Remove atomic operations in the fast tx path. Expensive atomic
operations were used to keep track of the number of available tx
descriptors. The new code uses the difference between the consumer
and producer index to determine the number of free tx descriptors.
As suggested by Jeff Garzik, the name of the inline function is
changed to all lower case.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This speeds up link-up time on 5706 SerDes if the link partner does
not autoneg, a rather common scenario in blade servers. Some blade
servers use IPMI for keyboard input and it's important to minimize
link disruptions.
The speedup is achieved by shortening the timer to (HZ / 3) during
the transient period right after initiating a SerDes autoneg. If
autoneg does not complete, parallel detect can be done sooner. After
the transient period is over, the timer goes back to its normal HZ
interval.
As suggested by Jeff Garzik, the timer initialization is moved to
bnx2_init_board() from bnx2_open().
An eeprom bit is also added to allow default forced SerDes speed for
even faster link-up time.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes an rtnl deadlock problem when flush_scheduled_work() is
called from bnx2_close(). In rare cases, linkwatch_event() may be on
the workqueue from a previous close of a different device and it will
try to get the rtnl lock which is already held by dev_close().
The fix is to set a flag if we are in the reset task which is run
from the workqueue. bnx2_close() will loop until the flag is cleared.
As suggested by Jeff Garzik, the loop is changed to call msleep(1)
instead of yield() in the original patch.
flush_scheduled_work() is also moved to bnx2_remove_one() before the
netdev is freed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains the following possible cleanups/fixes:
- use C99 struct initializers
- make a few arrays and structs static
- remove a few uses of literal 0 as NULL pointer
- use convenience function instead of cast+dereference in bnx2_ioctl()
- remove superfluous casts to u8 * in calls to readl/writel
Signed-off-by: Peter Hagervall <hager@cs.umu.se>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Found a bug while reviewing the patches the second time.
The TG3_FLAG_TXD_MBOX_HWBUG flag is set after the register access
methods have been determined. This patch fixes it by moving it up before
the various access methods are assigned.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register write to register 0x68 to restart interrupts is unnecessary
as the interrupt wasn't masked in that register by the irq handler. This
will save one register write in the fast path.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the new workaround for 5703 A1/A2 if it is behind
certain ICH bridges. The workaround disables memory and uses config.
cycles only to access all registers. The 5702/03 chips can mistakenly
decode the special cycles from the ICH chipsets as memory write cycles,
causing corruption of register and memory space. Only certain ICH
bridges will drive special cycles with non-zero data during the address
phase which can fall within the 5703's address range. This is not an ICH
bug as the PCI spec allows non-zero address during special cycles.
However, only these ICH bridges are known to drive non-zero addresses
during special cycles.
The indirect_lock is also changed to spin_lock_irqsave from spin_lock_bh
because it is used in irq handler when using the indirect method to
disable interrupts.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the mailbox read method and also adds an inline function
tw32_mailbox_f() for mailbox writes that require read flush.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds various dedicated register read/write methods for the
existing workarounds, including PCIX target workaround, write with read
flush, etc. The chips that require these workarounds will use these
dedicated access functions.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the basic function pointers to do register accesses in
the fast path. This was suggested by David Miller. The idea is that
various register access methods for different hardware errata can easily
be implemented with these function pointers and performance will not be
degraded on chips that use normal register access methods.
The various register read write macros (e.g. tw32, tr32, tw32_mailbox)
are redefined to call the function pointers.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead, set it in one place, namely the beginning of
netif_receive_skb().
Based upon suggestions from Jamal Hadi Salim.
Signed-off-by: David S. Miller <davem@davemloft.net>
Bonding just wants the device before the skb_bond()
decapsulation occurs, so simply pass that original
device into packet_type->func() as an argument.
It remains to be seen whether we can use this same
exact thing to get rid of skb->input_dev as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes the private element from skbuff, that is only used by
HIPPI. Instead it uses skb->cb[] to hold the additional data that is
needed in the output path from hard_header to device driver.
PS: The only qdisc that might potentially corrupt this cb[] is if
netem was used over HIPPI. I will take care of that by fixing netem
to use skb->stamp. I don't expect many users of netem over HIPPI
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the "list" member of struct sk_buff, as it is entirely
redundant. All SKB list removal callers know which list the
SKB is on, so storing this in sk_buff does nothing other than
taking up some space.
Two tricky bits were SCTP, which I took care of, and two ATM
drivers which Francois Romieu <romieu@fr.zoreil.com> fixed
up.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
This patch adds back the code that was taken out, thus re-enabling:
* The PHY Layer to initialize without crashing
* Drivers to actually connect to PHYs
* The entire PHY Control Layer
This patch is used by the gianfar driver, and other drivers which are in
development.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
With my Buffalo WLI-CF-S11G PC Card kernel oopses every time in
prism2_interrupt() when I try load the hostap module. local->hw_priv is null
during the first call to prism2_interrupt(). It feels like
interrupts are enabled too early, or something.
This patch fixes the symptom, but not the cause.
Signed-off-by: Kalle Valo <Kalle.Valo@iki.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
hostap_cs: 0.4.1-kernel (Jouni Malinen <jkmaline@cc.hut.fi>)
pcmcia: hostap_cs: invalid hash for product string "BUFFALO": is 0x1b01a57b,
should be 0x2decece3
pcmcia: see Documentation/pcmcia/devicetable.txt for details
pcmcia: hostap_cs: invalid hash for product string "WLI-CF-S11G": is
0xefd5102a, should be 0x82067c18
pcmcia: see Documentation/pcmcia/devicetable.txt for details
This patch fixes them.
Signed-off-by: Kalle Valo <Kalle.Valo@iki.fi>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Version 0.4.4 of Host AP driver was released, so let's sync the version
number in netdev-2.6 tree.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Both revisions share the same PCI device ID and vendor ID but revision 2
of the device uses SysKonnect's chipset whereas revision 3 of the device
uses Realtek's 8169 chipset.
Credit goes to Christiaan Lutzer <mythtv.lutzer@gmail.com> for reporting
the issue and giving the actual value for the different revisions.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Rewrite the mkiss driver to make it SMP-proof following the example of
6pack.c.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Don't check type of sax25_family; dev_set_mac_address has already done
that before and anyway, the type to check against would have been
ARPHRD_AX25. We only got away because AF_AX25 and ARPHRD_AX25 both happen
to be defined to the same value.
Don't check sax25_ndigis either; it's value is insignificant for the
purpose of setting the MAC address and the check has shown to break
some application software for no good reason.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
I dropped the timer initialization bits by accident when sending the
p-persistence fix. This patch gets the driver to work again on halfduplex
links.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The userspace must not be able to issue ethtool command and manage the
mii before it is completely initialized. Avoid some pesky "eth%d" messages.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
From: Gertjan van Wingerde <gwingerde@home.nl>
Attached patch updates the definitions of the generic ieee80211 stack to
the latest versions of the published 802.11x specification suite.
Signed-off-by: Gertjan van Wingerde <gwingerde@home.nl>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
This removes one trap for a programmer, few unused macros, and one
unused struct.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
From: Imre Deak <imre.deak@nokia.com>
I had a problem where doing an open after a close left the device
unusable. netif_carrier_on should be called whenever we go to the
associated state, but this is not so in case of a close->open sequence.
Signed-off-by: Jiri Benc <jbenc@suse.cz>
From: Adrian Bunk <bunk@stusta.de>
This patch contains the following possible cleanups:
- make needlessly global code static
- remove the unused IPW_DEBUG_ENABLED
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
From: Pavel Machek <pavel@ucw.cz>
ipw2100 uses custom debug prints that are sometimes longer and always
harder to read than normal printk. They also introduced some bugs where
prefix is printed twice.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
From: Pavel Machek <pavel@ucw.cz>
ipw2100 uses strange X__ prefixes even for symbols already prefixed
by ipw2100. Fixed.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
The tg3_abort_hw() call in tg3_test_loopback() is causing lockups on
some devices. tg3_abort_hw() disables the memory arbiter, causing
tg3_reset_hw() to hang when it tries to write the pre-reset signature.
tg3_abort_hw() should only be called after the pre-reset signature has
been written. This is all done in tg3_reset_hw() so the tg3_abort_hw()
call is unnecessary and can be removed.
[ Also bump driver version and release date. -DaveM ]
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver version, white space, comments & other
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add cpu cycle saver microcode to 8086:{1209/1229} other than ICH devices.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed endian bug associated with cb_i bit in xmit_prepare
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
added msleep_interruptible delay right before returning from diag_test
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Do not check Rx packet length against mtu - patch from Darren Tucker
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
airo_cs is broken on m32r; marked as such. [Proper fix would involve
separating PCI-dependent parts and making sure they don't get in the
way _and_ arranging for asm/scatterlist.h getting picked on m32r]
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ISA parts of tms380tr are using ISA DMA helpers and should depend on
ISA_DMA_API.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The purpose of this patch:
- Adopt the DMA API (jazzsonic, macsonic & core driver).
- Adopt the driver model (macsonic).
This part was cribbed from jazzsonic. As a consequence, macsonic once
again works as a module. Driver model is also used by the DMA calls.
- Support 16 bit cards (macsonic & core driver, also affects jazzsonic)
This code was adapted from the mac68k linux 2.2 kernel, where it has
languished for a long time.
- Support more 32-bit mac cards (macsonic)
Also from mac68k repo.
- Zero-copy buffer handling (core driver)
Provides a nice performance improvement. The new algorithm incidentally
helped to replace the old Jazz DMA code.
The patch was tested on a variety of macs (several 32-bit quadra built-in
NICs, a 16-bit LC PDS NIC and a 16-bit comm-slot NIC), and also on MIPS
Jazz.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[PATCH] [NET] mv643xx: add workaround for HW checksum generation bug
The hardware checksum generator on the mv64xxx occasionally generates
an incorrect checksum. This patch works around the issue and enables
hardware checksum generation.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
Patch Description:
This patch incorporates the following hardware fixes required
for Xframe II adapter.
1. New values to program the dtx_control register.
2. Disable memory controller interrupts(MC_INTR) since these
are now monitored thru' a poll routine.
3. Don't reset an XframeII card on an ECC double-bit error(It
can recover).
4. Save/restore PCI config space before/after a reset irrespective
of Xframe I or II card.
5. Bumped up the driver version no. to 2.0.3.1
Please review the patch and apply the same if it looks ok.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Now that all tms380 devices have a valid
struct device with dma_mask, remove dmalimit from tmsdev_init().
Kconfig: depend tms380tr and madgemc on MCA.
abyss.c, proteon.c, skisa.c, tmspci.c, tms380tr.h:
remove dmalimit parameter from tmsdev_init().
tms380tr.c: use device->dma_mask instead of dmalimit.
madgemc.c: move to new MCA API using struct device.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
A problem was reported by Grant Grundler on an HP rx8620 using IOX
Core LAN partno(A7109-6) 5701 copper NIC. The tg3 driver mistakenly
detects this NIC as having a SerDes PHY and link does not come up as a
result.
The problem was caused by an incorrectly programmed eeprom that set the
NIC_SRAM_DATA_CFG_PHY_TYPE_FIBER bit in the NIC_SRAM_DATA_CFG location.
This patch will override the NIC_SRAM_DATA_CFG_PHY_TYPE_FIBER bit if a
valid PHY ID is read from the MII registers on older 570x chips where
the MII interface is not used on SerDes chips. On newer chips such as
the 5780 that use MII for both copper and SerDes, SerDes detection must
rely on the eeprom.
This patch will make the SerDes detection identical to versions 3.25 and
older.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Grant Grundler <iod00d@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/e1000/e1000_main.c: In function `e1000_clean_tx_irq':
drivers/net/e1000/e1000_main.c:2774: warning: size_t format, dma_addr_t arg (arg 8)
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The multicast code of the fmvj18x_cs driver is broken.
I fixed it to work properly.
Signed-off-by: komurojun-mbn@nifty.com
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
SIS190 must select MII since it's using it.
While I was editing the Kconfig entry, I also converted the spaces to
tabs.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The Linksys EG1032 uses Realtek's 8169 chipset.
Credit goes to Bob Wilson <bwilson4web@hotmail.com> for the report.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use msleep_interruptible() instead of delay_cycx() to guarantee the task
delays as expected. Remove the prototype and definition of delay_cycx().
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Rdiger found a bug in nv_open that explains some of the reports
with duplex mismatches:
nv_open calls nv_update_link_speed for initializing the hardware link speed
registers. If current link setting matches the values in np->linkspeed and
np->duplex, then the function does nothing.
Usually, doing nothing is the right thing, but not in nv_open: During
nv_open, the registers must be initialized because the nic was reset.
The attached patch fixes that by setting np->linkspeed to an invalid value
before calling nv_update_link_speed from nv_open.
Signed-Off-By: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The DM9000 driver is responding to ioctl() calls it should not be. This
can cause problems with the wireless tools incorrectly indentifying the
device as wireless capable, and crashing under certain operations.
This patch also moves the version printk() to the init call, so that
you only get it once for multiple devices, and to show it is loaded
if there are no defined dm9000s
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix DM9000 driver usage of spinlocks, which mainly came to light
when running a kernel with spinlock debugging. These come down to:
1) Un-initialised spin lock
2) Several cases of using spin_xxx(lock) and not spin_xxx(&lock)
3) move the locking around the phy reg for read/write to only
keep the lock when actually reading or writing to the phy.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
After suspend the driver needs to retest link status in case the cable
has been inserted or removed during the suspend.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- Using the right register clearly improves chances of getting the MII
code and thus the driver working at all.
- On startup check the media type before setting up duplex or we might
spend the first 1.2s with a wrong duplex setting.
- Get rid of whitespace lines.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The flush threshold in the MAC chip should be increased.
Found while reviewing vendor version of sk98lin driver.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Some versions of the Marvell yukon generate bogus sensor warning interrupts.
The driver would flood log with these messages. Handle this situation
cleanly by masking away at boot time.
Fixes: http://bugs.gentoo.org/show_bug.cgi?id=87182
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
drivers/net/skge.c | 24 ++++++++++--------------
drivers/net/skge.h | 8 ++++++--
2 files changed, 16 insertions(+), 16 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Replace remaining WLAN_FC_* defines with the ones used in ieee80211
header file. This completes the move from hostap version of frame
control field processing to ieee80211 version.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Remove backwards compatibility define for WLAN_CAPABILITY_ESS now that
net/ieee80211.h defines this.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
IEEE 802.11 has a capability field flag called ESS, but ieee80211 had
renamed this to BSS for some reason. hostap has been using
WLAN_CAPABILITY_ESS and since that matches with the standard, lets use
it as the name for this define. Add WLAN_CAPABILITY_BSS as a backwards
compatibility name for the same bit since ieee80211 and ipw2200 are
using this and there are versions outside kernel tree that expect to
find this define name.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Replace temporary HOSTAP_FC_GET_{TYPE,STYPE} macros with the ieee80211
version of WLAN_FC_GET_{TYPE,STYPE}.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Remove unused defines that are already available from generic kernel
header files.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Replace hardware model specific #ifdef's in struct local_info with
void *hw_priv that is pointing to cs/pci/plx specific data
structure. This removes unneeded #ifdef's and as such, is a step
towards making it possible to share objects for hostap_hw.c and
hostap_download.c with cs/pci/plx drivers without having to compile
and link the same code separately for each one.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
PCI version of Prism2.5/3 has undocumented DMA support for TX/RX data,
but this seems to have some hardware bugs that prevent it from being
used properly for TX. RX side could possibly be made to work reliably.
Even though DMA support would be very useful for saving host CPU (from
about 40% to 5-10% when operating at maximum throughput), it seems to
be best to just remove this code finally. The implementation has
always been commented out by default and has received very limited
testing. The code may have already been broken number of times and I
don't have much interested in trying to verify whether it works or
not. Getting this out makes it easier to maintain the driver and
allows some cleanups that have been partly postponed because of this
experimental bus master/DMA code.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Old AP mode code for power saving was using skb->cb for couple of
flags before the more generic 802.11 TX code started using the same
buffer for struct hostap_skb_tx_data. This resulted in the power save
code corrupting the magic value in beginning of the buffer and TX code
dropping the power saved packets because of this for the case where
STAs send PS-Poll frames with PwrMgmt flag set.
This patch modifies the power save code to use the same struct
hostap_skb_tx_data as rest of the TX path in order to avoid corrupting
the data in skb->cb.
In addition, this patch reorders fields in the structure and makes
them use smaller types in order to make the structure fit in skb->cb
on 64-bit hosts.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Suggested by Steven Rostedt, matches his patch included in e100.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Redefined buffer_info-dma to be dma_addr_t instead of uint64
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Remove unused functions, render some variable static instead of global - based on patch from Adrian Bunk
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Ethtool cleanup patch from Stephen Hemminger
* use ADVERTISED_xxx fields when setting advertised fields
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix data output by ethtool -d
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use netdev_priv() instead of netdev->priv
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix unnecessary link state messages
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Set RXDCTL:PTHRESH/HTHRESH to zero
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add the device ID of the Buffalo AirStation WLI-CF-S11G
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This is a patch to incorporate comments from earlier 12 patches.
It also fixes a few issues we found during this time.
Following is a list of changes in this patch. Item 1 incorporates
earlier comments. Issues addressed in items 2 to 4 were discovered
recently.
1. wmb() call in s2io_xmit() replaced with mmiowb().
2. The dtx_control register was earlier programmed incorrectly
for Xframe II adapter.
3. As suggested by hardware team, after a reset, in case of
Xframe II adapter, we clear certain spurious errors by
clearing PCI-X ECC status register, "detected parity error"
bit in PCI_STATUS register and PCI_STATUS bit in txpic_int register.
4. On IBM PPC platforms, we found that in the Rx buffer replenish
function, two memory writes(one to the the descriptor length and
another to the ownership) were getting reordered. This was causing
the adapter to see the ownership transfered to it before the length
was updated.
One solution was to add a wmb() but since this would turnout expensive
on some platforms if called for every descriptor, we set the ownership
bit and other fields of '2' to 'N' Rx descriptors followed by a wmb()
and then set the ownership of first descriptor ('1').
Here the value 'N' is configurable by making it a module loadable
parameter (rxsync_frequency).
(NOTE: This parameter is a power of 2).
5. Bumped up the driver version no. to 2.0.2.1
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
The last patch in this series fixes the following issues found during
testing.
1. Ensure we don't pass zero sized buffers to the card(which can lockup)
2. Restore the PCI-X parameters(in case of Xframe I adapter) after a reset.
3. Make sure total size of all FIFOs does not exceed 8192.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
The below patch implements a new "Link state change handling"
scheme supported by the Xframe II adapter. It also bumps up the
driver version to 2.0.2.0.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This is a patch to provide bimodal interrupt moderation support for
Xframe II adapter. Basically, in this moderation scheme, the adapter
raises a traffic interrupt if the no. of packets transmitted and/or
received reaches a programmable threshold.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This patch provides basic support for the Xframe II adapter.
Includes the following changes:
1. New values to program XAUI interface.
2. Print the PCI/PCI-X mode(bus frequency, width).
3. Remove EOI from reset during intialization.
4. Enable all 8 PCCs if Xframe II adapter.
5. Programs the RLDRAM size depending on the device.
(Note: RLDRAM size on XFARME-I is 64Mb whereas on XFRAME-II it's 32 Mb).
6. Enable extended(64-bit) statistics counters.
7. Program timer interrupt duration based on PCI/PCI-X clock speed.
8. Not required to save/restore PCI config space before/after reset.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This patch implements the slow-path handling functions(link
state change, hardware errors) as a timer. It is not
handled in interrupt handler as was done previously.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This patch relates to mostly performance related changes.
1. Fixed incorrect computation of PANIC level in rx_buffer_level().
2. Removed unnecessary PIOs(read/write of tx_traffic_int and
rx_traffic_int) from interrupt handler and removed read of
general_int_status register from xmit routine.
3. Enable two-buffer mode(for Rx path) automatically for SGI
systems. This improves Rx performance dramatically on
SGI systems.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This patch fixes certain memory leaks discovered in free_tx_buffers()
and rx_osm_handler()
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
Below patch includes fixes for few purely software bugs identified
since last release.
1. Keep track and display(as part of ethtool command output) the no.
of single-bit and double-bit ECC errors.
2. Handle race condition between intr handler and "interface down"
routine.
3. Initial link state setting modified so that the link state displayed
after "interface Up" is correct.
4. Fix for "Incorrect Tx packet count when TSO is enabled".
5. Disable periodic DMA of statistics and schedule one-shot DMA
only when required.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
Below patch addresses few h/w specific issues.
1. Check for additional ownership bit on Rx path before
starting Rx processing.
2. Enable only 4 PCCs(Per Context Controller) for Xframe I
revisions less than 4.
3. Program Rx and Tx round robin registers depending on
no. of rings/FIFOs.
4. Tx continous interrupts is now a loadable parameter.
5. Reset the card if we get double-bit ECC errors.
6. A soft reset of XGXS being done to force a link state change has been
eliminated.
7. After a reset, clear "parity error detected" bit,
PCI-X ECC status register, and PCI_STATUS bit in
tx_pic_int register.
8. The error in the disabling allmulticast implementation has been
rectified.
9. Leave the PCI-X parameters MMRBC, OST etc. at their
BIOS/system defaults.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
We are submitting a series of 13 patches to support our Xframe I and
Xframe II line of products. The patches can be categorized as follows:
Patches 1-8 : Changes applicable to both Xframe I and II
Patches 9-11: Xframe II specific features
Patch 12: Addresses issues found during testing cycle.
Patch 13: Incorpoates mostly the review comments from community
and some last moment bug fixes.
Please review the patches and let us know your comments.
Starting with patch 1 below.
This patch involves cosmetic changes(tabs and indentation,
regrouping of transmit and receive data structures, typecasting,
code cleanup).
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix the p-persistence CSMA algorithm which in simplex mode was starting
with a slottime delay before doing anything else as if there was carrier
collision resulting in bad performance on simplex links.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Else on SMP systems it is possible for hotplug to execute,
invoke tg3_open(), and end up loading the uninitialized
PCI register save area into the card.
Signed-off-by: David S. Miller <davem@davemloft.net>
cs89x0 talks a lot at boot. Seems like debug leftover. This patch
downgrades printks to KERN_DEBUG. While we're at it, make these messages a
bit less obscure.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make it compile with CONFIG_PM=n
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Drivers really only work well in SMP if they actually can be selected.
This is a leftover from the time when the 6pack drive only used to be
a bitrotten variant of the slip driver.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Kconfig | 2 +-
1 files changed, 1 insertion(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Whitespace cleanup for loopback driver. Hopefully it fixes the last few
annoyances.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch slightly optimizes the loopback driver's stats update.
Saves two loads, one add and one increment per packet sent.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch #ifdefs the TSO code in the loopback driver.
Saves ~800 bytes of text on i386 and avoids a conditional in the fast path.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
--ReaqsoxgOBHFXBhH
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline
Hi Jeff,
Here's a little patch fixing a typo in smc91x.h.
Regards,
Tony
--ReaqsoxgOBHFXBhH
Content-Type: text/x-chdr; charset=us-ascii
Content-Disposition: inline; filename="patch-fix-typo-smc91x.h"
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use module_param() instead of the old MODULE_PARM()
Signed-off-by: Victor Fusco <victor@cetuc.puc-rio.br>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Yukon-Lite chipset needs workaround for revision 7 (or later).
Without this patch, chip gets stuck in low power mode and never
boots. Newer SysKonnect vendor code already had same patch.
Related bug in skge is http://bugs.gentoo.org/87822
Chris, please add for 2.6.12.2
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Cleanup code that is used to toggle LED's. Since we
get called from ethtool, can use that thread rather than
setting up a timer.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
During autonegotiation set PHY interrupt mask to ignore
bogus speed change interrupts.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The code to clear fifo errors was incorrect and sending garbage
to the external phy. Removed the no longer used inline's funcs.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The check for Yukon lite changes was restricting itself to
rev A3. It turns out that these changes are also true on A4
and later.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Cleanup the phy_lock deadlock because of relocking in the nway_reset path.
Reported by Francois Romieu.
Also, don't need to do irqsave/restore for blink,
just excluding bh is good enough.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Here is a fix for a typo, thanks Eliot Dresselhaus.
Since transmitter not active when device is down, it wasn't really noticed.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The SK-9E boards use the Marvell Yukon2 chipset which
is not supported by the skge driver. Thanks to Ralph Roesler
for noticing.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Using Genesis board, I get harmless error reports. Rather than console
error, turn it into a error counter.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
A few sparse cleanups for orinoco.c
Signed-off-by: Peter Hagervall <hager@cs.umu.se>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch makes tms380tr use the new DMA API. Now that on Alpha, this API
also supports bus master DMA for ISA (platform) devices, i changed the
driver to use this new API.
This also works around a bug in the firmware loader: The example provided
in Documentation/firmware_class no longer works, as the firmware loader now
calls get_kobj_path_length() and the kernel promptly oopses, as the
home-grown device doesn't have a parent. Of course, this doesn't happen
with a "real" device which has its bus (or pseudo bus in the case of
platform) as parent.
Converted tms380tr to use new DMA API:
- proteon.c, skisa.c: use platform pseudo bus to create a struct device
- Space.c: delete init hooks
- abyss.c, tmspci.c: pass struct device to tms380tr.c
- tms380tr.c, tms380tr.h: new DMA API, use real device fo firmware loader
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
In ALB mode, allow new slave to use bond's MAC address if the new
slave's MAC address is being used within the bond and no other slave
is using the bond's MAC address.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Replace Host AP version of WEP, TKIP, CCMP implementation with
net/ieee80211 that has more or less identical implementation (since
it is based on the Host AP implementation). Remove Host AP specific
implementation and modules from drivers/net/wireless/hostap.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Preparations for starting to use net/ieee80211 instead of private
IEEE 802.11 implementation. Include net/ieee80211.h and
net/ieee80211_crypt.h into files that will be needed these in the
future. Remove duplicate definitions from hostap_common.h and
rename WLAN_FC_GET_{TYPE,STYPE} macros for now sinc net/ieee80211.h
is using incompatible definitions. This will be resolved in the
future by updating Host AP to use the versions that do not shift
type/stype.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
ethernet drivers to remain as ignorant as is reasonable of the connected
PHY's design and operation details.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The station control register must depend on both the advertisement and the lpa
The link partner ability has better be intersected with the current
advertised value before it is feed to the station control register.
Sight-catched-by: Lars Vahlenberg <lars.vahlenberg@gmail.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Added PHY identifier for the Asus K8S-MX motherboard
Note: the same ID appears in the sis900 driver.
Signed-off-by: Lars Vahlenberg <lars.vahlenberg@gmail.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add a dummy read before accessing the status register
SiS driver suggests it.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Allow a non-hardcoded ID for the PHY
This is the first step before the driver probes for the PHY address.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
extract bits definition from SiS driver
- fix the Rx stats;
- minor pieces of documentation.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add a restriction to the size of the Rx buffer
SiS driver forces the size of any Rx buffer to be a multiple of 64 bit.
I would not be surprized that it goes along with some alignment issues
which have been experienced before. So far it does not make much of a
difference (both drivers use 1536 bytes buffer).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Extract some mac addr code from SiS's driver.
Some magic may hide beyond the isa bridge. The Rx mac control
register is now set without condition.
Note: good or bad, this part of the code is quite close to sis900.c.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Replace hardcoded constants by enumerated values in sis190_read_eeprom
The names of the enumerated values have been extracted from SiS'official
driver (v1.00.00 published on 2005/07/11).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Merge some register related information from SiS driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
ethtool/mii support
Bug: disabling autonegotiation and setting the link parameters at the
same time does not provide the expected result. More investigation is
needed.
Note: past the initial probe/open time, the link is managed from user-space
or accessed through sis190_phy_task, i.e. in a usermode context. Whence the
very limited locking needs.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
netconsole support.
This stuff should be factored out of every driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Raise the sis190 driver from the dead
The driver handles the integrated network device found on SiS 965L
chipset. It follows the classical (non-napi) interrupt-driven model
and provides minimal ethtool support.
The code comes from a heavy cleanup/rewrite of the original code
which was removed from the kernel on 14/04/2004. Since the r8169
driver does not work too bad and there will probably be (at least)
a few months of improvements/testing/fixing, I made the code as
close as possible to the r8169 one.
Pascal Chapperon <pascal.chapperon@wanadoo.fr> deserves some special
credit for testing and bug-catching. Many thanks to Lars Vahlenberg
as well.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed beacon frame when moving from monitor mode to master mode
(workaround for firmware bug that left IBSS IE in the Beacon
frames). This is using the same workaround that was previously used
when moving from adhoc mode to master mode.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Warning fix for 64-bit platforms
Hello!
The patch fixes following warning seen on 64-bit platforms (in my case -
x86_64, gcc-4.0):
In file included from /usr/local/src/hostap/driver/modules/hostap_cs.c:203:
/usr/local/src/hostap/driver/modules/hostap_hw.c: In function ?prism2_transmit_cb?:
/usr/local/src/hostap/driver/modules/hostap_hw.c:1674: warning: cast from pointer to integer of different size
/usr/local/src/hostap/driver/modules/hostap_hw.c: In function ?prism2_transmit?:
/usr/local/src/hostap/driver/modules/hostap_hw.c:1758: warning: cast to pointer from integer of different size
prism2_transmit_cb uses a (void *) argument to get an integer. A
simple fix would be to use double cast from pointer to long and then to
int (and vice versa when int is passed as a pointer). But I prefer a
slightly longer patch.
I believe that whenever an argument can hold both a pointer and an
integer, it should be declared long. long can hold both pointers and
integers (except win64, but we are not coding for Windows), it can be
cast to both of them and it's never assumed to be a valid pointer, which
could be useful for some automatic code checkers.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
line 129 of hostap_80211_rx.c should read:
LWNG_SETVAL(mactime, 2, 0, 4, rx_stats->mac_time);
not:
LWNG_SETVAL(mactime, 2, 0, 0, rx_stats->mac_time);
The length field is incorrect.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Firmware seems to be getting into odd state in host_roaming mode 2
when hostscan is used without join command, so try to fix this by
re-joining the current AP. This does not actually trigger a new
association if the current AP is still in the scan results.
This makes background scans (iwlist wlan0 scan) not to break data
connection when in host_roaming 2 mode, e.g., when using wpa_supplicant.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Cleaned up scan result processing by converting struct
hfa384x_scan_result into struct hfa384x_hostscan_result. This removes
special cases from result processing since the results are only used
in one, hostscan, format.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Added support for setting channel mask for scan requests
('iwpriv wlan0 scan_channels 0x00ff' masks scans to use channels 1-8).
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add MODULE_VERSION information for the Host AP kernel modules and
update the version string to indicate which version of the external
Host AP driver is included in the kernel tree.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
pcmcia id_table for hostap_cs.c
Hi Jouni,
Here's a patch for adding a pcmcia id_table to hostap_cs.c as introduced
by the PCMCIA subsystem changes in linux-2.6.13-rc1. The id_table allows
hotplug (along with pcmciautils [1]) to load the driver without the need
for the pcmcia-cs cardmgr daemon.
The id_table was generated from the CVS version of hostap_cs.conf using
a script borrowed from Dominik Brodowski. I have removed any duplicate
entries, but I have only been able to test the functionality of the
patch with a Linksys WPC11v3.
Sincerely,
Brix
[1]: http://www.kernel.org/pub/linux/utils/kernel/pcmcia/
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Create sysfs "device" files for hostap
I was writing some scripts to automatically build kismet source lines,
and I noticed that hostap devices don't have device files, unlike my
prism54 and ipw2200 cards:
$ ls -l /sys/class/net/eth0/device
/sys/class/net/eth0/device -> ../../../devices/pci0000:00/0000:00:1e.0/0000:02:01.0
$ ls -l /sys/class/net/wifi0
ls: /sys/class/net/wifi0/device: No such file or directory
$ ls -l /sys/class/net/wlan0
ls: /sys/class/net/wlan0/device: No such file or directory
The following (quite small) patch makes sure that both the wlan and wifi
net devices have that pointer to the bus device.
This way, I can do things like
for i in /sys/class/net/*; do
if ! [ -e $i/device/drive ]; then
continue;
fi;
driver=$(basename $(readlink $i/device/driver))
case $driver in
hostap*)
echo -- hostap,$i,$i-$driver
break;
ipw2?00)
echo -- $driver,$i,$i-$driver
break;
prism54)
echo prism54g,$i
esac
done
Which should generate a working set of source lines for kismet no matter
what order I plug the cards in.
It might also be handy to have a link between the two net devices, but
that's a patch for another day.
That patch is against 2.6.13-rc1-mm1.
-- Dave
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
hostap_cs: Remove irq_list, irq_mask and pcmcia/version.h
Remove irq_list, irq_mask and pcmcia/version.h as suggested in
http://kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
EXPORT_SYMTAB does nothing. There's no need to define something if it
doesn't have any effect.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Update hostap_cs to use new PCMCIA event callback registration.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
An early version of the sk98lin patch was merged via Len's tree. But there
were subsequent updates as a result of review from Jeff. THis fixes things
up.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We want to extract our LAN card driver from tulip core driver and
make a new file uli526x.c at tulip folder, because we have added
some ethtool interface support and non-eprom support in our driver
and may be other change in the futher.
If our controllers support are still contained in the tulip core
driver, I think it'll increase the complexity of maintenance, you
know, tulip core driver include several files and support so many
other controllers. Furthermore, I tested the newest kernel 2.6.12
and I found the tulip driver can not work on our lan controller, and
I no time to debug it, so I aspired want to make a single uli526x.c
file just for our controllers. Could you help us remove the ULi
m5261/m5263 lan controller support from tulip core driver and add
the new single uli526x.c file for us?
Signed-off-by: Peer Chen <Peer.Chen@uli.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
sys_reboot() now calls device_suspend(), so it is no longer necessary for
the e1000 driver to register a reboot notifier [in fact doing so results in
e1000_suspend() getting called twice].
(akpm: we need to fast-track this. It's causing ia64 to oops on shutdown)
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: <cramerj@intel.com>
Cc: <john.ronciak@intel.com>
Cc: <ganesh.venkatesan@intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the product-id-string contains the '+' , '&' ,'_', it was not converted
properly from the /etc/pcmcia/config(pcmcia-cs config file).
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove duplicates from the device id table.
Signed-off-by: Jarkko Raja <jar@pcuf.fi>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
`gcc -W' likes to complain if the static keyword is not at the beginning of
the declaration. This patch fixes all remaining occurrences of "inline
static" up with "static inline" in the entire kernel tree (140 occurrences in
47 files).
While making this change I came across a few lines with trailing whitespace
that I also fixed up, I have also added or removed a blank line or two here
and there, but there are no functional changes in the patch.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
turn many #if $undefined_string into #ifdef $undefined_string to fix some
warnings after -Wno-def was added to global CFLAGS
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move in_aton to allow netpoll and pktgen to work without the rest of
the IPv4 stack. Fix whitespace and add comment for the odd placement.
Delete now-empty net/ipv4/utils.c
Re-enable netpoll/netconsole without CONFIG_INET
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suggestion from Sam Ravnborg <sam@ravnborg.org>
It causes all driver families to be displayed aligned immediately under the
main network drivers heading (in menuconfig/xconfig/gconfig) instead of
not being subordinate to (i.e., not indented) the Network device support
heading at all.
The improved network driver families are:
token ring, wireless, PCMCIA, WAN, ATM, and S390.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 5780S support by adding a new tg3_setup_fiber_mii_phy() function and
a timer function for parallel link detection. 5780S uses standard MII
registers for 1000BaseX and runs in GMII mode as opposed to TBI mode on
older serdes chips.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disallow jumbo TSO on 5780 due to hardware restrictions.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate all DMA watermark settings for standard and jumbo frames on
all chips in tg3_init_bufmgr_config() and add new settings for 5780.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new rx_pkt_buf_sz to the tg3 structure to support variable buffer
sizes on the standard ring.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic jumbo frames support for 5780. This chip supports jumbo frames
on the standard receive ring without the jumbo ring. The
TG3_FLAG_JUMBO_ENABLE is changed to TG3_FLAG_JUMBO_RING_ENABLE to
indicate using the jumbo ring on 5704 and older chips. A new
TG3_FLG2_JUMBO_CAPABLE flag is added to indicate jumbo frames support
with or without the jumbo ring.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 5780 PCI IDs, chip IDs, and other basic support.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETCONSOLE=y and INET=n results in the following compile error:
net/built-in.o: In function `netpoll_parse_options':
: undefined reference to `in_aton'
net/built-in.o: In function `netpoll_parse_options':
: undefined reference to `in_aton'
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put NETCONSOLE and NETPOLL options together since they are related.
This cuts down on the hassle of flipping back and forth between
the Networking menu and the Network drivers menu to change their
config settings.
Tested with menuconfig, gconfig, and xconfig.
gconfig has a small problem with this. I think that it's
a bug in gconfig and I will take it up with Romain Lievin.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Marcelo Feitoza Parisi <marcelo@feitoza.com.br>
Use of the time_after() macro, defined at linux/jiffies.h, which deal
with wrapping correctly and are nicer to read.
Signed-off-by: Marcelo Feitoza Parisi <marcelo@feitoza.com.br>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Marcelo Feitoza Parisi <marcelo@feitoza.com.br>
Use of the time_after() macro, defined at linux/jiffies.h, which deal
with wrapping correctly and are nicer to read.
Signed-off-by: Marcelo Feitoza Parisi <marcelo@feitoza.com.br>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
tr_type_trans(), hippi_type_trans() left as-is.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the protocol specific config options out to the specific protocols.
With this change net/Kconfig now starts to become readable and serve as a
good basis for further re-structuring.
The menu structure is left almost intact, except that indention is
fixed in most cases. Most visible are the INET changes where several
"depends on INET" are replaced with a single ifdef INET / endif pair.
Several new files were created to accomplish this change - they are
small but serve the purpose that config options are now distributed
out where they belongs.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new top-level menu named "Networking" thus moving
net related options and protocol selection way from the drivers
menu and up on the top-level where they belong.
To implement this all architectures has to source "net/Kconfig" before
drivers/*/Kconfig in their Kconfig file. This change has been
implemented for all architectures.
Device drivers for ordinary NIC's are still to be found
in the Device Drivers section, but Bluetooth, IrDA and ax25
are located with their corresponding menu entries under the new
networking menu item.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers should do this:
.suspend()
pci_disable_device()
.resume()
pci_enable_device()
http://bugzilla.kernel.org/show_bug.cgi?id=3469
Signed-off-by: David Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This is part of the grand scheme to eliminate the qlen
member of skb_queue_head, and subsequently remove the
'list' member of sk_buff.
Most users of skb_queue_len() want to know if the queue is
empty or not, and that's trivially done with skb_queue_empty()
which doesn't use the skb_queue_head->qlen member and instead
uses the queue list emptyness as the test.
Signed-off-by: David S. Miller <davem@davemloft.net>
As a follow-up, remove the inclusion of pcmcia/version.h in many files.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the "event handler" to struct pcmcia_driver -- the unified event handler
will disappear really soon, but switching it to struct pcmcia_driver in the
meantime allows for better "step-by-step" patches.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Few more u32 vs. pm_message_t fixes.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for some new PHY models to sungem as used on some
recent Apple iMac G5 models.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This converts the usage of struct of_match to struct of_device_id,
similar to pci_device_id. This allows a device table to be generated,
which can be parsed by depmod(8) to generate a map file for module
loading.
In order for hotplug to work with macio devices, patches to
module-init-tools and hotplug must be applied. Those patches are
available at:
ftp://ftp.suse.com/pub/people/jeffm/linux/macio-hotplug/
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Dave, you were right and the sleeping locks in shaper were
broken. Markus Kanet noticed this and also tested the patch below that
switches locking to spinlocks.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for ethtool -C with verification of user parameters.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Nicolas Pitre
Those are big, slow and generally not recommended for kernel code.
They are even not present on i386. So it should be concluded that
one could as well get away with do_div() alone.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Many drivers use skb->tail unnecessarily.
In these situations, the code roughly looks like:
dev = dev_alloc_skb(...);
[optional] skb_reserve(skb, ...);
... skb->tail ...
But even if the skb_reserve() happens, skb->data equals
skb->tail. So it doesn't make any sense to use anything
other than skb->data in these cases.
Another case was the s2io.c driver directly mucking with
the skb->data and skb->tail pointers. It really just wanted
to do an skb_reserve(), so that's what the code was changed
to do instead.
Another reason I'm making this change as it allows some SKB
cleanups I have planned simpler to merge. In those cleanups,
skb->head, skb->tail, and skb->end pointers are removed, and
replaced with skb->head_room and skb->tail_room integers.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Now we can change the pci core to always set this pointer, as pci drivers
should use it, not the driver core callback.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
More fixes for greg depredations.
Also nuke lots of pointless typecasts.
All this new wireless code adds near-infinite amounts of trailing whitespace.
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
