This kills off the special Migo-R machvec, as nothing is using it. By
default this will switch to using the generic machvec, which provides the
same functionality. This saves us a bit of space in the machvec section.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
RSK+ platforms have quite a few characteristics in common, so roll them
together in to a shiny new RSK mach-type.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Move the not-so-generic pm code from arch/sh/kernel/pm.c to the
platform directory together with the rest of the hp6xx pm code.
This is done to let non-hp6xx platforms enable CONFIG_PM.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove out-of-date se7343 ioport code including some old support
for unknown-ne2000-pcmcia-card, cf-over-pcmcia and a mysterical
smc91x that once must have been on a special daughterboard.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add isp1161 platform data to get usb host working on se7343.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add 8250 platform data to setup the ST16C2550C chip on se7343.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix to make sure that the on-board interrupt sources are included
in the interrupt count on se7343.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for the RTE RSK+ 7201 board.
Signed-off-by: Peter Griffin <pgriffin@mpc-data.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock framework support to the lcdc driver and
adjust the board specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock framework support to the sh_mobile ceu and
adjust the board specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock framework support to the sh_mobile keysc driver and
adjust the board specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use a slower VIO_CKO clock frequency for the ov772x on Migo-R.
This improves the camera picture quality on Panel Board V2.1.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the ov772x byte sequence to enable byte swap. This to reflect
the recent CEU driver change to follow incoming byte order.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The sh7203.h include paths were missed in the previous update, so switch
the include path to cpu/ as with the rest.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Improve Migo-R ethernet performance by reducing smc91x overruns.
This is done by enabling SMC91X_NOWAIT and optimizing CS4 setup.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Renesas AP325RXA board has Epson RX-8564LC of RTC.
This patch supports RTC of this board.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch hooks up the magicpanelr2 board with the sh7720 pinmux code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Make the rsk7203 board use the newly added sh7203 pinmux code.
Only a single LED plus the serial console pins for now.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables the GPIO code on AP325RXA and converts the code from
register based pinmux configuration to GPIO based pin by pin setup.
While at it 2 LEDs and one switch are added and exported to user space.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables the GPIO code on Migo-R and converts the code from
register based pinmux configuration to GPIO based pin by pin setup.
Fix whitespace damage while at it and add 2 LEDs and export them to
user space.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This provides a workaround for users of sh_mobile_lcdcfb that don't
define HAVE_CLK and have otherwise sane clock initialization.
At the same time, move the sh_mobile_lcdc.h header to include/video/.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
AP320 and AP325RXA has CPLD data in NOR Flash.
If this area erased, this board can not boot.
This patch create CPLD data area and set writeable mask bit.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is 256K instead of 1M.
[ Converted to use asm/sizes.h. -- PFM ]
Signed-off-by: Luca Santini <luca.santini@spesonline.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the Renesas (RTE) EDOSK7760 board. Currently
supported devices are:
- ramdisk support
- ethernet support
- nfs support
- ext2/ext3 support
- i2c support
- fb support (M)
Signed-off-by: Luca Santini <luca.santini@spesonline.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Export the LCD panel size for sh_mobile_lcdc boards. This allows us
to perform dpi and screen aspect ratio calculations in user space.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH7763 has sh_eth device. This patch add sh_eth platform device
to this board.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch remove unneeded #include <linux/ide.h>'s.
It also adds a required #include <linux/interrupt.h> that was previously
implicitely pulled by ide.h
Signed-off-by: Adrian Bunk <bunk@kernel.org>
[bart: revert change to tests/lkdtm.c (spotted by Stephen Rothwell)]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Removed duplicated include <linux/irq.h> in
arch/sh/boards/mach-se/7343/irq.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Removed duplicated include <linux/delay.h> in
arch/sh/boards/board-ap325rxa.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The following build error was caused by an obvious typo:
<-- snip -->
...
LD arch/sh/mm/built-in.o
make[2]: *** No rule to make target `arch/sh/boards/board-shmin..o', needed by `arch/sh/boards/built-in.o'. Stop.
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix recently introduced I2C build breakage on AP325RXA and Migo-R.
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This flattens out the board directories in to individual mach groups,
we will use this for getting rid of unneeded directories, simplifying
the build system, and becoming more coherent with the refactored
arch/sh/include topology.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When I compiled Solution Engine, this become compile error
because plaform device of sh_eth device becomes enable.
When sh7710/sh7712 which could use sh_eth was chosen,
revised it so that platform device of sh_eth device became enable.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
