Since "mac80211: make off-channel work generic" drivers have not been
notified of configuration changes after association or authentication. This
caused more dependence on current state to ensure driver will be notified
when configuration changes occur. One such problem arises if off-channel is
in progress when HT information changes. Since HT is only enabled on the
"oper_channel" the driver will never be notified of this change. Usually
the driver is notified soon after of a BSS information change
(BSS_CHANGED_HT) ... but since the driver did not get a notification that
this is a HT channel the new BSS information does not make sense.
Fix this by also changing the off-channel information when HT is enabled
and thus cause driver to be notified correctly.
This fixes a problem in 4965 when associated with 5GHz 40MHz channel.
Without this patch the system can associate but is unable to transfer any
data, not even ping.
See http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2158
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the addba timer expires but has no work to do,
it should not affect the state machine. If it does,
TX will not see the successfully established and we
can also crash trying to re-establish the session.
Cc: stable@kernel.org [2.6.32, 2.6.33]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The af_packet protocol is used by Perl to do ioctls as reported by
Stephane Riviere:
"Net::RawIP relies on SIOCGIFADDR et SIOCGIFHWADDR to get the IP and MAC
addresses of the network interface."
But in a new network namespace these ioctl fail because it is disabled for
a namespace different from the init_net_ns.
These two lines should not be there as af_inet and af_packet are
namespace aware since a long time now. I suppose we forget to remove these
lines because we sent the af_packet first, before af_inet was supported.
Signed-off-by: Daniel Lezcano <daniel.lezcano@free.fr>
Reported-by: Stephane Riviere <stephane.riviere@regis-dgac.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Paris got following trace with a linux-next kernel
[ 14.203970] BUG: using smp_processor_id() in preemptible [00000000]
code: avahi-daemon/2093
[ 14.204025] caller is netif_rx+0xfa/0x110
[ 14.204035] Call Trace:
[ 14.204064] [<ffffffff81278fe5>] debug_smp_processor_id+0x105/0x110
[ 14.204070] [<ffffffff8142163a>] netif_rx+0xfa/0x110
[ 14.204090] [<ffffffff8145b631>] ip_dev_loopback_xmit+0x71/0xa0
[ 14.204095] [<ffffffff8145b892>] ip_mc_output+0x192/0x2c0
[ 14.204099] [<ffffffff8145d610>] ip_local_out+0x20/0x30
[ 14.204105] [<ffffffff8145d8ad>] ip_push_pending_frames+0x28d/0x3d0
[ 14.204119] [<ffffffff8147f1cc>] udp_push_pending_frames+0x14c/0x400
[ 14.204125] [<ffffffff814803fc>] udp_sendmsg+0x39c/0x790
[ 14.204137] [<ffffffff814891d5>] inet_sendmsg+0x45/0x80
[ 14.204149] [<ffffffff8140af91>] sock_sendmsg+0xf1/0x110
[ 14.204189] [<ffffffff8140dc6c>] sys_sendmsg+0x20c/0x380
[ 14.204233] [<ffffffff8100ad82>] system_call_fastpath+0x16/0x1b
While current linux-2.6 kernel doesnt emit this warning, bug is latent
and might cause unexpected failures.
ip_dev_loopback_xmit() runs in process context, preemption enabled, so
must call netif_rx_ni() instead of netif_rx(), to make sure that we
process pending software interrupt.
Same change for ip6_dev_loopback_xmit()
Reported-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dev_pick_tx() caches tx queue_index on a socket, we must check
socket dst_entry matches skb one, or risk a crash later, as reported by
Denys Fedorysychenko, if old packets are in flight during a route
change, involving devices with different number of queues.
Bug introduced by commit a4ee3ce3
(net: Use sk_tx_queue_mapping for connected sockets)
Reported-by: Denys Fedorysychenko <nuclearcat@nuclearcat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Followup of commit 634a4b20
Allow tnode_get_child_rcu() to be called either under rcu_read_lock()
protection or with RTNL held.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At this point optlen == sizeof(sfilter) but some compilers are dumb.
Reported-by: Németh Márton <nm127@freemail.h
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 2626419ad5.
It causes regressions for people with IGB cards. Connection
requests don't complete etc. The true cause of the issue is
still not known, but we should sort this out in net-next-2.6
not net-2.6
Signed-off-by: David S. Miller <davem@davemloft.net>
Back in commit 04a0551c87
("loopback: Drop obsolete ip_summed setting") we stopped
setting CHECKSUM_UNNECESSARY in the loopback xmit.
This is because such a setting was a lie since it implies that the
checksum field of the packet is properly filled in.
Instead what happens normally is that CHECKSUM_PARTIAL is set and
skb->csum is calculated as needed.
But this was only happening for TCP data packets (via the
skb->ip_summed assignment done in tcp_sendmsg()). It doesn't
happen for non-data packets like ACKs etc.
Fix this by setting skb->ip_summed in the common non-data packet
constructor. It already is setting skb->csum to zero.
But this reminds us that we still have things like ip_output.c's
ip_dev_loopback_xmit() which sets skb->ip_summed to the value
CHECKSUM_UNNECESSARY, which Herbert's patch teaches us is not
valid. So we'll have to address that at some point too.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commits 5051ebd275 and
5051ebd275 ("ipv[46]: udp: optimize unicast RX
path") broke some programs.
After upgrading a L2TP server to 2.6.33 it started to fail, tunnels going up an
down, after the 10th tunnel came up. My modified rp-l2tp uses a global
unconnected socket bound to (INADDR_ANY, 1701) and one connected socket per
tunnel after parameter negotiation.
After ten sockets were open and due to mixed parameters to
udp[46]_lib_lookup2() kernel started to drop packets.
Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current X.25 code has some bugs in throughput negotiation:
1. It does negotiation in all cases, usually there is no need
2. It incorrectly attempts to negotiate the throughput class in one
direction only. There are separate throughput classes for input
and output and if either is negotiated both mist be negotiates.
This is bug https://bugzilla.kernel.org/show_bug.cgi?id=15681
This bug was first reported by Daniel Ferenci to the linux-x25 mailing
list on 6/8/2004, but is still present.
The current (2.6.34) x.25 code doesn't seem to know that the X.25
throughput facility includes two values, one for the required
throughput outbound, one for inbound.
This causes it to attempt to negotiate throughput 0x0A, which is
throughput 9600 inbound and the illegal value "0" for inbound
throughput.
Because of this some X.25 devices (e.g. Cisco 1600) refuse to connect
to Linux X.25.
The following patch fixes this behaviour. Unless the user specifies a
required throughput it does not attempt to negotiate. If the user
does not specify a throughput it accepts the suggestion of the remote
X.25 system. If the user requests a throughput then it validates both
the input and output throughputs and correctly negotiates them with
the remote end.
Signed-off-by: John Hughes <john@calva.com>
Tested-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is a patch to stop X.25 examining fields beyond the end of the packet.
For example, when a simple CALL ACCEPTED was received:
10 10 0f
x25_parse_facilities was attempting to decode the FACILITIES field, but this
packet contains no facilities field.
Signed-off-by: John Hughes <john@calva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IGMP3 report parsing is looking at the wrong address for
group records. This patch fixes it.
Reported-by: Banyeer <banyeer@yahoo.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new RCU lockdep support warns about these
in some contexts -- make it aware of the locks
used to protect all this. Different locks are
used in different contexts which unfortunately
means we can't get perfect checking.
Also remove rcu_dereference() from two places
that don't actually dereference the pointers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes the problem introduced in commit
8404080568 which broke mesh peer link establishment.
changes:
v2 Added missing break (Johannes)
v3 Broke original patch into two (Johannes)
Signed-off-by: Javier Cardona <javier@cozybit.com>
Cc: stable@kernel.org
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (37 commits)
smc91c92_cs: fix the problem of "Unable to find hardware address"
r8169: clean up my printk uglyness
net: Hook up cxgb4 to Kconfig and Makefile
cxgb4: Add main driver file and driver Makefile
cxgb4: Add remaining driver headers and L2T management
cxgb4: Add packet queues and packet DMA code
cxgb4: Add HW and FW support code
cxgb4: Add register, message, and FW definitions
netlabel: Fix several rcu_dereference() calls used without RCU read locks
bonding: fix potential deadlock in bond_uninit()
net: check the length of the socket address passed to connect(2)
stmmac: add documentation for the driver.
stmmac: fix kconfig for crc32 build error
be2net: fix bug in vlan rx path for big endian architecture
be2net: fix flashing on big endian architectures
be2net: fix a bug in flashing the redboot section
bonding: bond_xmit_roundrobin() fix
drivers/net: Add missing unlock
net: gianfar - align BD ring size console messages
net: gianfar - initialize per-queue statistics
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
9p: saving negative to unsigned char
9p: return on mutex_lock_interruptible()
9p: Creating files with names too long should fail with ENAMETOOLONG.
9p: Make sure we are able to clunk the cached fid on umount
9p: drop nlink remove
fs/9p: Clunk the fid resulting from partial walk of the name
9p: documentation update
9p: Fix setting of protocol flags in v9fs_session_info structure.
Saving -EINVAL as unsigned char truncates the high bits and changes it
into 234 instead of -22. This breaks the test for "if (ret == -EINVAL)"
in parse_opts().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
dcache prune happen on umount. So we cannot mark the client
satus disconnect. That will prevent a 9p call to the server
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
The recent changes to add RCU lock verification to rcu_dereference() calls
caught out a problem with netlbl_unlhsh_hash(), see below.
===================================================
[ INFO: suspicious rcu_dereference_check() usage. ]
---------------------------------------------------
net/netlabel/netlabel_unlabeled.c:246 invoked rcu_dereference_check()
without protection!
This patch fixes this problem as well as others like it in the NetLabel
code. Also included in this patch is the identification of future work
to eliminate the RCU read lock in netlbl_domhsh_add(), but in the interest
of getting this patch out quickly that work will happen in another patch
to be finished later.
Thanks to Eric Dumazet and Paul McKenney for their help in understanding
the recent RCU changes.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Reported-by: David Howells <dhowells@redhat.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
check the length of the socket address passed to connect(2).
Check the length of the socket address passed to connect(2). If the
length is invalid, -EINVAL will be returned.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
----
net/bluetooth/l2cap.c | 3 ++-
net/bluetooth/rfcomm/sock.c | 3 ++-
net/bluetooth/sco.c | 3 ++-
net/can/bcm.c | 3 +++
net/ieee802154/af_ieee802154.c | 3 +++
net/ipv4/af_inet.c | 5 +++++
net/netlink/af_netlink.c | 3 +++
7 files changed, 20 insertions(+), 3 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_read_sock() can have a eat skbs without immediately advancing copied_seq.
This can cause a panic in tcp_collapse() if it is called as a result
of the recv_actor dropping the socket lock.
A userspace program that splices data from a socket to either another
socket or to a file can trigger this bug.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"mac80211: fix skb buffering issue" still left a race
between enabling the hardware queues and the virtual
interface queues. In hindsight it's totally obvious
that enabling the netdev queues for a hardware queue
when the hardware queue is enabled is wrong, because
it could well possible that we can fill the hw queue
with packets we already have pending. Thus, we must
only enable the netdev queues once all the pending
packets have been processed and sent off to the device.
In testing, I haven't been able to trigger this race
condition, but it's clearly there, possibly only when
aggregation is being enabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1st) a PREQ should only be processed, if it has the same SN and better
metric (instead of better or equal).
2nd) next_hop[ETH_ALEN] now actually used to buffer
mpath->next_hop->sta.addr for use out of lock.
Signed-off-by: Marco Porsch <marco.porsch@siemens.com>
Acked-by: Javier Cardona <javier@cozybit.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanse discovered that kmalloc is being called with GFP_KERNEL while
holding this spinlock. The spinlock can be a mutex instead, which also
enables the removal of the unlock/lock around the lock/unlock of
cfg80211_mutex and the call to set_regdom.
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (33 commits)
r8169: offical fix for CVE-2009-4537 (overlength frame DMAs)
ipv6: Don't drop cache route entry unless timer actually expired.
tulip: Add missing parens.
r8169: fix broken register writes
pcnet_cs: add new id
bonding: fix broken multicast with round-robin mode
drivers/net: Fix continuation lines
e1000: do not modify tx_queue_len on link speed change
net: ipmr/ip6mr: prevent out-of-bounds vif_table access
ixgbe: Do not run all Diagnostic offline tests when VFs are active
igb: use correct bits to identify if managability is enabled
benet: Fix compile warnnings in drivers/net/benet/be_ethtool.c
net: Add MSG_WAITFORONE flag to recvmmsg
e1000e: do not modify tx_queue_len on link speed change
igbvf: do not modify tx_queue_len on link speed change
ipv4: Restart rt_intern_hash after emergency rebuild (v2)
ipv4: Cleanup struct net dereference in rt_intern_hash
net: fix netlink address dumping in IPv4/IPv6
tulip: Fix null dereference in uli526x_rx_packet()
gianfar: fix undo of reserve()
...
This is ipv6 variant of the commit 5e016cbf6.. ("ipv4: Don't drop
redirected route cache entry unless PTMU actually expired")
by Guenter Roeck <guenter.roeck@ericsson.com>.
Remove cache route entry in ipv6_negative_advice() only if
the timer is expired.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When cache is unresolved, c->mf[6]c_parent is set to 65535 and
minvif, maxvif are not initialized, hence we must avoid to
parse IIF and OIF.
A second problem can happen when the user dumps a cache entry
where a VIF, that was referenced at creation time, has been
removed.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new flag MSG_WAITFORONE for the recvmmsg() syscall.
When this flag is specified for a blocking socket, recvmmsg()
will only block until at least 1 packet is available. The
default behavior is to block until all vlen packets are
available. This flag has no effect on non-blocking sockets
or when used in combination with MSG_DONTWAIT.
Signed-off-by: Brandon L Black <blblack@gmail.com>
Acked-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The the rebuild changes the genid which in turn is used at
the hash calculation. Thus if we don't restart and go on with
inserting the rt will happen in wrong chain.
(Fixed Neil's comment about the index passed into the rt_intern_hash)
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need in getting it 3 times and gcc isn't smart enough
to understand this himself.
This is just a cleanup before the fix (next patch).
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a dump is interrupted at the last device in a hash chain and
then continued, "idx" won't get incremented past s_idx, so s_ip_idx
is not reset when moving on to the next device. This means of all
following devices only the last n - s_ip_idx addresses are dumped.
Tested-by: Pawel Staszewski <pstaszewski@itcare.pl>
Signed-off-by: Patrick McHardy <kaber@trash.net>
A missing break statement in hashlimit_ipv6_mask(), and masks
between /64 and /95 are not working at all...
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The order of the IPv6 raw table is currently reversed, that makes impossible
to use the NOTRACK target in IPv6: for example if someone enters
ip6tables -t raw -A PREROUTING -p tcp --dport 80 -j NOTRACK
and if we receive fragmented packets then the first fragment will be
untracked and thus skip nf_ct_frag6_gather (and conntrack), while all
subsequent fragments enter nf_ct_frag6_gather and reassembly will never
successfully be finished.
Singed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
If dl_seq_start() memory allocation fails, we crash later in
dl_seq_stop(), trying to kfree(ERR_PTR(-ENOMEM))
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: don't try to decode GETATTR if DELEGRETURN returned error
sunrpc: handle allocation errors from __rpc_lookup_create()
SUNRPC: Fix the return value of rpc_run_bc_task()
SUNRPC: Fix a use after free bug with the NFSv4.1 backchannel
SUNRPC: Fix a potential memory leak in auth_gss
NFS: Prevent another deadlock in nfs_release_page()
The original code saved the error value but just returned 0 in the end.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jamal Hadi Salim <hadi@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates real_num_tx_queues in case underlying real device
has changed real_num_tx_queues.
-v2
As per Eric Dumazet<eric.dumazet@gmail.com> comment:-
-- adds BUG_ON to catch case of real_num_tx_queues exceeding num_tx_queues.
-- created this self contained patch to just update real_num_tx_queues.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is required to correctly select vlan tx queue for a driver
supporting multi tx queue with ndo_select_queue implemented since
currently selected vlan tx queue is unaligned to selected queue by
real net_devce ndo_select_queue.
Unaligned vlan tx queue selection causes thrash with higher vlan
tx lock contention for least fcoe traffic and wrong socket tx
queue_mapping for ixgbe having ndo_select_queue implemented.
-v2
As per Eric Dumazet<eric.dumazet@gmail.com> comments, mirrored
vlan net_device_ops to have them with and without vlan_dev_select_queue
and then select according to real dev ndo_select_queue present or not
for a vlan net_device. This is to completely skip vlan_dev_select_queue
calling for real net_device not supporting ndo_select_queue.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allows the net_cls cgroup subsystem to be compiled as a module
This patch modifies net/sched/cls_cgroup.c to allow the net_cls subsystem
to be optionally compiled as a module instead of builtin. The
cgroup_subsys struct is moved around a bit to allow the subsys_id to be
either declared as a compile-time constant by the cgroup_subsys.h include
in cgroup.h, or, if it's a module, initialized within the struct by
cgroup_load_subsys.
Signed-off-by: Ben Blum <bblum@andrew.cmu.edu>
Acked-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Paul Menage <menage@google.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: update according to Frans' comments.
Currently, if we leave spaces before dst port,
netconsole will silently accept it as 0. Warn about this.
Also, when spaces appear in other places, make them
visible in error messages.
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: David Miller <davem@davemloft.net>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8ccb92ad (netfilter: xt_recent: fix false match) fixed supposedly
false matches in rules using a zero hit_count. As it turns out there is
nothing false about these matches and people are actually using entries
with a hit_count of zero to make rules dependant on addresses inserted
manually through /proc.
Since this slipped past the eyes of three reviewers, instead of
reverting the commit in question, this patch explicitly checks
for a hit_count of zero to make the intentions more clear.
Reported-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Tested-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Cc: stable@kernel.org
Signed-off-by: Patrick McHardy <kaber@trash.net>
