All current Blackfin parts are using RTL v1.9, but they don't expose the
hardware registers to probe this dynamically. So hardcode the version to
v1.9 for now.
Need to move the local hwvers related defines higher up in the header so
that sub-musb headers may utilize them.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
we have those addresses already ioremaped, so let's
use our __raw_readl/writel wrappers.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adding support for MUSB register save and restore during system
suspend and resume.
Changes:
- Added musb_save/restore_context() functions
- Added platform specific musb_platform_save/restore_context()
to handle platform specific jobs.
- Maintaining BlackFin compatibility by adding read/write
functions for registers which are not available in BlackFin
Tested system suspend and resume on OMAP3EVM board.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Save dynamic FIFO read only information for later uses during
musb_save/restore_context functions.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MUSB: save hardware revision at init
This can be used later to flag workarounds for issues affecting
particular revisions. Saving this at init avoids having to
read the HWVERS register multiple times in code.
While at it, use macros to extract the version information
instead of using hardcoded values.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Blackfin port doesn't support HAVE_CLK and the musb driver works fine
with support stubbed out, so take the existing Blackfin clk stubs and move
them to common musb code so we can drop the Kconfig dependency.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested on OMAP3 host side with Creative (Live! Cam Optia) USB camera
which uses high bandwidth isochronous IN endpoints. FIFO mode 4 is
updated to provide the needed 4K endpoint buffer without breaking
the g_nokia composite gadget configuration. (This is the only
gadget driver known to use enough endpoints to notice the change.)
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Minor cleanup of OTG timer handling:
* unify decls for OTG time constants, in the core header
* set up and use that timer in a more normal way
* move to the driver struct, so it's usable outside core
And tighten use and setup of T(a_wait_bcon) so that if it's used,
it's always valid. (If that timer expires, the A-device will
stop powering VBUS. For non-OTG systems, that will be a surprise.)
No behavioral changes, other than more consistency when applying
that core HNP timeout.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Let the otg_transceiver in MUSB be managed by an external driver;
don't assume it's integrated. OMAP3 chips need it to be external,
and there may be ways to interact with the transceiver which add
functionality to the system.
Platform init code is responsible for setting up the transeciver,
probably using the NOP transceiver for integrated transceivers.
External ones will use whatever the board init code provided,
such as twl4030 or something more hands-off.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The gadget EP0 code routinely ignores an interrupt at end of
the data phase because of musb_g_ep0_giveback() resetting the
state machine to "idle, waiting for SETUP" phase prematurely.
The driver also prematurely leaves the status phase on
receiving the SetupEnd interrupt.
As there were still unhandled endpoint 0 interrupts happening
from time to time after fixing these issues, there turned to
be yet another culprit: two distinct gadget states collapsed
into one.
The (missing) state that comes after STATUS IN/OUT states was
typically indiscernible from them since the corresponding
interrupts tend to happen within too little period of time
(due to only a zero-length status packet in between) and so
they got coalesced; yet this state is not the same as the next
one which is associated with the reception of a SETUP packet.
Adding this extra state seems to have fixed the rest of the
unhandled interrupts that generic_interrupt() and
davinci_interrupt() hid by faking their result and only
emitting a debug message -- so, stop doing that.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Correct musb_read_fifosize() and musb_configure_ep0() functions
for the #ifndef BLACKFIN branch when the silicon uses static FIFO
configuration. (Most current silicon configures this controller
to use dynamic FIFO configuration; some parts from ST don't, like
the STM STA2062.)
Signed-off-by: Giuseppe GORGOGLIONE <giuseppe.gorgoglione@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current MUSB host code doesn't make use of all the available
FIFOs in for periodic transfers since it wrongly assumes the RX
and TX sides of any given hw_ep always share one FIFO.
Change: use 'in_qh' and 'out_qh' fields of the 'struct musb_hw_ep'
to check the endpoint's business; get rid of the now-unused 'periodic'
array in the 'struct musb'. Also optimize a loop induction variable
in the endpoint lookup code.
(Based on a previous patch from Ajay Kumar Gupta <ajay.gupta@ti.com>)
[ dbrownell@users.sourceforge.net: clarify description and origin
of this fix; whitespace ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some config registers are not avaiable in Blackfin, we have to comment them out.
v1-v2:
- remove Blackfin specific header file
- add Blackfin register version to musb_regs.h header file
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Without it, in platforms that don't provide irq_chip.set_wake(),
like omap, musb will WARN() on driver removal.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix three omissions in the "mode" sysfs attribute support:
(a) inability to report errors;
(b) no DaVinci support ... just report an error;
(c) for omap2430, accepting unsupportable values
The 2430 stuff is still odd....
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drivers should not add procfs. The functionality in the old
procfs file will be moved to debugfs.
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use platform_data to pass musb configuration-specific
details to musb driver.
This patch will prevent that other platforms selecting
HAVE_CLK and enabling musb won't break tree building.
The other parts of it will come when linux-omap merge
up more omap2/3 board-files.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for MUSB and TUSB controllers
integrated into omap2430 and davinci. It also adds support
for external tusb6010 controller.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
