Sometimes boards don't reset properly, and the address read out of the
EEPROM is zero. Stop the insanity before the device gets registered.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The transmit side code has a number of ring problems that caused some
of the Bugzilla reports. Rather than trying to fix the details, it is safer
to rewrite the code that handles transmit completion and freeing.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Consolidate all usage of ring low water mark to one value.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since accessing the PHY can take 100's of usecs, use a work queue to
allow spinning in outside of soft/hard irq.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The following patch updates the myri10ge to 1.0.0, with the following changes:
* Switch to dma_alloc_coherent API.
* Avoid PCI burst when writing the firmware on chipset with unaligned completions.
* Use ethtool_op_set_tx_hw_csum instead of ethtool_op_set_tx_csum.
* Include linux/dma-mapping.h to bring DMA_32/64BIT_MASK on all architectures
(was missing at least on alpha).
* Some typo and warning fixes.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew J. Gallatin <gallatin@myri.com>
drivers/net/myri10ge/myri10ge.c | 57 +++++++++++++++++++-----------
1 file changed, 37 insertions(+), 20 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Various PCI bus errors can be signaled by newer PCI controllers.
This patch adds the PCI error recovery callbacks to the intel gigabit
ethernet e1000 device driver. The patch has been tested, and appears
to work well.
Signed-off-by: Linas Vepstas <linas@linas.org>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Various PCI bus errors can be signaled by newer PCI controllers. This
patch adds the PCI error recovery callbacks to the intel ethernet e100
device driver. The patch has been tested, and appears to work well.
Signed-off-by: Linas Vepstas <linas@linas.org>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
It was brought to our attention that the prefetches break e1000 traffic
on xscale/arm architectures. Remove them for now. We'll let them
stay in mm for a while, or find a better solution to enable.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
New code added in 2.6.17 caused setup_irq to print a warning when
running ethtool -t eth0 offline.
This test marks the request_irq call made by this test as a "probe"
to see if the interrupt is shared or not.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
skb_clone() may fail, we should check the result.
Coverity CID: 1215.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Matt Mackall <mpm@selenic.com>
netconsole is being wrong here. If it wasn't enabled there's no error.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
zd1201 is wifi adapter, yet it is hiding in drivers/usb/net where
noone can find it. This moves Kconfig/Makefile zd1201 to the right
place.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The debug logging in bcm43xx_ieee80211_set_security() is pretty noisy.
Make it more silent.
Signed-off-by: Jason Lunz <lunz@falooley.org>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
From: Florin Malita <fmalita@gmail.com>
The skb may be gone after netif_rx(), we can't use 'skb->len' to update the
stats. 'pkt_len' should work instead.
Coverity CID: 911.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Also add the Poll RX DMA Memory workaround to the DMA4
(xmitstatus) path.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hi,
This patch add new PCI ID for r8169 driver.
RTL8110SBL has this PCI ID.
Please aply.
Yoichi
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds flow control support for tx and rx pause frames in
forcedeth.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The original patch was using whitespaces instead of tabs.
Signed-off-by: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
During a code scan for another change I discovered that this call to
pcnet32_free_ring must be removed. If the open fails due to a lack of
memory all the ring structures are removed via the call to free_ring
and a subsequent call to open will dereference a null pointer in
pcnet32_init_ring.
Please apply to 2.6.17.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Someone was waaay too aggressive and removed e1000's reboot notifier
instead of porting it to the new way of the shutdown handler. This change
broke wake on lan. Add the shutdown handler back in using the same method
as e100 uses.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
(cherry picked from c653e6351e commit)
Fix section mismatch warnings:
WARNING: drivers/net/wireless/arlan.o - Section mismatch: reference to
.init.text:arlan_probe from .text between 'init_module' (at offset
0x3526) and 'cleanup_module'
WARNING: drivers/net/wireless/arlan.o - Section mismatch: reference to
.init.text:init_arlan_proc from .text between 'init_module' (at offset
0x3539) and 'cleanup_module'
WARNING: drivers/net/wireless/arlan.o - Section mismatch: reference to
.exit.text:cleanup_arlan_proc from .text between 'cleanup_module' (at
offset 0x356c) and 'arlan_diagnostic_info_string'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix section mismatch warning:
WARNING: drivers/net/wireless/wavelan.o - Section mismatch: reference to
.init.text: from .text between 'init_module' (at offset 0x371e) and
'cleanup_module'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
increase the year dates to 2006 and bump the version to 1.0.109-k2
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
same as e1000 - remove the changelog from the driver code itself.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
deinline a few large functions as to allow the compiler to pick.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
This mimics a change made in the e1000 driver that imitates a slick
tg3 way of avoiding grabbing the lock around restarting the tx queue.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
There seemed to be another bug introduced as well as a performance hit
with the addtion of the sentinel descriptor workaround. Removal of
this workaround appears to prevent the hang. We'll take a risk
and remove it, as we had never seen the originally reported bug
under linux.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
user contributed fix for LAA across down/up, from tonychung00@users.sf.net.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Moved interrupt masking to before requesting the interrupt from the OS.
Moved interrupt enable to after netif_poll_enable. This fixes a racy
BUG() where polling would be running on another CPU at the same time
that netif_poll_enable would run.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
If a SIR dongle is built in the kernel while IRTTY_SIR is built
as a module, kernel compilation will fail.
Thus, the SIR dongle config should depend on the IRTTY_SIR.
Closes kernel bug# 6512
(http://bugzilla.kernel.org/show_bug.cgi?id=6512)
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
o modify the rx refill logic and tail bump
o add counter for failures
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
new SMSC LAN83C185 10BaseT/100BaseTX PHY driver for the PHY subsystem
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch provides a sysfs interface to change some properties of the
ibmveth buffer pools (size of the buffers, number of buffers per pool,
and whether a pool is active). Ethernet drivers use ethtool to provide
this type of functionality. However, the buffers in the ibmveth driver
can have an arbitrary size (not only regular, mini, and jumbo which are
the only sizes that ethtool can change), and also ibmveth can have an
arbitrary number of buffer pools
Under heavy load we have seen dropped packets which obviously kills TCP
performance. We have created several fixes that mitigate this issue,
but we definitely need a way of changing the number of buffers for an
adapter dynamically. Also, changing the size of the buffers allows
users to change the MTU to something big (bigger than a jumbo frame)
greatly improving performance on partition to partition transfers.
The patch creates directories pool1...pool4 in the device directory in
sysfs, each with files: num, size, and active (which default to the
values in the mainline version).
Comments and suggestions are welcome...
--
Santiago A. Leon
Power Linux Development
IBM Linux Technology Center
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On Mon, May 15, 2006 at 12:56:37AM -0700, Andrew Morton wrote:
>...
> Changes since 2.6.17-rc3-mm1:
>...
> git-netdev-all.patch
>...
> git trees
>...
This patch makes the needlessly global bus_speed[] static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The truncate threshold calculation to prevent receiver from getting stuck
was incorrect, and it didn't take into account the upper limit on bits
in the register so the jumbo packet support was broken.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Someone was waaay too aggressive and removed e1000's reboot notifier
instead of porting it to the new way of the shutdown handler. This change
broke wake on lan. Add the shutdown handler back in using the same method
as e100 uses.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
If the skb allocation fails, the current error path calls
dev_kfree_skb_irq() with a NULL argument. Also, 'err' is not being used.
Coverity CID: 275.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Increment the driver version to 1.0.104-k2
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
This adds a TX timeout counter to the ethtool stats, a tx timeout
debug message, and sets the timer to 5 seconds.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Use DPRINTK and msglvl, and ethtool to control it. Add proper names
to netdev structs and mappings.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
This adds a define for an awkward and uncommented value.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Add support for Copper 10GbE device ID 109E
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Make default flow control only have *sending* of flow control packets
enabled, and fix to disable / enable flow control correctly. Set flow
control defaults to disable receiving flow control from the link
partner, to fix the transmit fifo overlow errata
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Fix rare early completion when using TSO. This essentially is the
e1000 fix, with code that was mostly already written. Another skb frag
was also needed.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Use kmalloc() instead of a local array in bnx2_nvram_write().
Update version to 1.4.40.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug in bnx2_nvram_write() caused by a counter variable not
correctly incremented by 4.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some missing rx error counters for 5705 and newer chips.
Update version to 3.58.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the skb allocation fails, the current error path calls
dev_kfree_skb_irq() with a NULL argument. Also, 'err' is not being used.
Coverity CID: 275.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With Manfred Spraul <manfred@colorfullife.com> and
Andrew Morton <akpm@osdl.org>
Bring back this recently-reverted patch, only fixed.
Original changelog:
From: Ayaz Abdulla <aabdulla@nvidia.com>
This patch fixes the issues with multiple irqs.
I am resending based on feedback. I decoupled the dma mask for
consistent memory and fixed leak with multiple irq in error path.
Thanks to Manfred for catching the spin lock problem.
Fix it:
From: Manfred Spraul <manfred@colorfullife.com>
Fix bug introduced by ebf34c9b6f, covered in
http://bugzilla.kernel.org/show_bug.cgi?id=6568.
Remove second instance of the request_irq() calls: they were moved
from nv_open into nv_request_irq.
Thanks to Alistair Strachan <alistair@devzero.co.uk> for reporting and
persisting.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Call pci_map_single() with the actual size of the receive
buffers, not 0 (which skb->len is initialized to by dev_alloc_skb()).
Signed-off-by: Erling A. Jacobsen <linuxcub@email.dk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver will get stuck (permanent transmit timeout), if the transmit
ring size is set too small. It needs to have enough ring elements to
hold one maximum size transmit.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Skge driver always causes bad checksums on big-endian.
The checksum in the receive control block was being swapped
when it doesn't need to be.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If the status ring processing can't keep up with the incoming frames,
it is more efficient to have NAPI keep scheduling the poll routine
rather than causing another interrupt.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Logic error in the phy initialization code. Also, turn on wake on lan
bit in status control.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Dlink DGE-560T uses Yukon2 chipset so it needs sky2 driver; and
the DGE-530T uses Yukon1 so it uses skge driver.
Bug: http://bugzilla.kernel.org/show_bug.cgi?id=6544
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If both ports are receiving on the SysKonnect dual port cards,
then it appears the bus interface unit can give an interrupt status
for frame before DMA has completed. This leads to bogus frames
and general confusion. This is why receive checksumming is also
messed up on dual port cards.
A workaround for the out of order receive problem is to eliminating
split transactions on PCI-X.
This version is based of the current linux-2.6.git including earlier
patch to disable dual ports.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Revert previous patch with subject "change mdelay to msleep and remove
from ISR path". This patch seems to have caused bigger problems than
it solved, and it didn't solve much of a problem to begin with...
Discussion about backing-out this patch can be found here:
http://marc.theaimsgroup.com/?l=linux-netdev&m=114321570402396&w=2
The git commit associated w/ the original patch is:
6ba98d311d
Signed-off-by: John W. Linville <linville@tuxdriver.com
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Revert ebf34c9b6f. Maybe. Due to crashes
at shutdown - see http://bugzilla.kernel.org/show_bug.cgi?id=6568.
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make the device-tree information more generic and more
like the pSeries virtual lan device. Also use the MAC
address from the device tree.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/shemminger/netdev-2.6:
sky2: prevent dual port receiver problems
x86_64: Check for bad dma address in b44 1GB DMA workaround
The ixp2000 driver for the enp2611 was developed on a board with
There's a bunch of unused exports in the wireless drivers; that's
bad since unused exports take up quite a bit of space in total;
the patch below removes them.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I still need this hack to work around the fact that softmac doesn't
attempt to associate when we bring the device up...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Needed for interaction with the nommu code in x86-64 which
will return bad_dma_address if the address exceeds dma_mask.
Cc: netdev@vger.kernel.org
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When both ports are receiving simultaneously, the receive logic gets confused
and may pass up a packet before it is full. This causes hangs, and IP will see
lots of garbage packets. There is even the potential for data corruption if
a later arriving packet DMA's into freed memory.
It looks like a hardware bug because status arrives for a packet but no
data is there. Until this bug is worked out, block the user from bringing
up both ports at once.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Needed for interaction with the nommu code in x86-64 which
will return bad_dma_address if the address exceeds dma_mask.
Cc: netdev@vger.kernel.org
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
three gigabit ports, but some enp2611 models only have two ports
(and only one onboard PM3386.) The current driver assumes there
are always three ports and so it doesn't work on the two-port
version of the board at all.
This patch adds a bit of logic to the enp2611 driver to limit the
number of ports to 2 if the second PM3386 isn't detected.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
On alpha:
drivers/net/dl2k.c: In function `rio_free_tx':
drivers/net/dl2k.c:768: error: `DMA_48BIT_MASK' undeclared (first use in this function)
drivers/net/dl2k.c:768: error: (Each undeclared identifier is reported only once
drivers/net/dl2k.c:768: error: for each function it appears in.)
drivers/net/dl2k.c: In function `receive_packet':
drivers/net/dl2k.c:896: error: `DMA_48BIT_MASK' undeclared (first use in this function)
drivers/net/dl2k.c: In function `rio_close':
drivers/net/dl2k.c:1803: error: `DMA_48BIT_MASK' undeclared (first use in this function)
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Even with fiber cards ethtool reports that the connected port is TP,
the patch fix this.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NET_SCHED]: HFSC: fix thinko in hfsc_adjust_levels()
[IPV6]: skb leakage in inet6_csk_xmit
[BRIDGE]: Do sysfs registration inside rtnl.
[NET]: Do sysfs registration as part of register_netdevice.
[TG3]: Fix possible NULL deref in tg3_run_loopback().
[NET] linkwatch: Handle jiffies wrap-around
[IRDA]: Switching to a workqueue for the SIR work
[IRDA]: smsc-ircc: Minimal hotplug support.
[IRDA]: Removing unused EXPORT_SYMBOLs
[IRDA]: New maintainer.
[NET]: Make netdev_chain a raw notifier.
[IPV4]: ip_options_fragment() has no effect on fragmentation
[NET]: Add missing operstates documentation.
661FX7MI-S motherboard which uses the SiS 661FX chipset. The patch adds
an entry to mii_chip_info for the transceiver.
The PHY ids were found using the sis900_c_122.diff patch from
http://brownhat.org/sis900.html but that patch didn't solve the problem,
because the PHY at address 1 was already being chosen.
Without my patch, when bursts of packets arrive from other hosts on a
LAN, the interface dropped one roughly 10% of the time, causing
retransmits. There were fifth second pauses in refresh of large xterms,
and it made Netrek suck. I can provide further test data.
Workaround in lieu of patch is to use mii-tool to advertise
100baseTx-HD, then force renegotiation.
I wasn't able to identify the actual transceiver, so the description
field is a guess.
This patch is similar to Artur Skawina's patch:
http://marc.theaimsgroup.com/?l=linux-netdev&m=114297516729079&w=2
I'm not sure, but I wonder if it means the default behaviour should be
changed, so as to better handle future transceivers.
Diff is against 2.6.16.13.
Signed-off-by: James Cameron <james.cameron@hp.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
make sure phy_map entries whose PHY address is masked are initialized
to NULL, given that other code (such as mdiobus_unregister for
instance) assumes that non-NULL phy_map entries are allocated
phy_devices
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Bringing down a port also masks off the status and other IRQ's
needed for device to function due to missing paren's.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
tg3_run_loopback doesn't check that dev_alloc_skb() returns anything
useful.
Even if dev_alloc_skb() fails to return an skb to us we'll happily go
on and assume it did, so we risk dereferencing a NULL pointer. Much
better to fail gracefully by returning -ENOMEM than crashing here.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since sir_kthread.c pretty much duplicates the workqueue
functionality, we'd better switch. The SIR fsm has been merged into
sir_dev.c and thus sir_kthread.c is deleted.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minimal PNP hotplug support for the smsc-ircc2 driver. A modular
driver will be modprobed via hotplug, but still bypasses driver model
probing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A newer board revision changed the type of ethernet phy.
Moreover, this generalizes the way that a phy gets switched
into fiber mode when autodetection is not available.
Signed-off-by: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
We found a new chip setting that we need in order
to make the driver work more reliable.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Ensure that 8-bit mode is selected for the on-board Realtek RTL8019AS chip
on Toshiba RBHMA4x00, get rid of the duplicate #ifdef's when setting
ei_status.word16.
The chip's datasheet says that the PSTOP register shouldn't exceed 0x60 in
8-bit mode -- ensure this too.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
since the au1000 driver already selects the CRC32 routines, simply replace
the internal ether_crc() implementation with the semantically equivalent
one from <linux/crc32.h>
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The newest Yukon Ultra chipset's require more special tweaks.
They seem to be like the Yukon XL chipsets. This code is transliterated
from the latest SysKonnect driver; I don't have any Ultra hardware.
Signed-off-by: Stephe Hemminger <shemminger@osdl.org>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
It is more efficient not to write the status ring from the
processor and just read the active portion.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Need to make the edge-triggered workaround timer faster to get marginally
better peformance. The test_and_set_bit in schedule_prep() acts as a barrier
already. Make it a module parameter so that laptops who are concerned
about power can set it to 0; and user's stuck with broken BIOS's
can turn the driver into pure polling.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Gcc isn't smart enough to know that it can do a modulo
operation with power of 2 constant by doing a mask.
So add macro to do it for us.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Mask for transmit ring status was picking up bits from the
unused sync ring. They were always zero, so far...
Also, make sure to remind self not to make tx ring too big.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The status interrupt flag should be cleared before processing,
not afterwards to avoid race. Need to process in poll routine
even if no new interrupt status. This is a normal occurrence when
more than 64 frames (NAPI weight) are processed in one poll routine.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
This is a backout of earlier patch.
The whole rescheduling hack was a bad idea. It doesn't really solve
the problem and it makes the code more complicated for no good reason.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Use NULL instead of 0 for a null pointer value (sparse warning):
drivers/net/irda/irda-usb.c:1781:30: warning: Using plain integer as NULL pointer
Also, correct timeout argument to use milliseconds instead of jiffies.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The resource data in the network device is intended for ISA and other
older busses, but not for PCI. Don't put PCI data there. Don't (ab)use
the network device for keeping the IRQ number.
Retire orinoco_pci_setup_netdev(), and print some minimal information to
the kernel log instead, identifying the network device and the driver
mostly to identify problems at startup. Scripts should rely on sysfs.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't use flags in the spinlocks - the PCMCIA resume functions may not
be called under lock. Don't ignore any errors.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Report only the first I/O window and IRQ, and also add the driver name.
The second I/O window, Vpp and configuration index are not interesting
to most users. They can be found by PCMCIA debug tools if needed.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware resources should not be made available to other devices while
the network device is still registered. Also remove the related debug
statements.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Running Linux 2.6.17-rc3-mm1 which has this patch included I get this
interesting message:
airo(eth0): WPA unsupported (only firmware versions 5.30.17 and greater
support WPA. Detected 5.30.17)
airo_test_wpa_capable assumes that the softSubVer part of the firmware
version number is coded in BCD. Apparently, that's not true.
I have firmware version 5.30.17 and cap_rid.softSubVer is 0x11==17.
Signed-off-by: Michal Schmidt <xschmi00@stud.feec.vutbr.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
