Implement reset / poweroff in the board code instead. The peripheral reset
code is gone too since YAMON which all in-tree boards use does the same
work when it boots.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/783/
Patchwork: http://patchwork.linux-mips.org/patch/882/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For 64-bit kernels with 64KB pages and two level page tables, there are
42 bits worth of virtual address space This is larger than the 40 bits of
virtual address space obtained with the default 4KB Page size and three
levels, so there are no draw backs for using two level tables with this
configuration.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/761/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the GPIO config symbol to only build Au1000 interrupt code on chips with
compatible hw.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/670/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the cpu subtype cpp macros in favor of runtime detection,
to improve compile coverage of the alchemy common code.
(Increases kernel size by 700 bytes).
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/699/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch makes the board code register the au1000-eth platform device. The
au1000-eth platform data can be overriden with the au1xxx_override_eth_cfg
function like it has to be done for the Bosporus board which uses a
different MAC/PHY setup.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: David Miller <davem@davemloft.net>
Cc: linux-mips@linux-mips.org
Cc: netdev@vger.kernel.org
Patchwork: http://patchwork.linux-mips.org/patch/618/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Machine driver for DB1200 AC97 and I2S audio systems, intended as a proper
reference asoc machine for Alchemy-based systems. AC97/I2S can be selected
at boot time by setting switch S6.7.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Cc: alsa-devel@alsa-project.org
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Create own directory for DB1200 code and update it with new features.
- SPI support:
- tmp121 temperature sensor
- SPI flash on DB1200
- I2C support
- NE1619 sensor
- AT24 eeprom
- I2C/SPI can be selected at boot time via switch S6.8
- Carddetect IRQs for SD cards.
- gen_nand based NAND support.
- hexleds count sleep/wake transitions.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace the devboard NOR MTD mapping driver with physmap-flash support.
Also honor the "swapboot" switch settings wrt. to the layout of the
NOR partitions.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Acked-By: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
UART autodetection breaks on the Au1300 but the IP blocks are identical,
at least according to the datasheets. Help the 8250 driver by passing
on uart type information via platform data.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Warnings being suppressed, we can now turn on -Werror for boards which did
not have it already (devboards and xss1500).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes warnings due to potentially unused
variables in board setup code or mixed variables
declaration and code (forbidden by ISO C90).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove unused uart bit definitions and base macros.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch replaces the general alchemy prom_putchar() implementation
in favor of board-specific versions: The UART where the output of
prom_putchar is directed to really depends on the board, the current
implementation hardcodes this on a per-SoC basis which is just wrong.
So a generic uart tx function is provided in the alchemy headers,
and the boards can provide their own prom_putchar with custom
destination uart, and all in-kernel alchemy boards support
early printk.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
DMA can only be done from physical addresses; move the "virt_to_phys"
source/destination buffer address translation from the dbdma queueing
functions (since the hardware can only DMA to/from physical addresses)
to their respective users.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove dbdma compat macros, move remaining users over to default
queueing functions and -flags.
(Queueing function signature has changed in order to give
a build failure instead of silent functional changes due
to the no longer implicitly specified DDMA_FLAGS_IE flag)
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
By replacing an extra do_IRQ with a goto, the assembly shrinks
from 260 to 212 bytes (gcc-4.3.4).
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Eliminate the sharing of IRQ names among the differenct Alchemy
variants. IRQ numbers need no longer be hidden behind a
CONFIG_SOC_AU1XXX symbol: step 1 in my quest to make the Alchemy
code less reliant on a hardcoded subtype.
This patch also renames the GPIO irq number constants. It's really
an interrupt line, NOT a GPIO number!
Code which relied on certain irq numbers to have the same name
across all supported cpu subtypes is changed to determine current
cpu subtype at runtime; in some places this isn't possible so
a "compat" symbol is used.
Run-tested on DB1200.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Raise RTCMATCH2 interrupt priority in case it is used as the system
timer tick.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Alchemy hardware provides a method to prioritize interrupts
on a controller by assigning them to a differenct core request line.
Assign usb device request interrupt to IC0 Request 0 (which has
highest priority in the core and the dispatcher) and others to
Request 1. The explicit check for usb device request occurrence
should be obsolete now.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Register the PCMCIA driver on all boards supported by it,
get rid of now-unused pcmcia macros in the board headers
(and subsequently empty pb1100/pb1500 ones).
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
New PCMCIA socket driver for all Db/Pb1xxx boards (except Pb1000),
which replaces au1000_db1x00.c and (most of) au1000_pb1x00.c.
Notable improvements:
- supports Db1000, DB/PB1100/1500/1550/1200.
- support for carddetect and statuschange IRQs.
- pcmcia socket mem/io/attr areas and irqs passed through
platform resource information.
- doesn't freeze system during card insertion/ejection like
the one it replaces.
- boardtype is automatically detected using BCSR ID register.
Run-tested on the DB1200.
Cc: Linux-PCMCIA <linux-pcmcia@lists.infradead.org>
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
remove board_init_irq(): On all in-kernel boards it is sufficient to
initialize board interrupts in an arch_initcall by using the default
linux irq functions.
Some small irqmap.c files have been folded into board_setup files.
Run-tested on DB1200; compile-tested on all other affected boards.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the PB1200 IRQ cascade code out to the BCSR support code:
upcoming DB1300 support can use it too.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All Alchemy development boards have external CPLDs with a few registers
in them. They all share an identical register layout with only a few
minor differences (except the PB1000) in bit functions and base
addresses.
This patch
- adds a primitive facility to initialize and use these external
registers,
- replaces all occurrences of bcsr->xxx accesses with calls to the new
functions (the pb1200 cascade irq handling code is special).
- collects BCSR register information scattered throughout the board
headers in a central place.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (48 commits)
x86/PCI: Prevent mmconfig memory corruption
ACPI: Use GPE reference counting to support shared GPEs
x86/PCI: use host bridge _CRS info by default on 2008 and newer machines
PCI: augment bus resource table with a list
PCI: add pci_bus_for_each_resource(), remove direct bus->resource[] refs
PCI: read bridge windows before filling in subtractive decode resources
PCI: split up pci_read_bridge_bases()
PCIe PME: use pci_pcie_cap()
PCI PM: Run-time callbacks for PCI bus type
PCIe PME: use pci_is_pcie()
PCI / ACPI / PM: Platform support for PCI PME wake-up
ACPI / ACPICA: Multiple system notify handlers per device
ACPI / PM: Add more run-time wake-up fields
ACPI: Use GPE reference counting to support shared GPEs
PCI PM: Make it possible to force using INTx for PCIe PME signaling
PCI PM: PCIe PME root port service driver
PCI PM: Add function for checking PME status of devices
PCI: mark is_pcie obsolete
PCI: set PCI_PREF_RANGE_TYPE_64 in pci_bridge_check_ranges
PCI: pciehp: second try to get big range for pcie devices
...
Now that we return the new resource start position, there is no
need to update "struct resource" inside the align function.
Therefore, mark the struct resource as const.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
As suggested by Linus, align functions should return the start
of a resource, not void. An update of "res->start" is no longer
necessary.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Ignoring the last page when ddr size is 128M. Cached accesses to last page
is causing the processor to prefetch using address above 128M stepping out
of the DDR address space.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/981/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/mm/highmem.c: In function 'kmap_init':
arch/mips/mm/highmem.c:130: error: 'init_mm' undeclared (first use in this function)
arch/mips/mm/highmem.c:130: error: (Each undeclared identifier is reported only once
arch/mips/mm/highmem.c:130: error: for each function it appears in.)
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/980/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The patch that adds cpu_probe_vmbits is erroneously writing to reserved
bit 12. Since we are really only probing high bits, don't write this bit
with a one.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Patchwork: http://patchwork.linux-mips.org/patch/949/
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Test the value that was just allocated rather than the previously tested one.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
expression *x;
expression e;
identifier l;
@@
if (x == NULL || ...) {
... when forall
return ...; }
... when != goto l;
when != x = e
when != &x
*x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
To: linux-mips@linux-mips.org
To: linux-kernel@vger.kernel.org
To: kernel-janitors@vger.kernel.org
Patchwork: http://patchwork.linux-mips.org/patch/945/
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
cpu_cache_init and the things it calls should all be __cpuinit instead
of __devinit.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/938/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
RTC support was rewritten but the defconfig files were not updated. Enable
IPv6 support which for some folks already is a must have. Assign useful
values to other new options.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As reported by Maxime Bizon, the commit "MIPS: PowerTV: Fix support for
timer interrupts with > 64 external IRQs" have broken the r4k timer
since it didn't initialize the cp0_compare_irq_shift variable used in
c0_compare_int_pending() on the architectures whose cpu_has_mips_r2 is
false.
This patch fixes it via initializing the cp0_compare_irq_shift as the
cp0_compare_irq used in the old c0_compare_int_pending().
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: David VomLehn <dvomlehn@cisco.com>
Cc: mbizon@freebox.fr
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/922/
Tested-by: Shane McDonald <mcdonald.shane@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Linux kernel 2.6.32 and later allocate address space from the top of the
kernel virtual memory address space.
This patch implements virtual memory size detection for 64 bit MIPS CPUs
to avoid resulting crashes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/935/
Reviewed-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
DBDMA descriptors need to be located at 32-byte aligned addresses;
however kmalloc in conjunction with the SLAB allocator and
CONFIG_DEBUG_SLUB enabled doesn't deliver any. The dbdma code works
around that by allocating a larger area and realigning the start
address within it.
When freeing a channel however this adjustment is not taken into
account which results in an oops:
Kernel bug detected[#1]:
[...]
Call Trace:
[<80186010>] cache_free_debugcheck+0x284/0x318
[<801869d8>] kfree+0xe8/0x2a0
[<8010b31c>] au1xxx_dbdma_chan_free+0x2c/0x7c
[<80388dc8>] au1x_pcm_dbdma_free+0x34/0x4c
[<80388fa8>] au1xpsc_pcm_close+0x28/0x38
[<80383cb8>] soc_codec_close+0x14c/0x1cc
[<8036dbb4>] snd_pcm_release_substream+0x60/0xac
[<8036dc40>] snd_pcm_release+0x40/0xa0
[<8018c7a8>] __fput+0x11c/0x228
[<80188f60>] filp_close+0x7c/0x98
[<80189018>] sys_close+0x9c/0xe4
[<801022a0>] stack_done+0x20/0x3c
Fix this by recording the address delivered by kmalloc() and using
it as parameter to kfree().
This fix is only necessary with the SLAB allocator and CONFIG_DEBUG_SLAB
enabled; non-debug SLAB, SLUB do return nicely aligned addresses,
debug-enabled SLUB currently panics early in the boot process.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/878/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MIPS processor is limited to 64 external interrupt sources. Using a
greater number without IRQ sharing requires reading platform-specific
registers. On such platforms, reading the IntCtl register to determine
which interrupt corresponds to a timer interrupt will not work.
On MIPSR2 systems there is a solution - the TI bit in the Cause register,
specifically indicates that a timer interrupt has occured. This patch uses
that bit to detect interrupts for MIPSR2 processors, which may be expected
to work regardless of how the timer interrupt may be routed in the hardware.
Signed-off-by: David VomLehn (dvomlehn@cisco.com)
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/804/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pre-compute addresses for the basic ASIC registers. This speeds up access
and allows memory for unused configurations to be freed. In addition,
uninitialized register addresses will be returned as NULL to catch bad
usage quickly.
Signed-off-by: David VomLehn <dvomlehn@cisco.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/806/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
