The current HDA generic parser initializes / modifies the amp values
always in stereo, but this seems causing the problem on ALC3229 codec
that has a few mono channel widgets: namely, these mono widgets react
to actions for both channels equally.
In the driver code, we do care the mono channel and create a control
only for the left channel (as defined in HD-audio spec) for such a
node. When the control is updated, only the left channel value is
changed. However, in the resume, the right channel value is also
restored from the initial value we took as stereo, and this overwrites
the left channel value. This ends up being the silent output as the
right channel has been never touched and remains muted.
This patch covers the places where unconditional stereo amp accesses
are done and converts to the conditional accesses.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94581
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MacBook Air 5,2 has the same problem as MacBook Pro 8,1 where the
built-in mic records only the right channel. Apply the same
workaround as MBP8,1 to spread the mono channel via a Cirrus codec
vendor-specific COEF setup.
Reported-and-tested-by: Vasil Zlatanov <vasil.zlatanov@gmail.com>
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CS420x codecs seem to deal only the single amps of ADC nodes even
though the nodes receive multiple inputs. This leads to the
inconsistent amp value after S3/S4 resume, for example.
The fix is just to set codec->single_adc_amp flag. Then the driver
handles these ADC amps as if single connections.
Reported-and-tested-by: Vasil Zlatanov <vasil.zlatanov@gmail.com>
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Compaq Presario CQ60 laptop with CX20561 gives a wrong pin for the
built-in mic NID 0x17 instead of NID 0x1d, and it results in the
non-working mic. This patch just remaps the pin correctly via fixup.
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=920604
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [63e51fd708: ALSA: hda - Don't take unresponsive D3
transition too serious] introduced a conditional fallback behavior to
the HD-audio controller depending on the flag set. However, it
introduced a silly bug, too, that the flag was evaluated in a reverse
way. This resulted in a regression of HD-audio controller driver
where it can't go to the fallback mode at communication errors.
Unfortunately (or fortunately?) this didn't come up until recently
because the affected code path is an error handling that happens only
on an unstable hardware chip. Most of recent chips work stably, thus
they didn't hit this problem. Now, we've got a regression report with
a VIA chip, and this seems indeed requiring the fallback to the
polling mode, and finally the bug was revealed.
The fix is a oneliner to remove the wrong logical NOT in the check.
(Lesson learned - be careful about double negation.)
The bug should be backported to stable, but the patch won't be
applicable to 3.13 or earlier because of the code splits. The stable
fix patches for earlier kernels will be posted later manually.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94021
Fixes: 63e51fd708 ('ALSA: hda - Don't take unresponsive D3 transition too serious')
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is essentially a partial revert of the commit [b1920c2110:
'ALSA: hda - Enable runtime PM on Panther Point']. There was a bug
report showing the HD-audio bus hang during runtime PM on HP Spectre
XT.
Reported-by: Dang Sananikone <dang.sananikone@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It is a bad idea to export static functions. GCC for some platforms
shows errors like:
error: __ksymtab_azx_get_response causes a section type conflict
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BIOS doesn't seem to set up pins for 5.1 and the SPDIF out, so we need
to give explicitly here.
Reported-and-tested-by: Misan Thropos <misanthropos@gmx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
RME RayDAT and AIO use a fixed buffer size of 16384 samples. With period
sizes of 32-4096, this translates to 4-512 periods.
The older RME cards have a variable buffer size but require exactly two
periods.
This patch enforces nperiods=2 on those cards.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Cc: <stable@vger.kernel.org> # 2.6.39+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Otherwise, the mute led can't work at all.
Tested-by: Taihsiang Ho <taihsiang.ho@canonical.com>
Cc: <stable@vger.kernel.org>
BugLink: https://bugs.launchpad.net/bugs/1410704
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In this batch, you can find lots of cleanups through the whole
subsystem, as our good New Year's resolution. Lots of LOCs and
commits are about LINE6 driver that was promoted finally from staging
tree, and as usual, there've been widely spread ASoC changes.
Here some highlights:
ALSA core changes
- Embedding struct device into ALSA core structures
- sequencer core cleanups / fixes
- PCM msbits constraints cleanups / fixes
- New SNDRV_PCM_TRIGGER_DRAIN command
- PCM kerneldoc fixes, header cleanups
- PCM code cleanups using more standard codes
- Control notification ID fixes
Driver cleanups
- Cleanups of PCI PM callbacks
- Timer helper usages cleanups
- Simplification (e.g. argument reduction) of many driver codes
HD-audio
- Hotkey and LED support on HP laptops with Realtek codecs
- Dock station support on HP laptops
- Toshiba Satellite S50D fixup
- Enhanced wallclock timestamp handling for HD-audio
- Componentization to simplify the linkage between i915 and hd-audio
drivers for Intel HDMI/DP
USB-audio
- Akai MPC Element support
- Enhanced timestamp handling
ASoC
- Lots of refactoringin ASoC core, moving drivers to more data
driven initialization and rationalizing a lot of DAPM usage
- Much improved handling of CDCLK clocks on Samsung I2S controllers
- Lots of driver specific cleanups and feature improvements
- CODEC support for TI PCM514x and TLV320AIC3104 devices
- Board support for Tegra systems with Realtek RT5677
- New driver for Maxim max98357a
- More enhancements / fixes for Intel SST driver
Others
- Promotion of LINE6 driver from staging along with lots of rewrites
and cleanups
- DT support for old non-ASoC atmel driver
- oxygen cleanups, XIO2001 init, Studio Evolution SE6x support
- Emu8000 DRAM size detection fix on ISA(!!) AWE64 boards
- A few more ak411x fixes for ice1724 boards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=/84r
-----END PGP SIGNATURE-----
Merge tag 'sound-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"In this batch, you can find lots of cleanups through the whole
subsystem, as our good New Year's resolution. Lots of LOCs and
commits are about LINE6 driver that was promoted finally from staging
tree, and as usual, there've been widely spread ASoC changes.
Here some highlights:
ALSA core changes
- Embedding struct device into ALSA core structures
- sequencer core cleanups / fixes
- PCM msbits constraints cleanups / fixes
- New SNDRV_PCM_TRIGGER_DRAIN command
- PCM kerneldoc fixes, header cleanups
- PCM code cleanups using more standard codes
- Control notification ID fixes
Driver cleanups
- Cleanups of PCI PM callbacks
- Timer helper usages cleanups
- Simplification (e.g. argument reduction) of many driver codes
HD-audio
- Hotkey and LED support on HP laptops with Realtek codecs
- Dock station support on HP laptops
- Toshiba Satellite S50D fixup
- Enhanced wallclock timestamp handling for HD-audio
- Componentization to simplify the linkage between i915 and hd-audio
drivers for Intel HDMI/DP
USB-audio
- Akai MPC Element support
- Enhanced timestamp handling
ASoC
- Lots of refactoringin ASoC core, moving drivers to more data driven
initialization and rationalizing a lot of DAPM usage
- Much improved handling of CDCLK clocks on Samsung I2S controllers
- Lots of driver specific cleanups and feature improvements
- CODEC support for TI PCM514x and TLV320AIC3104 devices
- Board support for Tegra systems with Realtek RT5677
- New driver for Maxim max98357a
- More enhancements / fixes for Intel SST driver
Others
- Promotion of LINE6 driver from staging along with lots of rewrites
and cleanups
- DT support for old non-ASoC atmel driver
- oxygen cleanups, XIO2001 init, Studio Evolution SE6x support
- Emu8000 DRAM size detection fix on ISA(!!) AWE64 boards
- A few more ak411x fixes for ice1724 boards"
* tag 'sound-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (542 commits)
ALSA: line6: toneport: Use explicit type for firmware version
ALSA: line6: Use explicit type for serial number
ALSA: line6: Return EIO if read/write not successful
ALSA: line6: Return error if device not responding
ALSA: line6: Add delay before reading status
ASoC: Intel: Clean data after SST fw fetch
ALSA: hda - Add docking station support for another HP machine
ALSA: control: fix failure to return new numerical ID in 'replace' event data
ALSA: usb: update trigger timestamp on first non-zero URB submitted
ALSA: hda: read trigger_timestamp immediately after starting DMA
ALSA: pcm: allow for trigger_tstamp snapshot in .trigger
ALSA: pcm: don't override timestamp unconditionally
ALSA: off by one bug in snd_riptide_joystick_probe()
ASoC: rt5670: Set use_single_rw flag for regmap
ASoC: rt286: Add rt288 codec support
ASoC: max98357a: Fix build in !CONFIG_OF case
ASoC: Intel: fix platform_no_drv_owner.cocci warnings
ARM: dts: Switch Odroid X2/U2 to simple-audio-card
ARM: dts: Exynos4 and Odroid X2/U3 sound device nodes update
ALSA: control: fix failure to return numerical ID in 'add' event
...
Make sure wallclock counter and trigger timestamp are read very
close to each other for better alignment.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The problem here is that we check:
if (dev >= SNDRV_CARDS)
Then we increment "dev".
if (!joystick_port[dev++])
Then we use it as an offset into a array with SNDRV_CARDS elements.
if (!request_region(joystick_port[dev], 8, "Riptide gameport")) {
This has 3 effects:
1) If you use the module option to specify the joystick port then it has
to be shifted one space over.
2) The wrong error message will be printed on failure if you have over
32 cards.
3) Static checkers will correctly complain that are off by one.
Fixes: db1005ec6f ('ALSA: riptide - Fix joystick resource handling')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Toshiba Satellite S50D laptop with an IDT codec uses the GPIO4 (0x10)
as the master EAPD.
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=915858
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like previous patches, at this time we embed the struct device into
PCM object. However, this needs a bit more caution: struct snd_pcm
doesn't own one device but two, for both playback and capture! Thus
not struct snd_pcm but struct snd_pcm_str object contains the device.
Along with this change, pcm->dev field is dropped for avoiding
confusion. It was meant to point to a non-standard parent. But,
since now we can touch each struct device directly, we can manipulate
the parent field easily there, too.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like the previous patch, this one embeds the device object into hwdep
object. For a proper object lifecycle, it's freed in the release
callback.
This also allows us to create sysfs entries via passing to the groups
field of the device without explicit function calls. Since each
driver can see the device and touch its groups field directly, we
don't need to delegate in hwdep core any longer. So, remove the
groups field from snd_hwdep, and let the user (in this case only
hda_hwdep.c) modify the device groups.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Define snd_ak4114_suspend() and snd_ak4114_resume() functions to
handle PM properly, stopping and restarting the work at PM.
Currently only ice1712/juli.c deals with the PM and ak4114, so fix the
calls there appropriately.
The same PM functions are defined in ak4113.c, too, although they
aren't currently called yet (ice1712/quartet.c may be enhanced to
support PM later).
Acked-by: Jaroslav Kysela <perex@perex.cz>
Tested-by: Pavel Hofman <pavel.hofman@ivitera.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On this machine we need to inform the driver where the docking
station pins are, because it has not been set up by BIOS.
Tested-by: TienFu Chen <tienfu.chen@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1412800
Signed-off-by: TienFu Chen <tienfu.chen@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Configure the XIO2001 bridge on PCI Express cards so that it does less
needless prefetching.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make it possible for cards to have three stereo analog input pairs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cards without S/PDIF output do not need those controls.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit commit [33f4acd3b2: ALSA: hda - Enable mic mute hotkey
and LEDs for an HP machine] introduced a quirk for a HP machine
involving with the input event handling. Although the relevant code
is protected via IS_ENABLED(CONFIG_INPUT), this doesn't suffice when
the audio driver is built in while the input is module.
As an easy workaround, this patch forcibly selects CONFIG_INPUT in
Kconfig. This shouldn't be a practical problem since CONFIG_INPUT is
almost mandatory for all systems. Also, this allows to remove the
ugly ifdefs in the code.
Fixes: 33f4acd3b2 ('ALSA: hda - Enable mic mute hotkey and LEDs for an HP machine')
Acked-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Conflicts:
drivers/net/xen-netfront.c
Minor overlapping changes in xen-netfront.c, mostly to do
with some buffer management changes alongside the split
of stats into TX and RX.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings below by using snd_pcm_format_t properly:
sound/pci/rme32.c:682:60: sparse: incorrect type in argument 2 (different base types)
sound/pci/rme96.c:1006:69: sparse: incorrect type in argument 2 (different base types)
.....
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Register a component master to be used to interface with the i915
driver. This is meant to replace the current interface which is based on
module symbol lookups.
Note that currently we keep the existing behavior and pin the i915
module while the hda driver is loaded. Using the component interface
allows us to remove this dependency once support for dynamically
enabling / disabling the HDMI functionality is added to the driver.
v2:
- change roles between the hda and i915 components (Daniel)
v3:
- rename display_component to audio_component (Daniel)
v4:
- move removal of i915_powerwell.h from this patch to the next (Takashi)
- request_module fails if module support isn't enabled, so ignore
any error it returns and depend on the following NULL check of the
component ops (Takashi)
- change over to using dev_* instead of pr_* (Takashi)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
chip is already passed to most of the i915 interface functions. Unify
the interface by passing intel_hda instead of chip and passing it to all
functions. Passing intel_hda instead of chip makes more sense since this
is an intel specific interface. Also in an upcoming patch we will use
intel_hda in all of these functions so by passing intel_hda we can save
on some pointer casts from chip to intel_hda.
This will be needed by an upcoming patch adding component support.
No functional change.
v2-3: unchanged
v4:
- pass intel_hda instead of chip
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This struct will be needed by the component code added in an upcoming
patch, so export it into a new hda_intel.h file. At the same time also
merge hda_i915.h into this new header, there is no reason to keep two
separate intel specific header file.
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Removes some functions that are not used anywhere:
snd_wm8766_set_power() snd_wm8766_set_master_mode()
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The FSF address is subject to change. So, we remove it from the header.
While here, remove a line with my old and non-functional email from the
header. Moreover, nowadays we have a Git VCS that contains a history of
changes.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Input_unregister_device will internally free the device, so
input_free_device should not be called.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a similar cleanup like the commit [3db084fd0a: ALSA: fm801:
PCI core handles power state for us].
Since pci_set_power_state(), pci_save_state() and pci_restore_state()
are already done in the PCI core side, so we don't need to it doubly.
Also, pci_enable_device(), pci_disable_device() and pci_set_master()
calls in PM callbacks are superfluous nowadays, too, so get rid of
them as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a similar cleanup like the commit [3db084fd0a: ALSA: fm801:
PCI core handles power state for us].
Since pci_set_power_state(), pci_save_state() and pci_restore_state()
are already done in the PCI core side, so we don't need to it doubly.
Also, pci_enable_device(), pci_disable_device() and pci_set_master()
calls in PM callbacks are superfluous nowadays, too, so get rid of
them as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
