Currently, almost every interface type has a 'bss' pointer
pointing to BSS information. This BSS information, however,
is for a _local_ BSS, not for the BSS we joined, so having
it on a STA mode interface makes little sense, but now they
have it pointing to the master device, which is an AP mode
virtual interface. However, except for some bitrate control
data, this pointer is only used in AP/VLAN modes (for power
saving stations.)
Overall, it is not necessary to even have the master netdev
be a valid virtual interface, and it doesn't have to be on
the list of interfaces either.
This patch changes the master netdev to be special, it now
- no longer is on the list of virtual interfaces, which
lets me remove a lot of tests for that
- no longer has sub_if_data attached, since that isn't used
Additionally, this patch changes some vlan/ap mode handling
that is related to these 'bss' pointers described above (but
in the VLAN case they actually make sense because there they
point to the AP they belong to); it also adds some debugging
code to IEEE80211_DEV_TO_SUB_IF to validate it is not called
on the master netdev any more.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes call of ieee80211_bss_info_change_notify from within
ieee80211_reset_erp_info. This allows gathering all bss info changes
into one call to the driver in the disassociation flow.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes warning unused variable ifsta
when compiling without CONFIG_MAC80211_VERBOSE_DEBUG
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds block ack request capability
Signed-off-by: Ester Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Probe responses shouldn't be encrypted, and mac80211 doesn't
set the crypto key accordingly. However it didn't set the
IEEE80211_TX_CTL_DO_NOT_ENCRYPT flag which means drivers
could make an attempt to encrypt it, and causing a NULL
pointer dereference when accessing the provided hw_key field.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't report a 'selected' IBSS in sta_find_ibss when none was found.
Signed-off-by: Vladimir Koutny <vlado@ksp.sk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Putting netif_carrier_on before configuring the driver/device with the
new association state may cause a race (tx frames may be sent before
configuration is done)
Signed-off-by: Guy Cohen <guy.cohen@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch reworks the mac80211 debug settings making them more focused
and adding help text for those that didn't have one. It also removes a
number of printks that can be triggered remotely and add no value, e.g.
"too short deauthentication frame received - ignoring".
If somebody really needs to debug that they should just add a monitor
interface and look at the frames in wireshark.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a beacon timestamp to the beacon template used in IBSS
mode. This way the underlying driver can update its TSF accordingly.
According the spec station should adopt the highest TSF from an incoming
beacons in the cell.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the duplicated parsing of information elements
in ieee80211_rx_bss_info and in ieee_rx_mgmt_beacon
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ester Kummer <ester.kummer@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the interval between the scan results and the last time a
beacon was received in the result of the scan.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch add spectrum capability and required information
elements to association request providing AP has requested it and
it is supported by the driver
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding shared key authentication is not going to happen anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch handles the 11h measurement request information element.
This is minimal requested implementation - refuse measurement.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces parsing of 11h and 11d related elements from incoming
management frames.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Three major portions to this change:
1) Add IW_EV_COMPAT_LCP_LEN, IW_EV_COMPAT_POINT_OFF,
and IW_EV_COMPAT_POINT_LEN helper defines.
2) Delete iw_stream_check_add_*(), they are unused.
3) Add iw_request_info argument to iwe_stream_add_*(), and use it to
size the event and pointer lengths correctly depending upon whether
IW_REQUEST_FLAG_COMPAT is set or not.
4) The mechanical transformations to the drivers and wireless stack
bits to get the iw_request_info passed down into the routines
modified in #3. Also, explicit references to IW_EV_LCP_LEN are
replaced with iwe_stream_lcp_len(info).
With a lot of help and bug fixes from Masakazu Mokuno.
Signed-off-by: David S. Miller <davem@davemloft.net>
In IBSS mode prior to join/creation of new IBSS it is possible that
a frame from unknown station is received and an ibss_add_sta() is
called. This will cause a warning in rate_lowest_index() since the
list of supported rates of our station is not initialized yet.
The fix is to add ibss stations with a rate we received that frame
at; this single-element set will be extended later based on beacon
data. Also there is no need to store stations from a foreign IBSS.
Signed-off-by: Vladimir Koutny <vlado@ksp.sk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes setting beacon interval
1. in register_hw it honors value requested by the driver
2. It uses default 100 instead of 1000 or 10000. Scanning for beacon
interval ~1sec and above is not sane
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a check to the set_channel flow. When attempting to change
the channel while in IBSS mode, and the new channel does not support IBSS
mode, the flow return with an error value with no consequences on the
mac80211 and driver state.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sufficient scans (at least 2 or 3) should have been done within 7
seconds to find an existing IBSS to join. This should improve IBSS
creation latency; and since IBSS merging is still in effect, shouldn't
have detrimental effects on eventual IBSS convergence.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otherwise userspace has no idea the IBSS creation succeeded.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows to disable FAT channel in specific configurations.
For example the configuration (8, +1), (primary channel 8, extension
channel 12) isn't permitted in U.S., but (8, -1), (primary channel 8,
extension channel 4) is. When FAT channel configuration is not
permitted, FAT channel should be reported as not supported in the
capabilities of the HT IE in association request. And sssociation is
performed on 20Mhz channel.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds HT IE in the scan list that is returned to user level
through wext. This is useful to let wpa_supplicant if a bss supports 11n or
not: WEP and TKIP are not supported in 11n.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This addresses an alignment issue with compare_ether_addr().
The addresses passed to compare_ether_addr should be two bytes aligned.
It may function properly in x86 platform. However may not work properly
on IA-64 or ARM processor.
This also fixes a typo in mlme.c where the sk_buff struct name is incorect.
Though sizeof() works for any incorrect structure pointer name as its just
a pointer length that we want, lets just fix it.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This addresses a NULL pointer dereference in sta_info_get().
TID and sta_info are extracted in ADDBA Timer expiry function
through the timer handler's argument.
The problem is extracging the TID (which was stored in
timer_to_tid[] array of type "u8") through "int *" typecast which
may also yield unwanted bytes for the MSB of TID that results
in incorrect sta_info and ieee80211_local pointers.
ieee80211_local pointer is NULL as illustrated below, it crashes in
sta_info_get(). The problem started when extracting ieee80211_local
pointer out of sta_info iteself and eventually crashed in
stat_info_get().
The proper way to fix is to change the data type of TID to u8
instead of u16. However changing all the occurences requires
some prototype changes as well. We should fix this in upcoming
patches.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch switch order of channel and freq (SIOCGIWFREQ) reports
in scan results in order to overcome wpa_supplicant inability
to handle channel numbers in 5.2Ghz band.
Wext reporting channel number is ambiguous as channels 7-12 (802.11j)
exist on both bands.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes iee80211_rx_bss_put/get imbalance
introduced by 'mac80211: enable IBSS merging' patch.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts mac80211 and all drivers to have transmit
information and status in skb->cb rather than allocating extra
memory for it and copying all the data around. To make it fit,
a union is used where only data that is necessary for all steps
is kept outside of the union.
A number of fixes were done by Ivo, as well as the rt2x00 part
of this patch.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch modifies struct ieee80211_tx_control to give band
info and the rate index (instead of rate pointers) to drivers.
This mostly serves to reduce the TX control structure size to
make it fit into skb->cb so that the fragmentation code can
put it there and we can think about passing it to drivers that
way in the future.
The rt2x00 driver update was done by Ivo, thanks.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a possible NULL pointer dereference in ieee80211_compatible_rates
introduced in the patch "mac80211: fix association with some APs". If no bss
is available just use all supported rates in the association request.
Signed-off-by: Helmut Schaa <hschaa@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the association problem with 11n hidden ssid ap.
Patch fixes the problem of associating with hidden ssid when
all three parameters ap,essid and channel are given to iwconfig.
This patch removes the condition of checking three parameters
and always checks for bss in bss list while associating.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
trying to clean up the signal/noise code. the previous code in mac80211 had
confusing names for the related variables, did not have much definition of
what units of signal and noise were provided and used implicit mechanisms from
the wireless extensions.
this patch introduces hardware capability flags to let the hardware specify
clearly if it can provide signal and noise level values and which units it can
provide. this also anticipates possible new units like RCPI in the future.
for signal:
IEEE80211_HW_SIGNAL_UNSPEC - unspecified, unknown, hw specific
IEEE80211_HW_SIGNAL_DB - dB difference to unspecified reference point
IEEE80211_HW_SIGNAL_DBM - dBm, difference to 1mW
for noise we currently only have dBm:
IEEE80211_HW_NOISE_DBM - dBm, difference to 1mW
if IEEE80211_HW_SIGNAL_UNSPEC or IEEE80211_HW_SIGNAL_DB is used the driver has
to provide the maximum value (max_signal) it reports in order for applications
to make sense of the signal values.
i tried my best to find out for each driver what it can provide and update it
but i'm not sure (?) for some of them and used the more conservative guess in
doubt. this can be fixed easily after this patch has been merged by changing
the hardware flags of the driver.
DRIVER SIGNAL MAX NOISE QUAL
-----------------------------------------------------------------
adm8211 unspec(?) 100 n/a missing
at76_usb unspec(?) (?) unused missing
ath5k dBm dBm percent rssi
b43legacy dBm dBm percent jssi(?)
b43 dBm dBm percent jssi(?)
iwl-3945 dBm dBm percent snr+more
iwl-4965 dBm dBm percent snr+more
p54 unspec 127 n/a missing
rt2x00 dBm n/a percent rssi+tx/rx frame success
rt2400 dBm n/a
rt2500pci dBm n/a
rt2500usb dBm n/a
rt61pci dBm n/a
rt73usb dBm n/a
rtl8180 unspec(?) 65 n/a (?)
rtl8187 unspec(?) 65 (?) noise(?)
zd1211 dB(?) 100 n/a percent
drivers/net/wireless/ath5k/base.c: Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As discussed earlier, we can unify locking in struct sta_info
and use just a single spinlock protecting all members of the
structure that need protection. Many don't, but one of the
especially bad ones is the 'flags' member that can currently
be clobbered when RX and TX is being processed on different
CPUs at the same time.
Because having four spinlocks for different, mostly exclusive
parts of a single structure is overkill, this patch also kills
the ampdu and mesh plink spinlocks and uses just a single one
for everything. Because none of the spinlocks are nested, this
is safe.
It remains to be seen whether or not we should make the sta
flags use atomic bit operations instead, for now though this
is a safe thing and using atomic operations instead will be
very simple using the new static inline functions this patch
introduces for accessing sta->flags.
Since spin_lock_bh() is used with this lock, there shouldn't
be any contention even if aggregation is enabled at around the
same time as both requires frame transmission/reception which
is in a bh context.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Tomas Winkler <tomasw@gmail.com>
Cc: Ron Rindjunsky <ron.rindjunsky@intel.com>
Cc: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes mac80211 only announce QoS/HT support when
the underlying hardware has four (or more) queues.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Ron Rindjunksi <ron.rindjunksi@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some APs refuse association if the supported rates contained in the
association request do not match its own supported rates. This patch
introduces a new function which builds the intersection between the AP's
supported rates and the client's supported rates to work around such
problems. The same approach is already used in ipw2200 for example.
Signed-off-by: Helmut Schaa <hschaa@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This
* makes the queue number passed to drivers a u16
(as it will be with skb_get_queue_mapping)
* removes the useless queue number defines
* splits hw->queues into hw->queues/ampdu_queues
* removes the debugfs files for per-queue counters
* removes some dead QoS code
* removes the beacon queue configuration for IBSS
so that the drivers now never get a queue number
bigger than (hw->queues + hw->ampdu_queues - 1)
for tx and only in the range 0..hw->queues-1 for
conf_tx.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sta_rx_agg_session_timer_expired() can now become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch corrects the allocation of skb in ADDBA req/resp and DELBA
it removes redundant space u.addba_* are already counted in sizeof(*mgmt)
Signed-off-by: Ester Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This has some code cleanups (some inspired by checkpatch), I got
bored at probably a third of the output though so if somebody
else wants to...
Signed-off-by: Johannes Berg <johannes@sipsolutions.net
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The put routine first decrements the users counter and then
(if it is zero) locks the sta_bss_lock and removes one from
the list and the hash.
Thus, any of ieee80211_sta_config_auth, ieee80211_rx_bss_get
or ieee80211_rx_mesh_bss_get can race with it by finding a
bss that is about to get kfree-ed.
Using atomic_dec_and_lock in ieee80211_rx_bss_put takes care
of this race.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are two structures named wmm_info and wmm_param, they are used while
parsing the beacon frame. (Check the function ieee802_11_parse_elems).
Certain APs like D-link does not set the fifth bit in WMM IE.
While sending the association request to n-only ap it checks for wmm_ie.
If it is set then only ieee80211_ht_cap is sent during association request.
So n-only association fails.
And this patch fixes this problem by copying the wmm_info to wmm_ie,
which enables the "wmm" flag in iee80211_send_assoc.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch reworks the scanning code (ieee80211_rx_bss_info) to take
more parameters from beacons and keep a BSS info structure alive when
only beacons for it are received. This fixes a problem with iwlwifi
drivers (where we don't understand the root cause of the problem yet)
and another driver for some broken hardware (which cannot send probe
requests unless associated, so can't always actively scan.)
Signed-off-by: Bill Moss <bmoss@clemson.edu>
[jmberg: reformatted comments, make probe_resp a bool]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to send BSS changes to driver from beacons processed
during scanning. We are more interested in beacons from an AP with which
we are associated - these will still be used to send updates to driver as
the beacons are received without scanning.
This change·removes the requirement that bss_info_changed needs to be atomic.
The beacons received during scanning are processed from a tasklet, but if we
do not call bss_info_changed for these beacons there is no need for it to be
atomic. This function (bss_info_changed) is called either from workqueue or
ioctl in all other instances.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
