Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters
IB: Put rlimit accounting struct in struct ib_umem
IB/uverbs: Export ib_umem_get()/ib_umem_release() to modules
It is preferable to group drivers by usage (net, scsi, ATA, ...) than
by bus. When reviewing drivers, the [PCI|USB|PCMCIA|...] maintainer
is probably less qualified on networking issues than a networking
maintainer. Also, from a practical standpoint, chips often
appear on multiple buses, which is why we do not put drivers into
drivers/pci/net.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add an InfiniBand driver for Mellanox ConnectX adapters. Because
these adapters can also be used as ethernet NICs and Fibre Channel
HBAs, the driver is split into two modules:
mlx4_core: Handles low-level things like device initialization and
processing firmware commands. Also controls resource allocation
so that the InfiniBand, ethernet and FC functions can share a
device without stepping on each other.
mlx4_ib: Handles InfiniBand-specific things; plugs into the
InfiniBand midlayer.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch lets RBTX49XX boards use generic platform_driver interface
for the ne driver.
* Use platform_device to pass ioaddr and irq to the ne driver.
* Remove unnecessary ifdefs for RBTX49XX from the ne driver.
* Make the ne driver selectable on these boards regardless of CONFIG_ISA
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As SMC91X ethernet controller are used in blackfin STAMP 533 development
board, this patch add blackfin support to the smc91x linux driver.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (38 commits)
kconfig: fix mconf segmentation fault
kbuild: enable use of code from a different dir
kconfig: error out if recursive dependencies are found
kbuild: scripts/basic/fixdep segfault on pathological string-o-death
kconfig: correct minor typo in Kconfig warning message.
kconfig: fix path to modules.txt in Kconfig help
usr/Kconfig: fix typo
kernel-doc: alphabetically-sorted entries in index.html of 'htmldocs'
kbuild: be more explicit on missing .config file
kbuild: clarify the creation of the LOCALVERSION_AUTO string.
kbuild: propagate errors from find in scripts/gen_initramfs_list.sh
kconfig: refer to qt3 if we cannot find qt libraries
kbuild: handle compressed cpio initramfs-es
kbuild: ignore section mismatch warning for references from .paravirtprobe to .init.text
kbuild: remove stale comment in modpost.c
kbuild/mkuboot.sh: allow spaces in CROSS_COMPILE
kbuild: fix make mrproper for Documentation/DocBook/man
kbuild: remove kconfig binaries during make mrproper
kconfig/menuconfig: do not hardcode '.config'
kbuild: override build timestamp & version
...
Fix a race condition in the transmit code, where the dma interrupt could update
the free tx buffer count concurrently and wedge the tx queue.
Fix the misuse of the rx frame status and rx frame length registers: no more
"fifo overrun" errors caused by the OFLOW bit being tested in the frame length
register (instead of the status register), and no more missed packets due to
incorrect length taken from status register (instead of the frame length
register).
Fix a panic (skb_over_panic BUG) caused by allocating and then copying an
incoming packet while the packet length register was changing.
Cut-and-paste the reset code from the powermac mace driver (mace.c), so the NIC
functions when MacOS does not initialise it (important for anyone wanting to
use the Emile boot loader).
Cut-and-paste the error counting and timeout recovery code from mace.c.
Fix over allocation of rx buffer memory (it's page order, not page count).
Converted to driver model.
Converted to DMA API.
Since I've run out of ways to make it fail, and since it performs well now,
promote the driver from EXPERIMENTAL status. Tested on both quadra 840av and
660av.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Macintosh CS89x0 Ethernet: Netif updates
Addition of netif_stop_queue() before transmission by Michael Schmitz
skb_copy_{from,to}_linear_data() conversion by Geert Uytterhoeven
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Documentation/modules.txt doesn't exist, but
Documentation/kbuild/modules.txt does.
Signed-off-by: Alexander E. Patrakov
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
[IPV4] SNMP: Support OutMcastPkts and OutBcastPkts
[IPV4] SNMP: Support InMcastPkts and InBcastPkts
[IPV4] SNMP: Support InTruncatedPkts
[IPV4] SNMP: Support InNoRoutes
[SNMP]: Add definitions for {In,Out}BcastPkts
[TCP] FRTO: RFC4138 allows Nagle override when new data must be sent
[TCP] FRTO: Delay skb available check until it's mandatory
[XFRM]: Restrict upper layer information by bundle.
[TCP]: Catch skb with S+L bugs earlier
[PATCH] INET : IPV4 UDP lookups converted to a 2 pass algo
[L2TP]: Add the ability to autoload a pppox protocol module.
[SKB]: Introduce skb_queue_walk_safe()
[AF_IUCV/IUCV]: smp_call_function deadlock
[IPV6]: Fix slab corruption running ip6sic
[TCP]: Update references in two old comments
[XFRM]: Export SPD info
[IPV6]: Track device renames in snmp6.
[SCTP]: Fix sctp_getsockopt_local_addrs_old() to use local storage.
[NET]: Remove NETIF_F_INTERNAL_STATS, default to internal stats.
[NETPOLL]: Remove CONFIG_NETPOLL_RX
...
Get rid of the CONFIG_NETPOLL_RX option completely since all the
dependencies have been removed long ago...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Transmit on Demand: Fix spelling in config option, and make it actually enable TOD.
Signed-off-by: Michael Reiss <michael.f.reiss@freescale.com>
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
migrate ucc_geth to use the common phylib code.
There are several side effects from doing this:
o deprecate 'interface' property specification present
in some old device tree source files in
favour of a split 'max-speed' and 'interface-type'
description to appropriately match definitions
in include/linux/phy.h. Note that 'interface' property
is still honoured if max-speed or interface-type
are not present (backward compatible).
o compile-time CONFIG_UGETH_HAS_GIGA is eliminated
in favour of probe time speed derivation logic.
o adjust_link streamlined to only operate on maccfg2
and upsmr.r10m, instead of reapplying static initial
values related to the interface-type.
o Addition of UEC MDIO of_platform driver requires
platform code add 'mdio' type to id list
prior to calling of_platform_bus_probe (separate patch).
o ucc_struct_init introduced to reduce ucc_geth_startup
complexity.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Current tc35815 driver is very obsolete and less maintained for a long
time. Replace it with a new driver based on one from CELF patch
archive.
Major advantages of CELF version (version 1.23, for kernel 2.6.10) are:
* Independent of JMR3927.
(Actually independent of MIPS, but AFAIK the chip is used only on
MIPS platforms)
* TX4938 support.
* 64-bit proof.
* Asynchronous and on-demand auto negotiation.
* High performance on non-coherent architecture.
* ethtool support.
* Many bugfixes and cleanups.
And improvoments since version 1.23 are:
* TX4939 support.
* NETPOLL support.
* NAPI support. (disabled by default)
* Reduce memcpy on receiving.
* PM support.
* Many cleanups and bugfixes.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change the Kconfig files so that the Freescale QE options are automatically
selected if a QE device is selected. Previously, you'd need to manually
select UCC_FAST if you want any "fast" UCC devices, such as Gigabit Ethernet.
Now, the QE Gigabit Ethernet option is always available if the device has a
QE, and UCC_FAST is automatically enabled. A side-effect is that the
"QE Options" menu no longer exists.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The driver attempts to upgrade the FW if the card has the wrong version.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds or changes some HW specific settings for spider_net on
Celleb.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* master.kernel.org:/pub/scm/linux/kernel/git/kyle/parisc-2.6: (78 commits)
[PARISC] Use symbolic last syscall in __NR_Linux_syscalls
[PARISC] Add missing statfs64 and fstatfs64 syscalls
Revert "[PARISC] Optimize TLB flush on SMP systems"
[PARISC] Compat signal fixes for 64-bit parisc
[PARISC] Reorder syscalls to match unistd.h
Revert "[PATCH] make kernel/signal.c:kill_proc_info() static"
[PARISC] fix sys_rt_sigqueueinfo
[PARISC] fix section mismatch warnings in harmony sound driver
[PARISC] do not export get_register/set_register
[PARISC] add ENTRY()/ENDPROC() and simplify assembly of HP/UX emulation code
[PARISC] convert to use CONFIG_64BIT instead of __LP64__
[PARISC] use CONFIG_64BIT instead of __LP64__
[PARISC] add ASM_EXCEPTIONTABLE_ENTRY() macro
[PARISC] more ENTRY(), ENDPROC(), END() conversions
[PARISC] fix ENTRY() and ENDPROC() for 64bit-parisc
[PARISC] Fixes /proc/cpuinfo cache output on B160L
[PARISC] implement standard ENTRY(), END() and ENDPROC()
[PARISC] kill ENTRY_SYS_CPUS
[PARISC] clean up debugging printks in smp.c
[PARISC] factor syscall_restart code out of do_signal
...
Fix conflict in include/linux/sched.h due to kill_proc_info() being made
publicly available to PARISC again.
Remove the use of CONFIG_MV643XX_ETH_[012] variables on most platforms.
Instead, platform-specific code enables the ports supported by the
hardware. After this patch, these config variables are only used in
arch/ppc, so also move them from drivers/net/Kconfig to arch/ppc/Kconfig.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: Paul Mackerras <paulus@samba.org>
sk98lin is scheduled for removal in July 2007. This patch makes the
deprecation more obvious in the configuration interface. FWIW, Gentoo have
been shipping a patch very similar to this for a long time.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove the experimental tag for the pcnet32 NAPI implementation.
Signed-off-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The atl1 driver doesn't need NET_PCI. Remove it from Kconfig.
Noticed by Chad Sprouse.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-tc:
[EISA] EISA registration with !CONFIG_EISA
[TC] pmagb-b-fb: Convert to the driver model
[TC] dec_esp: Driver model for the PMAZ-A
[TC] mips: pmag-ba-fb: Convert to the driver model
[TC] defxx: TURBOchannel support
[TC] TURBOchannel support for the DECstation
[TC] MIPS: TURBOchannel resources off-by-one fix
[TC] MIPS: TURBOchannel update to the driver model
This is a set of changes to add TURBOchannel support to the defxx driver. As
at this point the EISA support in the driver has become the only not having
been converted to the driver model, I took the opportunity to convert it as
well. Plus support for MMIO in addition to PIO operation as TURBOchannel
requires it anyway.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This driver is a modified version of the Attansic reference driver
for the L1 ethernet adapter. Attansic has granted permission for
its inclusion in the mainline kernel.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Atmel MACB Ethernet peripheral is also integrated in the AT91SAM9260
and AT91SAM9263 processors. The differences from the AVR32 version are:
* Single peripheral clock.
* MII/RMII selection bit is inverted.
* Clock enable bit.
Original patch from Patrice Vilchez.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Driver for the PA Semi PWRficient on-chip Ethernet (1/10G)
Basic enablement, will be complemented with performance enhancements
over time. PHY support will be added as well.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use bitrev8 for bmac, mace, macmace, macsonic, and skfp drivers.
[akpm@osdl.org: use the API, not the array]
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Mirko Lindner <mlindner@syskonnect.de>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The OAKNET driver:
- has been marked as BROKEN for more than two years and
- is still marked as BROKEN.
Drivers that had been marked as BROKEN for such a long time seem to be
unlikely to be revived in the forseeable future.
But if anyone wants to ever revive this driver, the code is still
present in the older kernel releases.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This driver is required by the Chelsio T3 RDMA driver posted by
Steve Wise.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The SKMC driver has:
- already been marked as BROKEN in 2.6.0 three years ago and
- is still marked as BROKEN.
Drivers that had been marked as BROKEN for such a long time seem to be
unlikely to be revived in the forseeable future.
But if anyone wants to ever revive this driver, the code is still
present in the older kernel releases.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a driver for the Silan SC92031/Rsltek 8139D NIC chip.
This chip is found on at least one counterfeit Encore ENL832-TX-RENT NIC
[1], which came with a mini-CD with the 2.4 driver. A slightly older
version of the driver was found at [2]. The main difference between them
is that the newer one has a small bugfix in the RX path, a lot of
gratuitous renaming of functions, all the printable strings changed to show
as a "Rsltek 8139D" [sic], and a PCI ID of 8139 instead of 2031. The
driver on this patch is a rewrite of the vendor drivers (based mostly on
the older one).
Changes from the previous patch sent to netdev:
- Use MMIO instead of PIO
- Changed TX bounce buffers allocation
- Use skb_copy_and_csum_dev
- Several small bug fixes
- Tested for more than just a few minutes each time
[1] See http://www.encore-usa.com/faq.php under ENL832-TX-RENT for more
information
[2] Look for SL_LINUX.ZIP (which is really a .tar.gz) at
http://broadbandforum.in/dataone_Intex_LAN_cardlinux-t4207-s15.html
[3] To compile on 2.6.17, simply add back the last argument to the
interrupt handler in two places, and copy the boolean declarations
from 2.6.19
[akpm@osdl.org: build fixes]
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This driver tries to enable/disable NAPI at runtime, but
does so in an unsafe manner, and the NAPI interrupt handling is
a mess. Replace it with a compile time selected NAPI implementation.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If we separate out LASI and ASP support later, we'll need this.
Plus, this makes it consistent with the ncr700 scsi driver.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Replace driver crc calculation with existing library.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for other versions of the 10G Chelsio boards.
This is basically a port of the vendor driver with the
TOE features removed.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/built-in.o: In function `netxen_nic_remove':
netxen_nic_main.c:(.text+0x31b4d): undefined reference to `pci_disable_msi'
netxen_nic_main.c:(.text+0x31b8e): undefined reference to `pci_release_regions'
drivers/built-in.o: In function `netxen_init_module':
netxen_nic_main.c:(.init.text+0x3f17): undefined reference to `pci_module_init'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Driver for the Atmel MACB on-chip ethernet module.
Tested on AVR32/AT32AP7000/ATSTK1000. I've heard rumours that it works
with AT91SAM9260 as well, and it may be possible to share some code with
the at91_ether driver for AT91RM9200.
Hardware documentation can be found in the AT32AP7000 data sheet,
which can be downloaded from
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
Changes since previous version:
* Probe for PHY ID instead of depending on it being provided through
platform_data.
* Grab initial ethernet address from the MACB registers instead
of depending on platform_data.
* Set MII/RMII mode correctly.
These changes are mostly about making the driver more compatible with
the at91 infrastructure.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add tsi108/9 on chip Ethernet controller driver support.
The driver code collects the feedback of previous posting form the mailing
list and gives the update.
MPC7448HPC2 platform in arch/powerpc uses tsi108 bridge.
The following is a brief description of the Ethernet controller:
The Tsi108/9 Ethernet Controller connects Switch Fabric to two independent
Gigabit Ethernet ports,E0 and E1. It uses a single Management interface to
manage the two physical connection devices (PHYs). Each Ethernet port has
its own statistics monitor that tracks and reports key interface
statistics. Each port supports a 256-entry hash table for address
filtering. In addition, each port is bridged to the Switch Fabric through
a 2-Kbyte transmit FIFO and a 4-Kbyte Receive FIFO.
Each Ethernet port also has a pair of internal Ethernet DMA channels to
support the transmit and receive data flows. The Ethernet DMA channels use
descriptors set up in memory, the memory map of the device, and access via
the Switch Fabric. The Ethernet Controller’s DMA arbiter handles
arbitration for the Switch Fabric. The Controller also has a register bus
interface for register accesses and status monitor control.
The PMD (Physical Media Device) interface operates in MII, GMII, or TBI
modes. The MII mode is used for connecting with 10 or 100 Mbit/s PMDs.
The GMII and TBI modes are used to connect with Gigabit PMDs. Internal
data flows to and from the Ethernet Controller through the Switch Fabric.
Each
Ethernet port uses its transmit and receive DMA channels to manage data
flows through buffer descriptors that are predefined by the system (the
descriptors can exist anywhere in the system memory map). These
descriptors are data structures that point to buffers filled with data
ready to transmit over Ethernet, or they point to empty buffers ready to
receive data from Ethernet.
Signed-off-by: Alexandre Bounine <Alexandre.Bounine@tundra.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
