gcc 4.4 warns about:
drivers/parisc/lba_pci.c: In function 'lba_pat_resources':
drivers/parisc/lba_pci.c:1099: warning: the frame size of 8280 bytes is larger than 4096 bytes
The problem is we declare two large structures on the stack. They don't need
to be on the stack since they are only used during LBA initialization (which
is serialized). Moving to be "static".
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
The defines and typedefs (hw_interrupt_type, no_irq_type, irq_desc_t) have
been kept around for migration reasons. After more than two years it's
time to remove them finally.
This patch cleans up one of the remaining users. When all such patches
hit mainline we can remove the defines and typedefs finally.
Impact: cleanup
Convert the last remaining users to struct irq_chip and remove the
define.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Fix miscompilation in arch/parisc/kernel/irq.c:
123: warning: passing arg 1 of `cpumask_setall' from incompatible pointer type
141: warning: passing arg 1 of `cpumask_copy' from incompatible pointer type
300: warning: passing arg 1 of `cpumask_copy' from incompatible pointer type
357: warning: passing arg 2 of `cpumask_copy' from incompatible pointer type
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Alex Chiang asked me why PARISC was calling pci_bus_add_devices()
and pci_bus_assign_resources() in the opposite order from everyone else.
No reason and I couldn't see any data dependency.
Patch below applies cleanly to 2.6.30-rc2.
Later, I suspected the code worked only because no drivers would be
loaded/ready until much later in the system initialization sequence.
Tested "LBA" code on J6000 (32-bit) and A500 (64-bit SMP) with 2.6.30-rc2.
Not tested with any Dino controllers.
Not tested with PCI-PCI Bridge (TBD).
Reported-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
There are two reasons to expose the memory *a in the asm:
1) To prevent the compiler from discarding a preceeding write to *a, and
2) to prevent it from caching *a in a register over the asm.
The change has had a few days testing with a SMP build of 2.6.22.19
running on a rp3440.
This patch is about the correctness of the __ldcw() macro itself.
The use of the macro should be confined to small inline functions
to try to limit the effect of clobbering memory on GCC's optimization
of loads and stores.
Signed-off-by: Dave Anglin <dave.anglin@nrc-cnrc.gc.ca>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Doing an IPI with local interrupts off triggers a warning. We
don't need to be quite so ridiculously paranoid. Also, clean up
a bit of the code a little.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
The atomic operations on parisc are defined as macros. The macros
includes casts which disallows the use of some syntax elements and
produces error like this:
net/phonet/pep.c: In function 'pipe_rcv_status':
net/phonet/pep.c:262: error: lvalue required as left operand of assignment
The patch removes this superfluous casts.
Signed-off-by: Bastian Blank <waldi@debian.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Fix this build error when CONFIG_PROC_FS is not set:
drivers/parisc/ccio-dma.c:1574: error: 'ccio_proc_info_fops' undeclared
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Fix this build error when CONFIG_STI_CONSOLE is not set
drivers/video/stifb.c:1337: undefined reference to `sti_get_rom'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: fix error message formatting
Btrfs: fix use after free in btrfs_start_workers fail path
Btrfs: honor nodatacow/sum mount options for new files
Btrfs: update backrefs while dropping snapshot
Btrfs: account for space we may use in fallocate
Btrfs: fix the file clone ioctl for preallocated extents
Btrfs: don't log the inode in file_write while growing the file
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] cxgb3i: fix connection error when vlan is enabled
[SCSI] FC transport: Locking fix for common-code FC pass-through patch
[SCSI] zalon: fix oops on attach failure
[SCSI] fnic: use DMA_BIT_MASK(nn) instead of deprecated DMA_nnBIT_MASK
[SCSI] fnic: remove redundant BUG_ONs and fix checks on unsigned
[SCSI] ibmvscsi: Fix module load hang
* git://git.infradead.org/iommu-2.6: (38 commits)
intel-iommu: Don't keep freeing page zero in dma_pte_free_pagetable()
intel-iommu: Introduce first_pte_in_page() to simplify PTE-setting loops
intel-iommu: Use cmpxchg64_local() for setting PTEs
intel-iommu: Warn about unmatched unmap requests
intel-iommu: Kill superfluous mapping_lock
intel-iommu: Ensure that PTE writes are 64-bit atomic, even on i386
intel-iommu: Make iommu=pt work on i386 too
intel-iommu: Performance improvement for dma_pte_free_pagetable()
intel-iommu: Don't free too much in dma_pte_free_pagetable()
intel-iommu: dump mappings but don't die on pte already set
intel-iommu: Combine domain_pfn_mapping() and domain_sg_mapping()
intel-iommu: Introduce domain_sg_mapping() to speed up intel_map_sg()
intel-iommu: Simplify __intel_alloc_iova()
intel-iommu: Performance improvement for domain_pfn_mapping()
intel-iommu: Performance improvement for dma_pte_clear_range()
intel-iommu: Clean up iommu_domain_identity_map()
intel-iommu: Remove last use of PHYSICAL_PAGE_MASK, for reserving PCI BARs
intel-iommu: Make iommu_flush_iotlb_psi() take pfn as argument
intel-iommu: Change aligned_size() to aligned_nrpages()
intel-iommu: Clean up intel_map_sg(), remove domain_page_mapping()
...
It is not safe to use match_int without checking the token type returned
by match_token (especially when the token type returned is Opt_err and
args is empty). Fix it.
Signed-off-by: Abhishek Kulkarni <adkulkar@umail.iu.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds ETH_P_1588 protocol ID define.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY_HALTED state disables phydev->link, but the link will not be
updated upon entering PHY_RESUMING. Add a call to phy_read_status() to
update the link before entering PHY_RUNNING. If the link is not up at
this point, enter the PHY_NOLINK state instead.
Also, when transitioning from PHY_RESUMING to PHY_RUNNING, calls to
netif_carrier_on() and phydev->adjust_link() are missing. Add the calls
similar to the other transitions to PHY_RUNNING.
Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restrict firmware reset to following cases -
o chip rev is NX2031 (firmare doesn't support heartbit).
o firmware is dead.
o previous attempt to init firmware had failed.
o we have got newer file firmware.
This speeds up module load tremendously (by upto 8 sec),
also avoids downtime for NCSI (management) pass-thru
traffic.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct firmware encoding is 8 bit major, 8 bit minor and
16 bit subversion. Flash has sizes rightly set, but original
driver submission messed it leaving 16 bit major and 8 bit
subversion.
Also fix a infinite loop when cut-thru file firmware is
invalid.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop a sanity check which doesn't serve any useful purpose anymore.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
ISDN connection setup failed if the "connection active" and
"B channel up" messages from the device arrived in a different
order than expected. Modify the state machine to accept them in
any order.
Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
CC: stable <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix hang with HIGHMEM_64G and 32bit resource. According to hpa and
Linus, use (resource_size_t)-1 to fend off big ranges.
Analyzed by hpa
Reported-and-tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These macros had two bugs:
- the type of the mask was not correctly expanded to the full size of
the argument being expanded, resulting in possible loss of high bits
when mixing types.
- the alignment argument was evaluated twice, despite the macro looking
like a fancy function (but it really does need to be a macro, since
it works on arbitrary integer types)
Noticed by Peter Anvin, and with a fix that is a modification of his
suggestion (bug noticed by Yinghai Lu).
Cc: Peter Anvin <hpa@zytor.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make an error msg look nicer by inserting a space between number and word.
Signed-off-by: Hu Tao <hu.taoo@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
worker memory is already freed on one fail path in btrfs_start_workers,
but is still dereferenced. Switch the dereference and kfree.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The btrfs attr patches unconditionally inherited the inode flags field
without honoring nodatacow and nodatasum. This fix makes sure
we properly record the nodatacow/sum mount options in new inodes.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The new backref format has restriction on type of backref item. If a tree
block isn't referenced by its owner tree, full backrefs must be used for the
pointers in it. When a tree block loses its owner tree's reference, backrefs
for the pointers in it should be updated to full backrefs. Current
btrfs_drop_snapshot misses the code that updates backrefs, so it's unsafe for
general use.
This patch adds backrefs update code to btrfs_drop_snapshot. It isn't a
problem in the restricted form btrfs_drop_snapshot is used today, but for
general snapshot deletion this update is required.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Using Eric Sandeen's xfstest for fallocate, you can easily trigger a ENOSPC
panic on btrfs. This is because we do not account for data we may use when
doing the fallocate. This patch fixes the problem by properly reserving space,
and then just freeing it when we are done. The reservation stuff was made with
delalloc in mind, so its a little crude for this case, but it keeps the box
from panicing.
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The per-user inotify_devs value is incremented each time a new file is
allocated, but never decremented. This led to inotify_init failing after a
limited number of calls.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Check dma_pte_present() and only free the page if there _is_ one.
Kind of surprising that there was no warning about this.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
On Wed, 2009-07-01 at 16:59 -0700, Linus Torvalds wrote:
> I also _really_ hate how you do
>
> (unsigned long)pte >> VTD_PAGE_SHIFT ==
> (unsigned long)first_pte >> VTD_PAGE_SHIFT
Kill this, in favour of just looking to see if the incremented pte
pointer has 'wrapped' onto the next page. Which means we have to check
it _after_ incrementing it, not before.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The sound device instance needs to be a child of the USB interface, not
the USB device. Newer udev versions pay attention to that.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Reported-by: Lennart Poettering <lennart@poettering.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When resuming, we better take the DACs out of the reset state before
trying to use them.
Reference: kernel bug #13599http://bugzilla.kernel.org/show_bug.cgi?id=13599
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add basic performance counter support to the FRV arch.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This would have found the bug in i386 pci_unmap_addr() a long time ago.
We shouldn't just silently return without doing anything.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: LCDC dcache flush for deferred io
sh: Fix compiler error and include the definition of IS_ERR_VALUE
sh: re-add LCDC fbdev support to the Migo-R defconfig
sh: fix se7724 ceu names
sh: ms7724se: Enable sh_eth in defconfig.
arch/sh/boards/mach-se/7206/io.c: Remove unnecessary semicolons
sh: ms7724se: Add sh_eth support
nommu: provide follow_pfn().
sh: Kill off unused DEBUG_BOOTMEM symbol.
perf_counter tools: add cpu_relax()/rmb() definitions for sh.
sh64: Hook up page fault events for software perf counters.
sh: Hook up page fault events for software perf counters.
sh: make set_perf_counter_pending() static inline.
clocksource: sh_tmu: Make undefined TCOR behaviour less undefined.
Since we're using cmpxchg64() anyway (because that's the only way to do
an atomic 64-bit store on i386), we might as well ditch the extra
locking and just use cmpxchg64() to ensure that we don't add the page
twice.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since writenotify on uncached vmas is unsupported in 2.6.31,
live with cached framebuffer memory in the deferred io
case for now and flush the dcache before forcing refresh.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Magnus damm <damm@igel.co.jp>