I'm surprised nobody complained about these before. What a waste.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we now use sdata pointers most of the time, using a netdev
pointer here is somewhat artificial, use an sdata pointer instead.
Replace a netdev-prefix in a few messages by a wiphy-prefix.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reorders the mlme code a bit so we don't need all the forward
function declarations. It also removes the ERP_INFO_USE_PROTECTION
define that is unused, but otherwise contains no real changes.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During testing of the disassociation fixes, Tomas noticed that it
was possible to run into a situation where you'd suddenly get a
few "wlan0: dropped frame to <AP> (unauthorized port)" messages
and I found this to be due to the AP's sta_info having been
removed but netif_carrier_off not having removed/stopped traffic
yet. To avoid that, stop the queue for the interface (and avoid
bringing them up when another vif scans when they weren't up.)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves disassociation code from ieee80211_set_associated
to ieee80211_set_disassoc. To reduce code duplication, it introduces
the ieee80211_sta_send_apinfo function. Additionally, it fixes a lapse
where BSS_CHANGED_HT wasn't set when notifying the driver of changes
due to disassociation.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes the MLME cleanly disassociate from the current BSS
when leaving it for a new one. This is not just nicer to the old AP
(we're leaving it, might as well tell it!) but also required for some
drivers that keep track of the station we're associated with, they'd
get confused because they'd think we are associated with two APs.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch restructure the flow of disassociation and deauthentication
flows to be consistent under all circumstances.
It ensures that BA session is treated down before deauthentication or disassociation,
adds the removal of the obsolete sta form station table and fixes a related bug (sta_info_destroy
without sta_info_unlink) in ieee80211_associated()
and reduce some code duplication
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since IE parsing is required for the mlme and mesh code, it's
not a static function anyway, and it's much better to have it
in util rather than the overly large mlme.c
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This says chan_switch.action_code but really means
measurement.action_code, of course the actual offset in
the frame is the same, it's just harder to understand
this way.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The action frame length checks are one too small, there's not just
an action code as the comment makes you believe, there's a category
code too, and the category code is required in each action frame
(hence part of IEEE80211_MIN_ACTION_SIZE).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we receive information about a BSS we check at some point
whether or not we think we're allowed to use the channel it is
on, but we do that fairly late. I don't think we should do it
that late, so do it earlier to avoid doing IBSS/mesh stuff on
that channel and then getting confused because it's disabled.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The conf_tx callback currently needs to be atomic, this requirement
is just because it can be called from scanning. This rearranges it
slightly to only update while not scanning (which is fine, we'll be
getting beacons when associated) and thus removes the atomic
requirement.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The if itself doesn't need to be protected, so move in the RCU
locking to avoid doing anything at all when the condition isn't
true.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch follows 11n spec naming more rigorously replacing MIMO_PS
with SM_PS (Spatial Multiplexing Power Save).
(Originally submitted as 4 patches, "mac80211: change MIMO_PS to SM_PS",
"iwlwifi: change MIMO_PS to SM_PS", "ath9k: change MIMO_PS to SM_PS",
and "iwlwifi: remove double definition of SM PS". -- JWL)
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix mac80211 kernel-doc missing struct field:
Warning(linux-2.6.27-rc1-git2//net/mac80211/sta_info.h:329): No description found for parameter 'tid_seq[IEEE80211_QOS_CTL_TID_MASK + 1]'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch address some IBSS rate issues introduced or not covered
by "mac80211: eliminate IBSS warning in rate_lowest_index()" and
"cfg80211 API for channels/bitrates, mac80211 and driver conversion".
This patch:
1. Moves addition of IBSS station from
prepare_for_handlers to ieee80211_rx_bss_info when triggered from beacon
eliminating bogus supported rates.
2. Initialize properly supported rates also in IBSS merging
3. Ensure that mandatory rates are always added into supported
rates. This is needed in case when station addition is triggered from
non beacon/probe packet. Some management frames need to be sent
4. Remove initialization of supported rates from self rates. This path
was dead code after 6bc37c06bc4 and in general incorrect.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Cc: Vladimir Koutny <vlado@work.ksp.sk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes regression in iwlwifi IBSS rate scaling caused by patch:
commit 6bc37c06bc424bcf3f944e6a79e2d5bb537e02ed
Author: Vladimir Koutny <vlado@work.ksp.sk>
Date: Fri Jun 13 16:50:44 2008 +0200
mac80211: eliminate IBSS warning in rate_lowest_index()
An IBSS station is added in prepare_for_handlers where the rate scaling was
initialized only with single rate matching the received packet.
The correct rate scale information should be updated only in
ieee80211_rx_bss_info function where beacon is parsed. Because
of coding error the rate info was left untouched.
If a beacon has triggered the connection the rate remined 1Mbps.
This patch fixes this coding error
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Cc: Vladimir Koutny <vlado@work.ksp.sk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is obviously good for userspace to know up front which
interface modes a given piece of hardware might support (even
if adding such an interface might fail later because of
concurrency issues), so let's make cfg80211 aware of that.
For good measure, disallow adding interfaces in all other
modes so drivers don't forget to announce support for one mode
when they add it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 087d833e5a, which was
reported to break wireless at least in some combinations with 32bit user
space and a 64bit kernel. Alex Williamnson bisected it to this commit.
Reported-and-bisected-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Cc: David Miller <davem@davemloft.net>
Cc: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
debugfs union in struct ieee80211_sub_if_data is misused by including a
common default_key dentry as a union member. This ends occupying the same
memory area with the first dentry in other union members (structures;
usually drop_unencrypted). Consequently, debugfs operations on
default_key symlinks and drop_unencrypted entry are using the same
dentry pointer even though they are supposed to be separate ones. This
can lead to removing entries incorrectly or potentially leaving
something behind since one of the dentry pointers gets lost.
Fix this by moving the default_key dentry to a new struct
(common_debugfs) that contains dentries (more to be added in future)
that are shared by all vif types. The debugfs union must only be used
for vif type-specific entries to avoid this type of pointer corruption.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace (e.g., hostapd) to set HT capabilities for associated
STAs. This is based on a patch from Zhu Yi <yi.zhu@intel.com> (only
the NL80211_ATTR_HT_CAPABILITY for NEW_STA part is included here).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bit 4-5 of DSCP should not be considered by classify_d1. The
802.11 QoS Priority field is only depending on the precedence level.
Signed-off-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean up and extend scan result processing by storing all the IEs from
Beacon/Probe Response frames in a single block instead of allocating
memory for each specific IE separately. This removes lot of unnecessary
code and automatically supports reporting of new IEs (e.g., IEEE
802.11r) into user space without need to manually extend mac80211
scanning code whenever a new protocol adds IE(s).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change adds a new cfg80211 command, NL80211_CMD_SET_BSS, to allow
AP mode BSS parameters to be changed from user space (e.g., hostapd).
The drivers using mac80211 are expected to be modified with separate
changes to use the new BSS info parameter for short slot time in the
bss_info_changed() handler.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otherwise, drivers are required to keep track of the sequence numbers
themselves, and they really shouldn't be since we already do it for
them. I'll fix the race once we figure out how this code should work
at all, it's currently disabled.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The association request includes a list of supported data rates.
802.11b: 4 supported rates.
802.11g: 12 (8 + 4) supported rates.
802.11a: 8 supported rates.
The rates tag of the assoc request has room for only 8 rates. In case of
802.11g an extended rate tag is appended. However in net/wireless/mlme.c
an extended (empty) rate tag is also appended if the number of rates is
exact 8. This empty (length=0) extended rates tag causes some APs to
deny association with code 18 (unsupported rates). These APs include my
ZyXEL G-570U, and according to Tomas Winkler som Cisco APs.
'If count == 8' has been used to check for the need for an extended rates
tag. But count would also be equal to 8 if the for loop exited because of
no more supported rates. Therefore a check for count being less than
rates_len would seem more correct.
Thanks to:
* Dan Williams for newbie guidance
* Tomas Winkler for confirming the problem
Signed-off-by: Jan-Espen Pettersen <sigsegv@radiotube.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previous version was using incorrect union structures for non-AP
interfaces when adding and removing max_ratectrl_rateidx and
force_unicast_rateidx entries. Depending on the vif type, this ended
up in corrupting debugfs entries since the dentries inside different
union structures ended up going being on top of eachother.. As the
end result, debugfs files were being left behind with references to
freed data (instant kernel oops on access) and directories were not
removed properly when unloading mac80211 drivers. This patch fixes
those issues by using only a single union structure based on the vif
type.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the function mesh_table_grow, it is the new table not the argument table
that should be freed if the function fails (cf commit
bd9b448f4c)
The semantic match that detects this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
expression E,f;
position p1,p2,p3;
identifier l;
statement S;
@@
x = mesh_table_alloc@p1(...)
...
if (x == NULL) S
... when != E = x
when != mesh_table_free(x)
goto@p2 l;
... when != E = x
when != f(...,x,...)
when any
(
return \(0\|x\);
|
return@p3 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
p3 << r.p3;
@@
print "%s: call on line %s not freed or saved before return on line %s via line %s" % (p1[0].file,p1[0].line,p3[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous code was using IWEVCUSTOM to report IEs from AssocReq and
AssocResp frames into user space. This can easily hit the 256 byte
limit (IW_CUSTOM_MAX) with APs that include number of vendor IEs in
AssocResp. This results in the event message not being sent and dmesg
showing "wlan0 (WE) : Wireless Event too big (366)" type of errors.
Convert mac80211 to use IWEVASSOCREQIE/IWEVASSOCRESPIE to avoid the
issue of being unable to send association IEs as wireless events. These
newer event types use binary encoding and larger maximum size
(IW_GENERIC_IE_MAX = 1024), so the likelyhood of not being able to send
the IEs is much smaller than with IWEVCUSTOM. As an extra benefit, the
code is also quite a bit simpler since there is no need to allocate an
extra buffer for hex encoding.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a direct probe request as first step in the association
flow if data we have is not up to date. Motivation of this step is to make
sure that the bss information we have is correct, since last scan could
have been done a while ago, and beacons do not fully answer this need as
there are potential differences between them and probe responses (e.g.
WMM parameter element)
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes noticed problem in noisy environments of 50+ APs
that scan fails to find the requested AP on first try, which
leads to connection refusal. second scan has empirically proven to fix
this problem in almost all cases.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Esti Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch move add STA_MLME to station mlme state defines.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves filtering statement from ieee80211_rx_bss_info
which is called for both beacon and probe to ieee80211_rx_mgmt_probe_resp
and save few cycles in beacon parsing.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces net_device arguments to mac80211 internal functions
with ieee80211_{local,sub_if_data} as appropriate.
It also does the same for many 802.11s mesh functions, and changes the
mesh path table to be indexed on sub_if_data rather than net_device.
If the mesh part needs to be a separate patch let me know, but since
mesh uses a lot of mac80211 functions which were being converted anyway,
the changes go hand-in-hand somewhat.
This patch probably does not convert all the functions which could be
converted, but it is a large chunk and followup patches will be
provided.
Signed-off-by: Jasper Bryant-Greene <jasper@amiton.co.nz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ETH_P_PAE belongs in if_ether.h with the other ETH_P_* definitions. This
patch moves it there.
Signed-off-by: Jasper Bryant-Greene <jasper@amiton.co.nz>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Originally by Johannes Berg. This patch adds support for devices that do not
report their MAC address until the firmware is loaded. While the address is not
known, a multicast on is used.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the last users of the rx/tx_data->fc data members and use the
le16 frame_control from the header directly.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All users have been moved over to the version taking a le16 frame control
rather than a cpu-endian value.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Those functions that still use ieee80211_get_hdrlen are moved over
to use the little endian frame control.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
linux/ieee80211.h now has IEEE80211_QOS_CTL_LEN for this purpose.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_get_hdrlen_from_skb internally checks the skb is long enough to
hold the full ieee80211_hdr, else it returns zero. Use ieee80211_hdrlen
which always returns the hdrlen and check the remaining room in the
skb explicitly when removing encryption headers or the qos control field.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
use the rates ERP flag to derive CCK or OFDM modulation for the radiotap
header.
(it might be more correct to get this information from the hardware itself, but it
seems safe to assume this in most practical cases.)
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
