The PCI function to physical port mapping is valid only for
old firmware. New firmware (4.0.0+) abstracts this.
So driver should never try to access phy using invalid
mapping. The behavior is unpredictable when PCI functions
4-7 are enabled on the same NIC.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: amend the fix for SO_BSDCOMPAT gsopt infoleak
netns: build fix for net_alloc_generic
de_get is called before every proc_get_inode, but corresponding de_put is
called only when dropping last reference to an inode. This might cause
something like
remove_proc_entry: /proc/stats busy, count=14496
to be printed to the syslog.
The fix is to call de_put in case of an already initialized inode in
proc_get_inode.
Signed-off-by: Krzysztof Sachanowicz <analyzer1@gmail.com>
Tested-by: Marcin Pilipczuk <marcin.pilipczuk@gmail.com>
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the KMS case, enter/leavevt won't fix up the interrupt handler for
us, so we need to do it at suspend/resume time. Make sure we don't fail
the resume if the chip is hung either.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dev_priv->hw_status_page can be NULL, if i915_gem_retire_requests()
is called from i915_gem_busy_ioctl().
Signed-off-by Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The fix for CVE-2009-0676 (upstream commit df0bca04) is incomplete. Note
that the same problem of leaking kernel memory will reappear if someone
on some architecture uses struct timeval with some internal padding (for
example tv_sec 64-bit and tv_usec 32-bit) --- then, you are going to
leak the padded bytes to userspace.
Signed-off-by: Eugene Teo <eugeneteo@kernel.sg>
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net_alloc_generic was defined in #ifdef CONFIG_NET_NS, but used
unconditionally. Move net_alloc_generic out of #ifdef.
Signed-off-by: Clemens Noss <cnoss@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Documentation fix
The amazing dancing boot.txt file has jumped places again. It should
never have been in Documentation/x86/i386, since it never was
32-bit-specific, but it unfortunately ended up there for a while.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
netns: fix double free at netns creation
veth : add the set_mac_address capability
sunlance: Beyond ARRAY_SIZE of ib->btx_ring
sungem: another error printed one too early
ISDN: fix sc/shmem printk format warning
SMSC: timeout reaches -1
smsc9420: handle magic field of ethtool_eeprom
sundance: missing parentheses?
smsc9420: fix another postfixed timeout
wimax/i2400m: driver loads firmware v1.4 instead of v1.3
vlan: Update skb->mac_header in __vlan_put_tag().
cxgb3: Add support for PCI ID 0x35.
tcp: remove obsoleted comment about different passes
TG3: &&/|| confusion
ATM: misplaced parentheses?
net/mv643xx: don't disable the mib timer too early and lock properly
net/mv643xx: use GFP_ATOMIC while atomic
atl1c: Atheros L1C Gigabit Ethernet driver
net: Kill skb_truesize_check(), it only catches false-positives.
net: forcedeth: Fix wake-on-lan regression
Add new USB ID codes. These come from two postings on forums and
mailing lists, and four are derived from the .inf that accompanies
the latest Realtek Windows driver for the RTL8187L.
Thanks to Viktor Ilijašić <viktor.ilijasic@gmail.com> and Xose Vazquez
Perez <xose.vazquez@gmail.com> for reporting these new ID's.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With DEBUG_NOTIFIERS it results in
[11330.890966] WARNING: at /home/bor/src/linux-git/kernel/notifier.c:88
notifier_call_chain+0x91/0xa0()
[11330.890977] Hardware name: PORTEGE 4000
[11330.890983] Invalid notifier called! ...
Without DEBUG_NOTIFIERS it most likely crashes on NULL pointer.
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Acked-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incorrect variable was used to get the next sample which caused S2
to be stuck with the same value resulting in loud background noise.
Signed-off-by: Steve Chen <schen at mvista.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Audiowerk2 driver snd-aw2 is bound to any saa7146 device as it does not
check subsystem ids. Many DVB devices are saa7146 based, so aw2 driver
grabs them as well.
According to http://lkml.org/lkml/2008/10/15/311 aw2 devices have the
subsystem ids set to 0, the saa7146 default.
Fix conflicts with DVB devices by checking for subsystem ids = 0
specifically.
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add missing parameter value to list of available values
for acpi=<value>.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Functions ext4_write_begin() and ext4_da_write_begin() call
grab_cache_page_write_begin() without AOP_FLAG_NOFS. Thus it
can happen that page reclaim is triggered in that function
and it recurses back into the filesystem (or some other filesystem).
But this can lead to various problems as a transaction is already
started at that point. Add the necessary flag.
http://bugzilla.kernel.org/show_bug.cgi?id=11688
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: Add missing mutex_lock(&dev->struct_mutex)
drm/i915: fix WC mapping in non-GEM i915 code.
drm/i915: Fix regression in 95ca9d
drm/i915: Retire requests from i915_gem_busy_ioctl.
drm/i915: suspend/resume GEM when KMS is active
drm/i915: Don't let a device flush to prepare buffers clear new write_domains.
drm/i915: Cut two args to set_to_gpu_domain that confused this tricky path.
there might be a nicer way to fix this but this is the simplest for now.
Signed-off-by: Pierre Willenbrock <pierre@pirsoft.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The object is dereferenced before the NULL check. Oops.
Fixes http://bugs.freedesktop.org/show_bug.cgi?id=20235
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This ensures that the user gets the latest information from the hardware
on whether the buffer is busy, potentially reducing the working set of objects
that the user chooses.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In the KMS case, we need to suspend/resume GEM as well. So on suspend, make
sure we idle GEM and stop any new rendering from coming in, and on resume,
re-init the framebuffer and clear the suspended flag.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The problem was that object_set_to_gpu_domain would set the new write_domains
that are getting set by this batchbuffer, then the accumulated flushes required
for all the objects in preparation for this batchbuffer were posted, and the
brand new write domain would get cleared by the flush being posted. Instead,
hang on to the new (or old if we're not changing it) value and set it after
the flush is queued.
Results from this noticably included conformance test failures from reads
shortly after writes (where the new write domain had been lost and thus not
flushed and waited on), but is a suspected cause of hangs in some apps when
a write domain is lost on a buffer that gets reused for instruction or
commmand state.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
While not strictly required, it helped while thinking about the following
change. This change should be invariant.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
At some point we (okay, I) managed to break the ability for users to use the
setsockopt() syscall to set IPv4 options when NetLabel was not active on the
socket in question. The problem was noticed by someone trying to use the
"-R" (record route) option of ping:
# ping -R 10.0.0.1
ping: record route: No message of desired type
The solution is relatively simple, we catch the unlabeled socket case and
clear the error code, allowing the operation to succeed. Please note that we
still deny users the ability to override IPv4 options on socket's which have
NetLabel labeling active; this is done to ensure the labeling remains intact.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
The CIPSO protocol engine incorrectly stated that the FIPS-188 specification
could be found in the kernel's Documentation directory. This patch corrects
that by removing the comment and directing users to the FIPS-188 documented
hosted online. For the sake of completeness I've also included a link to the
CIPSO draft specification on the NetLabel website.
Thanks to Randy Dunlap for spotting the error and letting me know.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
We've discovered that our AT91SAM9260 board consumed too much power when
returning from a slowclock low-power mode. RAM self-refresh is enabled in
a bootloader in our case, this is how we saw a difference. Estimated ca.
30mA more on 4V battery than the same state before powersaving.
After a small research we found that there seems to be a bogus
sdram_selfrefresh_disable() call at the end of at91_pm_enter() call, which
overwrites the LPR register with uninitialized value. Please find the
suggested patch attached.
This patch fixes correct restoring of LPR register of the Atmel AT91 SDRAM
controller when returning from a power saving mode.
Signed-off-by: Andrei Birjukov <andrei.birjukov@artecdesign.ee>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'core/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
PM: Split up sysdev_[suspend|resume] from device_power_[down|up], fix
Impact: module build fix
Fix:
ERROR: "sysdev_resume" [arch/x86/kernel/apm.ko] undefined!
ERROR: "sysdev_suspend" [arch/x86/kernel/apm.ko] undefined!
As these APIs are now used by the APM driver, which can be built
as a module.
Also fix a few extra (and inconsistent) newlines in comment blocks
preceding these functions.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The kernel-api docbook was much larger than any of the others,
so processing it took longer and needed some docbook extras in
some cases, so split it into kernel-api (infrastructure etc.)
and device drivers/device subsystems. This allows these docbooks
to be generated in parallel. (This reduced the docbook processing
time on my 4-proc system with make -j4 from about 5min:16sec to
about 2min:01sec.)
The chapters that were moved from kernel-api to device-drivers are:
Driver Basics
Device drivers infrastructure
Parallel Port Devices
Message-based devices
Sound Devices
16x50 UART Driver
Frame Buffer Library
Input Subsystem
Serial Peripheral Interface (SPI)
I2C and SMBus Subsystem
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the sysdev_suspend/resume from the callee to the callers, with
no real change in semantics, so that we can rework the disabling of
interrupts during suspend/hibernation.
This is based on an earlier patch from Linus.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Right now nobody cares, but the suspend/resume code will eventually want
to suspend device interrupts without suspending the timer, and will
depend on this flag to know.
The modern x86 timer infrastructure uses the local APIC timers and never
shows up as a device interrupt at all, so it isn't affected and doesn't
need any of this.
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: remove CONFIG_ACPI_SYSTEM
fujitsu-laptop: Use RFKILL support bitmask from firmware
x86_64: Fix S3 fail path
x86_64: acpi/wakeup_64 cleanup
battery: don't assume we are fully charged when not charging or discharging
ACPI: EC: Add delay for slow MSI controller
Fix descriptions of device attributes to be consistent with the actual
implementations in include/linux/device.h
Signed-off-by: Mike Murphy <mamurph[at]cs.clemson.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the presented definition of struct device_attribute to match the
actual definition in include/linux/device.h
Signed-off-by: Mike Murphy <mamurph[at]cs.clemson.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
http://kisskb.ellerman.id.au/kisskb/buildresult/72115/:
| net/mac80211/ieee80211_i.h:327: error: syntax error before 'volatile'
| net/mac80211/ieee80211_i.h:350: error: syntax error before '}' token
| net/mac80211/ieee80211_i.h:455: error: field 'sta' has incomplete type
| distcc[19430] ERROR: compile net/mac80211/main.c on sprygo/32 failed
This is caused by
| # define mfp ((*(volatile struct MFP*)MFP_BAS))
in arch/m68k/include/asm/atarihw.h, which conflicts with the new "mfp" enum in
net/mac80211/ieee80211_i.h.
Rename "mfp" to "st_mfp", as it's a way too generic name for a global #define.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: fix bug
the third param in module_param(,,) is perm instead of default value.
we still need to assign default at first. Also, the default is now
zero not one, so fix the parameter text to reflect that.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The 8390 driver was structured by Al Viro to allow the flexibility
required by platforms. lib8390.c contains the core code which drivers
explicitly include:
- 8390.c includes lib8390.c to provide the standard ISA based driver.
- etherh.c includes it with the accessors defined for RiscPC platforms,
where it is addressed via the MMIO accessors with a device dependent
register spacing.
Other platform drivers do something similar.
However, b9a9b4b caused the kernel to contain not only the etherh
private build of lib8390 (included in etherh.c) but also lib8390.c
itself, and referred the new net_device_ops methods to the ISA version.
The result of this is is not pretty:
Unable to handle kernel paging request at virtual address 12032030
pgd = c8330000
[12032030] *pgd=00000000
Internal error: Oops: 18331805 [#1]
Modules linked in: ipv6
CPU: 0 Not tainted (2.6.29-rc3 #167)
PC is at do_set_multicast_list+0xd0/0x190
LR is at bitrev32+0x28/0x34
pc : [<c017aab4>] lr : [<c0139120>] psr: a0000093
sp : c8321d9c ip : c8321d84 fp : c8321dbc
r10: c80c6800 r9 : 00000000 r8 : c80c6b60
r7 : c80c6b80 r6 : cc80c800 r5 : c80c6800 r4 : 00000000
r3 : cc80c80c r2 : 00000004 r1 : 00000007 r0 : e0000000
Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
...
Fix up b9a9b4b by making etherh's net_device_ops refer to the internal
lib8390 functions, and remove the build of the ISA 8390.c driver.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fix a double free when a network namespace fails.
The previous code does a kfree of the net_generic structure when
one of the init subsystem initialization fails.
The 'setup_net' function does kfree(ng) and returns an error.
The caller, 'copy_net_ns', call net_free on error, and this one
calls kfree(net->gen), making this pointer freed twice.
This patch make the code symetric, the net_alloc does the net_generic
allocation and the net_free frees the net_generic.
Signed-off-by: Daniel Lezcano <daniel.lezcano@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove CONFIG_ACPI_SYSTEM. It was always set the same as CONFIG_ACPI,
and it had no menu label, so there was no way to set it to anything
other than "y".
Some things under CONFIG_ACPI_SYSTEM (acpi_irq_handled, acpi_os_gpe_count(),
event_is_open, register_acpi_notifier(), etc.) are used unconditionally
by the CA, the OSPM, and drivers, so we depend on them always being
present.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Up until now, we polled the rfkill status for every incoming FUJ02E3 ACPI event.
It turns out that the firmware has a bitmask which indicates what rfkill-related
state it can report.
The rfkill_supported bitmask is now used to avoid polling for rfkill at all in
the notification handler if there is no support. Also, it is used in the platform
device callbacks. As before we register all callbacks and report "unknown" if the
firmware does not give us status updates for that particular bit.
This was fed through checkpatch.pl and tested on the S6420, S7020 and P8010
platforms.
Signed-off-by: Tony Vroon <tony@linx.net>
Tested-by: Stephen Gildea <stepheng+linux@gildea.com>
Acked-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Signed-off-by: Len Brown <len.brown@intel.com>
As acpi_enter_sleep_state can fail, take this into account in
do_suspend_lowlevel and don't return to the do_suspend_lowlevel's
caller. This would break (currently) fpu status and preempt count.
Technically, this means use `call' instead of `jmp' and `jmp' to
the `resume_point' after the `call' (i.e. if
acpi_enter_sleep_state returns=fails). `resume_point' will handle
the restore of fpu and preempt count gracefully.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
- remove %ds re-set, it's already set in wakeup_long64
- remove double labels and alignment (ENTRY already adds both)
- use meaningful resume point labelname
- skip alignment while jumping from wakeup_long64 to the resume point
- remove .size, .type and unused labels
[v2]
- added ENDPROCs
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
