CIFS in some heavy stress conditions cifs could get EAGAIN
repeatedly in smb_send2 which led to repeated retries and eventually
failure of large writes which could lead to data corruption.
There are three changes that were suggested by various network
developers:
1) convert cifs from non-blocking to blocking tcp sendmsg
(we left in the retry on failure)
2) change cifs to not set sendbuf and rcvbuf size for the socket
(let tcp autotune the buffer sizes since that works much better
in the TCP stack now)
3) if we have a partial frame sent in smb_send2, mark the tcp
session as invalid (close the socket and reconnect) so we do
not corrupt the remaining part of the SMB with the beginning
of the next SMB.
This does not appear to hurt performance measurably and has
been run in various scenarios, but it definately removes
a corruption that we were seeing in some high stress
test cases.
Acked-by: Shirish Pargaonkar <shirishp@us.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
The most important property we need from nfs_attr_generation_counter is
monotonicity, which is not guaranteed by the current system of smp memory
barriers. We should convert it to an atomic_long_t, and drop the memory
barriers.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
As reported by Eric Paris, the capable() check in ext4_has_free_blocks()
sometimes causes SELinux denials.
We can rearrange the logic so that we only try to use the root-reserved
blocks when necessary, and even then we can move the capable() test
to last, to avoid the check most of the time.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Mingming pointed out that ext4_claim_free_blocks & ext4_has_free_blocks
are largely cut & pasted; they can be collapsed/merged as follows.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The transaction can potentially get dropped if there are no buffers
that need to be written. Make sure we call the commit callback before
potentially deciding to drop the transaction. Also avoid
dereferencing the commit_transaction pointer in the marker for the
same reason.
This patch fixes the bug reported by Eric Paris at:
http://bugzilla.kernel.org/show_bug.cgi?id=11838
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Acked-by: Eric Sandeen <sandeen@redhat.com>
Tested-by: Eric Paris <eparis@redhat.com>
Vegard Nossum reported a bug which accesses freed memory (found via
kmemcheck). When journal has been aborted, ext4_put_super() calls
ext4_abort() after freeing the journal_t object, and then ext4_abort()
accesses it. This patch fix it.
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Vegard Nossum reported a bug which accesses freed memory (found via
kmemcheck). When journal has been aborted, ext3_put_super() calls
ext3_abort() after freeing the journal_t object, and then ext3_abort()
accesses it. This patch fix it.
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Turned out some VMware userspace does pread(2) on /proc/uptime, but
seqfiles currently don't allow pread() resulting in -ESPIPE.
Seqfiles in theory can do pread(), but this can be a long story,
so revert to ->read_proc until then.
http://bugzilla.kernel.org/show_bug.cgi?id=11856
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
In commit f337b9c583 ("epoll: drop
unnecessary test") Thomas found that there is an unnecessary (always
true) test in ep_send_events(). The callback never inserts into
->rdllink while the send loop is performed, and also does the
~EP_PRIVATE_BITS test. Given we're holding the mutex during this time,
the conditions tested inside the loop are always true.
HOWEVER.
The test "!ep_is_linked(&epi->rdllink)" wasn't there because we insert
into ->rdllink, but because the send-events loop might terminate before
the whole list is scanned (-EFAULT).
In such cases, when the loop terminates early, and when a (leftover)
file received an event while we're performing the lockless loop, we need
such test to avoid to double insert the epoll items. The list_splice()
done a few steps below, will correctly re-insert the ones that were left
on "txlist".
This should fix the kenrel.org bugzilla entry 11831.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some userland apps seem to pass in a "0" for the seconds, and several
seconds worth of usecs to select(). The old kernels accepted this just
fine, so the new kernels must too.
However, due to the upscaling of the microseconds to nanoseconds we had
some cases where we got math overflow, and depending on the GCC version
(due to inlining decisions) that actually resulted in an -EINVAL return.
This patch fixes this by adding the excess microseconds to the seconds
field.
Also with thanks to Marcin Slusarz for spotting some implementation bugs
in the diagnostics patches.
Reported-by: Carlos R. Mafra <crmafra2@gmail.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a regression caused by commit d0156417, "ext4: fix ext4_dx_readdir
hash collision handling", where deleting files in a large directory
(requiring more than one getdents system call), results in some
filenames being returned twice. This was caused by a failure to
update info->curr_hash and info->curr_minor_hash, so that if the
directory had gotten modified since the last getdents() system call
(as would be the case if the user is running "rm -r" or "git clean"),
a directory entry would get returned twice to the userspace.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This patch fixes the bug reported by Markus Trippelsdorf at:
http://bugzilla.kernel.org/show_bug.cgi?id=11844
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Fix a regression caused by commit 6a897cf4, "ext3: fix ext3_dx_readdir
hash collision handling", where deleting files in a large directory
(requiring more than one getdents system call), results in some
filenames being returned twice. This was caused by a failure to
update info->curr_hash and info->curr_minor_hash, so that if the
directory had gotten modified since the last getdents() system call
(as would be the case if the user is running "rm -r" or "git clean"),
a directory entry would get returned twice to the userspace.
This patch fixes the bug reported by Markus Trippelsdorf at:
http://bugzilla.kernel.org/show_bug.cgi?id=11844
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
[ All users removed in "switch all filesystems over to d_obtain_alias",
aka commit 440037287c ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This one was due to a merge error: we added a use of nd.path in commit
2d7c820e56 ("ext3: add checks for errors
from jbd"), and concurrently we got rid of 'nd' and used a naked 'path'
in commit 8264613def ("[PATCH] switch
quota_on-related stuff to kern_path()").
That all merged cleanly, but it didn't actually _work_. This should fix
it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'v28-range-hrtimers-for-linus-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (37 commits)
hrtimers: add missing docbook comments to struct hrtimer
hrtimers: simplify hrtimer_peek_ahead_timers()
hrtimers: fix docbook comments
DECLARE_PER_CPU needs linux/percpu.h
hrtimers: fix typo
rangetimers: fix the bug reported by Ingo for real
rangetimer: fix BUG_ON reported by Ingo
rangetimer: fix x86 build failure for the !HRTIMERS case
select: fix alpha OSF wrapper
select: fix alpha OSF wrapper
hrtimer: peek at the timer queue just before going idle
hrtimer: make the futex() system call use the per process slack value
hrtimer: make the nanosleep() syscall use the per process slack
hrtimer: fix signed/unsigned bug in slack estimator
hrtimer: show the timer ranges in /proc/timer_list
hrtimer: incorporate feedback from Peter Zijlstra
hrtimer: add a hrtimer_start_range() function
hrtimer: another build fix
hrtimer: fix build bug found by Ingo
hrtimer: make select() and poll() use the hrtimer range feature
...
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: handle the TCP_Server_Info->tsk field more carefully
cifs: fix unlinking of rename target when server doesn't support open file renames
[CIFS] improve setlease handling
[CIFS] fix saving of resume key before CIFSFindNext
cifs: make cifs_rename handle -EACCES errors
[CIFS] fix build error
[CIFS] undo changes in cifs_rename_pending_delete if it errors out
cifs: track DeletePending flag in cifsInodeInfo
cifs: don't use CREATE_DELETE_ON_CLOSE in cifs_rename_pending_delete
[CIFS] eliminate usage of kthread_stop for cifsd
[CIFS] Add nodfs mount option
* git://git.kernel.org/pub/scm/linux/kernel/git/viro/bdev: (66 commits)
[PATCH] kill the rest of struct file propagation in block ioctls
[PATCH] get rid of struct file use in blkdev_ioctl() BLKBSZSET
[PATCH] get rid of blkdev_locked_ioctl()
[PATCH] get rid of blkdev_driver_ioctl()
[PATCH] sanitize blkdev_get() and friends
[PATCH] remember mode of reiserfs journal
[PATCH] propagate mode through swsusp_close()
[PATCH] propagate mode through open_bdev_excl/close_bdev_excl
[PATCH] pass fmode_t to blkdev_put()
[PATCH] kill the unused bsize on the send side of /dev/loop
[PATCH] trim file propagation in block/compat_ioctl.c
[PATCH] end of methods switch: remove the old ones
[PATCH] switch sr
[PATCH] switch sd
[PATCH] switch ide-scsi
[PATCH] switch tape_block
[PATCH] switch dcssblk
[PATCH] switch dasd
[PATCH] switch mtd_blkdevs
[PATCH] switch mmc
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
9p: fix sparse warnings
9p: rdma: RDMA Transport Support for 9P
9p: fix format warning
9p: fix debug build error
* 'for-2.6.28' of git://linux-nfs.org/~bfields/linux:
nfsd: clean up expkey_parse error cases
nfsd: Drop reference in expkey_parse error cases
nfsd: Fix memory leak in nfsd_getxattr
NFSD: Fix BUG during NFSD shutdown processing
The __log_wait_for_space function sits in a loop checkpointing
transactions until there is sufficient space free in the journal.
However, if there are no transactions to be processed (e.g. because the
free space calculation is wrong due to a corrupted filesystem) it will
never progress.
Check for space being required when no transactions are outstanding and
abort the journal instead of endlessly looping.
This patch fixes the bug reported by Sami Liedes at:
http://bugzilla.kernel.org/show_bug.cgi?id=10976
Signed-off-by: Duane Griffin <duaneg@dghda.com>
Tested-by: Sami Liedes <sliedes@cc.hut.fi>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__try_to_free_cp_buf(), __process_buffer(), and __wait_cp_io() test
BH_Uptodate flag to detect write I/O errors on metadata buffers. But by
commit 95450f5a7e "ext3: don't read inode
block if the buffer has a write error"(*), BH_Uptodate flag can be set to
inode buffers with BH_Write_EIO in order to avoid reading old inode data.
So now, we have to test BH_Write_EIO flag of checkpointing inode buffers
instead of BH_Uptodate. This patch does it.
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Acked-by: Jan Kara <jack@suse.cz>
Acked-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the journal has aborted due to a checkpointing failure, we have to
keep the contents of the journal space. Otherwise, the filesystem will
lose uncheckpointed metadata completely and become inconsistent. To
avoid this, we need to keep needs_recovery flag if checkpoint has
failed.
With this patch, ext3_put_super() detects a checkpointing failure from
the return value of journal_destroy(), then it invokes ext3_abort() to
make the filesystem read only and keep needs_recovery flag. Errors
from journal_flush() are also handled by this patch in some places.
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: Jan Kara <jack@ucw.cz>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a checkpointing IO fails, current JBD code doesn't check the error
and continue journaling. This means latest metadata can be lost from both
the journal and filesystem.
This patch leaves the failed metadata blocks in the journal space and
aborts journaling in the case of log_do_checkpoint(). To achieve this, we
need to do:
1. don't remove the failed buffer from the checkpoint list where in
the case of __try_to_free_cp_buf() because it may be released or
overwritten by a later transaction
2. log_do_checkpoint() is the last chance, remove the failed buffer
from the checkpoint list and abort the journal
3. when checkpointing fails, don't update the journal super block to
prevent the journaled contents from being cleaned. For safety,
don't update j_tail and j_tail_sequence either
4. when checkpointing fails, notify this error to the ext3 layer so
that ext3 don't clear the needs_recovery flag, otherwise the
journaled contents are ignored and cleaned in the recovery phase
5. if the recovery fails, keep the needs_recovery flag
6. prevent cleanup_journal_tail() from being called between
__journal_drop_transaction() and journal_abort() (a race issue
between journal_flush() and __log_wait_for_space()
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Acked-by: Jan Kara <jack@suse.cz>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lose dummy ->write hook in case of SLUB, it's possible now.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Use WARN() rather than a printk() + backtrace();
this gives a more standard format message as well as complete
information (including line numbers etc) that will be collected
by kerneloops.org
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Commit 4752c36978 aka
"maps4: simplify interdependence of maps and smaps" broke /proc/pid/smaps,
causing it to display some vmas twice and other vmas not at all. For example:
grep .- /proc/1/smaps >/tmp/smaps; diff /proc/1/maps /tmp/smaps
1 25d24
2 < 7fd7e23aa000-7fd7e23ac000 rw-p 7fd7e23aa000 00:00 0
3 28a28
4 > ffffffffff600000-ffffffffff601000 r-xp 00000000 00:00 0 [vsyscall]
The bug has something to do with setting m->version before all the
seq_printf's have been performed. show_map was doing this correctly,
but show_smap was doing this in the middle of its seq_printf sequence.
This patch arranges things so that the setting of m->version in show_smap
is also done at the end of its seq_printf sequence.
Testing: in addition to the above grep test, for each process I summed
up the 'Rss' fields of /proc/pid/smaps and compared that to the 'VmRSS'
field of /proc/pid/status. All matched except for Xorg (which has a
/dev/mem mapping which Rss accounts for but VmRSS does not). This result
gives us some confidence that neither /proc/pid/maps nor /proc/pid/smaps
are any longer skipping or double-counting vmas.
Signed-off-by: Joe Korty <joe.korty@ccur.com>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Hi Al,
remember that debug session we did at KS? You suggested this patch back
then....
From 7751eaf30474b8cbfaea64795805a17eab05ac53 Mon Sep 17 00:00:00 2001
From: Arjan van de Ven <arjan@linux.intel.com>
Date: Tue, 16 Sep 2008 16:51:17 -0700
Subject: [PATCH] fs: add a sanity check in d_free
we're seeing some corruption in the dentry->d_alias list that
appears like a free of an entry still on the list; this patch
adds a WARN_ON() to catch this scenario, as suggested by Al Viro
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Call security_inode_setattr() consistetly before inode_change_ok().
It doesn't make sense to try to "optimize" the i_op->setattr == NULL
case, as most filesystem do define their own setattr function.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Assume you have:
- one or more of ext2/3/4 statically built into your kernel
- none of these with extended attributes enabled and
- want to add onother one of ext2/3/4 modular and with
extended attributes enabled
then you currently have to reboot to use it since this results in
CONFIG_FS_MBCACHE=y.
That's not a common issue, but I just ran into it and since there's no
reason to get a built-in mbcache in this case this patch fixes it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Andreas Gruenbacher <agruen@suse.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
For execute permission on a regular files we need to check if file has
any execute bits at all, regardless of capabilites.
This check is normally performed by generic_permission() but was also
added to the case when the filesystem defines its own ->permission()
method. In the latter case the filesystem should be responsible for
performing this check.
Move the check from inode_permission() inside filesystems which are
not calling generic_permission().
Create a helper function execute_ok() that returns true if the inode
is a directory or if any execute bits are present in i_mode.
Also fix up the following code:
- coda control file is never executable
- sysctl files are never executable
- hfs_permission seems broken on MAY_EXEC, remove
- hfsplus_permission is eqivalent to generic_permission(), remove
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Daemons that need to be launched while the rootfs is read-only can now
poll /proc/mounts to be notified when their O_RDWR requests may no
longer end in EROFS.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reiserfs currently doesn't set a llseek method for regular files, which
means it will fall back to default_llseek. This means no one can seek
beyond 2 Gigabytes on reiserfs, and that there's not protection vs
the i_size updates from writers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
With this patch all directory fops instances that have a readdir
that doesn't take the BKL are switched to generic_file_llseek.
Signed-off-by: Christoph Hellwig <hch@lst.de>
This adds LOOKUP_RENAME_TARGET intent for lookup of rename destination.
LOOKUP_RENAME_TARGET is going to be used like LOOKUP_CREATE. But since
the destination of rename() can be existing directory entry, so it has a
difference. Although that difference doesn't matter in my usage, this
tells it to user of this intent.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
lookup_hash() with LOOKUP_PARENT is bogus. And this prepares to add
new intent on those path.
The user of LOOKUP_PARENT intent is nfs only, and it checks whether
nd->flags has LOOKUP_CREATE or LOOKUP_OPEN, so the result is same.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
This adds __d_instantiate() for users which is already taking
dcache_lock, and replace with it.
The part of d_add_ci() isn't equivalent. But it should be needed
fsnotify_d_instantiate() actually, because the path is to add the
inode to negative dentry. fsnotify_d_instantiate() should be called
after change from negative to positive.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
This adds d_ancestor() instead of d_isparent(), then use it.
If new_dentry == old_dentry, is_subdir() returns 1, looks strange.
"new_dentry == old_dentry" is not subdir obviously. But I'm not
checking callers for now, so this keeps current behavior.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Now that JFFS2 can be exported by NFS, we need to get this right.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Avoid calling the underlying ->readdir() again when we reached the end
already; keep going round the loop only if we stopped due to our own
buffer being full.
[AV: tidy the things up a bit, while we are there]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
It's not the final state, but it allows moving ->readdir() instances
to passing filldir return value to caller of vfs_readdir().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Better pass parent and qstr to ext3_find_entry() explicitly than
use such kludges, especially since the stack footprint is nasty
enough and we have every chance to be deep in call chain.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Now that the readdir/lookup deadlock issues have been dealt with, we can
export JFFS2 file systems again.
(For now, you have to specify fsid manually; we should add a method to
the export_ops to handle that too.)
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Now that we've moved the readdir hack to the nfsd code, we can
remove the local version from the XFS code.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Some file systems with their own internal locking have problems with the
way that nfsd calls the ->lookup() method from within a filldir function
called from their ->readdir() method. The recursion back into the file
system code can cause deadlock.
XFS has a fairly hackish solution to this which involves doing the
readdir() into a locally-allocated buffer, then going back through it
calling the filldir function afterwards. It's not ideal, but it works.
It's particularly suboptimal because XFS does this for local file
systems too, where it's completely unnecessary.
Copy this hack into the NFS code where it can be used only for NFS
export. In response to feedback, use it unconditionally rather than only
for the affected file systems.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The calling conventions of d_alloc_anon are rather unfortunate for all
users, and it's name is not very descriptive either.
Add d_obtain_alias as a new exported helper that drops the inode
reference in the failure case, too and allows to pass-through NULL
pointers and inodes to allow for tail-calls in the export operations.
Incidentally this helper already existed as a private function in
libfs.c as exportfs_d_alloc so kill that one and switch the callers
to d_obtain_alias.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add kerneldoc for generic_file_llseek and generic_file_llseek_unlocked,
use sane variable names and unclutter the code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Use a single goto label for chrdev_put + return error cases.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reformat hpfs_notify_change to standard kernel style to make it readable
and rename it to hpfs_setattr as that's what the method is called.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
New flag: LOOKUP_EXCL. Set before doing the final step of pathname
resolution on the paths that have LOOKUP_CREATE and O_EXCL.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
... and don't pass bogus flags when we are just looking for parent.
Fold __path_lookup_intent_open() into path_lookup_open() while we
are at it; that's the only remaining caller.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
cifs: handle the TCP_Server_Info->tsk field more carefully
We currently handle the TCP_Server_Info->tsk field without any locking,
but with some half-measures to try and prevent races. These aren't
really sufficient though. When taking down cifsd, use xchg() to swap
the contents of the tsk field with NULL so we don't end up trying
to send it more than one signal. Also, don't allow cifsd to exit until
the signal is received if we expect one.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
cifs: fix unlinking of rename target when server doesn't support open file renames
The patch to make cifs_rename undoable broke renaming one file on top of
another when the server doesn't support busy file renames. Remove the
code that uses busy file renames to unlink the target file, and just
have it call cifs_unlink. If the rename of the source file fails, then
the unlink won't be undoable, but hopefully that's rare enough that it
won't be a problem.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
fcntl(F_SETLEASE) currently is not exported by cifs (nor by local file
systems) so cifs grants leases based on how other local processes have
opened the file not by whether the file is cacheable (oplocked). This
adds the check to make sure that the file is cacheable on the client
before checking whether we can grant the lease locally
(generic_setlease). It also adds a mount option for cifs (locallease)
if the user wants to override this and try to grant leases even
if the server did not grant oplock.
Signed-off-by: Steve French <sfrench@us.ibm.com>
We might as well do all of these at the end. Fix up a couple minor
style nits while we're there.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Drop reference to export key on error. Compile tested.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Fix a memory leak in nfsd_getxattr. nfsd_getxattr should free up memory
that it allocated if vfs_getxattr fails.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
The Linux NFS server can be started via a user-space write to
/proc/fs/nfs/threads or to /proc/fs/nfs/portlist. In the first case,
all default listeners are started (both UDP and TCP). In the second,
a listener is started only for one specified transport.
The NFS server has to make sure lockd stays up until the last listener
transport goes away. To support both start-up interfaces, it should
do one lockd_up() for each NFSD listener.
The nfsd_init_socks() function used to do one lockd_up() call for each
svc_create_xprt(). Recently commit
26a4140923 mistakenly changed
nfsd_init_socks() to do only one lockd_up() call even though it still
does two svc_create_xprt() calls.
The end result is a lockd_down() BUG during NFSD shutdown processing
because nfsd_last_threads() does a lockd_down() call for each entry
on the sv_permsocks list, but the start-up code doesn't do a matching
number of lockd_up() calls.
Add a second lockd_up() in nfsd_init_socks() to make sure the number
of lockd_up() calls matches the number of entries on the NFS servers's
sv_permsocks list.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
We recently fixed the cifs readdir code so that it saves the resume key
before calling CIFSFindNext. Unfortunately, this assumes that we have
just done a CIFSFindFirst (or FindNext) and have resume info to save.
This isn't necessarily the case. Fix the code to save resume info if we
had to reinitiate the search, and after a FindNext.
This fixes connectathon basic test6 against NetApp filers.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
CC: Stable <stable@kernel.org>
Signed-off-by: Steve French <sfrench@us.ibm.com>
* get rid of fake struct file/struct dentry in __blkdev_get()
* merge __blkdev_get() and do_open()
* get rid of flags argument of blkdev_get()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
replace open_bdev_excl/close_bdev_excl with variants taking fmode_t.
superblock gets the value used to mount it stored in sb->s_mode
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
To keep the size of changesets sane we split the switch by drivers;
to keep the damn thing bisectable we do the following:
1) rename the affected methods, add ones with correct
prototypes, make (few) callers handle both. That's this changeset.
2) for each driver convert to new methods. *ALL* drivers
are converted in this series.
3) kill the old (renamed) methods.
Note that it _is_ a flagday; all in-tree drivers are converted and by the
end of this series no trace of old methods remain. The only reason why
we do that this way is to keep the damn thing bisectable and allow per-driver
debugging if anything goes wrong.
New methods:
open(bdev, mode)
release(disk, mode)
ioctl(bdev, mode, cmd, arg) /* Called without BKL */
compat_ioctl(bdev, mode, cmd, arg)
locked_ioctl(bdev, mode, cmd, arg) /* Called with BKL, legacy */
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Commit f06febc96b ("timers: fix itimer/
many thread hang") introduced a new task_cputime interface and
subsequently only converted binfmt_elf over to it. This results in the
build for binfmt_elf_fdpic blowing up given that p->signal->{u,s}time
have disappeared from underneath us.
Apply the same trivial fix from binfmt_elf to binfmt_elf_fdpic.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This merges branches irq/genirq, irq/sparseirq-v4, timers/hpet-percpu
and x86/uv.
The sparseirq branch is just preliminary groundwork: no sparse IRQs are
actually implemented by this tree anymore - just the new APIs are added
while keeping the old way intact as well (the new APIs map 1:1 to
irq_desc[]). The 'real' sparse IRQ support will then be a relatively
small patch ontop of this - with a v2.6.29 merge target.
* 'genirq-v28-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (178 commits)
genirq: improve include files
intr_remapping: fix typo
io_apic: make irq_mis_count available on 64-bit too
genirq: fix name space collisions of nr_irqs in arch/*
genirq: fix name space collision of nr_irqs in autoprobe.c
genirq: use iterators for irq_desc loops
proc: fixup irq iterator
genirq: add reverse iterator for irq_desc
x86: move ack_bad_irq() to irq.c
x86: unify show_interrupts() and proc helpers
x86: cleanup show_interrupts
genirq: cleanup the sparseirq modifications
genirq: remove artifacts from sparseirq removal
genirq: revert dynarray
genirq: remove irq_to_desc_alloc
genirq: remove sparse irq code
genirq: use inline function for irq_to_desc
genirq: consolidate nr_irqs and for_each_irq_desc()
x86: remove sparse irq from Kconfig
genirq: define nr_irqs for architectures with GENERIC_HARDIRQS=n
...
* 'v28-timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (36 commits)
fix documentation of sysrq-q really
Fix documentation of sysrq-q
timer_list: add base address to clock base
timer_list: print cpu number of clockevents device
timer_list: print real timer address
NOHZ: restart tick device from irq_enter()
NOHZ: split tick_nohz_restart_sched_tick()
NOHZ: unify the nohz function calls in irq_enter()
timers: fix itimer/many thread hang, fix
timers: fix itimer/many thread hang, v3
ntp: improve adjtimex frequency rounding
timekeeping: fix rounding problem during clock update
ntp: let update_persistent_clock() sleep
hrtimer: reorder struct hrtimer to save 8 bytes on 64bit builds
posix-timers: lock_timer: make it readable
posix-timers: lock_timer: kill the bogus ->it_id check
posix-timers: kill ->it_sigev_signo and ->it_sigev_value
posix-timers: sys_timer_create: cleanup the error handling
posix-timers: move the initialization of timer->sigq from send to create path
posix-timers: sys_timer_create: simplify and s/tasklist/rcu/
...
Fix trivial conflicts due to sysrq-q description clahes in
Documentation/sysrq.txt and drivers/char/sysrq.c
cifs: make cifs_rename handle -EACCES errors
Some servers seem to return -EACCES when attempting to rename one
open file on top of another. Refactor the cifs_rename logic to
attempt to rename the target file out of the way in this situation.
This also fixes the "unlink_target" logic to be undoable if the
subsequent rename fails.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Use fs/*/Kconfig more, which is good because everything related to one
filesystem is in one place and fs/Kconfig is quite fat.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs: (26 commits)
9p: add more conservative locking
9p: fix oops in protocol stat parsing error path.
9p: fix device file handling
9p: Improve debug support
9p: eliminate depricated conv functions
9p: rework client code to use new protocol support functions
9p: remove unnecessary tag field from p9_req_t structure
9p: remove 9p fcall debug prints
9p: add new protocol support code
9p: encapsulate version function
9p: move dirread to fs layer
9p: adjust 9p vfs write operation
9p: move readn meta-function from client to fs layer
9p: consolidate read/write functions
9p: drop broken unused error path from p9_conn_create()
9p: make rpc code common and rework flush code
9p: use the rcall structure passed in the request in trans_fd read_work
9p: apply common request code to trans_fd
9p: apply common tagpool handling to trans_fd
9p: move request management to client code
...
* git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: use correct fs type for v4 submounts and referrals
Make nfs_file_cred more robust.
NFS: Enable NFSv4 callback server to listen on AF_INET6 sockets
* 'linux-next' of git://git.infradead.org/ubifs-2.6: (25 commits)
UBIFS: fix ubifs_compress commentary
UBIFS: amend printk
UBIFS: do not read unnecessary bytes when unpacking bits
UBIFS: check buffer length when scanning for LPT nodes
UBIFS: correct condition to eliminate unecessary assignment
UBIFS: add more debugging messages for LPT
UBIFS: fix bulk-read handling uptodate pages
UBIFS: improve garbage collection
UBIFS: allow for sync_fs when read-only
UBIFS: commit on sync_fs
UBIFS: correct comment for commit_on_unmount
UBIFS: update dbg_dump_inode
UBIFS: fix commentary
UBIFS: fix races in bit-fields
UBIFS: ensure data read beyond i_size is zeroed out correctly
UBIFS: correct key comparison
UBIFS: use bit-fields when possible
UBIFS: check data CRC when in error state
UBIFS: improve znode splitting rules
UBIFS: add no_chk_data_crc mount option
...
* git://git.infradead.org/mtd-2.6: (69 commits)
Revert "[MTD] m25p80.c code cleanup"
[MTD] [NAND] GPIO driver depends on ARM... for now.
[MTD] [NAND] sh_flctl: fix compile error
[MTD] [NOR] AT49BV6416 has swapped erase regions
[MTD] [NAND] GPIO NAND flash driver
[MTD] cmdlineparts documentation change - explain where mtd-id comes from
[MTD] cfi_cmdset_0002.c: Add Macronix CFI V1.0 TopBottom detection
[MTD] [NAND] Fix compilation warnings in drivers/mtd/nand/cs553x_nand.c
[JFFS2] Write buffer offset adjustment for NOR-ECC (Sibley) flash
[MTD] mtdoops: Fix a bug where block may not be erased
[MTD] mtdoops: Add a magic number to logged kernel oops
[MTD] mtdoops: Fix an off by one error
[JFFS2] Correct parameter names of jffs2_compress() in comments
[MTD] [NAND] sh_flctl: add support for Renesas SuperH FLCTL
[MTD] [NAND] Bug on atmel_nand HW ECC : OOB info not correctly written
[MTD] [MAPS] Remove unused variable after ROM API cleanup.
[MTD] m25p80.c extended jedec support (v2)
[MTD] remove unused mtd parameter in of_mtd_parse_partitions()
[MTD] [NAND] remove dead Kconfig associated with !CONFIG_PPC_MERGE
[MTD] [NAND] driver extension to support NAND on TQM85xx modules
...
The usage of elfcorehdr_addr has changed recently such that being set to
ELFCORE_ADDR_MAX is used by is_kdump_kernel() to indicate if the code is
executing in a kernel executed as a crash kernel.
However, arch/ia64/kernel/setup.c:reserve_elfcorehdr will rest
elfcorehdr_addr to ELFCORE_ADDR_MAX on error, which means any subsequent
calls to is_kdump_kernel() will return 0, even though they should return
1.
Ok, at this point in time there are no subsequent calls, but I think its
fair to say that there is ample scope for error or at the very least
confusion.
This patch add an extra state, ELFCORE_ADDR_ERR, which indicates that
elfcorehdr_addr was passed on the command line, and thus execution is
taking place in a crashdump kernel, but vmcore can't be used for some
reason. This is tested for using is_vmcore_usable() and set using
vmcore_unusable(). A subsequent patch makes use of this new code.
To summarise, the states that elfcorehdr_addr can now be in are as follows:
ELFCORE_ADDR_MAX: not a crashdump kernel
ELFCORE_ADDR_ERR: crashdump kernel but vmcore is unusable
any other value: crash dump kernel and vmcore is usable
Signed-off-by: Simon Horman <horms@verge.net.au>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
o elfcorehdr_addr is used by not only the code under CONFIG_PROC_VMCORE
but also by the code which is not inside CONFIG_PROC_VMCORE. For
example, is_kdump_kernel() is used by powerpc code to determine if
kernel is booting after a panic then use previous kernel's TCE table.
So even if CONFIG_PROC_VMCORE is not set in second kernel, one should be
able to correctly determine that we are booting after a panic and setup
calgary iommu accordingly.
o So remove the assumption that elfcorehdr_addr is under
CONFIG_PROC_VMCORE.
o Move definition of elfcorehdr_addr to arch dependent crash files.
(Unfortunately crash dump does not have an arch independent file
otherwise that would have been the best place).
o kexec.c is not the right place as one can Have CRASH_DUMP enabled in
second kernel without KEXEC being enabled.
o I don't see sh setup code parsing the command line for
elfcorehdr_addr. I am wondering how does vmcore interface work on sh.
Anyway, I am atleast defining elfcoredhr_addr so that compilation is not
broken on sh.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a kconfig option to change the /proc/PID/coredump_filter default.
Fedora has been carrying a trivial patch to change the hard-wired value for
this default, since Fedora 8. The default default can't change safely
because there are old GDB versions out there (all before 6.7) that are
confused by the core dump files created by the MMF_DUMP_ELF_HEADERS setting.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Kawai Hidehiro <hidehiro.kawai.ez@hitachi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the coredumping is multi-threaded, format_corename() appends .%pid to
the corename. This was needed before the proper multi-thread core dump
support, now all the threads in the mm go into a single unified core file.
Remove this special case, it is not even documented and we have "%p"
and core_uses_pid.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Roland McGrath <roland@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: La Monte Yarroll <piggy@laurelnetworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
seq_cpumask_list(), seq_nodemask_list() are very like seq_cpumask(),
seq_nodemask(), but they print human readable string.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Paul Menage <menage@google.com>
Cc: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"m->count + len < m->size" is true commonly, so bitmap_scnprintf()
is commonly called. this fix saves a call to bitmap_scnprintf_len().
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Paul Menage <menage@google.com>
Cc: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A corrupted extent for the extent file itself may try to get an impossible
extent, causing a deadlock if I see it correctly.
Check the inode number after the first_blocks checks and fail if it's the
extent file, as according to the spec the extent file should have no
extent for itself.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A very large directory with many read failures (either due to storage
problems, or due to invalid size & blocks from corruption) will generate a
printk storm as the filesystem continues to try to read all the blocks.
This flood of messages can tie up the box until it is complete - which may
be a very long time, especially for very large corrupted values.
This is fixed by only reporting the corruption once each time we try to
read the directory.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Eugene Teo <eugeneteo@kernel.sg>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For blocksize < pagesize we need to remove blocks that got allocated in
block_write_begin() if we fail with ENOSPC for later blocks.
block_write_begin() internally does this if it allocated page locally.
This makes sure we don't have blocks outside inode.i_size during ENOSPC.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a bug where readdir() would return a directory entry twice
if there was a hash collision in an hash tree indexed directory.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Eugene Dashevsky <eugene@ibrix.com>
Signed-off-by: Mike Snitzer <msnitzer@ibrix.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In ordered mode, if a file data buffer being dirtied exists in the
committing transaction, we write the buffer to the disk, move it from the
committing transaction to the running transaction, then dirty it. But we
don't have to remove the buffer from the committing transaction when the
buffer couldn't be written out, otherwise it would miss the error and the
committing transaction would not abort.
This patch adds an error check before removing the buffer from the
committing transaction.
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the journal doesn't abort when it gets an IO error in file data blocks,
the file data corruption will spread silently. Because most of
applications and commands do buffered writes without fsync(), they don't
notice the IO error. It's scary for mission critical systems. On the
other hand, if the journal aborts whenever it gets an IO error in file
data blocks, the system will easily become inoperable. So this patch
introduces a filesystem option to determine whether it aborts the journal
or just call printk() when it gets an IO error in file data.
If you mount a ext3 fs with data_err=abort option, it aborts on file data
write error. If you mount it with data_err=ignore, it doesn't abort, just
call printk(). data_err=ignore is the default.
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: Jan Kara <jack@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We could run into ENOSPC error on ext3, even when there is free blocks on
the filesystem.
The problem is triggered in the case the goal block group has 0 free
blocks , and the rest block groups are skipped due to the check of
"free_blocks < windowsz/2". Current code could fall back to non
reservation allocation to prevent early ENOSPC after examing all the block
groups with reservation on , but this code was bypassed if the reservation
window is turned off already, which is true in this case.
This patch fixed two issues:
1) We don't need to turn off block reservation if the goal block group has
0 free blocks left and continue search for the rest of block groups.
Current code the intention is to turn off the block reservation if the
goal allocation group has a few (some) free blocks left (not enough for
make the desired reservation window),to try to allocation in the goal
block group, to get better locality. But if the goal blocks have 0 free
blocks, it should leave the block reservation on, and continues search for
the next block groups,rather than turn off block reservation completely.
2) we don't need to check the window size if the block reservation is off.
The problem was originally found and fixed in ext4.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When trying to resize a ext3 fs and you run out of reserved gdt blocks,
you get an error that doesn't actually tell you what went wrong, it just
says that the gdb it picked is not correct, which is the case since you
don't have any reserved gdt blocks left. This patch adds a check to make
sure you have reserved gdt blocks to use, and if not prints out a more
relevant error.
Signed-off-by: Josef Bacik <jbacik@redhat.com>
Cc: <linux-ext4@vger.kernel.org>
Cc: Andreas Dilger <adilger@sun.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, original metadata buffers are dirtied when they are unfiled
whether the journal has aborted or not. Eventually these buffers will be
written-back to the filesystem by pdflush. This means some metadata
buffers are written to the filesystem without journaling if the journal
aborts. So if both journal abort and system crash happen at the same
time, the filesystem would become inconsistent state. Additionally,
replaying journaled metadata can overwrite the latest metadata on the
filesystem partly. Because, if the journal aborts, journaled metadata are
preserved and replayed during the next mount not to lose uncheckpointed
metadata. This would also break the consistency of the filesystem.
This patch prevents original metadata buffers from being dirtied on abort
by clearing BH_JBDDirty flag from those buffers. Thus, no metadata
buffers are written to the filesystem without journaling.
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Acked-by: Jan Kara <jack@suse.cz>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we failed to write metadata buffers to the journal space and succeeded
to write the commit record, stale data can be written back to the
filesystem as metadata in the recovery phase.
To avoid this, when we failed to write out metadata buffers, abort the
journal before writing the commit record.
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Acked-by: Jan Kara <jack@suse.cz>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Presently hugepage's vma has a VM_RESERVED flag in order not to be
swapped. But a VM_RESERVED vma isn't core dumped because this flag is
often used for some kernel vmas (e.g. vmalloc, sound related).
Thus hugepages are never dumped and it can't be debugged easily. Many
developers want hugepages to be included into core-dump.
However, We can't read generic VM_RESERVED area because this area is often
IO mapping area. then these area reading may change device state. it is
definitly undesiable side-effect.
So adding a hugepage specific bit to the coredump filter is better. It
will be able to hugepage core dumping and doesn't cause any side-effect to
any i/o devices.
In additional, libhugetlb use hugetlb private mapping pages as anonymous
page. Then, hugepage private mapping pages should be core dumped by
default.
Then, /proc/[pid]/core_dump_filter has two new bits.
- bit 5 mean hugetlb private mapping pages are dumped or not. (default: yes)
- bit 6 mean hugetlb shared mapping pages are dumped or not. (default: no)
I tested by following method.
% ulimit -c unlimited
% ./crash_hugepage 50
% ./crash_hugepage 50 -p
% ls -lh
% gdb ./crash_hugepage core
%
% echo 0x43 > /proc/self/coredump_filter
% ./crash_hugepage 50
% ./crash_hugepage 50 -p
% ls -lh
% gdb ./crash_hugepage core
#include <stdlib.h>
#include <stdio.h>
#include <unistd.h>
#include <sys/mman.h>
#include <string.h>
#include "hugetlbfs.h"
int main(int argc, char** argv){
char* p;
int ch;
int mmap_flags = MAP_SHARED;
int fd;
int nr_pages;
while((ch = getopt(argc, argv, "p")) != -1) {
switch (ch) {
case 'p':
mmap_flags &= ~MAP_SHARED;
mmap_flags |= MAP_PRIVATE;
break;
default:
/* nothing*/
break;
}
}
argc -= optind;
argv += optind;
if (argc == 0){
printf("need # of pages\n");
exit(1);
}
nr_pages = atoi(argv[0]);
if (nr_pages < 2) {
printf("nr_pages must >2\n");
exit(1);
}
fd = hugetlbfs_unlinked_fd();
p = mmap(NULL, nr_pages * gethugepagesize(),
PROT_READ|PROT_WRITE, mmap_flags, fd, 0);
sleep(2);
*(p + gethugepagesize()) = 1; /* COW */
sleep(2);
/* crash! */
*(int*)0 = 1;
return 0;
}
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reviewed-by: Kawai Hidehiro <hidehiro.kawai.ez@hitachi.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: William Irwin <wli@holomorphy.com>
Cc: Adam Litke <agl@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
trylock_buffer and unlock_buffer open and close a critical section.
Hence, we can use the lock bitops to get the desired memory ordering.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add NR_MLOCK zone page state, which provides a (conservative) count of
mlocked pages (actually, the number of mlocked pages moved off the LRU).
Reworked by lts to fit in with the modified mlock page support in the
Reclaim Scalability series.
[kosaki.motohiro@jp.fujitsu.com: fix incorrect Mlocked field of /proc/meminfo]
[lee.schermerhorn@hp.com: mlocked-pages: add event counting with statistics]
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph Lameter pointed out that ram disk pages also clutter the LRU
lists. When vmscan finds them dirty and tries to clean them, the ram disk
writeback function just redirties the page so that it goes back onto the
active list. Round and round she goes...
With the ram disk driver [rd.c] replaced by the newer 'brd.c', this is no
longer the case, as ram disk pages are no longer maintained on the lru.
[This makes them unmigratable for defrag or memory hot remove, but that
can be addressed by a separate patch series.] However, the ramfs pages
behave like ram disk pages used to, so:
Define new address_space flag [shares address_space flags member with
mapping's gfp mask] to indicate that the address space contains all
unevictable pages. This will provide for efficient testing of ramfs pages
in page_evictable().
Also provide wrapper functions to set/test the unevictable state to
minimize #ifdefs in ramfs driver and any other users of this facility.
Set the unevictable state on address_space structures for new ramfs
inodes. Test the unevictable state in page_evictable() to cull
unevictable pages.
These changes depend on [CONFIG_]UNEVICTABLE_LRU.
[riel@redhat.com: undo the brd.c part]
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Signed-off-by: Rik van Riel <riel@redhat.com>
Debugged-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Report unevictable pages per zone and system wide.
Kosaki Motohiro added support for memory controller unevictable
statistics.
[riel@redhat.com: fix printk in show_free_areas()]
[akpm@linux-foundation.org: fix units in /proc/vmstats]
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Debugged-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Split the LRU lists in two, one set for pages that are backed by real file
systems ("file") and one for pages that are backed by memory and swap
("anon"). The latter includes tmpfs.
The advantage of doing this is that the VM will not have to scan over lots
of anonymous pages (which we generally do not want to swap out), just to
find the page cache pages that it should evict.
This patch has the infrastructure and a basic policy to balance how much
we scan the anon lists and how much we scan the file lists. The big
policy changes are in separate patches.
[lee.schermerhorn@hp.com: collect lru meminfo statistics from correct offset]
[kosaki.motohiro@jp.fujitsu.com: prevent incorrect oom under split_lru]
[kosaki.motohiro@jp.fujitsu.com: fix pagevec_move_tail() doesn't treat unevictable page]
[hugh@veritas.com: memcg swapbacked pages active]
[hugh@veritas.com: splitlru: BDI_CAP_SWAP_BACKED]
[akpm@linux-foundation.org: fix /proc/vmstat units]
[nishimura@mxp.nes.nec.co.jp: memcg: fix handling of shmem migration]
[kosaki.motohiro@jp.fujitsu.com: adjust Quicklists field of /proc/meminfo]
[kosaki.motohiro@jp.fujitsu.com: fix style issue of get_scan_ratio()]
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The cifs_rename_pending_delete process involves multiple steps. If it
fails and we're going to return error, we don't want to leave things in
a half-finished state. Add code to the function to undo changes if
a call fails.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
cifs: track DeletePending flag in cifsInodeInfo
The QPathInfo call returns a flag that indicates whether DELETE_ON_CLOSE
is set. Track it in the cifsInodeInfo.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Update the comment for ubifs_compress(), which incorrectly states that it
returnsa success/failure indicator.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
It is better to print "Reserved for root" than
"Reserved pool size", because it is more obvious for users
what this means.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
After choosing new c->nextblock, don't leave the wbuf offset field
occasionally pointing at the start of the next physical eraseblock.
This was causing a BUG() on NOR-ECC (Sibley) flash, where we start
writing after the cleanmarker.
Among other this fix should cover write buffer offset adjustment
after flushing the last page of an eraseblock.
Signed-off-by: Alexander Belyakov <abelyako@googlemail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: Remove automatic enabling of the HUGE_FILE feature flag
ext4: Replace hackish ext4_mb_poll_new_transaction with commit callback
ext4: Update Documentation/filesystems/ext4.txt
ext4: Remove unused mount options: nomballoc, mballoc, nocheck
ext4: Remove compile warnings when building w/o CONFIG_PROC_FS
ext4: Add missing newlines to printk messages
ext4: Fix file fragmentation during large file write.
vfs: Add no_nrwrite_index_update writeback control flag
vfs: Remove the range_cont writeback mode.
ext4: Use tag dirty lookup during mpage_da_submit_io
ext4: let the block device know when unused blocks can be discarded
ext4: Don't reuse released data blocks until transaction commits
ext4: Use an rbtree for tracking blocks freed during transaction.
ext4: Do mballoc init before doing filesystem recovery
ext4: Free ext4_prealloc_space using kmem_cache_free
ext4: Fix Kconfig typo for ext4dev
ext4: Remove an old reference to ext4dev in Makefile comment
In v9fs_get_inode(), for block, as well as char devices (in theory),
the function init_special_inode() is called to set up callback functions
for file ops. this function uses the file mode's value to determine whether
to use block or char dev functions. In v9fs_inode_from_fid(), the function
p9mode2unixmode() is used, but for all devices it initially returns S_IFBLK,
then uses v9fs_get_inode() to initialise a new inode, then finally uses
v9fs_stat2inode(), which would determine whether the inode is a block or
character device. However, at that point init_special_inode() had already
decided to use the block device functions, so even if the inode's mode is
turned to a character device, the block functions are still used to operate
on them. The attached patch simply calls init_special_inode() again for devices
after parsing device node data in v9fs_stat2inode() so that the proper functions
are used.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
As not all files have an associated open_context (e.g. device special
files), it is safest to test for the existence of the open context
before de-referencing it.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Allow the NFS callback server to listen for requests via an AF_INET6 or
AF_INET socket when IPv6 support is present in the kernel.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Remove depricated conv functions which have been replaced with new
protocol routines.
This patch also reworks the one instance of the file-system code which
directly calls conversion routines (to accomplish unpacking dirreads).
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Now that the new protocol functions are in place, this patch switches
the client code to using the new support code.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Currently reading a directory is implemented in the client code.
This function is not actually a wire operation, but a meta operation
which calls read operations and processes the results.
This patch moves this functionality to the fs layer and calls component
wire operations instead of constructing their packets. This provides a
cleaner separation and will help when we reorganize the client functions
and protocol processing methods.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Currently, the 9p net wire operation ensures that all data is sent by sending
multiple packets if the data requested is larger than the msize. This is
better handled in the vfs code so that we can simplify wire operations to
being concerned with only putting data onto and taking data off of the wire.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
There are a couple of methods in the client code which aren't actually
wire operations. To keep things organized cleaner, these operations are
being moved to the fs layer.
This patch moves the readn meta-function (which executes multiple wire
reads until a buffer is full) to the fs layer.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Currently there are two separate versions of read and write. One for
dealing with user buffers and the other for dealing with kernel buffers.
There is a tremendous amount of code duplication in the otherwise
identical versions of these functions. This patch adds an additional
user buffer parameter to read and write and conditionalizes handling of
the buffer on whether the kernel buffer or the user buffer is populated.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Right now there is a transport module structure which provides per-transport
type functions and data and a transport structure which contains per-instance
public data as well as function pointers to instance specific functions.
This patch moves public transport visible instance data to the client
structure (which in some cases had duplicate data) and consolidates the
functions into the transport module structure.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Make the parameter names of jffs2_compress() in its comments match with the
actual implementation
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
cifs: don't use CREATE_DELETE_ON_CLOSE in cifs_rename_pending_delete
CREATE_DELETE_ON_CLOSE apparently has different semantics than when you
set the DELETE_ON_CLOSE bit after opening the file. Setting it in the
open says "delete this file as soon as this filehandle is closed". That's
not what we want for cifs_rename_pending_delete.
Don't set this bit in the CreateFlags. Experimentation shows that
setting this flag in the SET_FILE_INFO call has no effect.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Fix block kernel-doc warnings:
Warning(linux-2.6.27-git4//fs/block_dev.c:1272): No description found for parameter 'path'
Warning(linux-2.6.27-git4//block/blk-core.c:1021): No description found for parameter 'cpu'
Warning(linux-2.6.27-git4//block/blk-core.c:1021): No description found for parameter 'part'
Warning(/var/linsrc/linux-2.6.27-git4//block/genhd.c:544): No description found for parameter 'partno'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With extended devt, finding out the partition number becomes a bit
more challenging as subtracting the minor number from that of the
parent device doesn't work anymore. The only thing left is parsing
the partition name which is brittle and not exactly universal (some
have '-' between the device name and partition number while others
don't). This patch introduced partition attribute which contains the
partition number of the device. This should make finding partitions
and its index easier.
This problem and solution were suggested by H. Peter Anvin.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
If the HUGE_FILE feature flag is not set, don't allow the creation of
large files, instead of automatically enabling the feature flag.
Recent versions of mke2fs will set the HUGE_FILE flag automatically
anyway for ext4 filesystems.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The multiblock allocator needs to be able to release blocks (and issue
a blkdev discard request) when the transaction which freed those
blocks is committed. Previously this was done via a polling mechanism
when blocks are allocated or freed. A much better way of doing things
is to create a jbd2 callback function and attaching the list of blocks
to be freed directly to the transaction structure.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
There are some newlines missing in ext4_check_descriptors, which
cause the printk level to be printed out when the next printk call
is made:
[ 778.847265] EXT4-fs: ext4_check_descriptors: Block bitmap for group 0
not in group (block 1509949442)!<3>EXT4-fs: group descriptors corrupted!
[ 802.646630] EXT4-fs: ext4_check_descriptors: Inode bitmap for group 0
not in group (block 9043971)!<3>EXT4-fs: group descriptors corrupted!
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
* git://git.linux-nfs.org/projects/trondmy/nfs-2.6: (53 commits)
NFS: Fix a resolution problem with nfs_inode->cache_change_attribute
NFS: Fix the resolution problem with nfs_inode_attrs_need_update()
NFS: Changes to inode->i_nlinks must set the NFS_INO_INVALID_ATTR flag
RPC/RDMA: ensure connection attempt is complete before signalling.
RPC/RDMA: correct the reconnect timer backoff
RPC/RDMA: optionally emit useful transport info upon connect/disconnect.
RPC/RDMA: reformat a debug printk to keep lines together.
RPC/RDMA: harden connection logic against missing/late rdma_cm upcalls.
RPC/RDMA: fix connect/reconnect resource leak.
RPC/RDMA: return a consistent error, when connect fails.
RPC/RDMA: adhere to protocol for unpadded client trailing write chunks.
RPC/RDMA: avoid an oops due to disconnect racing with async upcalls.
RPC/RDMA: maintain the RPC task bytes-sent statistic.
RPC/RDMA: suppress retransmit on RPC/RDMA clients.
RPC/RDMA: fix connection IRD/ORD setting
RPC/RDMA: support FRMR client memory registration.
RPC/RDMA: check selected memory registration mode at runtime.
RPC/RDMA: add data types and new FRMR memory registration enum.
RPC/RDMA: refactor the inline memory registration code.
NFS: fix nfs_parse_ip_address() corner case
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (46 commits)
UIO: Fix mapping of logical and virtual memory
UIO: add automata sercos3 pci card support
UIO: Change driver name of uio_pdrv
UIO: Add alignment warnings for uio-mem
Driver core: add bus_sort_breadthfirst() function
NET: convert the phy_device file to use bus_find_device_by_name
kobject: Cleanup kobject_rename and !CONFIG_SYSFS
kobject: Fix kobject_rename and !CONFIG_SYSFS
sysfs: Make dir and name args to sysfs_notify() const
platform: add new device registration helper
sysfs: use ilookup5() instead of ilookup5_nowait()
PNP: create device attributes via default device attributes
Driver core: make bus_find_device_by_name() more robust
usb: turn dev_warn+WARN_ON combos into dev_WARN
debug: use dev_WARN() rather than WARN_ON() in device_pm_add()
debug: Introduce a dev_WARN() function
sysfs: fix deadlock
device model: Do a quickcheck for driver binding before doing an expensive check
Driver core: Fix cleanup in device_create_vargs().
Driver core: Clarify device cleanup.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
module: remove CONFIG_KMOD in comment after #endif
remove CONFIG_KMOD from fs
remove CONFIG_KMOD from drivers
Manually fix conflict due to include cleanups in drivers/md/md.c
When cifs_demultiplex_thread was converted to a kthread based kernel
thread, great pains were taken to make it so that kthread_stop would be
used to bring it down. This just added unnecessary complexity since we
needed to use a signal anyway to break out of kernel_recvmsg.
Also, cifs_demultiplex_thread does a bit of cleanup as it's exiting, and
we need to be certain that this gets done. It's possible for a kthread
to exit before its main function is ever run if kthread_stop is called
soon after its creation. While I'm not sure that this is a real problem
with cifsd now, it could be at some point in the future if cifs_mount is
ever changed to bring down the thread quickly.
The upshot here is that using kthread_stop to bring down the thread just
adds extra complexity with no real benefit. This patch changes the code
to use the original method to bring down the thread, but still leaves it
so that the thread is actually started with kthread_run.
This seems to fix the deadlock caused by the reproducer in this bug
report:
https://bugzilla.samba.org/show_bug.cgi?id=5720
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Older samba server (eg. 3.0.24 from Debian etch) don't work correctly,
if DFS paths are used. Such server claim that they support DFS, but fail
to process some requests with DFS paths. Starting with Linux 2.6.26,
the cifs clients starts sending DFS paths in such situations, rendering
it unuseable with older samba servers.
The nodfs mount options forces a share to be used with non DFS paths,
even if the server claims, that it supports it.
Signed-off-by: Martin Koegler <mkoegler@auto.tuwien.ac.at>
Acked-by: Jeff Layton <jlayton@redhat.com>
Acked-by: Igor Mammedov <niallain@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
This patchs adds the CONFIG_AIO option which allows to remove support
for asynchronous I/O operations, that are not necessarly used by
applications, particularly on embedded devices. As this is a
size-reduction option, it depends on CONFIG_EMBEDDED. It allows to
save ~7 kilobytes of kernel code/data:
text data bss dec hex filename
1115067 119180 217088 1451335 162547 vmlinux
1108025 119048 217088 1444161 160941 vmlinux.new
-7042 -132 0 -7174 -1C06 +/-
This patch has been originally written by Matt Mackall
<mpm@selenic.com>, and is part of the Linux Tiny project.
[randy.dunlap@oracle.com: build fix]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Zach Brown <zach.brown@oracle.com>
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cannot assume writes will fully complete, so this conversion goes the easy
way and always brings the page uptodate before the write.
[dhowells@redhat.com: style tweaks]
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
de_thread() checks if the old leader was the ->child_reaper, this is not
possible any longer. With the previous patch ->group_leader itself will
change ->child_reaper on exit.
Henceforth find_new_reaper() is the only function (apart from
initialization) which plays with ->child_reaper.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move it into sysrq.c, along with the rest of the sysrq implementation.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We currently follow blindly what the partition table lies about the
disk, and let the kernel create block devices which can not be accessed.
Trying to identify the device leads to kernel logs full of:
sdb: rw=0, want=73392, limit=28800
attempt to access beyond end of device
Here is an example of a broken partition table, where sda2 starts
behind the end of the disk, and sdb3 is larger than the entire disk:
Disk /dev/sdb: 14 MB, 14745600 bytes
1 heads, 29 sectors/track, 993 cylinders, total 28800 sectors
Device Boot Start End Blocks Id System
/dev/sdb1 29 7800 3886 83 Linux
/dev/sdb2 37801 45601 3900+ 83 Linux
/dev/sdb3 15602 73402 28900+ 83 Linux
/dev/sdb4 23403 28796 2697 83 Linux
The kernel creates these completely invalid devices, which can not be
accessed, or may lead to other unpredictable failures:
grep . /sys/class/block/sdb*/{start,size}
/sys/class/block/sdb/size:28800
/sys/class/block/sdb1/start:29
/sys/class/block/sdb1/size:7772
/sys/class/block/sdb2/start:37801
/sys/class/block/sdb2/size:7801
/sys/class/block/sdb3/start:15602
/sys/class/block/sdb3/size:57801
/sys/class/block/sdb4/start:23403
/sys/class/block/sdb4/size:5394
With this patch, we ignore partitions which start behind the end of the disk,
and limit partitions to the end of the disk if they pretend to be larger:
grep . /sys/class/block/sdb*/{start,size}
/sys/class/block/sdb/size:28800
/sys/class/block/sdb1/start:29
/sys/class/block/sdb1/size:7772
/sys/class/block/sdb3/start:15602
/sys/class/block/sdb3/size:13198
/sys/class/block/sdb4/start:23403
/sys/class/block/sdb4/size:5394
These warnings are printed to the kernel log:
sdb: p2 ignored, start 37801 is behind the end of the disk
sdb: p3 size 57801 limited to end of disk
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I missed this when I did the arm26 removal.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
