The IO access of PCI is not supported in R7780RP and the MS7780SE
board now. The support of the IO access mode of e100 and a lot of IDE
chips becomes possible by fixing the code.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
PCI IO space base address of SH7780 was wrong.
Change from 0xFE400000 to 0xFE200000.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes iwl_mac_add_interface.
1. Currently only one interface is supported, instead of silently retuning
0 now it returns -EOPNOTSUPP (By Johannes Berg)
2. It enables changing mac address from user space (By Ian Schram)
Signed-off-by: Tomas Winkler <tomas@localhost.localdomain>
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: linux-wireless <linux-wireless@vger.kernel.org
Cc: Ian Schram <ischram@telenet.be>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
lbs_mac_event_disconnected() was called once and then never again
upon a hardware MAC event.
The reason was that the driver didn't clean the correct bit in the interrupt
cause register of the chip.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I'm not sure why it was doing this, and I'm not sure I _want_ to know
why. But calling it NETIF_F_DYNALLOC doesn't change the fact that the
kernel believes it to be NETIF_F_IPV6_CSUM, and that IPv6 communication
is hence buggered.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix some left-over URLs and ifdefs in b43 and b43legacy drivers.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Saleem Abdulrasool <compnerd@compnerd.org>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The attached patch rate limits "WEP decrypt failed (ICV)" to avoid
flooding the logfiles.
Signed-off-by: Adel Gadllah <adel.gadllah@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rfkill_toggle_radio is called from functions where
rfkill->mutex is already aquired.
Remove the lock from rfkill_toggle_radio() and add it to
the only calling function that calls it without the lock held.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a regression I (most likely) introduced, namely that
unencrypted frames are right now accepted even if we have a key for that
specific sender. That has very bad security implications.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes:
- Incorrect calls to ieee80211_hw_config when the radiotap flag is set.
- Failure to actually unset the radiotap flag when all monitors are down.
- Failure to call ieee80211_hw_config after successful interface start.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no guarantee that data+SNAP_SIZE will reside on an even numbered
address, so doing a 16 bit read will cause an unaligned access in some
situations. Based on a patch from Jun Sun.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I'm not sure if this is best choice, someone might have better
solutions. But this patch fixed the connection problem when switching
from a WPA enabled AP (using wpa_supplicant) to an open AP (using
iwconfig). The root cause is when we connect to a WPA enabled AP,
wpa_supplicant sets the ifsta->extra_ie thru SIOCSIWGENIE. But if we
stop wpa_supplicant and connect to an open AP with iwconfig, there is
no way to clear the extra_ie so that mac80211 keeps connecting with that.
Someone could argue wpa_supplicant should clear the extra_ie during
its shutdown. But mac80211 should also handle the unexpected shutdown
case (ie. killall -9 wpa_supplicant).
On Wed, 2007-11-21 at 16:19 +0100, Johannes Berg wrote:
> Yeah. Can you amend the patch to also clear the
> IEEE80211_STA_PRIVACY_INVOKED flag?
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If NR_IRQS is defined as a sum without surrounding parentheses, this may
lead to problems when used in multiplications. This may lead to problems
in:
arch/ia64/sn/kernel/irq.c:516
arch/x86/kernel/io_apic_32.c:693, 694, 699, 700
fs/proc/proc_misc.c:464
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: bridge wu <bridge.wu@marvell.com>
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some platforms (e.g. Littleton) requires LCD PCLK drive strength to be
higher than default to cope with the fast PCLK frequency.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This also fixes a sparse warning about different signedness.
Only compile tested, because i do not have the hardware.
Signed-off-by: Andre Haupt <andre@bitwigglers.org>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Subdividing the paravirt_ops structure caused a regression in certain
non-GPL modules which try to use mmu_ops and cpu_ops. This restores the
old behaviour, and makes it consistent with the non-CONFIG_PARAVIRT case.
Takashi Iwai <tiwai@suse.de> adds:
> I took at this problem (as I have an nvidia card on one of my
> workstations), and found out that the following suffer from
> EXPORT_SYMBOL_GPL changes:
>
> * local_disable_irq(), local_irq_save*(), etc.
> * MSR-related macros like rdmsr(), wrmsr(), read_cr0(), etc.
> wbinvd(), too.
> * pmd_val(), pgd_val(), etc are all involved with pv_mm_ops.
> pmd_large() and pmd_bad() is also indirectly involved.
> __flush_tlb() and friends suffer, too.
Christoph Hellwig objects to this patch on the grounds that modules
shouldn't be using these operations anyway. I don't think this is a
particularly good reason to reject the patch, for several reasons:
1. These operations are still available to modules when not using
CONFIG_PARAVIRT, since they are implicitly exported as inline
functions via the kernel headers. Exporting the same functionality as
GPL-only symbols just adds a gratuitious difference between
CONFIG_PARAVIRT and non-CONFIG_PARAVIRT configurations. If we really
think these operations are not for module use (or non-GPL module use),
then we should solve the problem in a general way.
2. It's a regression from previous kernels, which would work these
modules even with CONFIG_PARAVIRT enabled.
3. The operations in question seem pretty reasonable for modules to
use. The control registers/MSRs can be accessed directly anyway, so there's
no benefit in preventing modules from using standard interfaces. And it seems
reasonable to allow a graphics driver to create its own mappings if it wants.
Therefore, I think this patch should go in for 2.6.24. If people
really think that these operations should not be available to modules,
then we can address that separately.
Signed-off-by: Jeremy Fitzhardinge <Jeremy.Fitzhardinge@citrix.com>
Cc: Tobias Powalowski <t.powa@gmx.de>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Keep lguest from being enabled on VISWS or VOYAGER configs, just as is
already done for VMI and XEN. Otherwise randconfigs with VISWS and LGUEST
have this problem:
In file included from arch/x86/kernel/setup_32.c:61:
include/asm-x86/mach-visws/setup_arch.h:8:1: warning: "ARCH_SETUP" redefined
In file included from include/asm/msr.h:80,
from include/asm/processor_32.h:17,
from include/asm/processor.h:2,
from include/asm/thread_info_32.h:16,
from include/asm/thread_info.h:2,
from include/linux/thread_info.h:21,
from include/linux/preempt.h:9,
from include/linux/spinlock.h:49,
from include/linux/seqlock.h:29,
from include/linux/time.h:8,
from include/linux/timex.h:57,
from include/linux/sched.h:53,
from arch/x86/kernel/setup_32.c:24:
include/asm/paravirt.h:458:1: warning: this is the location of the previous definition
(and of course, this happens because kconfig does not follow dependencies
when [evil] select is used...)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ACPI uses NR_CPUS in various loops and in some it accesses per cpu data of
processors that are not present(!) and that will never be present.
The pointers to per cpu data are typically not initialized for processors
that are not present. So we seem to be reading something here from offset
0 in memory.
Make ACPI use nr_cpu_ids instead. That stops at the end of the possible
processors.
Convert one loop to NR_CPUS to use the cpu_possible map instead. That way
ranges of processor that can never be brought online are skipped during the
loop.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make them depend on TCGETS2. If that one is implemented the rest should be
there as well.
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In wait_task_stopped() exit_code already contains the right value for the
si_status member of siginfo, and this is simply set in the non WNOWAIT
case.
If you call waitid() with a stopped or traced process, you'll get the signal
in siginfo.si_status as expected -- however if you call waitid(WNOWAIT) at the
same time, you'll get the signal << 8 | 0x7f
Pass it unchanged to wait_noreap_copyout(); we would only need to shift it
and add 0x7f if we were returning it in the user status field and that
isn't used for any function that permits WNOWAIT.
Signed-off-by: Scott James Remnant <scott@ubuntu.com>
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arrange the sections in the FRV arch so that a BRA instruction with a
16-bit displacement can always reach from the trap table to entry.S,
tlb-miss.S and break.S.
The problem otherwise is that the linker can insert sufficient code between
the slots in the trap table and the targets of the branch instructions in
those slots that the displacement field in the instruction isn't
sufficiently large. This is because the branch targets were in the .text
section along with most of the other code in the kernel.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the extern declaration of kallsyms_num_syms to indicate that the symbol
does not reside in the small-data storage space, and so may not be accessed
relative to the small data base register.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
RTC code is using mutex to assure exclusive access to /dev/rtc. This is
however wrong usage, as it leaves the mutex locked when returning into
userspace, which is unacceptable.
Convert rtc->char_lock into bit operation.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Invalidate attributes on rename, since some filesystems may update
st_ctime. Reported by Szabolcs Szakacsits
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I found problems accessing (executing) previously existing files, until
I did chmod on them (or setattr).
If the fi->attr_version is not initialized, then it could be
larger than fc->attr_version until a setattr is executed, and as a
result the inode attributes would never be set.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
FUSE_FILE_OPS is meant to signal that the kernel will send the open file to to
the userspace filesystem for operations on open files, so that sillyrenaming
unlinked files becomes unnecessary.
However this needs VFS changes, which won't make it into 2.6.24.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some open flags (O_APPEND, O_DIRECT) can be changed with fcntl(F_SETFL, ...)
after open, but fuse currently only sends the flags to userspace in open.
To make it possible to correcly handle changing flags, send the
current value to userspace in each read and write.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently reading a fuse file will stop at cached i_size and return
EOF, even though the file might have grown since the attributes were
last updated.
So detect if trying to read past EOF, and refresh the attributes
before continuing with the read.
Thanks to mpb for the report.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds document for EFI x86_64 boot support. The setup and operation
guide of EFI based system is documented in Documentation/x86_64/uefi.txt.
Signed-off-by: Chandramouli Narayanan <mouli@linux.intel.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds Graphics Output Protocol support to the kernel. UEFI2.0 spec
deprecates Universal Graphics Adapter (UGA) protocol and only Graphics Output
Protocol (GOP) is produced. Therefore, the boot loader needs to query the
UEFI firmware with appropriate Output Protocol and pass the video information
to the kernel. As a result of GOP protocol, an EFI framebuffer driver is
needed for displaying console messages. The patch adds a EFI framebuffer
driver. The EFI frame buffer driver in this patch is based on the Intel Mac
framebuffer driver.
The ELILO bootloader takes care of passing the video information as
appropriate for EFI firmware.
The framebuffer driver has been tested in i386 kernel and x86_64 kernel on EFI
platform.
Signed-off-by: Chandramouli Narayanan <mouli@linux.intel.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@suse.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert 7eea436433.
Lucy said:
This patch will work with the 19HS but WILL BREAK all other Keyspan
adapters. It will take me a few days to get to looking at a correct fix but
that keyspan_send_setup(port, 1) (and the '1' is the important part) must
happen once when the port is first opened. The cflag can just be set to
whatever the normal default is for your serial environment.
So revert this again pending the proper fix.
Cc: Borislav Petkov <bbpetkov@yahoo.de>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Lucy McCoy <lucy@keyspan.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With NO_HZ disabled, the UML idle loop effectively becomes a busy loop, as
it will sleep for no time.
The cause was forgetting to restart the tick after waking up from sleep.
It was disabled before sleeping, and the remaining time used as the
interval to sleep. So, the tick needs to be restarted when nanosleep
finishes.
This is done by introducing after_sleep_interval, which is empty in the
NO_HZ case, but which sets the tick starting in the !NO_HZ case.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
got this HiSax bootup crash on a "make randconfig" bzImage bootup:
Calling initcall 0xc0bb1320: HiSax_init+0x0/0x380()
HiSax: Linux Driver for passive ISDN cards
HiSax: Version 3.5 (kernel)
HiSax: Layer1 Revision 2.46.2.5
HiSax: Layer2 Revision 2.30.2.4
HiSax: TeiMgr Revision 2.20.2.3
HiSax: Layer3 Revision 2.22.2.3
HiSax: LinkLayer Revision 2.59.2.4
HiSax: Total 1 card defined
HiSax: Card 1 Protocol EDSS1 Id=HiSax (0)
HiSax: HFC-S driver Rev. 1.10.2.4
HFCS: defined at 0x500 IRQ 5 HZ 250
Teles 16.3c: IRQ 5 count 0
HFCS: resetting card
Teles 16.3c: IRQ 5 count 0
Teles 16.3c: IRQ(5) getting no interrupts during init 1
HFCS: resetting card
------------[ cut here ]------------
kernel BUG at include/linux/timer.h:145!
invalid opcode: 0000 [#1] PREEMPT DEBUG_PAGEALLOC
Modules linked in:
Pid: 1, comm: swapper Not tainted (2.6.24-rc3 #2045)
EIP: 0060:[<c063afbf>] EFLAGS: 00010286 CPU: 0
EIP is at hfcs_card_msg+0x15f/0x180
EAX: c0cf2e5c EBX: 000000f2 ECX: 00000000 EDX: ffff1193
ESI: f76e8000 EDI: f76e8000 EBP: f7c23ec4 ESP: f7c23eac
DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068
Process swapper (pid: 1, ti=f7c22000 task=f7c0e000 task.ti=f7c22000)
Stack: 00000000 f7c23ec4 c011703b 00000002 f76e8000 00000000 f7c23ef8 c060c3e5
c0a7c9c0 c0a315dc 00000005 00000001 00000000 f7c23f34 00000000 c0b5c9c0
f7c23f34 00000000 c0f5a8e0 f7c23f80 c0bb154f 00000000 00000001 c0a9b5b9
Call Trace:
[<c010339a>] show_trace_log_lvl+0x1a/0x40
[<c0103469>] show_stack_log_lvl+0xa9/0xe0
[<c010355f>] show_registers+0xbf/0x200
[<c01037a4>] die+0x104/0x220
[<c0103943>] do_trap+0x83/0xc0
[<c0103ca8>] do_invalid_op+0x88/0xa0
[<c083621a>] error_code+0x6a/0x70
[<c060c3e5>] checkcard+0x4a5/0x620
[<c0bb154f>] HiSax_init+0x22f/0x380
[<c0b867b7>] kernel_init+0x97/0x2a0
[<c0102f87>] kernel_thread_helper+0x7/0x20
=======================
Code: e8 43 ae ff 8b 57 3c 85 d2 0f 84 ef fe ff ff b8 a0 99 ad c0 b9 02 00 00 00 e8 ce 11 ae ff 83 c4 0c b8 00 00 00 00 5b 5e 5f c9 c3 <0f> 0b eb fe 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90
EIP: [<c063afbf>] hfcs_card_msg+0x15f/0x180 SS:ESP 0068:f7c23eac
Kernel panic - not syncing: Attempted to kill init!
The box has no HiSax card installed.
the reason for the crash is add_timer() done on an already running
timer. This happens because for some reason CARD_INIT is called twice.
this patch works this problem around by using mod_timer() - this gets
a booting system - but it would be nice to figure out why CARD_INIT
is done twice.
the ISDN config section (generated via make randconfig) is this:
#
# ISDN feature submodules
#
# CONFIG_ISDN_DRV_LOOP is not set
CONFIG_ISDN_DIVERSION=y
#
# ISDN4Linux hardware drivers
#
#
# Passive cards
#
CONFIG_ISDN_DRV_HISAX=y
#
# D-channel protocol features
#
CONFIG_HISAX_EURO=y
CONFIG_DE_AOC=y
# CONFIG_HISAX_NO_SENDCOMPLETE is not set
# CONFIG_HISAX_NO_LLC is not set
# CONFIG_HISAX_NO_KEYPAD is not set
CONFIG_HISAX_1TR6=y
CONFIG_HISAX_NI1=y
CONFIG_HISAX_MAX_CARDS=8
#
# HiSax supported cards
#
CONFIG_HISAX_16_0=y
# CONFIG_HISAX_16_3 is not set
# CONFIG_HISAX_TELESPCI is not set
CONFIG_HISAX_S0BOX=y
# CONFIG_HISAX_AVM_A1 is not set
CONFIG_HISAX_FRITZPCI=y
CONFIG_HISAX_AVM_A1_PCMCIA=y
CONFIG_HISAX_ELSA=y
CONFIG_HISAX_IX1MICROR2=y
CONFIG_HISAX_DIEHLDIVA=y
# CONFIG_HISAX_ASUSCOM is not set
# CONFIG_HISAX_TELEINT is not set
CONFIG_HISAX_HFCS=y
# CONFIG_HISAX_SEDLBAUER is not set
CONFIG_HISAX_SPORTSTER=y
# CONFIG_HISAX_MIC is not set
# CONFIG_HISAX_NETJET is not set
# CONFIG_HISAX_NETJET_U is not set
# CONFIG_HISAX_NICCY is not set
# CONFIG_HISAX_ISURF is not set
# CONFIG_HISAX_HSTSAPHIR is not set
# CONFIG_HISAX_BKM_A4T is not set
# CONFIG_HISAX_SCT_QUADRO is not set
# CONFIG_HISAX_GAZEL is not set
# CONFIG_HISAX_HFC_PCI is not set
# CONFIG_HISAX_W6692 is not set
# CONFIG_HISAX_HFC_SX is not set
# CONFIG_HISAX_DEBUG is not set
#
# HiSax PCMCIA card service modules
#
#
# HiSax sub driver modules
#
CONFIG_HISAX_ST5481=y
CONFIG_HISAX_HFCUSB=y
# CONFIG_HISAX_HFC4S8S is not set
CONFIG_HISAX_FRITZ_PCIPNP=y
CONFIG_HISAX_HDLC=y
#
# Active cards
#
CONFIG_ISDN_DRV_ICN=m
CONFIG_ISDN_DRV_PCBIT=m
CONFIG_ISDN_DRV_SC=y
# CONFIG_ISDN_DRV_ACT2000 is not set
CONFIG_HYSDN=m
# CONFIG_ISDN_DRV_GIGASET is not set
# CONFIG_ISDN_CAPI is not set
CONFIG_PHONE=y
CONFIG_PHONE_IXJ=m
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Kai Germaschewski <kai@germaschewski.name>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
