sdhci driver will invert WP state.
p.s. Actually, the quirk is more board-specific than
controller-specific.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds SDHCI_QUIRK_BROKEN_CARD_DETECTION quirk. When specified,
sdhci driver will set MMC_CAP_NEEDS_POLL MMC host capability, and won't
enable card insert/remove interrupts.
This is needed for hosts with unreliable card detection, such as FSL
eSDHC. The original eSDHC driver was tring to "debounce" card-detection
IRQs by reading present state and disabling particular interrupts. But
with this debouncing scheme I noticed that sometimes we miss card
insertion/removal events.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Card detection interrupts should be handled separately as they should
not be enabled before mmc_add_host() returns and should be disabled
before calling mmc_remove_host(). The same is for suspend and resume
routines.
sdhci_init() no longer enables card-detection irqs. Instead, two new
functions implemented: sdhci_enable_card_detection() and
sdhci_disable_card_detection().
New sdhci_reinit() call implemented to behave the same way as the old
sdhci_init().
Also, this patch implements and uses few new helpers to manage IRQs in
a more conveinient way, that is:
- sdhci_clear_set_irqs()
- sdhci_unmask_irqs()
- sdhci_mask_irqs()
- SDHCI_INT_ALL_MASK constant
sdhci_enable_sdio_irq() converted to these new helpers, plus the
helpers will be used by the subsequent patches.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Currently the SDHCI driver works with PCI accessors (write{l,b,w} and
read{l,b,w}).
With this patch drivers may change memory accessors, so that we can
support hosts with "weird" IO memory access requirments.
For example, in "FSL eSDHC" SDHCI hardware all registers are 32 bit
width, with big-endian addressing. That is, readb(0x2f) should turn
into readb(0x2c), and readw(0x2c) should be translated to
le16_to_cpu(readw(0x2e)).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The Samsung SDHCI (and FSL eSDHC) controller block seems to fail
to generate an INT_DATA_END after the transfer has completed and
the bus busy state finished.
Changes in e809517f6f to use the
new busy method are the cause of the behaviour change.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Fix the led device naming for the sdhci driver.
The led class documentation defines the led name to have the
form "devicename:colour:function" while not applicable sections
should be left blank.
To comply with the documentation the led device name is changed
from "mmc*" to "mmc*::".
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This reverts commit a4b7619377.
It turned out that the controller had problem running at the
higher speed, so go back to trusting the hardware capability
bits.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
CONFIG_LEDS_CLASS is defined only if led-class is built-in, otherwise
when it is a module the option is called CONFIG_LEDS_CLASS_MODULE. Led
support should also be activated in this case.
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some high speed capable controllers forget to set the high speed
capability bit. Make sure we enable the functionality anyway.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
alpha:
drivers/mmc/host/sdhci.h:242: error: field 'sg_miter' has incomplete type
Cc: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the scatter-gather DMA mode present on newer controllers.
As the mode requires 32-bit alignment, non-aligned chunks are handled by
using a bounce buffer.
Also add some new quirks to handle controllers that have bugs in the
ADMA engine.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Gracefully handle when the device is suddenly removed. Do a test read
and avoid any further access if that read returns -1.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Give the quirk for broken timeout handling a better chance of handling
more controllers by simply classifying the system as broken and setting
a fixed value.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The SDHCI interface is not PCI specific, yet the Linux driver was
intimitely connected to the PCI bus. This patch properly separates
the PCI specific portion from the bus independent code.
This patch is based on work by Ben Dooks but he did not have time
to complete it.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Otherwise it can only take the values 0/-1 which doesn't seem to
have been intended.
drivers/mmc/host/sdhci.h:190:20: error: dubious one-bit signed bitfield
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Pierre Ossman <drzeus-list@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hook up the controller LED to the LED subsystem, allowing more flexible
control than simply indicating an ongoing request.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some devices have several controllers; need add the index info to
device slot name host->slot_desc[]
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some controllers have been designed on the assumption that all transfers
will be 32-bit aligned, both in start address and in size. This is not a
guarantee the SDHCI specification provides and not one we can provide.
Revert back to PIO for individual requests in order to work around the
hardware bug.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
It is fully legal for a controller to start issuing data related
interrupts before it has signalled that the command has completed.
Make sure the driver actually can handle this.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The controller has a bit indicating that one of the higher bits (the
error bits) are set. A previous bug caused this bit to be masked, but
since that bug has been fixed we have to clear it explicictly.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
