Removing the higher number taps. Their usage was incorrect
and even if correct they should not be used for a touch screen.
_MT_ events should be used to communicate multiple fingers.
Signed-off-by: Rafi Rubin <rafi@seas.upenn.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Include TipSwitch in the touch detection decision for some single touch
firmwares. Confidence and InRange are high for all finger events
including those used to indicate the finger is no longer in contact with
the sensor.
Signed-off-by: Rafi Rubin <rafi@seas.upenn.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
I squelched TipSwitch in a recent patch which resulted in the loss
of Touch events for single touch firmwares. This patch just puts Touch back
in for single touch, and bundles it with DoubleTap (like the multitouch code).
The two events are used to convey the same message to different drivers.
Signed-off-by: Rafi Rubin <rafi@seas.upenn.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 6549981bc5 ("HID: fix N-trig touch panel with recent firmware")
adds a quirk that is needed for devices with more recent firmware so that
they become operational.
As it's not directly obvious from the code why is it needed, a comment
is worthwile.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
This reinstates the lost unpressing of BTN_TOUCH. To prevent undesireably
touch toggles this also deals with tip switch events.
Added a trap to prevent going out of bounds for hidinputs with empty reports.
Clear bits of unused buttons which result in misidentification.
Signed-off-by: Rafi Rubin <rafi@seas.upenn.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add DOUBLETAP to events emitted when in single touch only mode.
Users with a single touch firmware report not seeing the DOUBLETAP events; this
is a side effect of dropping old mapping for confidence. The confidence mapping
may be fine for singletouch mode but causes problems in multitouch mode.
Signed-off-by: Rafi Rubin <rafi@seas.upenn.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This cleans up the identification of multitouch groups and enables
the end of group sync.
Taps are now explicitly handled to adjust for the changes in the
event stream in multitouch mode. Added triple and quad tap for the
benefit of tools that recognize different tap types but do not have
full multi touch support.
This cleans up the behavior particularly for the latest firmware, which
didn't work particularly well with the older version of the driver.
In this form, when multitouch is active, both mt and st events will come out of
the "N-Trig MultiTouch" device. And when its not st events will come out of
"N-Trig Touchscreen".
Signed-off-by: Rafi Rubin <rafi@seas.upenn.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
With the pen and touch split apart, we no longer need to inject
additional tool switching events.
Signed-off-by: Rafi Rubin <rafi@seas.upenn.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added a quirk to enable distinct input devices. The digitizer utilizes
three inputs to represent pen, multitouch and a normal touch screen.
With the Pen partitioned, it behaves well and does not need special
handling.
Also, I set names to the input devices to clarify the functions of the
various inputs.
Signed-off-by: Rafi Rubin <rafi@seas.upenn.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Trivial patch which adds the __init and __exit macros to the module_init /
module_exit functions of several HID drivers from drivers/hid/
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When both touch and pen are active send a tool announcement before
sending any status changes so that event users may differentiate
which tool is changing.
Restored three usage codes used by the pen.
Signed-off-by: Rafi Rubin <rafi@seas.upenn.edu>
Acked-by: Stephane Chatty <chatty@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds support for multitouch interaction on the N-Trig touchscreen, using the
new ABS_MT_* input constants. Single touch support works as previously. This
code was tested against two versions of the N- Trig firmware: one that supports
dual pen/finger single touch, and one that supports finger multitouch but no
pen at all. Copyright notices that looked wrong were removed, as it seems that
there is only code written in 2009 by Rafin Rubin and Stephane Chatty in this
file.
Signed-off-by: Stephane Chatty <chatty@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This removal was scheduled and there is no problem with later
distros to adapt for the new bus, thanks to aliases.
module-init-tools map files are deprecated nowadays, so that
the patch which introduced hid ones into the m-i-t won't be
accepted and hence there is no reason for leaving compat stuff in.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
