Shuffle Kconfig order, making the platform drivers menu depend on the global
option instead of each driver being dependent on it.
Also fix dependency of PPC_PMAC on the G5 one.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts commit 9414715a7b,
at Olaf Hering's request:
> Paul, please discard this patch. The optional graphics card may have
> also device_type 'serial' if it is in VGA mode.
> I will send an updated patch later.
check_legacy_ioport makes only sense on PREP, CHRP and pSeries.
They may have an isa node with PS/2, parport, floppy and serial ports.
Remove the check_legacy_ioport call from ppc_md, it's not needed
anymore. Hardware capabilities come from the device-tree.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cpufreq driver for PA Semi PWRficient processors.
Signed-off-by: Egor Martovetsky <egor@pasemi.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/platforms/pasemi/gpio_mdio.c really depends on CONFIG_PHYLIB.
Add a config option for it, allow for it to be disabled if needed and fix
the dependency.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/platforms/pasemi/setup.c: In function 'pasemi_publish_devices':
arch/powerpc/platforms/pasemi/setup.c:220: warning: implicit declaration of function 'of_platform_bus_probe'
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Replace uses with of_find_node_by_name and for_each_node_by_name.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is an old interface and is replaced by of_find_compatible_node.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rename MPIC_BROKEN_U3 to something a little more descriptive. Its
effect is to enable support for HT irqs behind the PCI-X/HT bridge on
U3/U4 (aka. CPC9x5) parts.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that we always take a device tree in arch/powerpc, there's no good
reason not to allow a single kernel to support multiple embedded 4xx
boards - the correct platform code can be selected based on the device
tree information.
Therefore, this patch re-arranges the 4xx Kconfig code to allow this.
In addition we:
- use "select" instead of depends to configure the correct
config options for specific 4xx CPUs and workarounds, which
makes the information about specific boards and CPUs less
scattered.
- Some old, unused (in arch/powerpc) config options are
removed: WANT_EARLY_SERIAL, IBM_OCP, etc.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
MDIO driver for PHY's connected via GPIO as on the PA Semi Electra
eval board.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Reset MPIC on boot to clear some timer state that firmware might
leave configured.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Device 0 function 0 on the root bus is really a two-function bus agent,
but only the first function is visible. Because of this, we need to
allow config accesses into the second range. Modify the check for valid
offsets accordingly.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Enable Periodic Recalibration (PTCAL) support for Cell XDR memory,
using the new ibm,cbe-start-ptcal and ibm,cbe-stop-ptcal RTAS calls.
Tested on QS20 and QS21 (by Thomas Huth). It seems that SLOF has
problems disabling, at least on QS20; this patch should only be
used once these problems have been addressed.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds support for a proper device-tree.
A porper device-tree on cell contains be nodes
for each CBE containg nodes for SPEs and all the
other special devices on it.
Ofcourse oldschool devicetree is still supported.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
The new PMI driver was added in order to support
cpufreq on blades that require the frequency to
be controlled by the service processor, so use it
on those.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds some attributes the cpu and spu nodes:
/sys/devices/system/[c|s]pu/[c|s]pu*/thermal/throttle_begin
/sys/devices/system/[c|s]pu/[c|s]pu*/thermal/throttle_end
/sys/devices/system/[c|s]pu/[c|s]pu*/thermal/throttle_full_stop
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch introduces a little function for transforming
register values into temperature.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds code to deal with conversion of
logical cpu to cbe nodes. It removes code that
assummed there were two logical CPUs per CBE.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This change fixes the case where spu_base and spufs are initialised on a
system with no SPEs - unconditionally create the spu_lists so spu_alloc
doesn't explode, and check for spu_management ops before starting spufs.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
arch/powerpc/platforms/cell/spu_base.c | 7 ++++---
arch/powerpc/platforms/cell/spufs/inode.c | 5 +++++
2 files changed, 9 insertions(+), 3 deletions(-)
spu_base.c is always built into the kernel image, so there is no need
for a cleanup function. And some of the things it does are in the
way for my following patches, so I'd rather get rid of it ASAP.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
- remove the spu_acquire_runnable from spu_run_init. I need to
opencode it in spufs_run_spu in the next patch
- remove various inline attributes, we don't really want to inline
long functions with multiple callsites
- cleanup return values and runcntl_write calls in spu_run_init
- use normal kernel codingstyle in spu_reacquire_runnable
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
spu_coredump_calls.owner is NULL in case of a builtin spufs,
so the checks in here break.
Check for the availability of the spu_coredump_calls variable
instead.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Dynamically allocated read/write buffer in spufs_arch_write_note() will
not be freed. Convert it to get_free_page at the same time.
Cc: Akinobu Mita <mita@fixstars.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Change the loop in spu_wait to be a little more straightforward.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Add a 'mode=' option to spufs mount arguments. This allows more
control over access to the top-level spufs directory.
Tested on Cell.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
GCC may generates inline copy loop to handle memcpy() function
instead of kernel defined memcpy(). But this inlined version of memcpy()
causes an alignment interrupt when copying from local store.
This patch uses memcpy_fromio() and memcpy_toio to copy local store
to prevent memcpy() being inlined.
Signed-off-by: Akinobu Mita <mita@fixstars.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
We now have proper locking around assignets of the mapping pointers,
and the spin_unlock implies enough of a barrier to get rid of the
explicit one.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
When SPU isolation mode enabled, isolated_loader would be
allocated by spufs_init_isolated_loader() on module_init().
But anyone do not free it.
This patch introduces spufs_exit_isolated_loader() which is
the opposite of spufs_init_isolated_loader() and called on
module_exit().
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Akinobu Mita <mita@fixstars.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
spufs module_init forgot to call a few cleanup functions
on error path. This patch also includes cosmetic changes in
spu_sched_init() (identation fix and return error code).
[modified by hch to apply ontop of the latest schedule changes]
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Akinobu Mita <mita@fixstars.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch checks return value of spu_acquire_runnable() in
spufs_mfc_write().
Signed-off-by: Akinobu Mita <mita@fixstars.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
There is no reason for run_sema to be a struct semaphore. Changing
it to a mutex and rename it accordingly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This change populates a siginfo struct for SPE application exceptions
(ie, invalid DMAs and illegal instructions).
Tested on an IBM Cell Blade.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Until now, we have always entered the spu page fault handler
with a mutex for the spu context held. This has multiple
bad side-effects:
- it becomes impossible to suspend the context during
page faults
- if an spu program attempts to access its own mmio
areas through DMA, we get an immediate livelock when
the nopage function tries to acquire the same mutex
This patch makes the page fault logic operate on a
struct spu_context instead of a struct spu, and moves it
from spu_base.c to a new file fault.c inside of spufs.
We now also need to copy the dar and dsisr contents
of the last fault into the saved context to have it
accessible in case we schedule out the context before
activating the page fault handler.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
There is no reason to execute spu_init_channels under spu_mutex
after the spu has been taken off the freelist it's ours.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Addition to stop_wq needs to happen before adding to the runqeueue and
under the same lock so that we don't have a race window for a lost
wake up in the spu scheduler.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
For quite a while now spu state is protected by a simple mutex instead
of the old rw_semaphore, and this means we can simplify the locking
around spu_setup_isolated a lot.
Instead of doing an spu_release before entering spu_setup_isolated and
then calling the complicated spu_acquire_exclusive we can now simply
enter the function locked an in guaranteed runnable state, so that the
only bit of spu_acquire_exclusive that's left is the call to
spu_unmap_mappings.
Similarly there's no more need to unlock and reacquire the state_mutex
when spu_setup_isolated is done, but we can always return with the
lock held and only drop it in spu_run_init in the failure case.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
A single context should only be woken once, and we should not have
more wakeups for a given priority than the number of contexts on
that runqueue position.
Also add some asserts to trap future problems in this area more
easily.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
set_bit does not guarantee ordering on powerpc, so using it
for communication between threads requires explicit
mb() calls.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
To not lose a spu thread we need to make sure it always gets put back
on the runqueue. In find_victim aswell as in the scheduler tick as done
in the previous patch.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
To not lose a spu thread we need to make sure it always gets put back
on the runqueue.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Make sure the pointers to various mappings are cleared once the last
user stopped using them. This avoids accessing freed memory when
tearing down the gang directory aswell as optimizing away
pte invalidations if no one uses these.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
The scheduler workqueue may rearm itself and deadlock when we try to stop
it. Put a flag in place to avoid skip the work if we're tearing down
the context.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
* Cleaned up some whitespace in arch/powerpc/Kconfig
* Moved sourcing of platforms/embedded6xx/Kconfig into platform/Kconfig
* Moved sourcing of platforms/4xx/Kconfig into platform/Kconfig and disabled it
* Removed EMBEDDEDBOOT since its not supported in arch/powerpc
* Removed PC_KEYBOARD since its not used anywhere
* Moved a few CONFIG options around in platform/Kconfig
* Moved interrupt controllers into platform/Kconfig out of bus section
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
