1
Commit Graph

169130 Commits

Author SHA1 Message Date
Daniel Silverstone
2330ed18b2 Input: usbtouchscreen - add support for Zytronic capacitive touchscreen
Zytronic USB-attached capacitive touchscreen support within the generic
USB touchscreen driver.

Signed-off-by: Daniel Silverstone <dsilvers@simtec.co.uk>
Signed-off-by: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-11-23 08:52:08 -08:00
Roger Quadros
721a730ece Input: force feedback - fix function name in comment
Function name is input_ff_destroy() and not input_ff_free()

Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-11-23 08:51:48 -08:00
Márton Németh
6236dfaa90 Input: do not overwrite the first part of phys string
Use strlcat() to append a string to the previously created first part.

Signed-off-by: Márton Németh <nm127@freemail.hu>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-11-23 08:50:52 -08:00
Pavel Machek
52ce4eaa38 Input: ads7846 - switch to using dev_vdbg()
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-11-23 08:50:07 -08:00
Pavel Machek
30ad7ba0a5 Input: ads7846 - fix pressure reporting
On Zaurus, hx4700 and others pressure is reported inverted -- the lighter
the pressure, the bigger numerical value.

Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-11-23 08:49:58 -08:00
Oliver Neukum
722232bcd8 Input: usbtouchscreen - remove unneeded usb_kill_urb
usb_kill_urb() in disconnect is not needed as unregistering will cause
close() to be called.

Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-11-23 08:49:31 -08:00
Len Brown
87c687be05 ACPI: DMI init_set_sci_en_on_resume for HP-Compaq C700
...else ACPI thermal controls fail after resume.

http://bugzilla.kernel.org/show_bug.cgi?id=13745

Signed-off-by: Len Brown <len.brown@intel.com>
2009-11-23 11:44:12 -05:00
Mark Brown
50b6bce59d ASoC: Fix suspend with active audio streams
When we get a stream suspend event force the power down since otherwise
the stream would remain marked as active.  In future we'll probably want
to make this stream-specific and add an interface to make the power down
of other widgets optional in order to support leaving bypass paths
active while suspending the processor.

Cc: stable@kernel.org
Reported-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-11-23 13:11:53 +00:00
Patrick McHardy
8fa539bd91 netfilter: xt_limit: fix invalid return code in limit_mt_check()
Commit acc738fe (netfilter: xtables: avoid pointer to self) introduced
an invalid return value in limit_mt_check().

Signed-off-by: Patrick McHardy <kaber@trash.net>
2009-11-23 13:37:23 +01:00
Alexander Beregalov
63edaf6476 Au1x00: fix crash when trying register_netdev()
Andreas Lohre reported that the driver crashes when trying
to register_netdev(), he sugessted to move dev->netdev_ops initialization
before calling register_netdev(), it worked for him.

Reported-by: Andreas Lohre <alohre@gmail.com>
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-22 20:40:52 -08:00
Dan Williams
56adf7e812 shdma: fix initialization error handling
1/ Error handling code following a kzalloc should free the allocated data.
2/ Report an error when no platform data is detected

Both problems fixed by moving the platform data check before the allocation,
and allows a goto to be killed.

Reported-by: Julia Lawall <julia@diku.dk>
Acked-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2009-11-22 12:10:10 -07:00
Russell King
cefbf4ea62 MAINTAINERS: add maintainer information for AMBA primecell drivers
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-11-22 17:40:28 +00:00
Russell King
c8a79c3da1 Merge branch 'fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6 2009-11-22 17:11:06 +00:00
Pavel Machek
81065518ed [ARM] pxa/spitz: fix compile regression on spitz
If CONFIG_AKITA is not set, spitz fails to compile. It worked ok in
rc5. Fix is one more ifdef...

Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Stanislav Brabec <utx@penguin.cz>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
2009-11-22 09:32:43 -06:00
Narender Kumar
5d09e534bb netxen : fix BOND_MODE_TLB/ALB mode.
o Along with netdev->perm_addr, mac address will be
  maintained in device private structure.

o Device limitation: We need to set mac address when ever
  interface comes up.

In ALB/TAL mode, bonding driver calls set_mac for all slave with bond mac address.
But bonding driver set netdev->dev_addr field to its original value,
after enslaving interfaces.

When ever active slave changes, it swap dev_addr of inactive slave with active.
Yet it doesn't notify driver about change in netdev->dev_addr.

As netxen driver need to set mac addr when ever interface comes up,
it can't rely on netdev->dev_addr field. Specially in case of bonding mode ALB/TLB.

Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21 11:37:37 -08:00
Narender Kumar
a7483b0afa netxen: fix promisc for NX2031.
Kernel crashes, if promisc mode set without disabling rx queue.
Before changing mode in NX2031 chip, wait till rx queue drains.

Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21 11:37:35 -08:00
Amit Kumar Salecha
5d521fd36d netxen: fix memory initialization
Avoid resetting memory during initialization, skip this memory
block during driver probe.

Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21 11:37:32 -08:00
Russell King
f8d5e5a8f5 ARM: PNX4008: i2c-pnx: use the same dev_id for request_irq and free_irq
This allows i2c-pnx to free its interrupt handler when the module
is removed or if an error occurs; using the same dev_id for both
request_irq and free_irq is desirable.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Ben Dooks <ben-linux@fluff.org>
2009-11-21 19:01:05 +00:00
Jay Fenlason
31769cef2e firewire: ohci: pass correct iso xmit timestamps to core
Here is the final set of patches I used to get ffado to work with the
new firewire stack.  With these patches, I was able to start ardour
and record from and playback to my PreSonus Inspire1394 from a
(mostly) Fedora 12 system.

Signed-off-by: Jay Fenlason <fenlason@redhat.com>

Until now, firewire-ohci exposed only the transmit cycle of the last
transmitted packet at each isochronous transmit complete event.  This
made it impossible for FFADO (FireWire audio drivers in userspace) to
synchronize audio-out streams.  The fix is to store the timestamp of
each packet in the iso xmit event.  As a bonus, the transfer status is
stored too.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2009-11-21 00:56:47 +01:00
chaithrika@ti.com
507eebef86 TI DaVinci EMAC: Minor macro related updates
Use BIT for macro definitions wherever possible, remove
unused and redundant macros.

Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-20 13:57:54 -08:00
David J. Choi
4a91ca4e18 drivers/net: ks8851_mll ethernet network driver -resubmit
Summary of Changes:

	-Fix to receive multicast packets by setting the corresponding hardware
	 bit during initialization.
	-Fix to re-enable the interface [by interface up command(ifup)] while the
	 interface is down.
	-Fix to be able to down the interface by passing the last parameter
	 correctly to request_irq().
	-Remove to read 4 extra bytes from the receiving queue after reading a
	 packet, even though it does not cause a predictable issue now.
	-Remove occurrences of transmission done interrupt in order to tx
	 throughput enhancement.
	-Enable IP checksum for packet receiving by setting the corresponding
	 hardware bit during initialization.
	-Relocate ks_enable_int()/ks_disable_int() in order not to declare those
	 functions at the beginning of the file.
	-Rename ks_enable()/_disable() to ks_enable_qmu()/ks_disable_qmu() in
	 order to give more meaningful names and relocate them not declaire
	 those functions at the beginning of the file.

Signed-off-by: David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-20 13:53:36 -08:00
Geert Uytterhoeven
0ebe74e7ba net: ETHOC should depend on HAS_DMA
When building for Sun 3:

drivers/net/ethoc.c:1091: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `ethoc_probe':
drivers/net/ethoc.c:965: undefined reference to `dma_alloc_coherent'
drivers/net/ethoc.c:1063: undefined reference to `dma_free_coherent'

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-20 13:53:33 -08:00
Bruce Allan
818f33313c e1000e: do not initiate autonegotiation during OEM configuration
When configuring the OEM bits in the PHY on 82577/82578, do not restart
autonegotiation if the firmware is blocking it (e.g. when an IDE-R session
is active) because the link must not go down.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-20 13:53:32 -08:00
Bruce Allan
189983d469 e1000e: remove unnecessary 82577 workaround causing link issues
A workaround for pre-release versions of 82577 is causing link issues on
some switches.  The workaround is no longer needed on production parts so
remove it.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-20 13:53:29 -08:00
Bruce Allan
610c992884 e1000e: flow control thresholds not correct when changing mtu
When changing MTU, save it off prior to resetting otherwise the flow control
thresholds may be miscalculated.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-20 13:53:27 -08:00
Bruce Allan
4c86e0b945 e1000e: add Tx timeout factor for 100Mbps
On some devices (e.g. 82578) not having a Tx timeout factor when linked at
100Mbps can cause false reports of hardware hangs on busy hubs.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-20 13:53:26 -08:00
Bruce Allan
29afd69063 e1000e: set flow control thresholds properly after enabling/disabling pause
When flow control (pause) parameters were changed via ethtool (i.e. enabled
or disabled), the newly calculated thresholds were not being written to the
device for non-fiber media.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-20 13:53:24 -08:00
Bruce Allan
842ec8b64a e1000e: read of PHY register may access wrong page on 82578
Remove unnecessary workaround that mistakenly does not perform a page
select operation for PHY registers 29 and 30 (assuming these are the PHY
debug port address and data registers) on 82578 which can cause reads
of the Transmit with No Carrier Sense statistics register on page 778 to be
read from an incorrect page.  Also error out if the page select operation
fails.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-20 13:53:22 -08:00
Bruce Allan
38eb394e33 e1000e: partial revert of 3ec2a2b8 plus FC workraround for 82577/8
Commit 3ec2a2b80f broke Tx/Rx when using
jumbo frames on certain parts (i.e. only PAUSE frames could be exchanged
once the high water mark was reached preventing normal packet traffic).
This patch reverts the breakage and sets appropriate high and low water
marks of the Rx FIFO for 82577/82578 which require a workaround due to a
flow control issue in hardware.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-20 13:53:20 -08:00
David Howells
4fa9f4ede8 FS-Cache: Provide nop fscache_stat_d() if CONFIG_FSCACHE_STATS=n
Provide nop fscache_stat_d() macro if CONFIG_FSCACHE_STATS=n lest errors like
the following occur:

	fs/fscache/cache.c: In function 'fscache_withdraw_cache':
	fs/fscache/cache.c:386: error: implicit declaration of function 'fscache_stat_d'
	fs/fscache/cache.c:386: error: 'fscache_n_cop_sync_cache' undeclared (first use in this function)
	fs/fscache/cache.c:386: error: (Each undeclared identifier is reported only once
	fs/fscache/cache.c:386: error: for each function it appears in.)
	fs/fscache/cache.c:392: error: 'fscache_n_cop_dissociate_pages' undeclared (first use in this function)

Signed-off-by: David Howells <dhowells@redhat.com>
2009-11-20 21:50:44 +00:00
David Howells
1c2ea8a2c0 SLOW_WORK: Fix GFS2 to #include <linux/module.h> before using THIS_MODULE
GFS2 has been altered to pass THIS_MODULE to slow_work_register_user(), but
hasn't been altered to #include <linux/module.h> to provide it, resulting in
the following error:

	fs/gfs2/recovery.c:596: error: 'THIS_MODULE' undeclared here (not in a function)

Add the missing #include.

Signed-off-by: David Howells <dhowells@redhat.com>
2009-11-20 21:50:40 +00:00
David Howells
0109d7e614 SLOW_WORK: Fix CIFS to pass THIS_MODULE to slow_work_register_user()
As of the patch:

	SLOW_WORK: Wait for outstanding work items belonging to a module to clear

	Wait for outstanding slow work items belonging to a module to clear
	when unregistering that module as a user of the facility.  This
	prevents the put_ref code of a work item from being taken away before
	it returns.

slow_work_register_user() takes a module pointer as an argument.  CIFS must now
pass THIS_MODULE as that argument, lest the following error be observed:

	fs/cifs/cifsfs.c: In function 'init_cifs':
	fs/cifs/cifsfs.c:1040: error: too few arguments to function 'slow_work_register_user'

Signed-off-by: David Howells <dhowells@redhat.com>
2009-11-20 21:50:36 +00:00
Jaswinder Singh Rajput
30b768323f ixgbe: move tc variable to CONFIG_IXGBE_DCB
tc is required by CONFIG_IXGBE_DCB.
This also fixes compilation warning:

 drivers/net/ixgbe/ixgbe_main.c: In function ‘ixgbe_tx_is_paused’:
 drivers/net/ixgbe/ixgbe_main.c:245: warning: unused variable ‘tc’

Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-20 13:47:27 -08:00
Daniel Mack
68a31de302 [ARM] pxa/cpufreq: fix index assignments for end marker
I stumbled over two small things regarding the .index field assignment
in the dynamically created cpu frequency tables for pxa2xx and pxa3xx.

Even though that doesn't currently cause any problem, it should still be
fixed in case the logic in the CPUFREQ core changes.

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
2009-11-20 14:23:13 -06:00
Steven Rostedt
463bf90007 kconfig: Fix make O=<dir> local{mod,yes}config
When the output directory is something other than the kernel source,
the streamline_config script gets confused. This patch passes in the
source directory to the script so that it can find the proper files.

Reported-by: Peter Zijlstra <peterz@infradead.org>
Tested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
2009-11-20 09:45:55 -05:00
Russell King
1508c99506 ARM: PNX4008: fix watchdog device driver name
The PNX core code calls the device 'pnx4008-watchdog' not 'watchdog'

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
2009-11-20 14:23:36 +00:00
Russell King
4ff1fa278b [ARM] kmap: fix build errors with DEBUG_HIGHMEM enabled
d451564 broke ARM by requiring KM_IRQ_PTE, KM_NMI and KM_NMI_PTE to
always be defined.  Solve this by providing invalid definitions for
these constants, but only if CONFIG_DEBUG_HIGHMEM is enabled.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-11-20 14:23:36 +00:00
Nicolas Ferre
985f37f827 AT91: add touchscreen support for at91sam9g45ekes
New at91sam9g45ekes board provides a LCD with resistive touchscreen.
This is the support of this feature by atmel_tsadcc driver. This also
sets up platform parameters to be passed to the driver.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-11-20 00:55:38 -08:00
Nicolas Ferre
423c9b0dc3 AT91: add platform parameters for atmel_tsadcc in at91sam9rlek
Setup platform parameters in at91sam9rl-ek board to be passed to
atmel_tsadcc touchscreen.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-11-20 00:55:29 -08:00
Nicolas Ferre
970435a141 Input: atmel_tsadcc - use platform parameters
Add a number of plafrom dependent parameters to atmel_tsadcc.  The
touchscreeen driver can now take into account the slight differences
that exist between IPs included in diferent products.  This will also
allow to adapt its behaivior to the caracteristics of the resistive
panel used.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-11-20 00:55:21 -08:00
Nicolas Ferre
ab9122cd33 Input: atmel_tsadcc - rework setting touchscreen capabilities
Tiny patch for setting capabilities using input API function.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-11-20 00:55:12 -08:00
Alan Jenkins
0c09b2ac35 Input: keyboard - fix theoretical race on vt switch
A VT switch can theoretically change fg_console between

        vc = vc_cons[fg_console].d
and
        kbd = kbd_table + fg_console

Fix it by replacing the second fg_console with vc->vc_num.

Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-11-20 00:52:14 -08:00
Maxim Levitsky
71bb21b677 Input: ALPS - add support for touchpads with 4-directional button
The touchpad on Acer Aspire 5720, 5520 and some other Aspire models
(signature 0x73, 0x02, 0x50) has a button that can be rocked in 4
different directions. Make the driver to generate BTN_0..BTN_3 events
in response. The Synaptics driver by default maps BTN_0 and BTN_1 to
up and down, so there should be no visible changes with the old setup
that generated BTN_FORWARD and BTN_BACK (also mapped to up and down).

Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-11-20 00:52:13 -08:00
Dmitry Torokhov
315eb996d5 Input: psmouse - rework setting of BTN_MIDDLE capability
Do not start protocol detection assuming that middle mouse is present,
instead let individual protocols explicitly set this capability.
This fixes issue with Synaptics touchpads pretending that they have
middle button when hardware clearly reports otherwise.

Reported-and-tested-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-11-20 00:52:12 -08:00
Dmitry Torokhov
0cc1770b66 Input: lifebook - do not advertise unsupported buttons
The main input device of Lifebook touchscreens does not generate
left/right/middle button events and therefore should not be advertising
them in its capabilities.

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-11-20 00:52:12 -08:00
Dmitry Torokhov
c7a1f3ccfc Input: elantech - do not advertise relative events
Elantech touchpads work in absolute mode and do not generate relative
events so they should not be advertising them.

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-11-20 00:52:11 -08:00
Dmitry Torokhov
21f25573fb Input: touchkit_ps2 - do not advertise unsupported buttons
Touchkit PS/2 touchscreen does not have left/right/middle buttons and
should not be advertising as capable of generating these events.

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-11-20 00:52:10 -08:00
Dmitry Torokhov
d69249f4b6 Input: input-polldev, matrix-keypad - include in kernel doc
Make sure that polled input device and matrix keypad APIs are included
with the rest of input API when generating kernel documentation. Also
description of absres was missing as well.

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-11-20 00:52:09 -08:00
Samu Onkalo
dad725d089 Input: input-polldev - add sysfs interface for controlling poll interval
Sysfs entry for reading and setting of the polling interval. If the
interval is set to 0, polling is stopped. Polling is restarted when
interval is changed to non-zero.

sysfs entries:
poll = current polling interval in msec (RW)
max = max allowed polling interval (RO)
min = min allowed polling interval (RO)

Minimum and maximum limit for interval can be set while setting up the
device.

Interval can be adjusted even if the input device is not currently open.

[dtor@mail.ru: add kernel doc markup for the new fields]
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-11-20 00:52:09 -08:00
Ben Dooks
bc8f1eaf68 Input: gpio_keys - seperate individual button setup to make code neater
Move the code that deals with setting up each individual button out into
a new function to reduce the indentation and allow us to common up some
of the error recovery code.

Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-11-20 00:52:08 -08:00