Improve SFF HSM violation reporting such that each HSM violation can
be distinguished using ehi_desc.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some AHCI controllers (ICH7 was reported) set pending bit in
HOST_IRQ_STAT for non-existent ports and when it's not cleared falls
into IRQ storm. Always clear full irq_stat instead of only the bits
that are handled. As nothing changes for recognized ports, the risk
of breaking things is pretty low.
Reported and verified by Philipp Thomas in the following suse
bugzilla.
https://bugzilla.novell.com/attachment.cgi?id=215692
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Philipp Thomas <pth@novell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There's another DID used for Adaptec card. Add it.
Reported by Travis Read.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Travis Read <ics@dark.net.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This adds blk_queue_update_dma_pad to prevent LLDs from overwriting
the dma pad mask wrongly (we added blk_queue_update_dma_alignment due
to the same reason).
This also converts libata to use blk_queue_update_dma_pad instead of
blk_queue_dma_pad.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
sata_uli can't do hardresets reliably and lock up. This went
unnoticed till now as softreset was the default and hardreset was only
used after softreset failed.
Reported by Christian Casteyde in bz#10860.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Christian Casteyde <casteyde.christian@free.fr>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
BAST: Remove old IDE driver
pcmcia ide kingston compactflash's have a new manufacturer id
pcmcia: add another pata/ide ID
pcmcia: add an pata/ide ID
ide: increase timeout in wait_drive_not_busy()
palm_bk3710: fix resource management
Addition of Transcend 1GB 45x id so that it is properly detected.
[bart: fix typo in ide-cs's ID spotted by Alan Cox]
Signed-off-by: William Peters <w1ll14@gmail.com>
Signed-off-by: Kristoffer Ericson <Kristoffer_e1@hotmail.com>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
From: Piter PUNK <piterpunk@slackware.com>
SiS AHCIs say they can do PMP but can't and fail detection if SRST w/
pmp==15 is used. Turn off PMP support.
tj: added patch description, adapted patch to #upstream-fixes and
renamed board_ahci_sis to board_ahci_nopmp.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
TOSHIBA also used "TECRA M4" in additon to "Tecra M4", add it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add HAVE_PATA_PLATFORM to select the pata platform driver
to ensure that we do not end up with a long 'depends on' list
when other users of this driver turn up.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Chip errata sometimes prevents reliable use of PIO commands which involve
more than a single DRQ (data request). In normal operation, libata should
not generate such PIO commands (uses DMA instead), but they could be sent
in via SG_IO from userspace.
A full workaround might be to break up such commands into sequences
of single DRQ ones, but that's just way too complex for something
that doesn't normally happen in real life.
So, allow the attempt (it often works, despite the errata),
but log the event for reference when somebody screams.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The early chipsets cannot safely handle Async Notification (AN),
but 6041/6081 chip revision "C0" (and newer) can handle it.
So allow AN for "C0" and higher.
This enables use of hotplug on PMP ports for the 6041/6081 PCI Rev.9 chips.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There's no reason to check whether to use DMA or not for no data
commands. Don't do it. While at it, make local variable using_pio in
atapi_xlat() set iff ATAPI_PROT_PIO is going to be used and rename
ata_check_atapi_dma() to atapi_check_dma() for consistency.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
JMB361 has only one port but reports it has two causing longish probe
failure on the second one. Quirk it.
Reported by Gajo Petrovic in bz 10911.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Gajo Petrovic <gajo01@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There is one bug in ATI SATA PMP of SB600 and SB700 old revision, which leads
to soft reset failure. This patch can fix the bug.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MCP65 ahci can do NCQ but doesn't set the CAP bit and rev A0 and A1
can't do MSI but have MSI capability. Implement AHCI_HFLAG_YES_NCQ
and apply appropriate workarounds.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix G5 SATA irq 18: nobody cared, reported on -rc5 by Olaf Hering:
fixlet to a57c1bade5 libata-sff:
Fix oops reported in kerneloops.org for pnp devices with no ctl
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Tested-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Make ata_sff_altstatus private so nobody uses it by mistake
- Drop the 400nS delay from it
Add
ata_sff_irq_status - encapsulates the IRQ check logic
This function keeps the existing behaviour for altstatus using devices. I
actually suspect the logic was wrong before the changes but -rc isn't the
time to play with that
ata_sff_sync - ensure writes hit the device
Really we want an io* operation for 'is posted' eg ioisposted(ioaddr) so
that we can fix the nasty delay this causes on most systems.
- ata_sff_pause - 400nS delay
Ensure the command hit the device and delay 400nS
- ata_sff_dma_pause
Ensure the I/O hit the device and enforce an HDMA1:0 transition delay.
Requires altstatus register exists, BUG if not so we don't risk
corruption in MWDMA modes. (UDMA the checksum will save your backside in
theory)
The only other complication then is devices with their own handlers.
rb532 can use dma_pause but scc needs to access its own altstatus
register for internal errata workarounds so directly call the drivers own
altstatus function.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The handling for PHY_MODE4 was originally just cloned from the
Marvell proprietary driver (with their blessing).
But we can do better than that.
Tidy things up with some judicious mask definitions, to improve maintainability.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add ICH6 on ACER Aspire 1694WLMi to list of laptops that use short cables
rather than 80 wire
OriginalAuthor: Tiago Sousa
OriginalLocation: http://launchpadlibrarian.net/11627664/new.ich_laptop.short.cables.diff
Bug: #187121
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: maximilian attems <max@stro.at>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* Differentiate between bay devices in dock stations and others:
- When an ACPI_NOTIFY_EJECT_REQUEST appears, just signal uevent to
userspace (that is when the optional eject button on a bay device is
pressed/pulled) giving the possibility to unmount file systems and to
clean up. Also, only send uevent in case we get an EJECT_REQUEST
without doing anything else. In other cases, you'll get an add/remove
event because libata attaches/detaches the device.
- In case of a dock event, which in turn signals an
ACPI_NOTIFY_EJECT_REQUEST, immediately detach the device, because it
may already have been gone
* In case of an ACPI_NOTIFY_DEVICE/BUS_CHECK, evaluate _STA to check if
the device has been plugged or unplugged. If plugged, hotplug it, if
unplugged, just signal event to userspace
(initial patch by Matthew Garrett <mjg59@srcf.ucam.org>)
* Call ACPI _EJ0 for detached devices
Signed-off-by: Holger Macht <hmacht@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Change the partial Device IDs of nvidia MCP7B AHCI controller in ahci.c,
as the actual PCI IDs deployed in the field differed from the forecasted ones
preemptively placed in the driver.
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The following commit (4c9bf4e799):
libata: replace tf_read with qc_fill_rtf for non-SFF drivers
Broke the sata_fsl.c driver in 2.6.26-rc. I know the following patch fixes
the issue, it clearly also adds port multipler support. The current
2.6.26-rc driver is broken.
On boot with debug enabled we get something like (w/o this patch):
spurious interrupt!!, CC = 0x1
interrupt status 0x1
xx_scr_read, reg_in = 1
spurious interrupt!!, CC = 0x1
interrupt status 0x1
xx_scr_read, reg_in = 1
spurious interrupt!!, CC = 0x1
interrupt status 0x1
xx_scr_read, reg_in = 1
.. continues for ever.
This change fixes this as a side effect of adding port multiplier support.
Signed-off-by: Ashish Kalra <ashish.kalra@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
As in sil4726, SRST can't be trusted on sil3726 causing detection
problems under certain configuraitons. I thought it was from the
Config Disk device but apparently not.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix libata-scsi kernel-doc notation:
Warning(linux-2.6.25-git15//drivers/ata/libata-scsi.c:1659): No description found for parameter 'cmd'
Warning(linux-2.6.25-git15//drivers/ata/libata-scsi.c:1971): No description found for parameter 'buf'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ICH8M on macbooks are peculiar in that some of them lock up when the
second port is enabled, some return bogus values on SIDPR access while
yet others hang on SIDPR access. Also, the ich8m_apple_sata entry was
wrongly added below generic ich8m entry making it virtually useless.
This patch works around macbook ich8m problems by
* moving ich8m_apple_sata entry above generic ich8m entry
* dropping PIIX_FLAG_SIDPR from ich8m_apple_sata
* adding subsystem 106b:00a1 as ich8m_apple_sata
Reported and tested by MATSUBAYASHI.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: MATSUBAYASHI 'Shaolin' Kohji <shaolin@rhythmaning.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The 5182 System-On-Chip (SOC) variant wants certain lower
bits to be cleared on any write to the PHY_MODE3 register.
If/when support is added for other SOC variants, we'll need
some way to uniquely identify the 5182, and not perform this
workaround for the others.
But for now, it is the only SOC variant we support here.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The "B2" variant of the 6041/6081 (genII) chips requires
that the PHY_MODE3 register be rewritten after any write
to PHY_MODE4.
This fixes a regression introduced by an earlier patch.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The only public release of the 6042/7042 chips was/is revision "B0".
Remove code that attempted to deal with earlier, non-released revs.
This matches the logic of the current Marvell "proprietary" driver.
Also, bump up the sata_mv version number, to reflect this batch of erratas.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix and update the errata handling for the PHY_MODEx registers.
This improves receiver noise tolerance, among other things.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Convert the System-on-Chip flag from a host flag to an hpriv flag,
for better consistency with other chip-rev flags, and for easier use
in errata fixes etc.
Also change the related "HAS_PCI()" into "!IS_SOC()" for better consistency
of naming/use (everything else SOC-related already uses "SOC").
There are no functionality changes in this patch.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The libata-acpi.c code currently accepts hotplug messages from both the
port and the device. This does not match the behaviour of the bay
driver, and may result in confusion when two hotplug requests are
received for the same device. This patch limits the hotplug notification
to removable ACPI devices, which in turn allows it to use the _STA
method to determine whether the device has been removed or inserted.
On removal, devices are marked as detached. On insertion, a hotplug scan
is started. This should avoid lockups caused by the ata layer attempting
to scan devices which have been removed. The uevent sending is moved
outside the spinlock in order to avoid a warning generated by it firing
when interrupts are disabled.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I was hoping ATA_HORKAGE_NODMA | ATA_HORKAGE_SKIP_PM could keep it
happy but no even this doesn't work under certain configurations and
it's not like we can do anything useful with the cofig device anyway.
Replace ATA_HORKAGE_SKIP_PM with ATA_HORKAGE_DISABLE and use it for
the config device. This makes the device completely ignored by
libata.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When 4140 PMP is attached to sil24, NCQ commands to fan out port 1 and
2 (0 based) often stall if commands are in progress to other ports.
I've tried a number of things but can't tell what's going on. It
never happens w/ ahci and reportedly sata_mv which can issue NCQ
commands to multiple devices simultaneously like sil24 does.
Disable NCQ for devices behind 4140 PMP for the time being.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There's no reason to schedule LPM action after probing is complete
causing another EH iteration. Just schedule it together with probing
itself.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
PMP notification during reset can make some controllers fail reset
processing and needs to be turned off during resets. PMP attach and
full-revalidation path did this via sata_pmp_configure() but the quick
revalidation wasn't. Move the notification disable code right above
fan-out port recovery so that it's always turned off.
This fixes obscure reset failures.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This timeout was set low because previously PMP register access was
done via polling and register access timeouts could stack up. This is
no longer the case. One timeout will make all following accesses fail
immediately.
In rare cases both marvell and SIMG PMPs need almost a second. Bump
it to 3s.
While at it, rename it to SATA_PMP_RW_TIMEOUT. It's not specific to
SCR access.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
No reason to get overzealous about recovered comm and data errors.
Some PHYs habitually sets them w/o no good reason and being draconian
about these soft error conditions doesn't seem to help anybody.
If need ever rises, we might need to add soft PHY error condition, say
AC_ERR_MAYBE_ATA_BUS and use it only to determine whether speed down
is necessary but I don't think that's very likely to happen. It's far
more likely we'll get timeouts or fatal transmission errors if
recovered errors are so prominent that they hamper operation.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Originally, whole reset processing was done while the port is frozen
and SError was cleared during @postreset(). This had two race
conditions. 1: hotplug could occur after reset but before SError is
cleared and libata won't know about it. 2: hotplug could occur after
all the reset is complete but before the port is thawed. As all
events are cleared on thaw, the hotplug event would be lost.
Commit ac371987a8 kills the first race
by clearing SError during link resume but before link onlineness test.
However, this doesn't fix race #2 and in some cases clearing SError
after SRST is a good idea.
This patch solves this problem by cross checking link onlineness with
classification result after SError is cleared and port is thawed.
Reset is retried if link is online but all devices attached to the
link are unknown. As all devices will be revalidated, this one-way
check is enough to ensure that all devices are detected and
revalidated reliably.
This, luckily, also fixes the cases where host controller returns
bogus status while harddrive is spinning up after hotplug making
classification run before the device sends the first FIS and thus
causes misdetection.
Low level drivers can bypass the logic by setting class explicitly to
ATA_DEV_NONE if ever necessary (currently none requires this).
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Previously reset freeze/thaw handling lived outside of ata_eh_reset()
mainly because the original PMP reset code needed the port frozen
while resetting all the fan-out ports, which is no longer the case.
This patch moves freeze/thaw handling into ata_eh_reset().
@prereset() and @postreset() are now called w/o freezing the port
although @prereset() an be called frozen if the port is frozen prior
to entering ata_eh_reset().
This makes code simpler and will help removing hotplug event related
races.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Reorganize ata_eh_reset() such that @prereset() is called even when no
reset method is available and if block is used instead of goto to skip
actual reset. This makes no reset case behave better (readiness wait)
and future changes easier.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The @online out parameter is supposed to set to true iff link is
online and reset succeeded as advertised in the function description
and callers are coded expecting that. However, sata_link_reset()
didn't behave this way on device readiness test failure. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Minor coding-style fixes for sata_promise:
- remove stray blank lines
- fix checkpatch.pl errors; warnings about long lines
remain, but I don't intend to address those at this time
- remove two inline directives: neither is essential and
both functions are trivially inlinable anyway by virtue
of being static and having a single unique call site
- fix comment in pdc_interrupt(): the bits in PDC_INT_SEQMASK
denote SEQIDs not tags, the distinction becomes important
when NCQ gets implemented
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch cleans up sata_promise's mmio accesses.
In sata_promise there are three distinct mmio address spaces:
1. global registers, offsets from host->iomap[PDC_MMIO_BAR]
2. per-port ATA registers, offsets from ap->ioaddr.cmd_addr
3. per-port SATA registers, offsets from ap->ioaddr.scr_addr
The driver currently often fails to indicate which address space
a given mmio base pointer refers to, which is a source of bugs
and confusion (see recent pdc_thaw() irq clearing bug; it's also
been an obstacle for the pending NCQ extensions).
To reduce these problems, adopt a coding style where the name of
a base pointer always indicates which address space it refers to:
1. global registers: host_mmio
2. per-port ATA registers: ata_mmio
3. per-port SATA registers: sata_mmio
Also rearrange register offset definitions to clearly indicate
which address space they belong to, and add a symbolic definition
for the previously hard-coded PHYMODE4 register.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch fixes two bugs in sata_promise's irq status clearing paths:
1. When clearing the irq status for a specific port, the driver
read the global SEQMASK register. This is wrong because that
clears the irq status for _all_ ports.
2. pdc_thaw() incorrectly added the PDC_INT_SEQMASK host register
offset to a per-port ata engine base address. This resulted in
it reading the unrelated PDC_PKT_SUBMIT register, which did not
have the desired irq status clearing effect.
In both cases the fix is to read from the port's Command/Status
register. This also matches what Promise's own driver does.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use the kernel-provided clamp_val() macro.
FIT was always applied to a member of struct ata_timing (unsigned short)
and two constants. clamp_val will not cast to short anymore.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Check for an empty request queue before stopping EDMA after a FBS-NCQ error,
as per recommendation from the Marvell datasheet.
This ensures that the EDMA won't suddenly become active again
just after our subsequent check of the empty/idle bits.
Also bump DRV_VERSION.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Part five of simplifying/fixing handling of the main_irq_mask register
to resolve unexpected interrupt issues observed in 2.6.26-rc*.
Keep a cached copy of the main_irq_mask so that we don't have
to stall the CPU to read it on every pass through mv_interrupt.
This significantly speeds up interrupt handling, both for sata_mv,
and for any other driver/device sharing the same PCI IRQ line.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Part four of simplifying/fixing handling of the main_irq_mask register
to resolve unexpected interrupt issues observed in 2.6.26-rc*.
Ignore masked IRQs in mv_interrupt().
This prevents "unexpected device interrupt while idle" messages.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Part three of simplifying/fixing handling of the main_irq_mask register
to resolve unexpected interrupt issues observed in 2.6.26-rc*.
Partially fix a reported bug whereby we sometimes miss seeing drives on
a port-multiplier, as reported by Gwendal Grignou <gwendal@google.com>.
The problem was that we were receiving unexpected interrupts
during EH from POLLed commands while accessing port-multiplier registers.
These unexpected interrupts can be prevented by masking the DONE_IRQ bit
for the port whenever not operating in EDMA mode.
Also fix port_stop() to mask all port interrupts.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Part two of simplifying/fixing handling of the main_irq_mask register
to resolve unexpected interrupt issues observed in 2.6.26-rc*.
Consolidate all updates of the host main_irq_mask register
into a single function. This simplifies maintenance,
and also prepares the way for caching it (later).
No functionality changes in this update.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Part one of simplifying/fixing handling of the main_irq_mask register
to resolve unexpected interrupt issues observed in 2.6.26-rc*.
Don't blindly enable port IRQs at host init time.
Instead, enable only the bits that we want,
which in this case is simply the PCI_ERR bit.
The per-port bits can wait until the ports are reset/probed for devices.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that we handle the FIS_IRQ_CAUSE register correctly,
we can also now handle SATA asynchronous notification events.
So enable them, but only for the more modern GenIIe chips.
(older chips have unaddressed errata issues related to this).
This fixes hot plug/unplug for port-muliplier ports.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Group all of the flags for GenIIe devices into a common definition,
to ensure that any updates to them are shared by all GenIIe devices.
This will help make future maintenance somewhat simpler.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix handling of the FIS_IRQ_CAUSE register in sata_mv.
This register exists *only* on GenIIe devices, so don't bother
writing to it on older chips. Also, it has to be read/cleared
in mv_err_intr() before clearing the main ERR_IRQ_CAUSE register.
This keeps sata_mv from getting stuck forever on certain error types.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Always request a softreset after hardreset succeeds.
This fixes a regression reported by Martin Michlmayr <tbm@cyrius.com>.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Set ATAPI host state machine to control IDE device terminate sequence.
Some IDE harddisk may assert terminate sequence in the middle of a
formal DMA transaction and resume later. Bit DETECT_TERM in ATAPI_CTRL
register determines whether the ATAPI host state machine or the kernel
driver should take care of this case.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
A couple of distributions (Fedora, Ubuntu) were having weird problems with the
ATI IXP series PATA controllers being reported as simplex. At the heart of
the problem is that both distros ignored the recommendations to load pata_acpi
and ata_generic *AFTER* specific host drivers.
The underlying cause however is that if you D3 and then D0 an ATI IXP it
helpfully throws away some configuration and won't let you rewrite it.
Add checks to ata_generic and pata_acpi to pin ATIIXP devices. Possibly the
real answer here is to quirk them and pin them, but right now we can't do that
before they've been pcim_enable()'d by a driver.
I'm indebted to David Gero for this. His bug report not only reported the
problem but identified the cause correctly and he had tested the right values
to prove what was going on
[If you backport this for 2.6.24 you will need to pull in the 2.6.25
removal of the bogus WARN_ON() in pcim_enagle]
Signed-off-by: Alan Cox <alan@redhat.com>
Tested-by: David Gero <davidg@havidave.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_inic162x is now ready for production use. Bump the version,
explain what's working and what's not and drop EXPERIMENTAL.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When attached to cardbus, mmio region is at BAR 1. Other than that,
everything else is the same. Add support for it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_inic162x now doesn't use any SFF features. Remove all SFF
related stuff.
* Mask unsolicited ATA interrupts. This removes our primary source of
spurious interrupts and spurious interrupt handling can be tightened
up. There's no need to clear ATA interrupts by reading status
register either.
* Don't dance with IDMA_CTL_ATA_NIEN and simplify accesses to
IDMA_CTL.
* Inherit from sata_port_ops instead of ata_sff_port_ops.
* Don't initialize or use ioaddr. There's no need to map BAR0-4
anymore.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use IDMA for ATAPI commands. Write and some misc commands time out
when executed using ATAPI_PROT_DMA but ATAPI_PROT_PIO works fine. As
PIO is driven by DMA too, it doesn't make any noticeable difference
for native SATA devices. inic_check_atapi_dma() is implemented to
force PIO for those ATAPI commands.
After this change, sata_inic162x issues all commands using IDMA.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use IDMA for PIO and non-data commands. This allows sata_inic162x to
safely drive LBA48 devices. Kill inic_dev_config() which contains
code to reject LBA48 devices.
With this change, status checking in inic_qc_issue() to avoid hard
lock up after hotplug can go away too.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The modified driver on initio site has enough clue on how to use IDMA.
Use IDMA for ATA_PROT_DMA.
* LBA48 now works as long as it uses DMA (LBA48 devices still aren't
allowed as it can destroy data if PIO is used for any reason).
* No need to mask IRQs for read DMAs as IDMA_DONE is properly raised
after transfer to memory is actually completed. There will be some
spurious interrupts but host_intr will handle it correctly and
manipulating port IRQ mask interacts badly with the other port for
some reason, so command type dependent port IRQ masking is not used
anymore.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
inic162x can't reliably read back TF or at least we don't know how to
do it yet. The only values which seem reliable are status and error.
This patch updates access to TF.
* implement inic_tf_read() which reads the TF area in mmio area
* implement custom inic_qc_fill_rtf() which only returns true if
status indicates device error. it'll be returning bogus addresses
for device errors but it'll be able to report why it failed at
least.
* implement custom inic_check_ready() and use ata_wait_after_reset()
instead of the SFF version.
* use inic_tf_read() for classification.
This is not perfect but it fixes hotplug detection failure and at
least makes the driver report 0's instead of random garbages while
reporting valid status and error for device errors.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* add a bunch of constants, most are from the datasheet, a few
undocumented ones are from initio's modified driver
* HCTL_PWRDWN is bit 12 not 13
This is in preparation of further inic162x updates.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* use larger indents for structure member definitions
* kill unused variable @addr in inic_scr_write()
* kill unnecessary flushes in inic_freeze/thaw()
* kill buggy explicit kfree() on devres managed port private data
This is in preparation of further inic162x updates.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some tidying as suggested by Grant Grundler.
Nuke local bit-counting function from sata_mv in favour of using hweight16().
Also add a short explanation for the 15msec timeout used when waiting for empty/idle.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Convert sata_mv's EH for FIS-based switching (FBS) over to the
sequence recommended by Marvell. This enables us to catch/analyze
multiple failed links on a port-multiplier when using NCQ.
To do this, we clear the ERR_DEV bit in the EDMA Halt-Conditions register,
so that the EDMA engine doesn't self-disable on the first NCQ error.
Our EH code sets the MV_PP_FLAG_DELAYED_EH flag to prevent new commands
being queued while we await completion of all outstanding NCQ commands
on all links of the failed PM.
The SATA Test Control register tells us which links have failed,
so we must only wait for any other active links to finish up
before we stop the EDMA and run the .error_handler afterward.
The patch also includes skeleton code for handling of non-NCQ FBS operation.
This is more for documentation purposes right now, as that mode is not yet
enabled in sata_mv.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Introduce a new "delayed error handling" mechanism in sata_mv,
to enable us to eventually deal with multiple simultaneous NCQ
failures on a single host link when a PM is present.
This involves a port flag (MV_PP_FLAG_DELAYED_EH) to prevent new
commands being queued, and a pmp bitmap to indicate which pmp links
had NCQ errors.
The new mv_pmp_error_handler() uses those values to invoke
ata_eh_analyze_ncq_error() on each failed link, prior to freezing
the port and passing control to sata_pmp_error_handler().
This is based upon a strategy suggested by Tejun.
For now, we just implement the delayed mechanism.
The next patch in this series will add the multiple-NCQ EH code
to take advantage of it.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Export ata_eh_analyze_ncq_error() for subsequent use by sata_mv,
as suggested by Tejun.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Separate out the inner loop body of mv_host_intr()
into it's own function called mv_port_intr().
This should help maintainabilty.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove the unwanted reads of hc_irq_cause from mv_host_intr(),
thereby removing a bug whereby we were not always reading it when needed..
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Sigh. Undo some earlier changes to mv_port_intr(),
so that we now read/clear SError again in all cases.
Arrange the top of the function to be as close as possible
to what we need for a later update (in this series) for ERR_DEV handling.
Fix things so that libata-eh can attempt a READ_LOG_EXT_10H
in response to a failed NCQ command, by just doing a local
mv_eh_freeze() rather than ata_port_freeze().
This will now fully handle NCQ errors much of the time,
but more fixes are needed for FBS/PMP, and for certain chip errata.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rearrange mv_config_fbs() to more closely follow the (corrected) datasheet
recommendations for NCQ and FIS-based switching (FBS).
Also, maintain a port flag to let us know when FBS is enabled.
We will make more use of that flag later in this patch series.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Part 1 of workaround for errata "sata#25" for the 60x1 series
(the second half of this errata workaround is still in development.
Bit22 of the GPIO port has to be set "on" when in NCQ mode.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The EDMA engine cannot tolerate a mix of NCQ/non-NCQ commands,
and cannot be used for PIO at all. So we need to prevent libata
from trying to feed us such mixtures.
Introduce mv_qc_defer() for this purpose, and use it for all chip versions.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When performing EH, it is recommended to wait for the EDMA engine
to empty out requests-in-progress before disabling EDMA.
Introduce code to poll the EDMA_STATUS register for idle/empty bits
before disabling EDMA. For non-EH operation, this will normally exit
without delay, other than the register read.
A later series of patches may focus on eliminating this and various
other register reads (when possible) throughout the driver,
but for now we're focussing on solid reliablity.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some of the GenIIe EDMA optimizations should not be used
for non-PCI (SOC) devices, and nor for certain configurations
of conventional PCI (non PCI-X, PCIe) buses.
Logic taken/simplified from that in the Marvell proprietary driver.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
More cosmetic changes; no code changes.
-- try and improve consistency of naming.
-- add missing _OFS to tails of register offset definitions.
-- rename mv_setup_ifctl() to mv_setup_ifcfg(), since that's what it really does.
-- remove/move some dead comments
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On certain configurations (certain macbooks), even though all the
conditions for SIDPR access described in the datasheet are met,
actually reading those registers just returns 0 and have no effect on
write. Verify SIDPR is actually working before enabling it.
This is reported by Ryan Roth in bz#10512.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Ryan Roth <ryan.roth@ch2m.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some controllers (jmb and inic162x) use 0x77 and 0x7f to indicate that
the device isn't ready yet. It looks like they use 0xff if device
presence is detected but connection isn't established. 0x77 or 0x7f
after connection is established and use the value from signature FIS
after receiving it.
This patch implements ata_check_ready(), which takes TF status value
and determines whether the port is ready or not considering the above
and other conditions, and use it in @check_ready() functions. This is
safe as both 0x77 and 0x7f aren't valid ready status value even though
they have BSY bit cleared.
This fixes hot plug detection failures which can be triggered with
certain drives if they aren't already spun up when the data connector
is hot plugged.
Tested on sil, sil24, ahci (jmb/ich), piix and inic162x combined with
eight drives from all major vendors.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The discrete VIA ATA chips don't have 0x40 enable bits. We check that
properly in one location but not another. This causes some users 6410
RAID cards to be incorrectly skipped.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use correct variable, achieve desired result...
Spotted by LKML/linux-ide poster whose name I lost (apologies!)
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tidy up naming of things associated with the PCI / SOC chip
"main irq cause/mask" registers, as inspired by Jeff.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Buffer length handling in simulated commands is error-prone and full
of bugs. There are a number of places where necessary length checks
are missing and if the output buffer is passed in as sglist, nothing
works.
This patch adds a static buffer ata_scsi_rbuf which is sufficiently
large to handle the larges output from simulated commands (4k
currently), let all simulte functions write to the buffer and removes
all length checks as we know that there always is enough buffer space.
Copying in (for ATAPI inquiry fix up) and out are handled by
sg_copy_to/from_buffer() behind ata_scsi_rbuf_get/put() interface
which handles sglist properly.
This patch is inspired from buffer length check fix patch from Petr
Vandrovec.
Updated to use sg_copy_to/from_buffer() as suggested by FUJITA
Tomonori.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Petr Vandrovec <petr@vmware.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* make ata_scsiop_*() static
* make ata_scsi_set_sense() static and move it above its users
* make ata_scsi_rbuf_fill() static
* kill unused ata_scsi_badcmd()
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The platform is actually named routerboard 532 so let's call it this. This
patch only rename files, Kconfig and C symbols; no functional changes.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When count reaches 0 the postfix decrement still subtracts (to -1),
so bfin_reset_controller() returns as if the busy flag was cleared
while it was not.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Re-enable hotplug, now that the interrupt/error handling are mostly sane.
Also update the TODO list at the top.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
