The following patchset cleans up the atmel_serial driver a bit, moves a
significant portion of the interrupt handler into a tasklet, and adds DMA
support. This is the result of a combined effort by Chip Coldwell, Remy
Bohmer and me. The patches should apply cleanly onto Linus' latest git tree,
and I've also tested it on -mm (with a couple of avr32 fixes applied to make
the rest of the tree compile.)
With DMA, I see transfer rates around 92 kbps when transferring a big file
using ZModem (both directions are roughly the same.) I've also tested the same
thing with a bunch of debug options enabled. The transfer rate is slightly
lower, but no errors are reported.
Note that break and error handling doesn't work too well with DMA enabled.
This is a common problem with all the efforts I've seen adding DMA support to
this driver (including my own). The PDC error handling also accesses icount
without locking. I'm tempted to just ignore the problem for now and hopefully
come up with a solution later.
This patch:
The atmel_serial driver never had a MAINTAINERS entry, although Andrew Victor
has effectively been acting as a maintainer since he got the driver merged
into mainline in the first place.
I'll keep Cc'ing Andrew on all patches, but I'm going to take the main
responsibility for getting things moving upstream from now on.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I've tried to contact Ben Fennema a few times but without success. Since I'm
currently probably closest to being an UDF maintainer, I guess it's fine to
also change the entry in MAINTAINERS.
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: <bfennema@falcon.csc.calpoly.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a rewrite of the ramdisk block device driver.
The old one is really difficult because it effectively implements a block
device which serves data out of its own buffer cache. It relies on the dirty
bit being set, to pin its backing store in cache, however there are non
trivial paths which can clear the dirty bit (eg. try_to_free_buffers()),
which had recently lead to data corruption. And in general it is completely
wrong for a block device driver to do this.
The new one is more like a regular block device driver. It has no idea about
vm/vfs stuff. It's backing store is similar to the buffer cache (a simple
radix-tree of pages), but it doesn't know anything about page cache (the pages
in the radix tree are not pagecache pages).
There is one slight downside -- direct block device access and filesystem
metadata access goes through an extra copy and gets stored in RAM twice.
However, this downside is only slight, because the real buffercache of the
device is now reclaimable (because we're not playing crazy games with it), so
under memory intensive situations, footprint should effectively be the same --
maybe even a slight advantage to the new driver because it can also reclaim
buffer heads.
The fact that it now goes through all the regular vm/fs paths makes it
much more useful for testing, too.
text data bss dec hex filename
2837 849 384 4070 fe6 drivers/block/rd.o
3528 371 12 3911 f47 drivers/block/brd.o
Text is larger, but data and bss are smaller, making total size smaller.
A few other nice things about it:
- Similar structure and layout to the new loop device handlinag.
- Dynamic ramdisk creation.
- Runtime flexible buffer head size (because it is no longer part of the
ramdisk code).
- Boot / load time flexible ramdisk size, which could easily be extended
to a per-ramdisk runtime changeable size (eg. with an ioctl).
- Can use highmem for the backing store.
[akpm@linux-foundation.org: fix build]
[byron.bbradley@gmail.com: make rd_size non-static]
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Byron Bradley <byron.bbradley@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add architecture support for the MN10300/AM33 CPUs produced by MEI to the
kernel.
This patch also adds board support for the ASB2303 with the ASB2308 daughter
board, and the ASB2305. The only processor supported is the MN103E010, which
is an AM33v2 core plus on-chip devices.
[akpm@linux-foundation.org: nuke cvs control strings]
Signed-off-by: Masakazu Urade <urade.masakazu@jp.panasonic.com>
Signed-off-by: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The device is manufactured by IPWireless. In some countries (for
example Czech Republic, T-Mobile ISP) this card is shipped for service
called UMTS 4G.
It's a piece of PCMCIA "4G" UMTS PPP networking hardware that presents
itself as a serial character device (i.e. looks like usual modem to
userspace, accepts AT commands, etc).
Rewieved-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Ben Martel <benm@symmetric.co.nz>
Signed-off-by: Stephen Blackheath <stephen@symmetric.co.nz>
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that I have got the necessary piece of hardware (thanks, Thiemo!), I may
well offer myself as the maintainer for the dz serial driver. I hope nobody
objects.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I have been prime author and maintainer of block2mtd from day one, but
neither MAINTAINERS nor the module source makes this fact clear. And while
I'm at it, update my email addresses tree-wide, as the old address
currently bounces and change my name to "joern" as unicode will likely
continue to cause trouble until the end of this century.
Signed-off-by: Joern Engel <joern@lazybastard.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This gave me bounces and moans when chasing CS5536 so document it.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is based on the 2004 out-of-tree work of Jamey Hicks, to add
support via WMI for controlling the jog dial and wireless on these
tablets.
v1:
Original release
v2:
As per Joshua Wise's comments, change bluetooth to jogdial (an error from
the original driver).
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
CC: Matthew Garrett <mjg59@srcf.ucam.org>
CC: Jamey Hicks <jamey.hicks@nokia.com>
CC: Joshua Wise <joshua@joshuawise.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This is a driver for newer Acer (and Wistron) laptops. It adds wireless
radio and bluetooth control, and on some laptops, exposes the mail LED and
LCD backlight.
v1:
* Initial release
v2:
* Replace left over ACPI references with WMI
* Add GUID based autoloading (depends on future work to WMI)
* Add DMI based autoloading (backup solution until WMI sysfs/ class
work is available)
* Checkpatch fixes
v3:
* Add new EC quirks for Aspire 3100 & 5100, and Extensa 5220
v4:
* Simplified internal handling of WMID and AMW0 devices
* Add autodetection for bluetooth and maximum brightness on AMW0 V2 and
WMID laptops.
v5:
* Add EC quirk for Medion MD 98000
* Add autodetection for AMW0, and mail LED on AMW0 and AMW0 V2.
* Improve error handling
* Fix AMW0 V2 bluetooth and wireless, by using both WMID and AMW0 methods
to ensure that the correct value is always set.
v6:
* Fix 'use before initialisation' bug with quirks.
v7
* Fix bug on AMW0 where acer-wmi would exit if a mail LED was not
detected.
* Add Acer Aspire 9110 mail LED support
* Fix section mismatch warnings
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
CC: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The following is an implementation of the Windows Management
Instrumentation (WMI) ACPI interface mapper (PNP0C14).
What it does:
Parses the _WDG method and exports functions to process WMI method calls,
data block query/ set commands (both based on GUID) and does basic event
handling.
How: WMI presents an in kernel interface here (essentially, a minimal
wrapper around ACPI)
(const char *guid assume the 36 character ASCII representation of
a GUID - e.g. 67C3371D-95A3-4C37-BB61-DD47B491DAAB)
wmi_evaluate_method(const char *guid, u8 instance, u32 method_id,
const struct acpi_buffer *in, struct acpi_buffer *out)
wmi_query_block(const char *guid, u8 instance,
struct acpi_buffer *out)
wmi_set_block(const char *guid, u38 instance,
const struct acpi_buffer *in)
wmi_install_notify_handler(acpi_notify_handler handler);
wmi_remove_notify_handler(void);
wmi_get_event_data(u32 event, struct acpi_buffer *out)
wmi_has_guid(const char guid*)
wmi_has_guid() is a helper function to find if a GUID exists or not on the
system (a quick and easy way for WMI dependant drivers to see if the
the method/ block they want exists, since GUIDs are supposed to be unique).
Event handling - allow a WMI based driver to register a notifier handler
for each GUID with WMI. When a notification is sent to a GUID in WMI, the
handler registered with WMI is then called (it is left to the caller to
ask for the WMI event data associated with the GUID, if needed).
What it won't do:
Unicode - The MS article[1] calls for converting between ASCII and Unicode (or
vice versa) if a GUID is marked as "string". This is left up to the calling
driver.
Handle a MOF[1] - the WMI mapper just exports methods, data and events to
userspace. MOF handling is down to userspace.
Userspace interface - this will be added later.
[1] http://www.microsoft.com/whdc/system/pnppwr/wmi/wmi-acpi.mspx
===
ChangeLog
==
v1 (2007-10-02):
* Initial release
v2 (2007-10-05):
* Cleaned up code - split up super "wmi_evaluate_block" -> each external
symbol now handles its own ACPI calls, rather than handing off to
a "super" method (and in turn, is a lot simpler to read)
* Added a find_guid() symbol - return true if a given GUID exists on
the system
* wmi_* functions now return type acpi_status (since they are just
fancy wrappers around acpi_evaluate_object())
* Removed extra debug code
v3 (2007-10-27)
* More code clean up - now passes checkpatch.pl
* Change data block calls - ref MS spec, method ID is not required for
them, so drop it from the function parameters.
* Const'ify guid in the function call parameters.
* Fix _WDG buffer handling - copy the data to our own private structure.
* Change WMI from tristate to bool - otherwise the external functions are
not exported in linux/acpi.h if you try to build WMI as a module.
* Fix more flag comparisons.
* Add a maintainers entry - since I wrote this, I should take the blame
for it.
v4 (2007-10-30)
* Add missing brace from after fixing checkpatch errors.
* Rewrote event handling - allow external drivers to register with WMI to
handle WMI events
* Clean up flags and sanitise flag handling
v5 (2007-11-03)
* Add sysfs interface for userspace. Export events over netlink again.
* Remove module left overs, fully convert to built-in driver.
* Tweak in-kernel API to use u8 for instance, since this is what the GUID
blocks use (so instance cannot be greater than u8).
* Export wmi_get_event_data() for in kernel WMI drivers.
v6 (2007-11-07)
* Split out userspace into a different patch
v7 (2007-11-20)
* Fix driver to handle multiple PNP0C14 devices - store all GUIDs using
the kernel's built in list functions, and just keep adding to the list
every time we handle a PNP0C14 devices - GUIDs will always be unique,
and WMI callers do not know or care about different devices.
* Change WMI event handler registration to use its' own event handling
struct; we should not pass an acpi_handle down to any WMI based drivers
- they should be able to function with only the calls provided in WMI.
* Update my e-mail address
v8 (2007-11-28)
* Convert back to a module.
* Update Kconfig to default to building as a module.
* Remove an erroneous printk.
* Simply comments for string flag (since we now leave the handling to the
caller).
v9 (2007-12-07)
* Add back missing MODULE_DEVICE_TABLE for autoloading
* Checkpatch fixes
v10 (2007-12-12)
* Workaround broken GUIDs declared expensive without a WCxx method.
* Minor cleanups
v11 (2007-12-17)
* More fixing for broken GUIDs declared expensive without a WCxx method.
* Add basic EmbeddedControl region handling.
v12 (2007-12-18)
* Changed EC region handling code, as per Alexey's comments.
v13 (2007-12-27)
* Changed event handling so that we can have one event handler registered
per GUID, as per Matthew Garrett's suggestion.
v14 (2008-01-12)
* Remove ACPI debug statements
v15 (2008-02-01)
* Replace two remaining 'x == NULL' type tests with '!x'
v16 (2008-02-05)
* Change MAINTAINERS entry, as I am not, and never have been, paid to work
on WMI
* Remove 'default' line from Kconfig
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
CC: Matthew Garrett <mjg59@srcf.ucam.org>
CC: Alexey Starikovskiy <aystarik@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] make pfm_get_task work with virtual pids
[IA64] honor notify_die() returning NOTIFY_STOP
[IA64] remove dead code: __cpu_{down,die} from !HOTPLUG_CPU
[IA64] Appoint kvm/ia64 Maintainers
[IA64] ia64_set_psr should use srlz.i
[IA64] Export three symbols for module use
[IA64] mca style cleanup
[IA64] sn_hwperf semaphore to mutex
[IA64] generalize attribute of fsyscall_gtod_data
[IA64] efi.c Add /* never reached */ annotation
[IA64] efi.c Spelling/punctuation fixes
[IA64] Make efi.c mostly fit in 80 columns
[IA64] aliasing-test: fix gcc warnings on non-ia64
[IA64] Slim-down __clear_bit_unlock
[IA64] Fix the order of atomic operations in restore_previous_kprobes on ia64
[IA64] constify function pointer tables
[IA64] fix userspace compile error in gcc_intrin.h
Add a standard NIC and RDMA/iWARP driver for NetEffect 1/10Gb ethernet adapters.
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Anthony and Xiantao are working on KVM for ia64.
Signed-off-by Anthony Xu <anthony.xu@intel.com>
Signed-off-by Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
On Sat, 2007-12-22 at 18:08 -0500, Corey Thomas wrote:
> This email, coreythomas@charter.net is good. ISP change.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Remove Chad Tindel; he hasn't been involved for a number
of years.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Peter's email address is bouncing
- the project webpage no longer exists
- neither Peter nor Mike had a single patch included in the kernel
since 2.6.12-rc2 (when the git history begins)
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.infradead.org/battery-2.6:
apm_power: check I.intval for zero value, we use it as the divisor
MAINTAINERS: remove kernel-discuss@handhelds.org list
pda_power: implement polling
pda_power: various cleanups
apm_power: support using VOLTAGE_* properties for apm calculations
pda_power: add suspend/resume support
power_supply: add few more values and props
pda_power: only register available psu
power: fix incorrect unregistration in power_supply_create_attrs error path
power: remove POWER_SUPPLY_PROP_CAPACITY_LEVEL
[BATTERY] power_supply_leds: use kasprintf
[BATTERY] Every file should include the headers containing the prototypes for its global functions.
nfs@lists.sourceforge.net is being decommissioned.
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
New driver for wireless RNDIS devices. So far only known chip that uses
wireless RNDIS is Broadcom 4320. Driver detects all RNDIS devices that
have RNDIS wireless physical medium. At least following devices are
detected:
Buffalo WLI-U2-KG125S
U.S. Robotics USR5421
Belkin F5D7051
Linksys WUSB54GSv2
Linksys WUSB54GSC
Asus WL169gE
Eminent EM4045
BT Voyager 1055
Linksys WUSB54GSv1
U.S. Robotics USR5420
BUFFALO WLI-USB-G54
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add myself as a point of contact for the ALSA SoC subsystem and add a
reference to the development GIT tree.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
add ath5k wireless driver
Portions of this driver are covered by one or both of the ISC and
3-clause BSD licenses. Specific license information is cited at the top
of each file.
Acked-by and Signed-off-by information is collected from individual
patches as collected in the wireless-2.6 tree prior to upstream
submission.
Acked-by: Matthew W. S. Bell <mentor@madwifi.org>
Acked-by: Michael Taylor <mike.taylor@apprion.com>
Acked-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bradley M. Kuhn <bkuhn@softwarefreedom.org>
Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Francesco Gringoli <francesco.gringoli@ing.unibs.it>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Karen Sandler <karen@softwarefreedom.org>
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: Matt Norwood <norwood@softwarefreedom.org>
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Richard Fontana <fontana@softwarefreedom.org>
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Ulrich Meis <meis@nets.rwth-aachen.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds me as maintainer of the RDC R6040 Fast Ethernet driver.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
--
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Also fix Zhu Yi's name.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add an entry in MAINTAINERS for rc80211-pid.
Cc: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Schedule bcm43xx for for removal in the 2.6.26 development window.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds entries in the CREDITS and MAINTAINERS file for CAN.
Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: Urs Thuermann <urs.thuermann@volkswagen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (200 commits)
[SCSI] usbstorage: use last_sector_bug flag universally
[SCSI] libsas: abstract STP task status into a function
[SCSI] ultrastor: clean up inline asm warnings
[SCSI] aic7xxx: fix firmware build
[SCSI] aacraid: fib context lock for management ioctls
[SCSI] ch: remove forward declarations
[SCSI] ch: fix device minor number management bug
[SCSI] ch: handle class_device_create failure properly
[SCSI] NCR5380: fix section mismatch
[SCSI] sg: fix /proc/scsi/sg/devices when no SCSI devices
[SCSI] IB/iSER: add logical unit reset support
[SCSI] don't use __GFP_DMA for sense buffers if not required
[SCSI] use dynamically allocated sense buffer
[SCSI] scsi.h: add macro for enclosure bit of inquiry data
[SCSI] sd: add fix for devices with last sector access problems
[SCSI] fix pcmcia compile problem
[SCSI] aacraid: add Voodoo Lite class of cards.
[SCSI] aacraid: add new driver features flags
[SCSI] qla2xxx: Update version number to 8.02.00-k7.
[SCSI] qla2xxx: Issue correct MBC_INITIALIZE_FIRMWARE command.
...
we are planning a major rewrite of the zfcp driver,
meaning that a lot of patches will hit the mailing-list in the near future.
Since I can't support this additional work-load along with my other
responsibilities we are shifting the maintainership to
Christof Schmitt as the maintainer and
Martin Peschke as the co-maintainer.
Please support the two in providing us a new and more stable
zfcp environment.
Thanks
Swen
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Unfortunately Jeb decided to move away from our group. We wish Jeb
good luck with his new group!
Reordered people a bit so most active team members are on top.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My Unix email account is being discontinued at end of Q1 '08.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
L: entries should be email addresses
Change L:http entries to W:http
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds an entry for the Userspace I/O framework to MAINTAINERS.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add Dan Williams as maintainer for libertas driver.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.linux-nfs.org/pub/linux/nfs-2.6:
MAINTAINERS: update the NFS CLIENT entry
NFS: Fix an Oops in NFS unmount
Revert "NFS: Ensure we return zero if applications attempt to write zero bytes"
SUNRPC xprtrdma: fix XDR tail buf marshalling for all ops
NFSv2/v3: Fix a memory leak when using -onolock
NFS: Fix NFS mountpoint crossing...
tipar: remove obsolete module
The tipar character driver was used to implement bit-banging access
to Texas Instruments parallel link cable. A user-land method now
exists thru PPDEV & PARPORT.
Signed-off-by: Romain Liévin <roms@lpg.ticalc.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add in the new NFS mailing list on vger, website, and git tree info, and
update my email address to reflect the fact that I've been working for
netapp for the past 2 years.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
[PARISC] lba_pci: pci_claim_resources disabled expansion roms
[PARISC] print more than one character at a time for pdc console
[PARISC] Update parisc-linux MAINTAINERS entries
[PARISC] timer interrupt should not be IRQ_DISABLED
Revert "[PARISC] import necessary bits of libgcc.a"
I haven't seen Richard doing MTRR related work for quite some time, and
the "X86 ARCHITECTURE" entry in MAINTAINERS already covers the people
currently responsible for this code.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4680/1: parentheses around NR_IRQS definition
[ARM] 4679/1: AT91: Change maintainer email address
[ARM] 4675/1: pxa: fix mfp address definition error for pxa320
[ARM] 4674/1: pxa: increase LCD PCLK drive strength to fast 2mA for PXA300/PXA310
[ARM] 4673/1: pxa: add missing IRQ_SSP4 definitions for PXA3xx
[ARM] 4672/1: pxa: fix DRCMR(n) to support PXA27x and later processors
[ARM] 4665/1: fix __und_usr wrt accessing the undefined insn in user space
[ARM] 4659/1: remove possibilities for spurious false negative with __kuser_cmpxchg
[ARM] 4661/1: fix do_undefinstr wrt the enabling of IRQs
[ARM] uengine: fix memset size error
[ARM] 4648/1: i.MX/MX1 ensure more complete AITC initialization
[ARM] 4611/2: AT91: Fix GPIO buttons pins on SAM9261-EK.
[ARM] 4650/1: AT91: New-style init of I2C, support for i2c-gpio
[ARM] 4604/2: AT91: Master clock divistor on SAM9
[ARM] 4662/1: Fix PXA serial driver compilation if SERIAL_PXA_CONSOLE is disabled
[ARM] PXA ssp: unlock when ssp tries to close an invalid port
[ARM] 4654/1: pxa: update default MFP register value
[ARM] 4653/1: pxa: fix a gpio typo in mfp-pxa320.h
[ARM] 4652/1: pxa: fix a typo of pxa27x usb host clk definition
[ARM] 4651/1: pxa: add PXA3xx specific IRQ definitions
Digging through old mail, I found a note about needing to remove the
separate entry for the USB HUB driver. It's not been separable from
usbcore (host side!) since quite early in the 2.4 kernel series.
And Johanness certainly isn't involved with it any more.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/net-2.6: (41 commits)
[XFRM]: Fix leak of expired xfrm_states
[ATM]: [he] initialize lock and tasklet earlier
[IPV4]: Remove bogus ifdef mess in arp_process
[SKBUFF]: Free old skb properly in skb_morph
[IPV4]: Fix memory leak in inet_hashtables.h when NUMA is on
[IPSEC]: Temporarily remove locks around copying of non-atomic fields
[TCP] MTUprobe: Cleanup send queue check (no need to loop)
[TCP]: MTUprobe: receiver window & data available checks fixed
[MAINTAINERS]: tlan list is subscribers-only
[SUNRPC]: Remove SPIN_LOCK_UNLOCKED
[SUNRPC]: Make xprtsock.c:xs_setup_{udp,tcp}() static
[PFKEY]: Sending an SADB_GET responds with an SADB_GET
[IRDA]: Compilation for CONFIG_INET=n case
[IPVS]: Fix compiler warning about unused register_ip_vs_protocol
[ARP]: Fix arp reply when sender ip 0
[IPV6] TCPMD5: Fix deleting key operation.
[IPV6] TCPMD5: Check return value of tcp_alloc_md5sig_pool().
[IPV4] TCPMD5: Use memmove() instead of memcpy() because we have overlaps.
[IPV4] TCPMD5: Omit redundant NULL check for kfree() argument.
ieee80211: Stop net_ratelimit/IEEE80211_DEBUG_DROP log pollution
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6.24:
sh: include ax88796 in the defconfig for r7785rp
sh: include ax88796 in the defconfig for r7780mp
sh: fix R2D-1 CF support
fb: Orphan imsttfb.
sh: Update mailing list info.
sh: lockless UTLB miss fast-path.
sh: Kill off UTLB flush in fast-path.
sh: Fix copy_{to,from}_user_page() with cache disabled.
The mail service for the mac.linux-m68k.org domain is defunct.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Your mail to 'Tlan-devel' with the subject
drivers/net/tlan question
Is being held until the list moderator can review it for approval.
The reason it is being held:
Post by non-member to a members-only list
Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
I haven't had this hardware in years, so kill off my MAINTAINERS entry
for this and flag it as orphaned.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
DaveM has provided a vger list, update MAINTAINERS to reflect this.
Also, rip out the sh64 entry (as this can just be rolled in to the
general sh case), and add the git path.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch marks softmac as obsolete in MAINTAINERS and removes Joe and
myself as maintainers, we're no longer using it nor interested in the
code in any way. Also remove the website reference because I took it
offline. Hopefully the code will go away in 2.6.25.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Joseph Jezak <josejx@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As b43legacy is going to be orphaned, add me as a maintainer. Fix URLs for
the related website and fix my e-mail address in MAINTAINERS file.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: linux-input mailing list moved to vger.kernel.org
Input: inport, logibm - use KERN_INFO when reporting missing mouse
Input: appletouch - idle reset logic broke older Fountains
Input: hp_sdc.c - fix section mismatch
Input: appletouch - add Johannes Berg as maintainer
Input: Add Euro and Dollar key codes
Input: xpad - add more USB IDs
After the last patch that broke appletouch for powerbooks again I'd like
to take over maintainership of this driver to make sure it doesn't break
again in the future.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This adds myself as mac80211 maintainer and updates the git URL to point
to the wireless-2.6 tree. Also move Jiri down so he isn't first in list.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
[IPV4]: Explicitly call fib_get_table() in fib_frontend.c
[NET]: Use BUILD_BUG_ON in net/core/flowi.c
[NET]: Remove in-code externs for some functions from net/core/dev.c
[NET]: Don't declare extern variables in net/core/sysctl_net_core.c
[TCP]: Remove unneeded implicit type cast when calling tcp_minshall_update()
[NET]: Treat the sign of the result of skb_headroom() consistently
[9P]: Fix missing unlock before return in p9_mux_poll_start
[PKT_SCHED]: Fix sch_prio.c build with CONFIG_NETDEVICES_MULTIQUEUE
[IPV4] ip_gre: sendto/recvfrom NBMA address
[SCTP]: Consolidate sctp_ulpq_renege_xxx functions
[NETLINK]: Fix ACK processing after netlink_dump_start
[VLAN]: MAINTAINERS update
[DCCP]: Implement SIOCINQ/FIONREAD
[NET]: Validate device addr prior to interface-up
> I guess it is time to clarify that suspend and hibernation are separate
> things, and add Rafael as a maintainer. Plus, people blame us for suspend
> problems, anyway, I guess it is fair to mark us as suspend maintainers, too.
If blame is the qualification, I guess I'm already part of this merry band:-)
Change to Supported from Maintained, as the folks that sign my paycheck
agree it is a good idea for me to help out on suspend.
Acked-by: Pavel Machek <pavel@suse.cz>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Newly minted project home page -- http://www.lesswatts.org/projects/acpi/
Konstantin moved on, so default back to Len for Thermal/Fan.
Rui replaces Luming on video.
Signed-off-by: Len Brown <len.brown@intel.com>
Ben stepped down from VLAN maintainership due to a lack of time, add
myself as new maintainer.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (39 commits)
Remove Andrew Morton from list of net driver maintainers.
bonding: Acquire correct locks in alb for promisc change
bonding: Convert more locks to _bh, acquire rtnl, for new locking
bonding: Convert locks to _bh, rework alb locking for new locking
bonding: Convert miimon to new locking
bonding: Convert balance-rr transmit to new locking
Convert bonding timers to workqueues
Update MAINTAINERS to reflect my (jgarzik's) current efforts.
pasemi_mac: fix typo
defxx.c: dfx_bus_init() is __devexit not __devinit
s390 MAINTAINERS
remove header_ops bug in qeth driver
sky2: crash on remove
MIPSnet: Delete all the useless debugging printks.
AR7 ethernet: small post-merge cleanups and fixes
mv643xx_eth: Hook up mv643xx_get_sset_count
mv643xx_eth: Remove obsolete checksum offload comment
mv643xx_eth: Merge drivers/net/mv643xx_eth.h into mv643xx_eth.c
mv643xx_eth: Remove unused register defines
mv643xx_eth: Clean up mv643xx_eth.h
...
Remove net driver entries (they fall under the more general 'net driver
maintainer') umbrella.
Remove entries for older drivers that either no longer exist, are about
to be removed, or I no longer care about.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
adding Frank Blaschka to s390 networking maintainers
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Vitaly has been doing most of the 8xx maintenance work.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add new maintainers for the x86 (32-bit and 64-bit) architecture.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
kbuild: fix first module build
kconfig: update kconfig-language text
kbuild: introduce cc-cross-prefix
kbuild: disable depmod in cross-compile kernel build
kbuild: make deb-pkg - add 'Provides:' line
kconfig: comment typo in scripts/kconfig/Makefile.
kbuild: stop docproc segfaulting when SRCTREE isn't set.
kbuild: modpost problem when symbols move from one module to another
kbuild: cscope - filter out .tmp_* in find_sources
kbuild: mailing list has moved
kbuild: check asm symlink when building a kernel
This patch contains the next round of scheduled OSS code removal.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I'm not sure that the new URL satifies the requirement of status/info, but
it does at least as good a job as the old URL, and contains current
releases of kexec-tools, rather than somewhat ancient versions.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The old list at sourceforge had a few issues:
- it was subscriber-only
- it were relying on moderation
And I could see several mails did not get to the list lately
so I decided this was a good time for a new list.
I already requested marc.info to archieve the new list -
and I dunno where else the old list was archieved but we
ought to update.
I have no access to the list of subscribers on the old list
so people will have to subscribe manually.
How to subscribe:
send a mail to: majordomo@vger.kernel.org
containing following text:
subscribe linux-kbuild
See also http://vger.kernel.org/vger-lists.html
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
The email address that I use for man-pages maintenance has changed as of
now. This patch changes the address in Documentation/HOWTO and
MAINTAINERS.
Signed-off-by: Michael Kerrisk <mtk.manpages@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I simply don't have any old IDE systems any more or time to really look
after this. Nobody responded to the previous linux-ide mail about
maintainers so...
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
You are not allowed to post to this mailing list, and your message has been
automatically rejected. If you think that your messages are being rejected
in error, contact the mailing list owner at
linux-omap-open-source-owner@linux.omap.com.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (40 commits)
kbuild: introduce ccflags-y, asflags-y and ldflags-y
kbuild: enable 'make CPPFLAGS=...' to add additional options to CPP
kbuild: enable use of AFLAGS and CFLAGS on commandline
kbuild: enable 'make AFLAGS=...' to add additional options to AS
kbuild: fix AFLAGS use in h8300 and m68knommu
kbuild: check for wrong use of CFLAGS
kbuild: enable 'make CFLAGS=...' to add additional options to CC
kbuild: fix up CFLAGS usage
kbuild: make modpost detect unterminated device id lists
kbuild: call export_report from the Makefile
kbuild: move Kai Germaschewski to CREDITS
kconfig/menuconfig: distinguish between selected-by-another options and comments
kconfig: tristate choices with mixed tristate and boolean values
include/linux/Kbuild: remove duplicate entries
kbuild: kill backward compatibility checks
kbuild: kill EXTRA_ARFLAGS
kbuild: fix documentation in makefiles.txt
kbuild: call make once for all targets when O=.. is used
kbuild: pass -g to assembler under CONFIG_DEBUG_INFO
kbuild: update _shipped files for kconfig syntax cleanup
...
Fix up conflicts in arch/um/sys-{x86_64,i386}/Makefile manually.
* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6: (53 commits)
hwmon: (vt8231) fix sparse warning
hwmon: (sis5595) fix sparse warning
hwmon: (w83627hf) don't assume bank 0
hwmon: (w83627hf) Fix setting fan min right after driver load
hwmon: (w83627hf) De-macro sysfs callback functions
hwmon: Add new combined driver for FSC chips
hwmon: (ibmpex) Release IPMI user if hwmon registration fails
hwmon: (dme1737) Add sch311x support
hwmon: (dme1737) group functions logically
hwmon: (dme1737) cleanups
hwmon: IBM power meter driver
hwmon: (coretemp) Add support for Celeron 4xx
hwmon: (lm87) Disable VID when it should be
hwmon: (w83781d) Add individual alarm and beep files
hwmon: VRM is not read from registers
MAINTAINERS: update hwmon subsystem git trees
hwmon: Fix the code examples in documentation
hwmon: update sysfs interface document - error handling
hwmon: (thmc50) Fix a debug message
hwmon: (thmc50) Don't create temp3 if not enabled
...
Since there is no x86-64 architecture anymore it cannot be maintained.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a driver for the Atmel USBA UDC which can be found integrated
on AT32AP700x AVR32 processors. For hardware documentation, please see
the AT32AP7000 data sheet:
http://www.atmel.com/dyn/resources/prod_documents/doc32003.pdf
This is a dual speed controller (connects at high or full speed).
The driver supports up to 7 control, bulk, interrupt and isochronous
endpoints with some constraints. Bulk, interrupt and isochronous
transfers are driven by DMA.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kai is not active in kernel development these
days so give him credit for his major kbuild
contribution and ISDN work.
Acked-by: Kai Germaschewski <kai@germaschewski.name>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Mailing list changed. The former list at mpt_linux_developer@lsi.com is no
longer in service. Please use the new email provided listed in this patch.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Update the version to 3.4
Add my copyright
Add myself to MAINTAINERS
Exercise my right to change the license from dual BSD/GPL to GPL
Don't force the definition of CONFIG_ISA on x86
Always include pci.h
Stop including stat.h
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (408 commits)
[POWERPC] Add memchr() to the bootwrapper
[POWERPC] Implement logging of unhandled signals
[POWERPC] Add legacy serial support for OPB with flattened device tree
[POWERPC] Use 1TB segments
[POWERPC] XilinxFB: Allow fixed framebuffer base address
[POWERPC] XilinxFB: Add support for custom screen resolution
[POWERPC] XilinxFB: Use pdata to pass around framebuffer parameters
[POWERPC] PCI: Add 64-bit physical address support to setup_indirect_pci
[POWERPC] 4xx: Kilauea defconfig file
[POWERPC] 4xx: Kilauea DTS
[POWERPC] 4xx: Add AMCC Kilauea eval board support to platforms/40x
[POWERPC] 4xx: Add AMCC 405EX support to cputable.c
[POWERPC] Adjust TASK_SIZE on ppc32 systems to 3GB that are capable
[POWERPC] Use PAGE_OFFSET to tell if an address is user/kernel in SW TLB handlers
[POWERPC] 85xx: Enable FP emulation in MPC8560 ADS defconfig
[POWERPC] 85xx: Killed <asm/mpc85xx.h>
[POWERPC] 85xx: Add cpm nodes for 8541/8555 CDS
[POWERPC] 85xx: Convert mpc8560ads to the new CPM binding.
[POWERPC] mpc8272ads: Remove muram from the CPM reg property.
[POWERPC] Make clockevents work on PPC601 processors
...
Fixed up conflict in Documentation/powerpc/booting-without-of.txt manually.
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (867 commits)
[SKY2]: status polling loop (post merge)
[NET]: Fix NAPI completion handling in some drivers.
[TCP]: Limit processing lost_retrans loop to work-to-do cases
[TCP]: Fix lost_retrans loop vs fastpath problems
[TCP]: No need to re-count fackets_out/sacked_out at RTO
[TCP]: Extract tcp_match_queue_to_sack from sacktag code
[TCP]: Kill almost unused variable pcount from sacktag
[TCP]: Fix mark_head_lost to ignore R-bit when trying to mark L
[TCP]: Add bytes_acked (ABC) clearing to FRTO too
[IPv6]: Update setsockopt(IPV6_MULTICAST_IF) to support RFC 3493, try2
[NETFILTER]: x_tables: add missing ip6t_modulename aliases
[NETFILTER]: nf_conntrack_tcp: fix connection reopening
[QETH]: fix qeth_main.c
[NETLINK]: fib_frontend build fixes
[IPv6]: Export userland ND options through netlink (RDNSS support)
[9P]: build fix with !CONFIG_SYSCTL
[NET]: Fix dev_put() and dev_hold() comments
[NET]: make netlink user -> kernel interface synchronious
[NET]: unify netlink kernel socket recognition
[NET]: cleanup 3rd argument in netlink_sendskb
...
Fix up conflicts manually in Documentation/feature-removal-schedule.txt
and my new least favourite crap, the "mod_devicetable" support in the
files include/linux/mod_devicetable.h and scripts/mod/file2alias.c.
(The latter files seem to be explicitly _designed_ to get conflicts when
different subsystems work with them - that have an absolutely horrid
lack of subsystem separation!)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'block-2.6.24' of git://git.kernel.dk/data/git/linux-2.6-block: (37 commits)
[BLOCK] Fix failing compile with BLK_DEV_IO_TRACE=n
compat_ioctl: move floppy handlers to block/compat_ioctl.c
compat_ioctl: move cdrom handlers to block/compat_ioctl.c
compat_ioctl: move BLKPG handling to block/compat_ioctl.c
compat_ioctl: move hdio calls to block/compat_ioctl.c
compat_ioctl: handle blk_trace ioctls
compat_ioctl: add compat_blkdev_driver_ioctl()
compat_ioctl: move common block ioctls to compat_blkdev_ioctl
Sysace: Don't enable IRQ until after interrupt handler is registered
Sysace: sparse fixes
Sysace: Minor coding convention fixup
drivers/block/umem: use DRIVER_NAME where appropriate
drivers/block/umem: trim trailing whitespace
drivers/block/umem: minor cleanups
drivers/block/umem: use dev_printk()
drivers/block/umem: move private include away from include/linux
Sysace: Labels in C code should not be indented.
Sysace: Add of_platform_bus binding
Sysace: Move IRQ handler registration to occur after FSM is initialized
Sysace: minor rework and cleanup changes
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (74 commits)
Blackfin serial driver: pending a unique anomaly id, tie the break flood issue to ANOMALY_05000230
blackfin enable arbitary speed serial setting
Blackfin arch: Remove cruft - CONFIG_DEBUG_SERIAL_EARLY_INIT and DEBUG_KERNEL_START
Blackfin arch: fix typo in register name
Blackfin arch: trim the Blackfin arch MAINTAINERS list
Blackfin arch: fix bug libstdc++ calling writev with an iovec containing { NULL, 0 } fails on Blackfin
Blackfin arch: Export strcpy - occasionally get module link failures otherwise
Blackfin arch: the load address is not safe to point to as a workaround for ANOMALY 05000281
Blackfin arch: show_mem can not be marked as init, since it is called during OOM condition
Blackfin arch: flush/inv the correct range when using write back cache and fix bugs find by dmacopy
Blackfin arch: update kgdb patch
Blackfin arch: Comply with revised Anomaly Workarounds for BF533 05000311 and BF561 05000323
Blackfin arch: Print out debug info, as early as possible
Blackfin arch: Enable earlyprintk earlier - so any error after our interrupt tables are set up will print out
Blackfin arch: fix endless loop bug when a double fault happens
Blackfin arch: Initial patch to add earlyprintk support
Blackfin arch: add TWIx_REGBASE and SPIx_REGBASE to specific CPU header files, use the new REGBASE for board platform resources
Blackfin arch: modify the insX/outsX and dma_insX/dma_outsX to be compatible with other archs
Blackfin arch: add more common defines for output sections
Blackfin arch: cleanup IO and DMA_IO API function definitions according to other arches
...
Stop building and configuring driver for Digi RightSwitch, which was
never actually sold to anyone, and remove it from MAINTAINERS.
In response to an investigation into the firmware of the "Digi Rightswitch"
driver, Andres Salomon discovered:
>
> Dear Andres:
>
> After further research, we found that this product was killed in place
> and never reached the market. We would like to request that this not be
> included.
Since the product never reached market, clearly nobody is using this orphaned
driver.
Signed-off-by: Nathanael Nerode <neroden@gcc.gnu.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the mac80211 based wireless drivers for the Intel
PRO/Wireless 3945ABG/BG Network Connection and Intel Wireless WiFi
Link AGN (4965) adapters.
[ Move driver into it's own directory -DaveM ]
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SSB is an SoC bus used in a number of embedded devices. The most
well-known of these devices is probably the Linksys WRT54G, but there
are others as well. The bus is also used internally on the BCM43xx
and BCM44xx devices from Broadcom.
This patch also includes support for SSB ID tables in modules, so
that SSB drivers can be loaded automatically.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jesse Huang <jesse@icplus.com.tw>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Intel 82598 PCI-Express 10GbE
chipset. Devices will be available on the market soon.
This version of the driver is largely the same as the last release:
* Driver uses a single RX and single TX queue, each using 1 MSI-X
irq vector.
* Driver runs in NAPI mode only
* Driver is largely multiqueue-ready (TM)
Changes since 20070803:
* removed wrappers for hardware functions
* incorporated e1000e-style HW api reorganization code
* sparse/checkpatch cleanups, namespace cleanups
* driver prints out extra debugging information at load time
identifying adapter board number, mac, phy types
* removed ixgbe_api.c, ixgbe_api.h, ixgbe_osdep.h
* driver update to 1.1.18
* removed ixgbe.txt which contained no useful info anymore
[ Integrated napi_struct changes from Auke as well... -DaveM ]
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a mac80211 wireless driver for ADMtek ADM8211 based
wireless cards.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new sysfs alarm methodology to w83791d driver
Signed-off-by: Charles Spirakis <bezaur@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Powerpc patches should be posted to linuxppc-dev@ozlabs.org, so modify
MAINTAINERS to no longer reference linuxppc-embedded@ozlabs.org.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the latest version of the MMC-over-SPI support. It works
on 2.6.23-rc2 plus git-mmc (from rc1-mm2), along with the preceding
patches which teach the rest of the MMC stack about SPI.
The main issue of note is that sometimes cards need to be power cycled
to recover after certain faults. Also, it may sometimes be necessary
to disable CRCs. ("modprobe mmc_core use_spi_crc=n")
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: mikael.starvik@axis.com,
Cc: Hans-Peter Nilsson <hp@axis.com>
Cc: Jan Nikitenko <jan.nikitenko@gmail.com>
Cc: Mike Lavender <mike@steroidmicros.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Update netfilter list addresses and an old email address of myself.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop the URL for DCO (URL is invalid). Also, point to SubmittingPatches
for the current DCO.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The IOC3 is a multifunction device but not in sense of the PCI
specification. Currently its ethernet and serial functionality are
supported by two separate drivers authored and maintained by different
people, so MAINTAINERS should reflect that.
Cc: Patrick Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
9p: fix bad error path in conversion routines
9p: remove deprecated v9fs_fid_lookup_remove()
9p: update maintainers and documentation
9p: fix use after free
Updates to the MAINTAINERS file and documentation for 9p to point to the
swik wiki versus the outdated sf.net page. Also updated some email addresses
and added pointers to papers which better describe the implementation and
application of the Linux 9p client.
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Fix up the maintainers info in the tpm drivers. Kylene will be out for
some time, so copying the sourceforge list is the best way to get some
attention.
Cc: Marcel Selhorst <tpm@selhorst.net>
Cc: Kylene Jo Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] Check return code on failed alloc
[CIFS] Update CIFS project web site
[CIFS] Fix hang in find_writable_file
Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Also, rename the dma engine entry since it is now a generic offload engine
subsystem, not just memcpy.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Make it more clear to users what kinds of hardware USBHID handles,
so that they can send reports and queries properly.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog: (28 commits)
[WATCHDOG] Fix pcwd_init_module crash
[WATCHDOG] ICH9 support for iTCO_wdt
[WATCHDOG] 631xESB/632xESB support for iTCO_wdt - add all LPC bridges
[WATCHDOG] 631xESB/632xESB support for iTCO_wdt
[WATCHDOG] omap_wdt.c - default error for IOCTL is -ENOTTY
[WATCHDOG] Return value of nonseekable_open
[WATCHDOG] mv64x60_wdt: Rework the timeout register manipulation
[WATCHDOG] mv64x60_wdt: disable watchdog timer when driver is probed
[WATCHDOG] mv64x60_wdt: Support the WDIOF_MAGICCLOSE feature
[WATCHDOG] mv64x60_wdt: Add a module parameter to change nowayout setting
[WATCHDOG] mv64x60_wdt: Add WDIOC_SETOPTIONS ioctl support
[WATCHDOG] mv64x60_wdt: Support for WDIOC_SETTIMEOUT ioctl
[WATCHDOG] mv64x60_wdt: Fix WDIOC_GETTIMEOUT return value
[WATCHDOG] mv64x60_wdt: Check return value of nonseekable_open
[WATCHDOG] mv64x60_wdt: Add arch/powerpc platform support
[WATCHDOG] mv64x60_wdt: Get register address from platform data
[WATCHDOG] mv64x60_wdt: set up platform_device in platform code
[WATCHDOG] ensure mouse and keyboard ignored in w83627hf_wdt
[WATCHDOG] s3c2410_wdt: fixup after arch include moves
[WATCHDOG] git-watchdog-typo
...
The arm26 port has been in a state where it was far from even compiling
for quite some time.
Ian Molton agreed with the removal.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Ian Molton <spyro@f2s.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make Bruce Fields (co-)maintainer of kNFSDd
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove Val Henson as tulip maintainer and let her roam free, FREE!
Signed-off-by: Val Henson <val@nmt.edu>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch implements the driver necessary use the Analog Devices
Blackfin processor's on-chip watchdog controller, supports
BF53[123]/BF53[467]/BF54[2489]/BF561.
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
sdhci: make sure to clear the error interrupt
mmc: at91_mci: wakeup on card insertion (or removal)
mmc: add maintainer for at91
Updating email adress in MAINTAINER file.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6: (44 commits)
i2c: Delete the i2c-isa pseudo bus driver
hwmon: refuse to load abituguru driver on non-Abit boards
hwmon: fix Abit Uguru3 driver detection on some motherboards
hwmon/w83627ehf: Be quiet when no chip is found
hwmon/w83627ehf: No need to initialize fan_min
hwmon/w83627ehf: Export the thermal sensor types
hwmon/w83627ehf: Enable VBAT monitoring
hwmon/w83627ehf: Add support for the VID inputs
hwmon/w83627ehf: Fix timing issues
hwmon/w83627ehf: Add error messages for two error cases
hwmon/w83627ehf: Convert to a platform driver
hwmon/w83627ehf: Update the Kconfig entry
make coretemp_device_remove() static
hwmon: Add LM93 support
hwmon: Improve the pwmN_enable documentation
hwmon/smsc47b397: Don't report missing fans as spinning at 82 RPM
hwmon: Add support for newer uGuru's
hwmon/f71805f: Add temperature-tracking fan control mode
hwmon/w83627ehf: Preserve speed reading when changing fan min
hwmon: fix detection of abituguru volt inputs
...
Manual fixup of trivial conflict in MAINTAINERS file
Add documentation for the new SMSC DME1737 driver.
Signed-off-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Mark M. Hoffman is taking over for Jean Delvare as maintainer of the hwmon
subsystem. He is also the author/maintainer for several existing drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Added new maintainers for the new EDAC drivers.
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the MAINTAINERS file: Thomas Gleixner has been the de-facto
maintainer of POSIX timers and clocks for quite some time.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I guess it is time to clarify that suspend and hibernation are separate
things, and add Rafael as a maintainer. Plus, people blame us for suspend
problems, anyway, I guess it is fair to mark us as suspend maintainers,
too.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Acked-by: Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch implements the driver necessary use the Analog Devices
Blackfin processor's on-chip ethernet MAC controller.
[try#2]
- add timeout control
- kill dma_config_reg bitfields
- some trivial cleanup
[try#3]
- add endianess check
- add DRV_NAME, DRV_VERSION... driver information string
- add some comments for silicon anomaly and dma API confusion
- some code trivial cleanup
[try#4]
- add Blackfin latest GPIO pin mux opertion with Michael Hennerich's
help and Dan's review
- rewrite the DMA descriptor list operation in a more readable way
by Joe's review
[try#5]
- cleanup some coding style by Joe's review.
[try#6]
- 1.1 version fix a bug when set up multicast list pointed by Mr. yoshfuji
- rearrange the desc_list_free function.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a reimplementation of the zs driver for the serial subsystem. Any
resemblance to the old driver is purely coincidential. ;-) I do hope I got
the handling of modem lines right -- better do not tackle me about the
issue unless you feel too good...
Any users of the old driver: please note the numbers of the serial lines
have now been swapped, i.e. ttyS0 <-> ttyS1 and ttyS2 <-> ttyS3. It has
to do with the modem lines mentioned above; basically the port A in a given
chip has to be initialised before the port B if you want to use the latter
as the serial console (which is usually the case), as operations on modem
lines of the serial line associated with the port B access both ports (see
the comment at the top of the driver for the details of wiring used).
Please update your scripts.
This is also the reason each SCC now requests an IRQ once only (as seen in
"/proc/interrupts") -- the handler takes care of both ports at once as the
line associated with the port B has to take status update interrupts from
both ports (and yet the line of the port A takes its own for itself too).
The old driver never got it right...
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.dk/data/git/linux-2.6-block:
splice: direct splicing updates ppos twice
more ACSI removal
umem: Fix match of pci_ids in umem driver
umem: Remove references to dead CONFIG_MM_MAP_MEMORY variable
remove the documentation for the legacy CDROM drivers
This patch contains the scheduled removal of OSS drivers that:
- have ALSA drivers for the same hardware without known regressions and
- whose Kconfig options have been removed in 2.6.20.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add entries to MAINTAINERS for I/OAT and DMAENGINE
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the documentation for the removed legacy CDROM drivers.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* git://git.infradead.org/battery-2.6:
git-battery vs git-acpi
Power supply class and drivers: remove non obligatory return statements
pda_power: clean up irq, timer
MAINTAINERS: Add maintainers for power supply subsystem and drivers
Fixed up trivial conflict in drivers/w1/slaves/w1_ds2760.c manually
Add macvlan driver, which allows to create virtual ethernet devices
based on MAC address.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (149 commits)
USB: ohci-pnx4008: Remove unnecessary cast of return value of kzalloc
USB: additions to the quirk list
usb-storage: implement autosuspend
USB: cdc-acm: add new device id to option driver
USB: goku_udc trivial cleanups
USB: usb gadget stack can now -DDEBUG with Kconfig
usb gadget stack: remove usb_ep_*_buffer(), part 2
usb gadget stack: remove usb_ep_*_buffer(), part 1
USB: pxa2xx_udc -- cleanups, mostly removing dma hooks
USB: pxa2xx_udc: use generic gpio layer
USB: quirk for samsung printer
USB: usb/dma doc updates
USB: drivers/usb/storage/unusual_devs.h whitespace cleanup
USB: remove Makefile reference to obsolete OHCI_AT91
USB: io_*: remove bogus termios no change checks
USB: mos7720: remove bogus no termios change check
USB: visor and whiteheat: remove bogus termios change checks
USB: pl2303: remove bogus checks and fix speed support to use tty_get_baud_rate()
USB: mos7840.c: turn this into a serial driver
USB: make the usb_device numa_node get assigned from controller
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (76 commits)
IB: Update MAINTAINERS with Hal's new email address
IB/mlx4: Implement query SRQ
IB/mlx4: Implement query QP
IB/cm: Send no match if a SIDR REQ does not match a listen
IB/cm: Fix handling of duplicate SIDR REQs
IB/cm: cm_msgs.h should include ib_cm.h
IB/cm: Include HCA ACK delay in local ACK timeout
IB/cm: Use spin_lock_irq() instead of spin_lock_irqsave() when possible
IB/sa: Make sure SA queries use default P_Key
IPoIB: Recycle loopback skbs instead of freeing and reallocating
IB/mthca: Replace memset(<addr>, 0, PAGE_SIZE) with clear_page(<addr>)
IPoIB/cm: Fix warning if IPV6 is not enabled
IB/core: Take sizeof the correct pointer when calling kmalloc()
IB/ehca: Improve latency by unlocking after triggering the hardware
IB/ehca: Notify consumers of LID/PKEY/SM changes after nondisruptive events
IB/ehca: Return QP pointer in poll_cq()
IB/ehca: Change idr spinlocks into rwlocks
IB/ehca: Refactor sync between completions and destroy_cq using atomic_t
IB/ehca: Lock renaming, static initializers
IB/ehca: Report RDMA atomic attributes in query_qp()
...
Vojtech agreed to pass usblp over to me, so if you find bugs don't bug him.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (34 commits)
PCI: Only build PCI syscalls on architectures that want them
PCI: limit pci_get_bus_and_slot to domain 0
PCI: hotplug: acpiphp: avoid acpiphp "cannot get bridge info" PCI hotplug failure
PCI: hotplug: acpiphp: remove hot plug parameter write to PCI host bridge
PCI: hotplug: acpiphp: fix slot poweroff problem on systems without _PS3
PCI: hotplug: pciehp: wait for 1 second after power off slot
PCI: pci_set_power_state(): check for PM capabilities earlier
PCI: cpci_hotplug: Convert to use the kthread API
PCI: add pci_try_set_mwi
PCI: pcie: remove SPIN_LOCK_UNLOCKED
PCI: ROUND_UP macro cleanup in drivers/pci
PCI: remove pci_dac_dma_... APIs
PCI: pci-x-pci-express-read-control-interfaces cleanups
PCI: Fix typo in include/linux/pci.h
PCI: pci_ids, remove double or more empty lines
PCI: pci_ids, add atheros and 3com_2 vendors
PCI: pci_ids, reorder some entries
PCI: i386: traps, change VENDOR to DEVICE
PCI: ATM: lanai, change VENDOR to DEVICE
PCI: Change all drivers to use pci_device->revision
...
Change MAINTAINERS to formally take responsibility for the i386 boot code.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I'm no longer maintaining this driver as I no longer have the hardware
and I doubt anyone else does either.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (40 commits)
bonding/bond_main.c: make 2 functions static
ps3: gigabit ethernet driver for PS3, take3
[netdrvr] Fix dependencies for ax88796 ne2k clone driver
eHEA: Capability flag for DLPAR support
Remove sk98lin ethernet driver.
sunhme.c:quattro_pci_find() must be __devinit
bonding / ipv6: no addrconf for slaves separately from master
atl1: remove write-only var in tx handler
macmace: use "unsigned long flags;"
Cleanup usbnet_probe() return value handling
netxen: deinline and sparse fix
eeprom_93cx6: shorten pulse timing to match spec (bis)
phylib: Add Marvell 88E1112 phy id
phylib: cleanup marvell.c a bit
AX88796 network driver
IOC3: Switch to pci refcounting safe APIs
e100: Fix Tyan motherboard e100 not receiving IPMI commands
QE Ethernet driver writes to wrong register to mask interrupts
rrunner.c:rr_init() must be __devinit
tokenring/3c359.c:xl_init() must be __devinit
...
Hi,
This is the third submission of the network driver for PS3.
The differences from the previous one are:
- renamed source file names so that their prefix can match
with the module name
- added cbe-oss-dev@ozlabs.org line for MAINTAINER file
- changed some in copyright comments
If there are no more comments, please apply for 2.6.23.
Thank you
--
Subject: PS3: Ethernet driver
From: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Add Gigabit Ethernet support for the PS3 game console. The module will
be called ps3_gelic.
CC: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bryan is no longer with QLogic and we now have a public git server and
a public email alias for infinipath driver patches. And, as pointed
out by Hal Rosenstock, the mailing list has changed as well.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Most of the AGP changes recently have been done in lock-step with
DRM updates, so it's probably easier to have airlied pushing
AGP changes at the same time he does DRM updates.
[Also remove my name from the boot messages.
Cautionary tale to others: Never do this, when computers
don't boot, people assume you're responsible even if 15
other subsystems initialised after yours. :-) ]
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This patch adds a mac80211 based wireless driver for the rtl8187 USB
wireless card.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
davem kindly moved the list from osdl to vger.
Signed-of-by: maximilian attems <max@stro.at>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
>>>>> "Greg" == Greg KH <greg@kroah.com> writes:
Greg> Yeah, this is the cdc_acm driver that is still in the USB drivers/
Greg> directory tree as it is a USB class driver that shows up as a tty device
Greg> to userspace. It should not be moved to the networking list unless no
Greg> one minds that I never see any queries about it :)
Ok, here's an updated patch:
Questions regarding the USB network drivers should now go to netdev.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update ACPI Embedded Controller driver maintainer
with Alexey Starikovskiy's new e-mail address at Novell/SuSE.
Also, Alexey is taking over responsibility for the battery drivers.
Signed-off-by: Len Brown <len.brown@intel.com>
The UFS entry was misformatted
The NEC V850 links are all broken
The Berkshire watchdog links are all broken
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch changes MAINTAINERS to reflect the new location of the reiserfs
development mailing list. The old list forwards to the new one.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I've quit Intel and gone into business as a Linux consultant. Update
my email address in MAINTAINERS.
Signed-off-by: Valerie Henson <val@nmt.edu>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: Install firewire-constants.h and firewire-cdev.h for userspace.
firewire: Change struct fw_cdev_iso_packet to not use bitfields.
firewire: Implement suspend/resume PCI driver hooks.
firewire: add to MAINTAINERS
firewire: fw-sbp2: implement sysfs ieee1394_id
ieee1394: sbp2: offer SAM-conforming target port ID in sysfs
ieee1394: fix calculation of sysfs attribute "address"
We are seeing increasing levels of minor patch style violations in submissions
to the mailing lists as well as making it into the tree. These detract from
the quality of the submission and cause unnessary work for reviewers.
As a first step package up the current state of the patch style checker and
include it in the kernel tree. Add instructions suggesting running it on
submissions. This adds version v0.01 of the checkpatch.pl script.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Joel Schopp <jschopp@austin.ibm.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] megaraid_sas: intercept cmd timeout and throttle io
[SCSI] fusion: Fix |/|| confusion
[SCSI] aic94xx: asd_clear_nexus should fail if the cleared task does not complete
[SCSI] aic7xxx: fix aicasm build failure with gcc-3.4.6
[SCSI] aacraid: apply commit config for reset_devices flag
[SCSI] sd: fix refcounting regression in suspend/resume routines
[SCSI] aacraid: fix panic on short Inquiry
[SCSI] aacraid: Correct sa platform support. (Was: [Bug 8469] Bad EIP value on pentium3 SMP kernel-2.6.21.1)
[SCSI] NCR53C9x: correct spelling mistake in deprecation notice
[SCSI] tgt: fix a rdma indirect transfer error bug
[SCSI] MegaRAID: Update MAINTAINERS email-id
[SCSI] stex: minor cleanup and version update
[SCSI] stex: fix reset recovery for console device
[SCSI] stex: extend hard reset wait time
[SCSI] stex: fix id mapping issue
[SCSI] ipr: Proper return codes for eh_dev_reset for SATA devices
[SCSI] zfcp: IO stall after deleting and path checker changes after reenabling zfcp devices
[SCSI] zfcp: avoid clutter in erp_dbf
Pavel Pisa takes on the role of administrating this driver.
Signed-off-by: Pavel Pisa <ppisa@pikron.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Carlos Aguiar and Anderson Briglia are interested in making sure
the driver works for existing boards as they have access to them,
and Syed Khasim can make it work for new omaps (2430, 3430).
Signed-off-by: Syed Khasim <x0khasim@ti.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Most of the host controller drivers in the MMC layer lacks an
official maintainer. Make sure this is mentioned in MAINTAINERS
in case someone wants to pick up the ball.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This fixes the LDM driver so that it works with Windows Vista dynamic
disks which are subtly different to Windows 2000/XP ones.
The patch was needed to get a Vista formatted dynamic disk to be
recognized and parsed successfully.
Thanks go to Chris Teachworth for the report and testing.
Cc: Richard Russon <ldm@flatcap.org>
Signed-off-by: Anton Altaparmakov <aia21@cantab.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
linux-parport is subscribers-only:
Your mail to 'Linux-parport' with the subject
Re: [QUESTION] parallel console configuration
Is being held until the list moderator can review it for approval.
The reason it is being held:
Post by non-member to a members-only list
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update Maintainer email-id for MegaRAID SCSI drivers.
Signed-off-by: Sumant Patro <sumant.patro@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This reverts commit b6d1c9a447.
Others tell me that this address has worked for them, so I can only
assume that I hit a glitch in the sourceforge mail system.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Kylene Hall <kjhall@us.ibm.com>
Cc: Marcel Selhorst <tpm@selhorst.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I've not really 'maintained' this code for years, and others
are doing a much more thorough job these days.
Removing myself might stem some of the crazier emails I get.
Signed-off-by: Dave Jones <davej@redhat.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] MTX-1 Watchdog driver
[WATCHDOG] s3c2410_wdt - initialize watchdog irq resource
[WATCHDOG] Kconfig menuconfig patch
[WATCHDOG] pcwd.c: Port to the new device driver model
[WATCHDOG] use mutex instead of semaphore in Berkshire USB-PC Watchdog driver
[WATCHDOG] the scheduled removal of the i8xx_tco watchdog driver
[WATCHDOG] Semi-typical watchdog bug re early misc_register()
[WATCHDOG] add support for the w83627thf chipset.
* git://git.infradead.org/mtd-2.6: (21 commits)
[MTD] [CHIPS] Remove MTD_OBSOLETE_CHIPS (jedec, amd_flash, sharp)
[MTD] Delete allegedly obsolete "bank_size" field of mtd_info.
[MTD] Remove unnecessary user space check from mtd.h.
[MTD] [MAPS] Remove flash maps for no longer supported 405LP boards
[MTD] [MAPS] Fix missing printk() parameter in physmap_of.c MTD driver
[MTD] [NAND] platform NAND driver: add driver
[MTD] [NAND] platform NAND driver: update header
[JFFS2] Simplify and clean up jffs2_add_tn_to_tree() some more.
[JFFS2] Remove another bogus optimisation in jffs2_add_tn_to_tree()
[JFFS2] Remove broken insert_point optimisation in jffs2_add_tn_to_tree()
[JFFS2] Remember to calculate overlap on nodes which replace older nodes
[JFFS2] Don't advance c->wbuf_ofs to next eraseblock after wbuf flush
[MTD] [NAND] at91_nand.c: CMDLINE_PARTS support
[MTD] [NAND] Tidy up handling of page number in nand_block_bad()
[MTD] block2mtd_paramline[] mustn't be __initdata
[MTD] [NAND] Support multiple chips in CAFÉ driver
[MTD] [NAND] Rename cafe.c to cafe_nand.c and remove the multi-obj magic
[MTD] [NAND] Use rslib for CAFÉ ECC
[RSLIB] Support non-canonical GF representations
[JFFS2] Remove dead file histo_mips.h
...
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6: (32 commits)
Use menuconfig objects - hwmon
hwmon/smsc47b397: Use dynamic sysfs callbacks
hwmon/smsc47b397: Convert to a platform driver
hwmon/w83781d: Deprecate W83627HF support
hwmon/w83781d: Use dynamic sysfs callbacks
hwmon/w83781d: Be less i2c_client-centric
hwmon/w83781d: Clean up conversion macros
hwmon/w83781d: No longer use i2c-isa
hwmon/ams: Do not print error on systems without apple motion sensor
hwmon/ams: Fix I2C read retry logic
hwmon: New AD7416, AD7417 and AD7418 driver
hwmon/coretemp: Add documentation
hwmon: New coretemp driver
i386: Use functions from library in msr driver
i386: Add safe variants of rdmsr_on_cpu and wrmsr_on_cpu
hwmon/lm75: Use dynamic sysfs callbacks
hwmon/lm78: Use dynamic sysfs callbacks
hwmon/lm78: Be less i2c_client-centric
hwmon/lm78: No longer use i2c-isa
hwmon: New max6650 driver
...
There is a new list for kexec/kdump discussion.
Signed-off-by: Simon Horman <horms@verge.net.au>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver provides support for the Apple System Management Controller, which
provides an accelerometer (Apple Sudden Motion Sensor), light sensors,
temperature sensors, keyboard backlight control and fan control. Only
Intel-based Apple's computers are supported (MacBook Pro, MacBook, MacMini).
[bunk@stusta.de: make drivers/hwmon/applesmc.c:backlight_work stati]
[khali@linux-fr.org: fix temperature attribute file names]
Signed-off-by: Nicolas Boichat <nicolas@boichat.ch>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the support for the digital temperature sensor found in recent
Intel Core CPUs.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This driver supports the Maxim MAX6650 and MAX6651 fan speed
monitoring and control chips.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
