free_irq() calls synchronize_irq() for you, so there is no need for
drivers to manually do the same thing (again). Thus, calls where
sync-irq immediately precedes free-irq can be simplified.
However, during this audit several bugs were noticed, where free-irq is
preceded by a "irq >= 0" check... but the sync-irq call is not covered
by the same check.
So, where sync-irq could not be eliminated completely, the missing check
was added.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The last ALC889A hack may break on some devices with certain model presets
since patch_alc*() have different model tables. So, now it's handled in
the original patch_alc882() but fly to patch_alc883() in model=auto
appropriately.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Several 92hd7xxx and STAC9228 laptops have multiple headphone jacks,
the second headphone jack should be used for the 5.1 surround sound.
Add support for 'Headphone as Line Out' switch, which allows it be used
in 5.1 surround sound.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the support of AD1989A and AD1989B codecs.
These codecs can have multiple SPDIF devices, but currently we handle
only one SPDIF. If any real devices with two SPDIF interfaces (likely
one for SPDIF and one for HDMI), we'll fix this rightly.
Otherwise, these codecs are pretty similar with AD1988.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds support for Quanta IL1 mini-notebook to alsa, defining a new model
for it. It comes with an ALC267 codec chip. Some notes about this model:
* In headphone automute, I use AC_VERB_SET_PIN_WIDGET_CONTROL instead of common
amp mute, to avoid conflict with mixer switch (mixer and automute use the
same nid).
* The only connected capture sources in the hardware are the internal mic and
external mic jack. So instead of using an input source selector like on other
ALC268 models, the mic automute automatically switch between captures.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Power management support for EAPD enabled laptops, when headphones
are sensed it pulls the EAPD GPIO line low to power it down.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Several laptops have have the SPDIF out defined as 'Digital other out'
when it should be 'SPDIF out' in the default config.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The legacy PC speaker signal was not routed to outputs. The codec is not
prevented from powering down in this patch, although I suppose one could
argue that perhaps it should be. Let me know if anyone feels strongly one
way or the other.
Signed-off-by: Tony Vroon <tony@linx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Please refer to [0003874] on the alsa mantis.
This patch added the pci quirk.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To mute the output of Pin widget 15 in ALC880, we should use the
HDA_OUTPUT. However, current code looks like :
snd_hda_codec_amp_stereo(codec, 0x15, HDA_INPUT, 0, HDA_AMP_MUTE, bits);
It may be a misspelling.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Please refer to [0003848] on the alsa mantis.
This patch adds the pci quirk and Mic-Int controller.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for mic automute in clevo-m720r ALC883 model, and rename it
to more generic clevo-m720. Also change model entry in ALSA-Configuration.txt
accordingly.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Forgot one more: 3stack-hp model also have now the same mixer as
3stack-6ch (after DAC assignment fix in ALC883), so use it avoiding
duplicating the same mixer definition.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After DAC assignment fix in ALC883, alc888_6st_dell_mixer is now the
same as alc883_base_mixer. Avoid duplicated code and use
alc883_base_mixer in 6stack-dell model, removing alc888_6st_dell_mixer
definition.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After DAC assignment fix in ALC883, the 6stack-hp model is now the same
as 6stack-dig. So just remove 6stack-hp model and replace its use with
6stack-dig.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Keep the format verb at closing PCM streams.
Introduced snd_hda_codec_cleanup_stream() for the parcicular purpose.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Actually clfe and surround DACs are inverted in alc883_dac_nids array
(see ALC883 datasheet). I discovered this while testing multi-channel
setup (using 3stack-6ch-dig model) on MSI 945GCM5 V2 motherboard that
has an ALC883 codec. Simply Rear Left/Right and Center/LFE were swapped
in 6 channel mode (also in 4 channel mode you didn't get rear left/right
output). Other models also were affected by this bug, as can be seen by
the mixer layouts that "workaround" this (the real bug was not noticed,
and some other models simply played with mixer and initial verbs). Thus
along with fixing the order of dac nids, also change the models that
relied on previous dac ordering properly.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The docking station headphone output had no audio and jack sense
was not considered.
Jack information from the laptop itself and the dock are combined, as
the dock does not obscure the connector.
Signed-off-by: Tony Vroon <tony@linx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The hda-intel driver has a problem at power-off on ASUS P5AD2.
It's caused when the position-buffer is enabled -- most likely a
hardware-specific problem.
This patch adds a quirk to avoid the unnecessary enablement of
position-buffer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Map 3stack-6ch-dig ALC662 model for Asus P5GC-MX.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently ALC662 doesn't suport amp mute for AmpOut in nids 0x02, 0x03,
0x04 (see block diagram in ALC662 datasheet page 3, does M correspond to
mute?). The result is that currently mute for "Front Playback Switch",
"Surround Playback Switch", "Center Playback Switch" and "LFE Playback
Switch" mixer items doesn't work (tested on Asus P5GC-MX motherboard
with 3stack-6ch model).
The solution I found for this is to mute the proper inputs in 0x0c,
0x0d, 0x0e audio mixers.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, the headphone controls are created as Master wrongly in
some cases, and this prevents the virtual master controls.
The patch fixes the problem by simply using "Headphone" always for
headphone controls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixed issue on some laptops that if the Master mixer and DAC mixers are
turned all the way up that will cause distortion. This is fixed by limiting
the max volume with the volume knob nid.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Improved ALC262 ultra model for Samsung Q1 Ultra series.
- clean up mixers
- support of input from HP jack as a mic
- add quirk for Q1 EL
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The default capture source should be the mic which is 0x01 on this model.
In addition to that the change to VREF50 allows for higher capture volume.
Signed-off-by: Michael Gruber <lists.mg@googlemail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Changed so that internal speakers point to the Front mixer instead of Surround.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for the Toshiba Equium L30 laptop and renames the mixer
controls to match Laptop usages.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the internal mic as a capture source item for ALC268 acer model.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the Device IDs of nvidia MCP79 HD audio controller to hda_intel.c
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently the model laptop-hpsense use the 0x12 as ExtMic,
and use 0x14 as Internal IntMic.
But the hp530 only have one ExtMic, the Pin widget is 0x14.
In this patch, I changed the mixer item for them.
I still reserved the IntMic item, it will be helpful if
other machine may use this model.
ALSA bug#3821.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is no suitable model for Pi2515.
This model is to support it. ALSA bug#3800.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
NEC S970 has no sound in the internal speakers when autodetection is
used.
With targa-dig model, there is sound in the speakers and it gets
correctly muted when pluging headphones.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is no suitable model for M720R (ALSA bug#3781).
This patch is to support HP jack-sensing and mixer.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sparc32:
sound/pci/hda/hda_intel.c: In function 'azx_create':
sound/pci/hda/hda_intel.c:1838: error: 'DMA_64BIT_MASK' undeclared (first use in this function)
sound/pci/hda/hda_intel.c:1838: error: (Each undeclared identifier is reported only once
sound/pci/hda/hda_intel.c:1838: error: for each function it appears in.)
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added core_init[] for several 92hd73xxx laptops.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Power management can't be enabled on fixed ports, since the presence
will always return false and prevent output.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the array declaration to hda_codec.c where it is used and add includes
where the individual presets are declared.
Fixes the following sparse warnings:
sound/pci/hda/patch_realtek.c:13744:25: warning: symbol 'snd_hda_preset_realtek' was not declared. Should it be static?
sound/pci/hda/patch_cmedia.c:729:25: warning: symbol 'snd_hda_preset_cmedia' was not declared. Should it be static?
sound/pci/hda/patch_analog.c:3656:25: warning: symbol 'snd_hda_preset_analog' was not declared. Should it be static?
sound/pci/hda/patch_sigmatel.c:3995:25: warning: symbol 'snd_hda_preset_sigmatel' was not declared. Should it be static?
sound/pci/hda/patch_si3054.c:286:25: warning: symbol 'snd_hda_preset_si3054' was not declared. Should it be static?
sound/pci/hda/patch_atihdmi.c:156:25: warning: symbol 'snd_hda_preset_atihdmi' was not declared. Should it be static?
sound/pci/hda/patch_conexant.c:1721:25: warning: symbol 'snd_hda_preset_conexant' was not declared. Should it be static?
sound/pci/hda/patch_via.c:1962:25: warning: symbol 'snd_hda_preset_via' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Temp variable in the loop shadows the second argument (which is otherwise
unused in this function). Change this to defcfg as it is used to hold
the default config.
sound/pci/hda/patch_sigmatel.c:2759:18: warning: symbol 'cfg' shadows an earlier one
sound/pci/hda/patch_sigmatel.c:2734:26: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added logic to check if AUTO_PIN_FRONT_MIC is available for output
switch, if AUTO_PIN_MIC isn't.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some laptops have a internal analog microphone that is not setup by the BIOS.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added PCI_QUIRKS for laptop that have the 92HDxxx family of codecs.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
STAC_DELL_BIOS quirks were setting the association value wrong
for port 0x0f, which prevented it from being included in hp_outs[].
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix issue on STAC927x codecs that first DAC was getting powered down
even if was being used.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Initialize the capture source properly for auto model.
It's especially important for cases that only mic is detected.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the beep volume control to ALC268 codec support code.
Since the codec doesn't return the correct AMP caps, we need to override
the value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use a private array for TLV entries of virtual master controls instead
of (supposed) static array. This cleans up the existing codes.
Also, now vmaster assumes the simple dB-range TLV that is the only type
it can handle.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the codes for virtual master controls to sound core part so that
not only hda-intel drivers can use it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the support of new AD codecs: AD1883, AD1884A, AD1984A and AD1984B.
These are almost compatible except for additional digital pins, etc.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC262 must have capsrc_nids defined as well as in ALC882.
Also, add a NULL check in alc882_mux_enum_put to avoid Oops.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The last patch for fixing the auto-config pin setting breaks the resume
due to a wrong use of snd_hda_codec_amp_stereo(). The code in the init
hook shouldn't touch the amp cache.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added a new mixer switch to enable/disable the sharing of the default
PCM stream with analog and SPDIF outputs. When "IEC958 Default PCM"
switch is on, the PCM stream is routed both to analog and SPDIF outputs.
This is the behavior in the earlier version.
Turning this switch off has a merit for some codecs, though. Some codec
chips don't support 24bit formats for SPDIF but only for analog outputs.
In this case, you can use 24bit format by disabling this switch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes some bugs in the auto-configurator of Realtek codecs:
- add missing pin set-up for speaker pins
- fix the speaker auto-mute function not to conflict with the existing
"Speaker" mixer switch
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In some cases, the BIOS sets up only the HP pins with different assoc
and sequence numbers, e.g. on FSC Esprimo with ALC262.
This patch adds a fix-up for such a case. When multiple HPs are defined
and no line-outs is found, the configurator tries to re-assign some pins
from HP list to line-out, judging from the sequence number.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Implemented the auto-mic jack sensing for Samsung laptops with AD1986A
codec chip (model=laptop-eapd).
The hardware uses pin 0x1d and 0x1f for the internal and external
mics, respectively.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clean up the codes of the capture source selection for Realtek codecs.
Now using common helper functions with the new capsrc_nids field.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reprogram the speaker-pin setting at each HP pin plug to make sure
the spekaer auto-muting on AD1981HD hp model.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I've just noticed that there are a handful of duplicate controls in the
ALC268 test model mixer. This patch (against alsa-driver 1.0.16) removes
them.
Signed-off-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HD-audio hardware usually supports 64bit address for DMA and other
buffers. The patch enables the feature if supported.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On several laptops that have STAC9228 codecs have unused DACs,
this powers them down to a D3 state.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the current scheme, PCM device numbers are assigned incrementally
in the order of codecs. This causes problems when the codec number
is irregular, e.g. codec #0 for HDMI and codec #1 for analog. Then
the HDMI becomes the first PCM, which is picked up as the default
output device. Unfortuantely this doesn't work well with normal
setups.
This patch introduced the fixed device numbers for the PCM types,
namely, analog, SPDIF, HDMI and modem. The PCM devices are assigned
according to the corresponding PCM type. After this patch, HDMI will
be always assigned to PCM #3, SPDIF to PCM #1, and the first analog
to PCM #0, etc.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current code doesn't allow multiple SPDIF devices, and causes
errors when multiple SPDIF devices are found (e.g. SPDIF out and HDMI).
This patch allows multiple SPDIF devices by incrementing the index
automatically.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for the OQO Model 2 Ultra Mobile PC.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the line-out volume control of eeepc p701 to be a proper slave of
the virtual master control.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some models like eeepc ep20 have invalid mixer names that aren't
handled properly by virtual master controls. Rename them to the
proper names.
Also fixed some typos in the mixer names but they are not compiled
in right now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds a quirk to the Realtek ALC883 table for the Albatron KI690-AM2
motherboard to use the 6stack-dig model.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP dv8000 laptop has a problem with Master volume. It's due to the
connection of the widget 0x13. When it's connected from the analog
amp mixer (0x19), it works as expected mysteriously (ALSA bug#3775):
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3775
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver gets Oops with ATI HDMI devices due to the wrong calculation
of index for playback streams. This patch fixes it. Reference:
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3746
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pin widgets have always one amp-input value regardless of number of
connections. The proc file showed values wrongly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The capture source selection for ADC list with two elements is buggy
becaues of a wrong capture mux list. This patch fixes the starting
index based on spec->num_adc_nids.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The widget list of capture source selection for ALC883 contains the
wrong NIDs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't create vmaster controls if no slaves are found in the given list.
This prevents the error due to an empty vmaster control.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixed the SPDIF output on Conexant Cx5045 codec. Added the missing
pin output setting and fixed the wrong NID for digital audio-out widget.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some laptop has an internal analog microphone that is 'fixed'.
This patch prevents creating a 'Mic In as Output' switch for
ports that can't be outputs.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds support for Intel's SCH mobile chipset.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Support added for detecting HP jack presence via GPIO on several laptop docks.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the support for Dell T3400 with AD1984 codec chip.
ALSA bug#3699:
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3699
Signed-off-by: Douglas Kosovic <douglask@itee.uq.edu.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add SPDIF playback switch to the slave element list so that it
can be toggled via the master control as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds the Intel ICH10 HD Audio Controller DeviceID's.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the speaker-automute function to ALC262 HP models.
Also, 'Mono' mixer elements are renamed as more intuitive 'Speaker'.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Removed the PCM mixer elements conflicting with others.
Also renamed Master control to Headphone, which isn't a real master.
(The Master control is still created as a virtual master even after
this rename.)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The PCM mixer elements in HP T5735 model of ALC262 codec conflict
with Speaker and Headphone volumes. They should be removed.
Ditto for LineOut that is identical with Speaker.
Also, fixed/cleaned up the auto-mute callback to use the amp cache
correctly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Renamed the non-standard mixer elements 'iSpeaker' to 'Speaker'
in Realtek codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The SPDIF output on AD1986A laptop-eapd model is disabled although
some Samsung laptops have SPDIF output. Enable it after checking the
pin default config.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The AD codecs have hardware SPDIF volume/switch controls but they
are not assigned to the slave list for virtual master controls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch checks to see the Line In/Mic port have the ability
to do output before creating the the control switches.
The 92hd71bxx series of codecs has this issue with the port 0xe,
which only allows input.
Signed-off-by: Matthew Ranostay <mranostay@embededalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Simplify usage of the Acer Aspire 5310 laptop with the ALC268 based codec
sound card via add correct PCI SSID.
Signed-off-by: Andy Shevchenko <andy@smile.org.ua>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the support for Conexant 5051 audio codec.
Right now there are two preset models, laptop and hp.
The whole patch is based on the information from the base patch by
Linuxant.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Simplify usage of the Acer Aspire 5315 laptop with the ALC268 based codec
sound card via add correct PCI SSID.
Signed-off-by: Andy Shevchenko <andy@smile.org.ua>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fixed issue that the incorrect GPIO line was being pulled high
for some STAC9205 based laptops.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fixed the bug that multiple capture streams conflict on Realtek codec
routines.
Also, this adds a framework to enable the alternative playback stream,
e.g. for VoIP. It's not fully implemented yet, though.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Allows for dynamically creating mono out mixer controls and well
as mono mux controls.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added a mono_out_pin field to autocfg struct, and code to parse
for the mono_out_line.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Don't query a widget parameter for an invalid NID in get_wcaps() but
rather returns zero (i.e. no attribute).
The read to an non-existing widget may result in a fatal codec
communication error.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Don't read the widget list again as we already have it at the beginning.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added afg and mfg preset masks for more finer codec-preset selection.
Signed-off-by: Marc Boucher <marc@linuxant.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added a delay after the power state change as a partial workaround
for 'hda_intel: azx_get_response timeout' problem on Cxt codecs.
Signed-off-by: Marc Boucher <marc@linuxant.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The input volume/switch elements are missing in Cxt5047 test model.
Also the patch includes some code clean ups.
Signed-off-by: Marc Boucher <marc@linuxant.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Change laptop models to three different models, laptop-hpsense,
laptop-micsense and laptop-hpmicsense. The first two correspond to
the old 'laptop' and 'fujitsu' models.
Reassigned the quirk table for the new models.
Signed-off-by: Marc Boucher <marc@linuxant.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add support for the mono mux on several 92HD7xxx codecs.
Creates a dynamic mixer for the mux selection.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
In azx_[rirb_]get_response(), the timeout is checked at the end of the loop.
It's better to be checked just after the check of the RIRB index to avoid
a bogus error with a too long msleep().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds additional output to the /proc codec#X info.
The following pieces of information are added to the output:
- Balanced, L/R swap, trigger, impedance sense pin capabilities
- Vref pin capabilities
- Current Vref pin widget control setting
- Default configuration association, sequence, and misc bit test
- EAPD/BTL bits conveying balanced mode, EAPD, and L/R swap
- Power state modified to show state name as well as setting vs actual value
- GPIO parameter output on Audio Function Group, including enumeration of IO
pins which are indicated present (Any I and O pins are not output at this
time)
- Stripe and L/R swap widget capabilities
- All digital converter bits: enable, validity, validity config, preemphasis,
copyright, non-audio, professional, generation level, and content category
- Converter stream and channel values for in/out widgets
- SDI select value for in widgets
- Unsolicited response widget capability tag and enabled bit
- Delay widget capability value
- Processing widget capability benign bit and number of coefficients
- Realtek Define Registers: processing coefficient, coefficient index
[Also, fixed space/tab issues and make codes a bit more readable
-- Takashi]
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
For codec conexant 5045, I found that the name of 'Capture Source Items'
is different from the name of mixer.
The mixer is:
HDA_CODEC_VOLUME('Ext Mic Playback Volume', 0x17, 0x2, HDA_INPUT),
HDA_CODEC_MUTE('Ext Mic Playback Switch', 0x17, 0x2, HDA_INPUT),
But the capture source item is :
static struct hda_input_mux cxt5045_capture_source = {
.num_items = 2,
.items = {
{ 'IntMic', 0x1 },
{ 'LineIn', 0x2 },
}
};
I think that it's better to change the name of capture_source to avoid
misunderstanding.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The benq r55e laptop have 3 jacks on the front panel.
One for HP, one for Line In and one for Mic In.
This patch implemented a new model to support it.
Signed-off-by: Jiang Zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Codec with id 11c1:1040 sitting on hda bus isn't si3054-compatible.
It should be removed from patch_si3054.c id list.
The detailed information
http://archives.linmodems.org/26457
From: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Some machines with STAC codecs seem to have problems (e.g. no audible
playback) when the delay in codec-read routine is too short.
I still don't figure out which command sequence causes this problem
(due to lack of test hardware), but it's known that increasing the
delay fixes. So, added a stupid workaround here temporarily...
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Enable the SPDIF input-pin on VIA codecs when SPDIF-input is enabled
by BIOS. Also, including a bit code clean up.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the support of Dell OEM laptops (Vostro 1200) with ALC268 codec.
The new model=dell is provided.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
It turned out that the PCBEEP element (0x1d) is disabled on some hardwares
although it's defined in the datasheet. Because of the error at info of
this element, the mixer gets totally unusable.
Since the PCBEEP isn't that important feature, it's safer to disable this.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
There are two similar GPIO-enablement codes in patch_sigmatel.c.
Let's clean up.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch removes hardcoded values for the number of streams supported
by the southbridge in most chipsets, and reads these values from the
chipset directly. Most systems are hardwired for 4 streams in each
direction, but newer chipsets change that capability.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch fixes 5.1 surround output and headphone detection in the
Dell Inspiron 530 and possibly other Dell systems using the ALC888
codec (mode 6stack-dell).
Signed-off-by: Claudio Matsuoka <cmatsuoka@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fixes multiple device support by incrementing the static device counter
at the end of the azx_probe() call. Without this, subsequent probes would
always use the index specified for the first card.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The ALC auto-probe creates mic boost controls automatically for the
probed pins, but it assumes that they are analog mics. The digital
mics have no boost controls and must be skipped.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Print the name of the defect controls in error messages in amp info
callback. This will make debugging easier.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added a new STAC 9205 quirk for Vostro 1500.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added support for advanced power management support for output ports on
92HD7xxx family of codecs. Inactive output ports are powered down when
the pin sense doesn't detect a connection, and powered back up when a
connection is sensed.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add master controls using vmaster to codecs that have no real hardware
master volume registers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added helper functions to implement virtual master volume controls.
The virtual master control is a control element that has multiple
slave controls. The value of master element is equally added to
slave elements.
The functions are written for general purpose, but it's put in the
HD-audio directory as now, since HD-audio driver is the only user.
It should be moved to the common place once after other drivers use
vmaster.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Moved 2 systems PCI_QUIRK values to STAC_DELL_BIOS. Also the second
front HP jack is incorrect defined in the BIOS VT's for some laptops,
this patch corrects this.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Please refer to the [0003680] on ALSA bugtracking system.
The user found that 'model=mbp3' works and provided the ID.
From: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
1. Support HP rp5700
2. Fixed alc_subsystem_id function (Bug fixed and support Desktop)
3. Support ASUS EP20
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added a mono output mute mixer for the 92hd71bxx family of codecs, this
also removes the need for the mono out node to explicitly unmuted in the
core init.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This header file exists only for some hacks to adapt alsa-driver
tree. It's useless for building in the kernel. Let's move a few
lines in it to sound/core.h and remove it.
With this patch, sound/driver.h isn't removed but has just a single
compile warning to include it. This should be really killed in
future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the proper model=laptop for HP 350 laptop with Cxt5045 codec.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This implements a test model for the ALC268. It depends on the feature
added by alc260-test-eapd-0.2.diff. This patch also adds a mention of
the ALC260 test model to ALSA-Configuration.txt since this seems to have
been missed.
Signed-off-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This implements a switch control for the EAPD signal output by the ALC26x
chips. Since some laptops may utilise this to activate useful things it
is handy to have a control for this in the ALC26x test models. The patch
includes the control in the ALC260 test model.
Signed-off-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Dynamically create digital gain mixers for dmics that have out-amp
support. Also some 92HD73xx's codecs don't have DMIC gains, so this also
prevents creating dead mixers.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
It turned out that there can be multiple HD-audio devices on a single
machine (e.g. on-board audio and HDMI on graphic cards), so we need to
support multiple devices with snd-hda-intel driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds IEC958 digital out support for the AD1984 sound card.
This card can be found in Lenovo Thinkapds T61/X61. The digital out is
not located on the Thinkpad, but optional docking station (it's coxial
digital out). I've add this support as it is done the exact same way
for the AD1983 & AD1884.
I have tested this patch with my Lenovo Thinkpad T61 hooked up to a
docking station (that has the digital coxial) and then run to my home
theater reciever. Works like a charm :-)
Signed-off-by: Jerone Young <jerone@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Some laptops incorrectly assume the front input jack as a line in
instead of a microphone in. Which in turn disables the voltage
reference, in which non-amplified input is not possible. This patch
enables VREF80 for the input jack.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Sort the ad1986a config table by PCI SSID (the last toshiba entry was
added wrongly).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
According to the [0003659], the node 0x23,0x24 is a selector.
I checked the alc268 spec on the REALTEK website and it showed that they
were selectors indeed.
However, current code implement the alc268 input_mux in a mixer way.
Signed-off-by: Jiang Zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The model laptop-eapd get rid of the high-pitched noise.
(ALSA bug#3662)
Signed-off-by: Jiang Zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The commit that added support for ASUS P701 eeepc also changed the
mixers of other ALC662 models, duplicating entries for the Capture
items, making them to not work anymore. This fixes it by removing
duplicated entries using where possible the common alc662_capture_mixer.
Also alc662_capture_mixer should use alc662* functions and not alc882
(I checked /proc/asound/card0/codec* on an eepc model and it's ok).
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added AC_VERB_GET_DIGI_CONVERT_2 and renamed AC_VERB_GET_DIGI_CONVERT to
AC_VERB_GET_DIGI_CONVERT_1 to stay consistent with the SET variants. Added
AC_VERB_GET_GPIO_UNSOLICITED_RSP_MASK, AC_VERB_SET_GPIO_UNSOLICITED_RSP_MASK,
and AC_PINCAP_LR_SWAP. The missing fields were listed in the ALC883 datasheet
rev 1.3.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The digital mux on STAC codecs doesn't always exist although the
driver builds dmux enum mixer elements unconditionally.
Now the driver creates 'digital input source' mixer elements only
when dmux is available.
Also, the patch adds the missing dmux definition for STAC925x.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Sort pci quirk list in the order of PCI SSID.
This makes easier to find out the buggy duplicated entries.
Thanks to Andy Shevchenko for providing the sort script.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The PCM volume of Cx5045 codec has overload that isn't useful but
rather harmful. Add a hack to override the amp info to set the max
level 0 dB.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Cleaned up STAC927x and added several subsystem id's for more laptops.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
AC_KNBCAP_DELTA is incorrectly defined as (1<<8). According to the Intel
HDA spec, this is bit 7 after AC_KNBCAP_NUM_STEPS which is a 0x7f mask.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added more codecs to the 92HD71 family, as well as support for several
that don't have an analog mixer.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Changed hardware gain mixers for the digital mic's from HDA_OUTPUT to
HDA_INPUT.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Enable Analog CD Input from internal ATAPI connector on Asus M2N-SLI.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added support for new STAC92HD73 family of codecs. Additionally added
features for multiple analog loopbacks, and multiple dmux mixers.
Regression testing for the analog loopback changes for STAC9205 and
STAC9274D completed with any issues, as well for the dmux changes.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The attached patch adds initial support of the Mitac 8252D
(http://www.mitac-mtc.com.tw/English/products/8252Dspec.htm).
Working:
- Front speakers (volume + mute)
- Center/LFE speakers (volume + mute)
- HP out (with Front Volume)
- HP individual mute switch
- HP Jack sense
- Front Mic and its volume
Not tested:
- external mic and its volume
Not working while now:
- Mic Jack sense
Questionable:
- is Mic have Jack sense?
- one or two Mic volume controls?
- CD/Line-in: presense in the mixer
Signed-off-by: Andy Shevchenko <andy@smile.org.ua>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the support of new Realtek codecs:
1. New ALC889 Support
2. New ALC267 Support
3. New ALC269 Support
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds support for VIA new HD audio codec, VT1708B.
Signed-off-by: Josepch Chan <josephchan@via.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the model targa-2ch-dig for MSL L745 (ALSA bug#3641).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The attached patch should fix typo in auto initialization verbs for ALC883
codec.
Signed-off-by: Andy Shevchenko <andy@smile.org.ua>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Volume knob controls with STAC codecs seem to cause problems with some
devices. Volumes change very slowly or silent suddenly. It's likely
due to conflict between the software and the hardware volume knob
setup.
Since we'll have a virtual master control in future, it's safer to
remove this control completely right now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Show more attributs of volume-knob widgets.
Also don't put empty lines when no connection list is found.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
not sleeping for every codec read/write but doing a short udelay and
a conditional reschedule has cut suspend+resume latency by about 1
second on my T60.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch is to add R6xx HDMI audio support. Meanwhile, the device ID
in the previous patch is changed.
I have checked the patch from Herton Ronaldo Krzesinski, it's right as
our spec said. :)
Signed-off-by: Wolke Liu <Wolke.Liu@amd.com>
Signed-off-by: Andrea Zhang <Andrea.Zhang@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Check the value ranges in ctl put callbacks properly so that
invalid values won't be stored or written to registers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the missing model string for the new support of HP TC T5735.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the support of HP Thin Client T5735 [0x103c 0x302f] with ALC262 codec.
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
When a mic jack is set up as the multiple I/O, it may issue the automute
function wrongly. This patch fixes the wrong automute detection.
Signed-off-by: Jiang Zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Dell laptops have multiple HP jacks that can be used for multi-channel
outputs. The current auto pincfg handles the speaker as the primary
output and thus cannot handle the multi-channel configuration for such
cases. This patch adds a workaround to fix this issue by swapping the
HP and speaker during multi-channel setup routines.
Signed-off-by: Jiang Zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Updated dell-m82 model pin config table. The old config doesn't work
with Dell 1210 and co.
Signed-off-by: Jiang Zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added more laptops subsystem id's that have STAC9228 DMIC support.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added analog loopback support and missing ADC capture mixer for the
STAC92HD71 codec family.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added initial support for the STAC92HD71BXX family of codecs.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The Audio interface on HD2400/HD2600 cards isn't currently detected by
snd-hda-intel. I added missing pci device ids for RV610 and RV630, but
I only had a HD2400 pro card to test, where now the audio interface is
detected (and no need to change patch_atihdmi.c, as the codec vendor id
remains 0x1002aa01 for which we already have an entry there). I also
couldn't test if sound pass-trough is ok (and I don't know how to), but
at least now the device is detected.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added support for the dmics and enabled EAPD for several laptops with
STAC9228 cards.
Signed-off-by: Matthew Ranostay <mranostay@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Simple patch to add the Asus VX1 laptop to the Analog Devices pci quirk list.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Some small improvements on autocfg stuff:
- sort HP pins by sequence number, too
- move sole mic pin to AUTO_PIN_MIC instead of AUTO_PIN_FRONT_MIC
- ditto for line-in pin
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Show the current EAPD status and volume-knob status in proc file.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds full record and playback support for the Samsung Q1
Ultra - Vista model (different codec than the earlier Q1 Ultra models).
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Changed the dmux for STAC9228 from ADC1MUX to ADC0MUX to avoid confusion.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added a dmux to the STAC9228 cards with DMIC support. And added a
STAC_DIGITAL_INPUT_SOURCE macro for repeating mixer code.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the missing STAC9228 DMIC support.
Also added a new vendor id tag for IDT.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the missing model string 'eeepc-p701' for ALC662 codec.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This reverts commit 57a04513cb.
Harald Dunkel reports that it broke sound for him:
"Alsa stopped working for me. I still can access /dev/dsp, change the
volume and so on, but the speakers are quiet."
Reverting it fixed things for him.
Reported-and-tested-by: Harald Dunkel <harald.dunkel@t-online.de>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
not sleeping for every codec read/write but doing a short udelay and
a conditional reschedule has cut suspend+resume latency by about 1
second on my T60.
The patch also fixes the unexpected codec-connection errors that
happen more often in the new power-save mode:
http://lkml.org/lkml/2007/11/8/255http://bugzilla.kernel.org/show_bug.cgi?id=9332
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Volume knob controls with STAC codecs seem to cause problems with some
devices. Volumes change very slowly or silent suddenly. It's likely
due to conflict between the software and the hardware volume knob
setup.
Since we'll have a virtual master control in future, it's safer to
remove this control completely right now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The recent addition of checking PINCAP for EAPD seems to break some
systems due to unexpected response from the codec chip. We shouldn't
issue GET_PINCAP verb to non-PIN widgets. Now checks the widget type
before checking EAPD bit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
AD1986A has a hardware problem that it cannot share a stream with
multiple pins properly. The problem occurs e.g. when a volume is changed
during playback.
So far, hda-intel driver unconditionally assigns the stream to multiple
output pins in copy-front mode, and this should be avoided for AD1986A
codec.
The original fix patch was by zhejiang <zhe.jiang@intel.com>.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
dac_nids arrays in each codec support code may have up to 5 items
when assigned from the auto-configurator. Some codec codes have
less numbers than the possible max. This patch defines the constant
and fixes the array definitions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fixed the build error from patch_sigmatel.c when built without
CONFIG_SND_HDA_GENERIC by defining a dummy function to return error.
Also, clean up hda_codec.c by removing unneeded ifdefs (the compiler
will optimize out).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fixed the init verbs and added the missing volume controls so that
the driver works again with Conexant 5045 codec chip.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The addition of volume knob as Master volume resulted in conflict with
the existing one by stac92xx_auto_create_hp_ctls().
This patch fixes the conflict, and still keeps the Master control for
codecs without volume knob as much as possible.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The jack detection bit on AD1986A Lenovo N100 seems inverse from
the standard definition. Now fixed the detection properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fixed SKU ID function for realtek codecs. It's used by the automatic
BIOS configuration mode. Now it supports the correct jack-detection
mechanism, too.
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Reported by Jan-Marek Glogowski.
The dmic array is passed to snd_hda_parse_pin_def_config() and
should be zero-terminated.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Reported by zhejiang <zhe.jiang@intel.com>
'I found that STAC_VOLKNOB hardwired the KNOB nid to 0x24.
It is okay for stac9205 and stac927x.
But the VolumeKnob nid of stac9220-9221 is 0x16.'
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fixed ALC262 fujitsu model to support Fujitsu Lifebook C1410 properly.
It requires EAPD and has separate int/ext mic inputs (which was missing
in the current driver).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
My bad, I forgot to update the num_items field when added a new item
to vaio_mux items table, so the last item 'PCM' disappeared.
Now it has the right number 3.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fix the output of Gateway laptops with STAC9200 codec chip.
They require the EAPD control for some pins. These pins shouldn't be
powered down.
To enable EAPD control, a new model 'gateway' was added to STAC9200.
The known PCI SSIDs are included in the quirk list.
The fix was originally suggested by Brian Hinz, in ALSA bug#2948.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added zero checks in input-mux helper functions to avoid Oops.
Some devices may have no input pins while the driver registers
control elements calling these functions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Add the MCP79 support to hda driver.
The patch base on kernel 2.6.23-rc7
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added the missing support for ASUS A7J [0x1043 0x1243]
Signed-off-by: Kailang Yang <kailang@realtek.com.tw>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fix schedule_timeout() use in alsa-kernel. Mostly just
schedule_timeout(1) --> schedule_timeout_uninterruptible(1)
The wavefront_synth one fixes the surrounding loop as well. In ymfpci_main,
delete a superfluous set_current_state() and in soc/soc-dapm.c replace an
_interruptible with _uninterruptible in some debug code; it's not waiting
for signals.
Signed-off-by: Rene Herman <rene.herman>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
More laptop BIOS changes the subsystem id for STAC9205 cards if the
microphone is toggled on/off in the settings.
The patch removes the old STAC_9205_M43xx and use STAC_9205_DELL_M43.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added CONFIG_SND_AC97_POWER_SAVE_DEFAULT and CONFIG_SND_HDA_POWER_SAVE_DEFAULT
Kconfig options as the default values for power-saving mode of AC97 and
HD-audio drivers, respectively.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Intel HD Audio: Use list_for_each_entry(_safe) instead of
list_for_each(_safe)
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds support for the Asus M2A-VM HDMI and Abit IP35-PRO
motherboards.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
I had a request for a 4 channel mode. This should implement front
and surround outputs, leaving the 3rd plug for mic input.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
When modem is disabled in the BIOS, detection of the number of codecs
always fails after booting if STATESTS is not cleared first.
This patch fixes this problem and also adds an error check in a place
where a read error would lead to a very large number of pointless loops.
Signed-off-by: Danny Tholen <obiwan@mailmij.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Some laptop BIOS change the subsystem id for STAC9205 cards if the
microphone isn't toggled on/off in the settings.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added the proper model=toshiba for Toshiba A305 with ALC268 codec.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Mic Boost mixer volume was missing in some ALC882 models. Added now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
