* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Remove __ARCH_WANT_INTERRUPTS_ON_CTXSW usage
microblaze: Use delay slot in __strnlen_user, __strncpy_user
microblaze: Remove NET_IP_ALIGN from system.h
microblaze: Add __ucmpdi2() helper function
microblaze: Raise SIGFPE/FPE_INTDIV for div by zero
microblaze: Switch ELF_ARCH code to 189
microblaze: Added DMA sync operations
microblaze: Moved __dma_sync() to dma-mapping.h
microblaze: Add PVR for Microblaze v8.20.a
microblaze: Fix access_ok macro
microblaze: Add loop unrolling for PAGE in copy_tofrom_user
microblaze: Simplify logic for unaligned byte copying
microblaze: Change label names - copy_tofrom_user
microblaze: Separate fixup section definition
microblaze: Change label name in copy_tofrom_user
microblaze: Clear top bit from cnt32_to_63
As far as I can tell the only reason microblaze has
__ARCH_WANT_INTERRUPTS_ON_CTXSW is because it initializes new task state
with interrupts enabled so that on switch_to() interrupts get enabled.
So change copy_thread() to clear MSR_IE instead of set it, this will
ensure switch_to() will always keep IRQs disabled.
The scheduler will disable IRQs when taking rq->lock in schedule() and
enable IRQs in finish_lock_switch() after its done its magic.
This leaves ARM the only __ARCH_WANT_INTERRUPTS_ON_CTXSW user.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Switch arch code to 189, the registered code in the upstream
version of binutils. Continue to accept the experimental 0xbaab.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
__dma_sync_page() was replaced by __dma_sync(), and parameters of calls to
the new function were adjusted to match __dma_sync()'s format.
Signed-off-by: Eli Billauer <eli.billauer@gmail.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
There is the problem with bit OR (|) because for
some combination is addr | size | addr+size equal
to seq.
For standard kernel setting (kernel starts at 0xC0000000)
is seq for user space 0xBFFFFFFF and everything below
this limit is fine.
But even address 0xBFFFFFFF is fine because it
is below kernel space.
Signed-off-by: Andrew Fedonczuk <andrew.fedonczuk@ericsson.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
There are numerous broken references to Documentation files (in other
Documentation files, in comments, etc.). These broken references are
caused by typo's in the references, and by renames or removals of the
Documentation files. Some broken references are simply odd.
Fix these broken references, sometimes by dropping the irrelevant text
they were part of.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Do not show error message for 32 interrupt lines
Revert "microblaze: PCI fix typo fault in of_node pointer moving into pci_bus"
microblaze: PCI fix typo fault in of_node pointer moving into pci_bus
microblaze: Add support for early console on mdm
microblaze: Simplify early console binding from DT
microblaze: Get early printk console earlier
microblaze: Standardise cpuinfo output for cache policy
microblaze: Unprivileged stream instruction awareness
microblaze: trivial: Fix typo fault
microblaze: exec: Remove redundant set_fs(USER_DS)
microblaze: Remove duplicated prototype of start_thread()
microblaze: Fix unaligned value saving to the stack for system with MMU
microblaze/irqs: Do not trace arch_local_{*,irq_*} functions
* 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
ARM: Consolidate the clkdev header files
ARM: set vga memory base at run-time
ARM: convert PCI defines to variables
ARM: pci: make pcibios_assign_all_busses use pci_has_flag
ARM: remove unnecessary mach/hardware.h includes
pci: move microblaze and powerpc pci flag functions into asm-generic
powerpc: rename ppc_pci_*_flags to pci_*_flags
Fix up conflicts in arch/microblaze/include/asm/pci-bridge.h
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[ poleg@redhat.com: no need to declare show_regs() in ptrace.h, sched.h does this ]
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recognize early Linux console from chosen - linux,stdout-path
instead of detecting the first console with appropriate
compatible strings.
This patch solved the problem on system with multiple
consoles.
Signed-off-by: Michal Simek <monstr@monstr.eu>
1. Register early console as standard console
2. Enable CON_BOOT console flag to ensure auto-unregistering by the kernel
3. remap_early_printk function remap physical console baseaddr to virtual space
Usage specific function for console remap is done after memory initialization
with IRQ turn off that's why there is not necessary to protect it.
The reason for remapping is that the kernel use TLB 63 for 1:1 address mapping
to be able to use console in very early boot-up phase. But allocating one TLB
just for console caused performance degression that's why ioremaps create new
mapping and TLB 63 is automatically released and ready to use.
Signed-off-by: Michal Simek <monstr@monstr.eu>
CC: Russell King <linux@arm.linux.org.uk>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: Ingo Molnar <mingo@redhat.com>
CC: Alan Cox <alan@linux.intel.com>
CC: <linux-serial@vger.kernel.org>
CC: Arnd Bergmann <arnd@arndb.de>
Add cpuinfo support for the new MicroBlaze option permitting userspace
(unprivileged) access to the streaming instructions (FSL / AXI-stream).
Emit a noisy warning at bootup if this is enabled, because bad user code
can potentially lockup the CPU.
Signed-off-by: John A. Williams <john.williams@petalogix.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
The prototype for start_thread() is already present in the MMU/NOMMU
independent part of the file. Remove the duplicate.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Do not trace arch_local_save_flags(), arch_local_irq_*() and friends.
Although they are marked inline, gcc may still make a function out of
them and add it to the pool of functions that are traced by the function
tracer. This can cause undesirable results (kernel panic, triple faults,
etc).
Add the notrace notation to prevent them from ever being traced.
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Move separate microblaze and powerpc pci flag functions pci_set_flags,
pci_add_flags, and pci_has_flag into asm-generic/pci-bridge.h so other
archs can use them.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Michal Simek <monstr@monstr.eu>
The generic code always get the device-node in the right place now
so a single implementation will work for all archs
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
All archs do more or less the same thing now, move it into
a single generic place.
I chose pci.h rather than of_pci.h to avoid having to change
all call-sites to include the later.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The whole business with re-assigning all bus numbers, creating
an OF bus "map" etc... is ancient powermac stuff that you really
don't care about on microblaze.
Similarly pci_device_from_OF_node() is unused and by getting rid
of it we can get rid of a whole lot of code otherwise unused on
this architecture
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Michal Simek <monstr@monstr.eu>
powerpc has two different ways of matching PCI devices to their
corresponding OF node (if any) for historical reasons. The ppc64 one
does a scan looking for matching bus/dev/fn, while the ppc32 one does a
scan looking only for matching dev/fn on each level in order to be
agnostic to busses being renumbered (which Linux does on some
platforms).
This removes both and instead moves the matching code to the PCI core
itself. It's the most logical place to do it: when a pci_dev is created,
we know the parent and thus can do a single level scan for the matching
device_node (if any).
The benefit is that all archs now get the matching for free. There's one
hook the arch might want to provide to match a PHB bus to its device
node. A default weak implementation is provided that looks for the
parent device device node, but it's not entirely reliable on powerpc for
various reasons so powerpc provides its own.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
32bit and 64bit on x86 are tested and working. The rest I have looked
at closely and I can't find any problems.
setns is an easy system call to wire up. It just takes two ints so I
don't expect any weird architecture porting problems.
While doing this I have noticed that we have some architectures that are
very slow to get new system calls. cris seems to be the slowest where
the last system calls wired up were preadv and pwritev. avr32 is weird
in that recvmmsg was wired up but never declared in unistd.h. frv is
behind with perf_event_open being the last syscall wired up. On h8300
the last system call wired up was epoll_wait. On m32r the last system
call wired up was fallocate. mn10300 has recvmmsg as the last system
call wired up. The rest seem to at least have syncfs wired up which was
new in the 2.6.39.
v2: Most of the architecture support added by Daniel Lezcano <dlezcano@fr.ibm.com>
v3: ported to v2.6.36-rc4 by: Eric W. Biederman <ebiederm@xmission.com>
v4: Moved wiring up of the system call to another patch
v5: ported to v2.6.39-rc6
v6: rebased onto parisc-next and net-next to avoid syscall conflicts.
v7: ported to Linus's latest post 2.6.39 tree.
> arch/blackfin/include/asm/unistd.h | 3 ++-
> arch/blackfin/mach-common/entry.S | 1 +
Acked-by: Mike Frysinger <vapier@gentoo.org>
Oh - ia64 wiring looks good.
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (27 commits)
x86: Clean up apic.c and apic.h
x86: Remove superflous goal definition of tsc_sync
x86: dt: Correct local apic documentation in device tree bindings
x86: dt: Cleanup local apic setup
x86: dt: Fix OLPC=y/INTEL_CE=n build
rtc: cmos: Add OF bindings
x86: ce4100: Use OF to setup devices
x86: ioapic: Add OF bindings for IO_APIC
x86: dtb: Add generic bus probe
x86: dtb: Add support for PCI devices backed by dtb nodes
x86: dtb: Add device tree support for HPET
x86: dtb: Add early parsing of IO_APIC
x86: dtb: Add irq domain abstraction
x86: dtb: Add a device tree for CE4100
x86: Add device tree support
x86: e820: Remove conditional early mapping in parse_e820_ext
x86: OLPC: Make OLPC=n build again
x86: OLPC: Remove extra OLPC_OPENFIRMWARE_DT indirection
x86: OLPC: Cleanup config maze completely
x86: OLPC: Hide OLPC_OPENFIRMWARE config switch
...
Fix up conflicts in arch/x86/platform/ce4100/ce4100.c
Change futex_atomic_op_inuser and futex_atomic_cmpxchg_inatomic
prototypes to use u32 types for the futex as this is the data type the
futex core code uses all over the place.
Signed-off-by: Michel Lespinasse <walken@google.com>
Cc: Darren Hart <darren@dvhart.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <20110311025058.GD26122@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The cmpxchg_futex_value_locked API was funny in that it returned either
the original, user-exposed futex value OR an error code such as -EFAULT.
This was confusing at best, and could be a source of livelocks in places
that retry the cmpxchg_futex_value_locked after trying to fix the issue
by running fault_in_user_writeable().
This change makes the cmpxchg_futex_value_locked API more similar to the
get_futex_value_locked one, returning an error code and updating the
original value through a reference argument.
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com> [tile]
Acked-by: Tony Luck <tony.luck@intel.com> [ia64]
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michal Simek <monstr@monstr.eu> [microblaze]
Acked-by: David Howells <dhowells@redhat.com> [frv]
Cc: Darren Hart <darren@dvhart.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <20110311024851.GC26122@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove compilation failure when ftrace in enabled.
Error log:
CC kernel/trace/power-traces.o
In file included from arch/microblaze/include/asm/irq.h:15,
from include/linux/irq.h:27,
from include/asm-generic/hardirq.h:12,
from arch/microblaze/include/asm/hardirq.h:15,
from include/linux/hardirq.h:7,
from include/linux/ftrace_event.h:7,
from include/trace/ftrace.h:19,
from include/trace/define_trace.h:96,
from include/trace/events/power.h:240,
from kernel/trace/power-traces.c:14:
include/linux/interrupt.h: In function '__raise_softirq_irqoff':
include/linux/interrupt.h:413: error: implicit declaration of function 'trace_softirq_raise'
In file included from include/trace/ftrace.h:554,
from include/trace/define_trace.h:96,
from include/trace/events/power.h:240,
from kernel/trace/power-traces.c:14:
include/trace/events/irq.h: In function 'ftrace_test_probe_irq_handler_entry':
include/trace/events/irq.h:37: error: implicit declaration of function 'check_trace_callback_type_irq_handler_entry'
include/trace/events/irq.h: In function 'ftrace_test_probe_irq_handler_exit':
include/trace/events/irq.h:67: error: implicit declaration of function 'check_trace_callback_type_irq_handler_exit'
include/trace/events/irq.h: In function 'ftrace_test_probe_softirq_entry':
include/trace/events/irq.h:112: error: implicit declaration of function 'check_trace_callback_type_softirq_entry'
include/trace/events/irq.h: In function 'ftrace_test_probe_softirq_exit':
include/trace/events/irq.h:126: error: implicit declaration of function 'check_trace_callback_type_softirq_exit'
include/trace/events/irq.h: In function 'ftrace_test_probe_softirq_raise':
include/trace/events/irq.h:140: error: implicit declaration of function 'check_trace_callback_type_softirq_raise'
make[5]: *** [kernel/trace/power-traces.o] Error 1
make[4]: *** [kernel/trace] Error 2
make[3]: *** [kernel] Error 2
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Michal Simek <monstr@monstr.eu>
A userland read of more than PAGE_SIZE bytes from /dev/zero results in
(a) not all of the bytes returned being zero, and
(b) memory corruption due to zeroing of bytes beyond the user buffer.
This is caused by improper constraints on the assembly __clear_user function.
The constrints don't indicate to the compiler that the pointer argument is
modified. Since the function is inline, this results in double-incrementing
of the pointer when __clear_user() is invoked through a multi-page read() of
/dev/zero.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Acked-by: Michal Simek <monstr@monstr.eu>
CC: stable@kernel.org
Warning log:
CHECK arch/microblaze/mm/fault.c
arch/microblaze/mm/fault.c:51:6: warning: incorrect type in initializer (different address spaces)
arch/microblaze/mm/fault.c:51:6: expected unknown type 2const [noderef] *__gu_addr<asn:1>
arch/microblaze/mm/fault.c:51:6: got unsigned int *<noident>
arch/microblaze/mm/fault.c:68:6: warning: symbol 'bad_page_fault' was not declared. Should it be static?
Signed-off-by: Michal Simek <monstr@monstr.eu>
Warning log:
CHECK arch/microblaze/kernel/sys_microblaze.c
arch/microblaze/kernel/sys_microblaze.c:37:17: warning: symbol 'microblaze_vfork' was not declared. Should it be static?
arch/microblaze/kernel/sys_microblaze.c:43:17: warning: symbol 'microblaze_clone' was not declared. Should it be static?
arch/microblaze/kernel/sys_microblaze.c:50:17: warning: symbol 'microblaze_execve' was not declared. Should it be static?
Signed-off-by: Michal Simek <monstr@monstr.eu>
Warning log:
CHECK arch/microblaze/kernel/cpu/cpuinfo-static.c
arch/microblaze/include/asm/cpuinfo.h:101:21: warning: incorrect type in argument 1 (different signedness)
arch/microblaze/include/asm/cpuinfo.h:101:21: expected unsigned int const [usertype] *p
arch/microblaze/include/asm/cpuinfo.h:101:21: got int *[assigned] val
...
Signed-off-by: Michal Simek <monstr@monstr.eu>
Warning in dma.c was caused by incorrect type in consistent_alloc function.
Warning log:
CHECK arch/microblaze/kernel/dma.c
arch/microblaze/kernel/dma.c:53:26: warning: incorrect type in argument 1 (different base types)
arch/microblaze/kernel/dma.c:53:26: expected int [signed] gfp
arch/microblaze/kernel/dma.c:53:26: got restricted unsigned int [usertype] flag
Signed-off-by: Michal Simek <monstr@monstr.eu>
Warning log:
CHECK arch/microblaze/kernel/ptrace.c
arch/microblaze/kernel/ptrace.c:126:11: warning: incorrect type in initializer (different address spaces)
arch/microblaze/kernel/ptrace.c:126:11: expected unknown type 2[noderef] *__pu_addr<asn:1>
arch/microblaze/kernel/ptrace.c:126:11: got unsigned long *<noident>
arch/microblaze/kernel/ptrace.c:134:17: warning: symbol 'do_syscall_trace_enter' was not declared. Should it be static?
arch/microblaze/kernel/ptrace.c:157:17: warning: symbol 'do_syscall_trace_leave' was not declared. Should it be static?
Signed-off-by: Michal Simek <monstr@monstr.eu>
Function sw_exception is linked with asm code.
Warning log:
CHECK arch/microblaze/kernel/exceptions.c
arch/microblaze/kernel/exceptions.c:53:6: warning: symbol 'sw_exception' was not declared. Should it be static?
Signed-off-by: Michal Simek <monstr@monstr.eu>
Used the same solution as SH. Changed len to PAGE_SIZE
in copy_to_user_page macro.
Implement flush_cache_page macro.
Signed-off-by: Michal Simek <monstr@monstr.eu>
r0_ram pool was used for saving/restoring register
content if hw exception happen. This poll was replaced by
pt_pool_space with PT_SIZE size.
Based on this change SAVE_STATE_ARG_SPACE was removed which
caused that PTO offset is zero that's why is also removed.
r0_ram space was used as scratchpad by v850. In early
Microblaze Linux developing phase was this part of code
blindly copied.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Reason: Import mainline device tree changes on which further patches
depend on or conflict.
Trivial conflict in: drivers/spi/pxa2xx_spi_pci.c
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Do not disable irq in asm but use irq macros.
Systems with MSR=0 couldn't use pte_update function
because msrclr was hardcoded.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Patch: Fix IRQ flag handling naming
(sha1: f9ee29270c11dba7d0fe0b83ce47a4d8e8d2101)
introduced problem on system with MSR=0.
Signed-off-by: Michal Simek <monstr@monstr.eu>
There is a tiny difference between PPC32 and PPC64. Microblaze uses the
PPC32 variant.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
[grant.likely@secretlab.ca: Added comment to #endif, moved documentation
block to function implementation, fixed for non ppc and microblaze
compiles]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Function ptep_test_and_clear_young have had wrong the first argument.
It is also necessary to add __HAVE macros for ptep_test_and_clear_young and
ptep_get_and_clear functions.
Error log:
In file included from linux/arch/microblaze/include/asm/pgtable.h:570,
from arch/microblaze/mm/pgtable.c:35:
include/asm-generic/pgtable.h:23: error: conflicting types for 'ptep_test_and_clear_young'
linux/arch/microblaze/include/asm/pgtable.h:449: error:
previous definition of 'ptep_test_and_clear_young' was here
include/asm-generic/pgtable.h:73: error: redefinition of 'ptep_get_and_clear'
linux/arch/microblaze/include/asm/pgtable.h:462: error:
previous definition of 'ptep_get_and_clear' was here
Signed-off-by: Michal Simek <monstr@monstr.eu>
Add missing linux/pagemap.h to solve compilation error.
Error log:
In file included from linux/arch/microblaze/include/asm/tlb.h:17,
from mm/pgtable-generic.c:9:
include/asm-generic/tlb.h: In function 'tlb_flush_mmu':
include/asm-generic/tlb.h:76: error: implicit declaration of function 'release_pages'
include/asm-generic/tlb.h: In function 'tlb_remove_page':
include/asm-generic/tlb.h:105: error: implicit declaration of function 'page_cache_release'
Signed-off-by: Michal Simek <monstr@monstr.eu>
