Add init declaration to cpu initialization functions.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
If SAL_CACHE_FLUSH drops interrupts, complain about it and fall back to
using PAL_CACHE_FLUSH instead.
This is to work around a defect in HP rx5670 firmware: when an interrupt
occurs during SAL_CACHE_FLUSH, SAL drops the interrupt but leaves it marked
"in-service", which leaves the interrupt (and others of equal or lower
priority) masked.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
On SN2, MMIO writes which are issued from separate processors are not
guaranteed to arrive in any particular order at the IO hardware. When
performing such writes from the kernel this is not a problem, as a
kernel thread will not migrate to another CPU during execution, and
mmiowb() calls can guarantee write ordering when control of the IO
resource is allowed to move between threads.
However, when MMIO writes can be performed from user space (e.g. DRM)
there are no such guarantees and mechanisms, as the process may
context-switch at any time, and may migrate to a different CPU as part
of the switch. For such programs/hardware to operate correctly, it is
required that the MMIO writes from the old CPU be accepted by the IO
hardware before subsequent writes from the new CPU can be issued.
The following patch implements this behavior on SN2 by waiting for a
Shub register to indicate that these writes have been accepted. This
is placed in the context switch-in path, and only performs the wait
when the newly scheduled task changes CPUs.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
There've been reports of problems with CONFIG_PREEMPT=y and the high
floating point partition. This is caused by the possibility of preemption
and rescheduling on a different processor while saving or restioirng the
high partition.
The only places where the FPU state is touched are in ptrace, in
switch_to(), and where handling a floating-point exception. In switch_to()
preemption is off. So it's only in trap.c and ptrace.c that we need to
prevent preemption.
Here is a patch that adds commentary to make the conditions clear, and adds
appropriate preempt_{en,dis}able() calls to make it so. In trap.c I use
preempt_enable_no_resched(), as we're about to return to user space where
the preemption flag will be checked anyway.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Version 3 - rediffed to apply on top of Ashok's hotplug cpu
patch. /proc/cpuinfo output in step with x86.
This is an updated MC/MT identification patch based on the
previous discussions on list.
Add the Multi-core and Multi-threading detection for IPF.
- Add new core and threading related fields in /proc/cpuinfo.
Physical id
Core id
Thread id
Siblings
- setup the cpu_core_map and cpu_sibling_map appropriately
- Handles Hot plug CPU
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Gordon Jin <gordon.jin@intel.com>
Signed-off-by: Rohit Seth <rohit.seth@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch introduces using the quicklists for pgd, pmd, and pte levels
by combining the alloc and free functions into a common set of routines.
This greatly simplifies the reading of this header file.
This patch is simple but necessary for large numa configurations.
It simply ensures that only pages from the local node are added to a
cpus quicklist. This prevents the trapping of pages on a remote nodes
quicklist by starting a process, touching a large number of pages to
fill pmd and pte entries, migrating to another node, and then unmapping
or exiting. With those conditions, the pages get trapped and if the
machine has more than 100 nodes of the same size, the calculation of
the pgtable high water mark will be larger than any single node so page
table cache flushing will never occur.
I ran lmbench lat_proc fork and lat_proc exec on a zx1 with and without
this patch and did not notice any change.
On an sn2 machine, there was a slight improvement which is possibly
due to pages from other nodes trapped on the test node before starting
the run. I did not investigate further.
This patch shrinks the quicklist based upon free memory on the node
instead of the high/low water marks. I have written it to enable
preemption periodically and recalculate the amount to shrink every time
we have freed enough pages that the quicklist size should have grown.
I rescan the nodes zones each pass because other processess may be
draining node memory at the same time as we are adding.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
There's only one usage of MM_VM_SIZE(mm) left, and it's a troublesome macro
because mm doesn't contain the (32-bit emulation?) info needed. But it too is
only needed because we ignore the end from the vma list.
We could make flush_pgtables return that end, or unmap_vmas. Choose the
latter, since it's a natural fit with unmap_mapping_range_vma needing to know
its restart addr. This does make more than minimal change, but if unmap_vmas
had returned the end before, this is how we'd have done it, rather than
storing the break_addr in zap_details.
unmap_vmas used to return count of vmas scanned, but that's just debug which
hasn't been useful in a while; and if we want the map_count 0 on exit check
back, it can easily come from the final remove_vm_struct loop.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
