Fix the HSM error_mask mapping.
Changes:
- Better mapping in ac_err_mask()
- In HSM_ST_FIRST ans HSM_ST state, check ATA_ERR|ATA_DF and map it to AC_ERR_DEV instead of AC_ERR_HSM.
- In HSM_ST_FIRST and HSM_ST state, map DRQ=1 ERR=1 to AC_ERR_HSM.
- For PIO data in and DRQ=1 ERR=1, add check after the junk data block is read.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This fixes a byte-swap issue on PPC, found by Zang Roy-r61911
on the powerpc platform. His original patch also had some other
platform-specific changes in #ifdef's, but I'm not sure yet how to
incorporate them. Look for another patch for those (soon).
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver currently keeps local copies of the hardware request/response queue indexes.
But it expends significant effort ensuring consistency between the two views,
and still gets it wrong after an error or reset occurs.
This patch removes the local copies, in favour of just accessing the hardware
whenever we need them. Eventually this may need to be tweaked again for NCQ,
but for now this works and solves problems some users were seeing.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The 60xx chips, and possibly others, incorrectly assert DEV_IRQ interrupts
on a regular basis. The cause of this is under investigation (by me and
in theory by Marvell also), but regardless we do need to deal with these events.
This patch tidies up some interrupt handler code, and ensures that we ignore
DEV_IRQ interrupts when the drive still has ATA_BUSY asserted.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The interface control register of the 60xx (and later) Marvell chip
requires certain bits to always be set when writing to it. These bits
incorrectly read-back as zeros, so the pattern must be ORed in
with each write of the register. Also, bit 12 should NOT be set
(note that Marvell's own driver also had bit-12 wrong here).
While we're at it, we also now do pci_set_master() in the init code.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In some systems, it is possible that the BIOS may have enabled interrupt coalescing
for the Marvell controllers which support it. This patch adds code to detect/ack
interrupts from the chip's coalescing (combing) logic.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The mv_err_intr() function is invoked from the driver's interrupt handler,
as well as from the timeout function. This patch prevents it from triggering
a one-after-the-other double reset of the controller when invoked
from the timeout function.
This also adds a check for a timeout race condition that has been observed
to occur with this driver in earlier kernels. This should not be needed,
in theory, but in practice it has caught bugs. Maybe nuke it at a later date.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/mthca: Fix posting lists of 256 receive requests for Tavor
IB/uverbs: Don't leak ref to mm on error path
IB/srp: Complete correct SCSI commands on device reset
IB/srp: Get rid of extra scsi_host_put()s if reconnection fails
IB/srp: Don't wait for disconnection if sending DREQ fails
IB/mthca: Make fw_cmd_doorbell default to 0
Patch from Pavel Pisa
There has been problems that for some paths that clock are not stopped
during new command programming and initiation. Result is issuing
of incorrect command to the card. Some other problems are cleaned too.
Noisy report of known ERRATUM #4 has been suppressed.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If we post a list of length 256 exactly, nreq in doorbell gets set to
256 which is wrong: it should be encoded by 0. This is because we
only zero it out on the next WR, which may not be there. The solution
is to ring the doorbell after posting a WQE, not before posting the
next one.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In ib_umem_release_on_close(), if the kmalloc() fails, then a
reference to current->mm will be leaked. Fix this by adding a mmput()
instead of just returning on kmalloc() failure.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Re-enable posted writes for status FIFO.
Besides bringing back a very minor bandwidth tweak from Linux 2.6.15.x
and older, this also fixes an interoperability regression since 2.6.16:
http://bugzilla.kernel.org/show_bug.cgi?id=6356
(sbp2: scsi_add_device failed. IEEE1394 HD is not working anymore.)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: Vanei Heidemann <linux@javanei.com.br>
Tested-by: Martin Putzlocher <mputzi@gmx.de> (chip type unconfirmed)
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In case the blacklist with workarounds for device bugs yields a false
positive, the module load parameter can now also be used as an override
instead of an addition to the blacklist.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Apple decided to copy some USB stupidity over to FireWire.
The sector number returned by iPods from read_capacity is one too many.
This may cause I/O errors, especially if the kernel is configured for EFI
partition support. We use the same workaround as usb-storage but have to
check for different model IDs.
http://marc.theaimsgroup.com/?t=114233262300001https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=187409
Acknowledgements:
Diagnosis and therapy by Mathieu Chouquet-Stringer <ml2news@free.fr>,
additional data about affected and unaffected Apple hardware from
Vladimir Kotal, Sander De Graaf, Bryan Olmstead and Hugh Dixon.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Grand unification of the three types of workarounds we have so far.
The "skip mode page 8" workaround is now limited to devices which
pretend to be of TYPE_DISK instead of TYPE_RBC. This workaround is no
longer enabled for Initio bridges.
Patch update in anticipation of more workarounds:
- Add module parameter "workarounds".
- Deprecate parameter "force_inquiry_hack".
- Compose the blacklist of a compound type for better readability and
extensibility.
- Remove a now unused #define.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/shemminger/netdev-2.6:
sky2: prevent dual port receiver problems
x86_64: Check for bad dma address in b44 1GB DMA workaround
The ixp2000 driver for the enp2611 was developed on a board with
When flushing out queued commands after a successful device reset,
make sure that SRP completes the right commands, instead of calling
scsi_done on the command passed into the device reset handler over and
over.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a reconnection attempt fails, then SRP does two scsi_host_put()s.
This is a historical relic from an earlier version of the driver that
took a reference on the scsi_host before trying to reconnect, so get
rid of the extra scsi_host_put().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Sending a DREQ may fail, for example because the remote target has
already broken the connection. If so, then SRP should not wait for
the disconnection to complete, because it never will.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Setting fw_cmd_doorbell allows FW command to be queued using posted
writes instead of requiring polling on a "go" bit, so it should be a
performance boost. However, the option causes problems with at least
some device/firmware combinations, so set the default to 0 until we
understand what's going on better.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This fixes two problems triggered by the MMC stack updating clocks:
- SPI masters driver should accept a max clock speed of zero; that's one
convention for marking idle devices. (Presumably that helps controllers
that don't autogate clocks to "off" when not in use.)
- There are more than 1000 nanoseconds per millisecond; setting the clock
down to 125 KHz now works properly.
Showing once again that Zero (http://en.wikipedia.org/wiki/Zero) is still
an inexhaustible number of bugs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix two outstanding issues with the pxa2xx_spi driver:
1) Bad cast in the function u32_writer. Thanks to Henrik Bechmann
2) Adds support for per transfer changes to speed and bits per word
Signed-off-by: Stephen Street <stephen@streetfiresound.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to be able to have a "SPI bus 0" matching chip numbering; but
that number was wrongly used to flag dynamic allocation of a bus number.
This patch resolves that issue; now negative numbers trigger dynamic alloc.
It also updates the how-to-write-a-controller-driver overview to mention
this stuff.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add spi_device hook for LSB-first word encoding, and update all the
(in-tree) controller drivers to reject such devices. Eventually,
some controller drivers will be updated to support lsb-first encodings
on the wire; no current drivers need this.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Renamed bitbang_transfer_setup to follow convention of other exported symbols
from spi-bitbang. Exported spi_bitbang_setup_transfer to allow users of
spi-bitbang to use the function in their own setup_transfer.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure that spi_write_then_read() can always handle at least 32 bytes
of transfer (total, both directions), minimizing one portability issue.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver turns a PXA2xx synchronous serial port (SSP) into a SPI master
controller (see Documentation/spi/spi_summary). The driver has the following
features:
- Support for any PXA2xx SSP
- SSP PIO and SSP DMA data transfers.
- External and Internal (SSPFRM) chip selects.
- Per slave device (chip) configuration.
- Full suspend, freeze, resume support.
Signed-off-by: Stephen Street <stephen@streetfiresound.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some protocols (like one for some bitmap displays) require different clock
speed or word size settings for each transfer in an SPI message. This adds
those parameters to struct spi_transfer. They are to be used when they are
nonzero; otherwise the defaults from spi_device are to be used.
The patch also adds a setup_transfer callback to spi_bitbang, uses it for
messages that use those overrides, and implements it so that the pure
bitbanging code can help resolve any questions about how it should work.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Needed for interaction with the nommu code in x86-64 which
will return bad_dma_address if the address exceeds dma_mask.
Cc: netdev@vger.kernel.org
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Andrew Victor
The serial_core already manages the power state of the UARTs, and
therefore it shouldn't suspend a UART which was previously suspended.
This patch modifies serial_core only call the UART-specific
power-management function if the PM state is actually changing.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If the s3c2410 watchdog timer is not enabled by
the driver at startup, ensure that it is stopped
in-case the boot process has enabled it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Temporary remove support for ICH6 + ICH7. In these newer TCO's
the watchdog timer has changed: the TCO_TMR register is not at
the TCOBASE+0x1 offset, but changed it's place to TCOBASE+0x12
and became 10 bit long [0:9]. (Kernel BUG 6031).
ICH6 + ICH7 support will be added in a new driver. Code is
under test.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Fix printk output.
sc1200wdt: build 20020303<3>sc1200wdt: io parameter must be specified
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>
When both ports are receiving simultaneously, the receive logic gets confused
and may pass up a packet before it is full. This causes hangs, and IP will see
lots of garbage packets. There is even the potential for data corruption if
a later arriving packet DMA's into freed memory.
It looks like a hardware bug because status arrives for a packet but no
data is there. Until this bug is worked out, block the user from bringing
up both ports at once.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Needed for interaction with the nommu code in x86-64 which
will return bad_dma_address if the address exceeds dma_mask.
Cc: netdev@vger.kernel.org
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
three gigabit ports, but some enp2611 models only have two ports
(and only one onboard PM3386.) The current driver assumes there
are always three ports and so it doesn't work on the two-port
version of the board at all.
This patch adds a bit of logic to the enp2611 driver to limit the
number of ports to 2 if the second PM3386 isn't detected.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
On alpha:
drivers/net/dl2k.c: In function `rio_free_tx':
drivers/net/dl2k.c:768: error: `DMA_48BIT_MASK' undeclared (first use in this function)
drivers/net/dl2k.c:768: error: (Each undeclared identifier is reported only once
drivers/net/dl2k.c:768: error: for each function it appears in.)
drivers/net/dl2k.c: In function `receive_packet':
drivers/net/dl2k.c:896: error: `DMA_48BIT_MASK' undeclared (first use in this function)
drivers/net/dl2k.c: In function `rio_close':
drivers/net/dl2k.c:1803: error: `DMA_48BIT_MASK' undeclared (first use in this function)
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the IBM microdrive to the known PCMCIA IDs for ide_cs.
Signed-off-by: Thomas Kleffel <tk@maintech.de>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do not enable the SMBus device on Asus boards if suspend is used. We do
not reenable the device on resume, leading to all sorts of undesirable
effects, the worst being a total fan failure after resume on Samsung P35
laptop.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/char/tpm/tpm.c: In function 'tpm_register_hardware':
drivers/char/tpm/tpm.c:1157: warning: assignment from incompatible pointer type
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Acked-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
