Add new SERDES tuning to aid manufacturing.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Reset the list pointers after freeing the SDMA packet list. This is
done to any potential double-free cases.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Implement new SERDES initialization routine and improvements to signal
integrity -- disable LE1 adaptation, disable LOS after link-up, set
better SERDES parameters.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If these flags are set when the QP is transitioned to the error state,
it will wait until the flags are cleared, which may never happen if
the error transition is due to a link going down.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The driver was incorrectly choosing HCAs on which to allocate new user
contexts based on overall count of usable ports regardless whether the
usable port was on the currently selected HCA.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add check when setting configured contexts that the value does not
exceed the number of contexts allocated for the card. If the value
exceeds the already allocated count, set it to what is already
allocated.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the link transitions from ACTIVE_DEFERRED to ACTIVE, the driver
only sees the ACTIVE state. With this change, it will check whether
the state was already ACTIVE and if so, it will not generated IB
events and will not clear symbol error counts.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code to generate receive completion entries for UD send with
immediate contains the wrong payload length. This is because when the
code to compute the payload size was moved, the value of hdrsize
didn't get moved too. The fix is to update tlen directly.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IBTA vol. 1 release 1.2.1 spec. says:
C14-24.2.1: If PortInfo:Portstate=Down, then a SubnSet(PortInfo) shall
make any changes it specifies to PortInfo:PortPhysicalState; any other
result is vendor-dependent.
The patch changes the error handling so that the reply says there are
invalid fields but still attempts to set fields that are in range
including PortInfo:PortPhysicalState.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
According to IBTA vol. 1, C11-30.1.1, a notification callback is
invoked if the CQ is armed for the next solicited completion event or
an error completion. The error case wasn't being generated correctly.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support to recognize another board variation named QME7362.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The receive header queue sizes need to modified for performance
tuning. Three module parameters are added to support this.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In ib_uverbs_poll_cq() code there is a potential integer overflow if
userspace passes in a large cmd.ne. The calls to kmalloc() would
allocate smaller buffers than intended, leading to memory corruption.
There iss also an information leak if resp wasn't all used.
Unprivileged userspace may call this function, although only if an
RDMA device that uses this function is present.
Fix this by copying CQ entries one at a time, which avoids the
allocation entirely, and also by moving this copying into a function
that makes sure to initialize all memory copied to userspace.
Special thanks to Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
for his help and advice.
Cc: <stable@kernel.org>
Signed-off-by: Dan Carpenter <error27@gmail.com>
[ Monkey around with things a bit to avoid bad code generation by gcc
when designated initializers are used. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB: Fix information leak in marshalling code
IB/pack: Remove some unused code added by the IBoE patches
IB/mlx4: Fix IBoE link state
IB/mlx4: Fix IBoE reported link rate
mlx4_core: Workaround firmware bug in query dev cap
IB/mlx4: Fix memory ordering of VLAN insertion control bits
MAINTAINERS: Update NetEffect entry
ib_ucm_init_qp_attr() and ucma_init_qp_attr() pass struct ib_uverbs_qp_attr
with reserved, qp_state, {ah_attr,alt_ah_attr}{reserved,->grh.reserved}
fields uninitialized to copy_to_user(). This leads to leaking of
contents of kernel stack memory to userspace.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use netif_running() and netif_carrier_ok() to report link state,
exactly as is done to report Ethernet link state in sysfs.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The link rate is the product of the link speed in the link width. For
Etherent ports the rate is 10G, so we use 1 for the width and 4 for
speed to get the correct rate.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We must fully update the control segment before marking it as valid,
so that hardware doesn't start executing it before we're ready.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
[ Move VLAN control bit setting to before wmb(). - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The big kernel lock has been removed from all these files at some point,
leaving only the #include.
Remove this too as a cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.
The patch below presents a simple SCSI host lock push-down as an
equivalent transformation. No locking or other behavior should change
with this patch. All existing bugs and locking orders are preserved.
Additionally, add one parameter to queuecommand,
struct Scsi_Host *
and remove one parameter from queuecommand,
void (*done)(struct scsi_cmnd *)
Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.
Minimal code disturbance was attempted with this change. Most drivers
needed only two one-line modifications for their host lock push-down.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (52 commits)
split invalidate_inodes()
fs: skip I_FREEING inodes in writeback_sb_inodes
fs: fold invalidate_list into invalidate_inodes
fs: do not drop inode_lock in dispose_list
fs: inode split IO and LRU lists
fs: switch bdev inode bdi's correctly
fs: fix buffer invalidation in invalidate_list
fsnotify: use dget_parent
smbfs: use dget_parent
exportfs: use dget_parent
fs: use RCU read side protection in d_validate
fs: clean up dentry lru modification
fs: split __shrink_dcache_sb
fs: improve DCACHE_REFERENCED usage
fs: use percpu counter for nr_dentry and nr_dentry_unused
fs: simplify __d_free
fs: take dcache_lock inside __d_path
fs: do not assign default i_ino in new_inode
fs: introduce a per-cpu last_ino allocator
new helper: ihold()
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (63 commits)
IB/qib: clean up properly if pci_set_consistent_dma_mask() fails
IB/qib: Allow driver to load if PCIe AER fails
IB/qib: Fix uninitialized pointer if CONFIG_PCI_MSI not set
IB/qib: Fix extra log level in qib_early_err()
RDMA/cxgb4: Remove unnecessary KERN_<level> use
RDMA/cxgb3: Remove unnecessary KERN_<level> use
IB/core: Add link layer type information to sysfs
IB/mlx4: Add VLAN support for IBoE
IB/core: Add VLAN support for IBoE
IB/mlx4: Add support for IBoE
mlx4_en: Change multicast promiscuous mode to support IBoE
mlx4_core: Update data structures and constants for IBoE
mlx4_core: Allow protocol drivers to find corresponding interfaces
IB/uverbs: Return link layer type to userspace for query port operation
IB/srp: Sync buffer before posting send
IB/srp: Use list_first_entry()
IB/srp: Reduce number of BUSY conditions
IB/srp: Eliminate two forward declarations
IB/mlx4: Signal node desc changes to SM by using FW to generate trap 144
IB: Replace EXTRA_CFLAGS with ccflags-y
...
Use the new {max,min}3 macros to save some cycles and bytes on the stack.
This patch substitutes trivial nested macros with their counterpart.
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Joe Perches <joe@perches.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean up properly if pci_set_consistent_dma_mask() fails.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some PCIe root complex chip sets don't support advanced error reporting.
Allow the driver to load OK if pci_enable_pcie_error_reporting() fails.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If CONFIG_PCI_MSI is not set, and a QLE7140 is present, the pointer
"dd" is uninitialized.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Noticed this odd looking thing in dmesg:
ib_qib 0000:02:00.0: <3>ib_qib: Unable to enable pcie error reporting: -5
which is due to a bad use of dev_info.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Instead of always assigning an increasing inode number in new_inode
move the call to assign it into those callers that actually need it.
For now callers that need it is estimated conservatively, that is
the call is added to all filesystems that do not assign an i_ino
by themselves. For a few more filesystems we can avoid assigning
any inode number given that they aren't user visible, and for others
it could be done lazily when an inode number is actually needed,
but that's left for later patches.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Since an IB transport port may use either IB or Ethernet as its link layer,
add the file /sys/class/infiniband/<device>/ports/<port_num>/link_layer to
show the link layer for the port.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch allows IBoE traffic to be encapsulated in 802.1Q tagged
VLAN frames. The VLAN tag is encoded in the GID and derived from it
by a simple computation.
The netdev notifier callback is modified to catch VLAN device
addition/removal and the port's GID table is updated to reflect the
change, so that for each netdevice there is an entry in the GID table.
When the port's GID table is exhausted, GID entries will not be added.
Only children of the main interfaces can add to the GID table; if a
VLAN interface is added on another VLAN interface (e.g. "vconfig add
eth2.6 8"), then that interfaces will not add an entry to the GID
table.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add 802.1q VLAN support to IBoE. The VLAN tag is encoded within the
GID derived from a link local address in the following way:
GID[11] GID[12] contain the VLAN ID when the GID contains a VLAN.
The 3 bits user priority field of the packets are identical to the 3
bits of the SL.
In case of rdma_cm apps, the TOS field is used to generate the SL
field by doing a shift right of 5 bits effectively taking to 3 MS bits
of the TOS field.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for IBoE to mlx4_ib. The bulk of the code is handling the
new address vector fields; mlx4 needs the MAC address of a remote node
to include it in a WQE (for datagrams) or in the QP context (for
connected QPs). Address resolution is done by assuming all unicast
GIDs are either link-local IPv6 addresses.
Multicast group attach/detach needs to update the NIC's multicast
filters; but since attaching a QP to a multicast group can be done
before the QP is bound to a port, for IBoE we need to keep track of
all multicast groups that a QP is attached too before it transitions
from INIT to RTR (since it does not have a port in the INIT state).
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
[ Many things cleaned up and otherwise monkeyed with; hope I didn't
introduce too many bugs. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
srp_send_tsk_mgmt() was missing the proper DMA sync calls before posting
the buffer to the device.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use the list_first_entry() macro in ib_srp instead of open-coding the equivalent,
which makes the source code slightly more descriptive. The list_first_entry()
macro itself was introduced in kernel 2.6.22.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
As proposed by the SRP (draft) standard, ib_srp reserves one ring
element for SRP_TSK_MGMT requests. This patch makes sure that the SCSI
mid-layer never tries to queue more than (SRP request limit) - 1 SCSI
commands to ib_srp. This improves performance for targets whose request
limit is less than or equal to SRP_NORMAL_REQ_SQ_SIZE by reducing the
number of BUSY responses reported by ib_srp to the SCSI mid-layer.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The Node Description cannot be changed via MADs (it is read-only).
Until now, it was changed in the driver via sysfs, and the new Node
Description was simply inserted by the driver into MAD responses
(replacing the description returned by FW).
System startup scripts use the sysfs interface to change the node
description at driver startup to show the hostname, etc. However, this
has a race condition: the SM could discover the original FW node
description rather than the system-specific description if it queried the
port before the startup scripts finish running.
For mlx4, we fix this with a new FW command (SET_NODE) that allows
passing the new node description to FW. When this command is invoked,
FW sends a trap 144 to the SM. When it gets this trap, the SM can
query the node to obtain the new node description -- thus eliminating
the effects of the race.
This patch simply calls SET_NODE command when a new node description
is entered via sysfs (thus causing trap 144 to be issued by the FW).
We ignore all failures of the SET_NODE command (including those caused
by using a device FW that predates the SET_NODE command), since in
that case things work just as before.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For iWARP connections, the connect request is carried in a TCP payload
on an already established TCP connection. So if the ucma's backlog is
full, the connection request is transmitted and acked at the TCP level
by the time the connect request gets dropped in the ucma. The end
result is the connection gets rejected by the iWARP provider.
Further, a 32 node 256NP OpenMPI job will generate > 128 connect
requests on some ranks.
This patch increases the default max backlog to 1024, and adds a
sysctl variable so the backlog can be adjusted at run time.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use the net device's dev_id field to encode the port number of the pci
device. This can be used to to associate a net device with the pci
device's port. The encoding is: dev_id = port - 1.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1699 commits)
bnx2/bnx2x: Unsupported Ethtool operations should return -EINVAL.
vlan: Calling vlan_hwaccel_do_receive() is always valid.
tproxy: use the interface primary IP address as a default value for --on-ip
tproxy: added IPv6 support to the socket match
cxgb3: function namespace cleanup
tproxy: added IPv6 support to the TPROXY target
tproxy: added IPv6 socket lookup function to nf_tproxy_core
be2net: Changes to use only priority codes allowed by f/w
tproxy: allow non-local binds of IPv6 sockets if IP_TRANSPARENT is enabled
tproxy: added tproxy sockopt interface in the IPV6 layer
tproxy: added udp6_lib_lookup function
tproxy: added const specifiers to udp lookup functions
tproxy: split off ipv6 defragmentation to a separate module
l2tp: small cleanup
nf_nat: restrict ICMP translation for embedded header
can: mcp251x: fix generation of error frames
can: mcp251x: fix endless loop in interrupt handler if CANINTF_MERRF is set
can-raw: add msg_flags to distinguish local traffic
9p: client code cleanup
rds: make local functions/variables static
...
Fix up conflicts in net/core/dev.c, drivers/net/pcmcia/smc91c92_cs.c and
drivers/net/wireless/ath/ath9k/debug.c as per David
