A powerpc ppc64_defconfig build produces these warnings:
kernel/trace/ring_buffer.c: In function 'rb_add_time_stamp':
kernel/trace/ring_buffer.c:969: warning: format '%llu' expects type 'long long unsigned int', but argument 2 has type 'u64'
kernel/trace/ring_buffer.c:969: warning: format '%llu' expects type 'long long unsigned int', but argument 3 has type 'u64'
kernel/trace/ring_buffer.c:969: warning: format '%llu' expects type 'long long unsigned int', but argument 4 has type 'u64'
Just cast the u64s to unsigned long long like we do everywhere else.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The pages of a buffer was originally pointing to the page struct, it
now points to the page address. The freeing of the page still uses
the page frame free "__free_page" instead of the correct free_page to
the address.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch replaces the local_irq_save/restore with preempt_disable/
enable. This allows for interrupts to enter while recording.
To write to the ring buffer, you must reserve data, and then
commit it. During this time, an interrupt may call a trace function
that will also record into the buffer before the commit is made.
The interrupt will reserve its entry after the first entry, even
though the first entry did not finish yet.
The time stamp delta of the interrupt entry will be zero, since
in the view of the trace, the interrupt happened during the
first field anyway.
Locking still takes place when the tail/write moves from one page
to the next. The reader always takes the locks.
A new page pointer is added, called the commit. The write/tail will
always point to the end of all entries. The commit field will
point to the last committed entry. Only this commit entry may
update the write time stamp.
The reader can only go up to the commit. It cannot go past it.
If a lot of interrupts come in during a commit that fills up the
buffer, and it happens to make it all the way around the buffer
back to the commit, then a warning is printed and new events will
be dropped.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove the global head and tail indexes and move them into the
page header. Each page will now keep track of where the last
write and read was made. We also rename the head and tail to read
and write for better clarification.
This patch is needed for future enhancements to move the ring buffer
to a lockless solution.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
My original patch had a compile bug when NUMA was configured. I
referenced cpu when it should have been cpu_buffer->cpu.
Ingo quickly fixed this bug by replacing cpu with 'i' because that
was the loop counter. Unfortunately, the 'i' was the counter of
pages, not CPUs. This caused a crash when the number of pages allocated
for the buffers exceeded the number of pages, which would usually
be the case.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix:
kernel/trace/ring_buffer.c: In function ‘rb_allocate_pages’:
kernel/trace/ring_buffer.c:235: error: ‘cpu’ undeclared (first use in this function)
kernel/trace/ring_buffer.c:235: error: (Each undeclared identifier is reported only once
kernel/trace/ring_buffer.c:235: error: for each function it appears in.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The current method of overlaying the page frame as the buffer page pointer
can be very dangerous and limits our ability to do other things with
a page from the buffer, like send it off to disk.
This patch allocates the buffer_page instead of overlaying the page's
page frame. The use of the buffer_page has hardly changed due to this.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The old "lock always" scheme had issues with lockdep, and was not very
efficient anyways.
This patch does a new design to be partially lockless on writes.
Writes will add new entries to the per cpu pages by simply disabling
interrupts. When a write needs to go to another page than it will
grab the lock.
A new "read page" has been added so that the reader can pull out a page
from the ring buffer to read without worrying about the writer writing over
it. This allows us to not take the lock for all reads. The lock is
now only taken when a read needs to go to a new page.
This is far from lockless, and interrupts still need to be disabled,
but it is a step towards a more lockless solution, and it also
solves a lot of the issues that were noticed by the first conversion
of ftrace to the ring buffers.
Note: the ring_buffer_{un}lock API has been removed.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The raw_local_irq_save causes issues with lockdep. We don't need it
so replace them with local_irq_save.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Mathieu Desnoyers pointed out that the freeing of the page frame needs
to be reset otherwise we might trigger BUG_ON in the page free code.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If for some strange reason the buffer_page gets bigger, or the page struct
gets smaller, I want to know this ASAP. The best way is to not let the
kernel compile.
This patch adds code to test the size of the struct buffer_page against the
page struct and will cause compile issues if the buffer_page ever gets bigger
than the page struct.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This is a unified tracing buffer that implements a ring buffer that
hopefully everyone will eventually be able to use.
The events recorded into the buffer have the following structure:
struct ring_buffer_event {
u32 type:2, len:3, time_delta:27;
u32 array[];
};
The minimum size of an event is 8 bytes. All events are 4 byte
aligned inside the buffer.
There are 4 types (all internal use for the ring buffer, only
the data type is exported to the interface users).
RINGBUF_TYPE_PADDING: this type is used to note extra space at the end
of a buffer page.
RINGBUF_TYPE_TIME_EXTENT: This type is used when the time between events
is greater than the 27 bit delta can hold. We add another
32 bits, and record that in its own event (8 byte size).
RINGBUF_TYPE_TIME_STAMP: (Not implemented yet). This will hold data to
help keep the buffer timestamps in sync.
RINGBUF_TYPE_DATA: The event actually holds user data.
The "len" field is only three bits. Since the data must be
4 byte aligned, this field is shifted left by 2, giving a
max length of 28 bytes. If the data load is greater than 28
bytes, the first array field holds the full length of the
data load and the len field is set to zero.
Example, data size of 7 bytes:
type = RINGBUF_TYPE_DATA
len = 2
time_delta: <time-stamp> - <prev_event-time-stamp>
array[0..1]: <7 bytes of data> <1 byte empty>
This event is saved in 12 bytes of the buffer.
An event with 82 bytes of data:
type = RINGBUF_TYPE_DATA
len = 0
time_delta: <time-stamp> - <prev_event-time-stamp>
array[0]: 84 (Note the alignment)
array[1..14]: <82 bytes of data> <2 bytes empty>
The above event is saved in 92 bytes (if my math is correct).
82 bytes of data, 2 bytes empty, 4 byte header, 4 byte length.
Do not reference the above event struct directly. Use the following
functions to gain access to the event table, since the
ring_buffer_event structure may change in the future.
ring_buffer_event_length(event): get the length of the event.
This is the size of the memory used to record this
event, and not the size of the data pay load.
ring_buffer_time_delta(event): get the time delta of the event
This returns the delta time stamp since the last event.
Note: Even though this is in the header, there should
be no reason to access this directly, accept
for debugging.
ring_buffer_event_data(event): get the data from the event
This is the function to use to get the actual data
from the event. Note, it is only a pointer to the
data inside the buffer. This data must be copied to
another location otherwise you risk it being written
over in the buffer.
ring_buffer_lock: A way to lock the entire buffer.
ring_buffer_unlock: unlock the buffer.
ring_buffer_alloc: create a new ring buffer. Can choose between
overwrite or consumer/producer mode. Overwrite will
overwrite old data, where as consumer producer will
throw away new data if the consumer catches up with the
producer. The consumer/producer is the default.
ring_buffer_free: free the ring buffer.
ring_buffer_resize: resize the buffer. Changes the size of each cpu
buffer. Note, it is up to the caller to provide that
the buffer is not being used while this is happening.
This requirement may go away but do not count on it.
ring_buffer_lock_reserve: locks the ring buffer and allocates an
entry on the buffer to write to.
ring_buffer_unlock_commit: unlocks the ring buffer and commits it to
the buffer.
ring_buffer_write: writes some data into the ring buffer.
ring_buffer_peek: Look at a next item in the cpu buffer.
ring_buffer_consume: get the next item in the cpu buffer and
consume it. That is, this function increments the head
pointer.
ring_buffer_read_start: Start an iterator of a cpu buffer.
For now, this disables the cpu buffer, until you issue
a finish. This is just because we do not want the iterator
to be overwritten. This restriction may change in the future.
But note, this is used for static reading of a buffer which
is usually done "after" a trace. Live readings would want
to use the ring_buffer_consume above, which will not
disable the ring buffer.
ring_buffer_read_finish: Finishes the read iterator and reenables
the ring buffer.
ring_buffer_iter_peek: Look at the next item in the cpu iterator.
ring_buffer_read: Read the iterator and increment it.
ring_buffer_iter_reset: Reset the iterator to point to the beginning
of the cpu buffer.
ring_buffer_iter_empty: Returns true if the iterator is at the end
of the cpu buffer.
ring_buffer_size: returns the size in bytes of each cpu buffer.
Note, the real size is this times the number of CPUs.
ring_buffer_reset_cpu: Sets the cpu buffer to empty
ring_buffer_reset: sets all cpu buffers to empty
ring_buffer_swap_cpu: swaps a cpu buffer from one buffer with a
cpu buffer of another buffer. This is handy when you
want to take a snap shot of a running trace on just one
cpu. Having a backup buffer, to swap with facilitates this.
Ftrace max latencies use this.
ring_buffer_empty: Returns true if the ring buffer is empty.
ring_buffer_empty_cpu: Returns true if the cpu buffer is empty.
ring_buffer_record_disable: disable all cpu buffers (read only)
ring_buffer_record_disable_cpu: disable a single cpu buffer (read only)
ring_buffer_record_enable: enable all cpu buffers.
ring_buffer_record_enabl_cpu: enable a single cpu buffer.
ring_buffer_entries: The number of entries in a ring buffer.
ring_buffer_overruns: The number of entries removed due to writing wrap.
ring_buffer_time_stamp: Get the time stamp used by the ring buffer
ring_buffer_normalize_time_stamp: normalize the ring buffer time stamp
into nanosecs.
I still need to implement the GTOD feature. But we need support from
the cpu frequency infrastructure. But this can be done at a later
time without affecting the ring buffer interface.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
