Quicc Engine enabled mpc83xx CPU's has a somewhat different HW interface to
the SPI controller. This patch adds a qe_mode knob that sees to that
needed adaptions are performed.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The MPC83xx SPI controller clock divider can divide the system clock by not
more then 1024. The spi_mpc83xx driver does not check this and silently
writes garbage to the SPI controller registers when asked to run at lower
frequencies. I've tried to run the SPI on a 266MHz MPC8349E with 100kHz
for debugging a bus problem and suddenly was confronted with a 2nd problem
to debug.. ;-)
The patch adds an additional check which avoids writing garbage to the SPI
controller registers and warn the user about it. This might help others to
avoid simmilar problems.
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minor SPI controller driver updates: make the setup() methods reject
spi->mode bits they don't support, by masking aginst the inverse of bits
they *do* support. This insures against misbehavior later when new mode
bits get added.
Most controllers can't support SPI_LSB_FIRST; more handle SPI_CS_HIGH.
Support for all four SPI clock/transfer modes is routine.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some issues were recently turned up with the current specification of what
it means for spi_transfer.tx_buf to be null, as part of transfers which are
(from the SPI protocol driver perspective) pure reads.
Specifically, that it seems better to change the TX behaviour there from
"undefined" to "will shift zeroes". This lets protocol drivers (like the
ads7846 driver) depend on that behavior. It's what most controller drivers
in the tree are already doing (with one exception and one case of driver
wanting-to-oops), it's what Microwire hardware will necessarily be doing,
and it removes an issue whereby certain security audits would need to
define such a value anyway as part of removing covert channels.
This patch changes the specification to require shifting zeroes, and
updates all currently merged SPI controller drivers to do so.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
This driver supports the SPI controller on the MPC83xx SoC devices from
Freescale. Note, this driver supports only the simple shift register SPI
controller and not the descriptor based CPM or QUICCEngine SPI controller.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
