Currently the Nomadik GPIO driver tracks enabled/disabled interrupt
status with a local variable, switch to using the interrupt core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The GPIO clock is required for register access and interrupt detection.
When interrupt detection is not required on any of the pin in a block,
the block's clock can be disabled when the registers are not being
accessed.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Rickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
[Adjust for new IRQ chip core code, use only local functions]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Building a kernel with hotplug disabled results in a link failure:
`bgpio_remove' referenced in section `___ksymtab_gpl+bgpio_remove' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
This is because of bgpio_remove() is exported. It is illegal to export
symbols which are discarded either at link time or as part of an
init/exit section.
Fix this by dropping the __devexit attributation from bgpio_remove().
Also drop the __devinit attributation from bgpio_init().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This rewrites the U300 GPIO so as to use gpiolib and
struct gpio_chip instead of just generic GPIO, hiding
all the platform specifics and passing in GPIO chip
variant as platform data at runtime instead of the
compiletime kludges.
As a result <mach/gpio.h> is now empty for U300 and
using just defaults.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Debian kernel maintainers <debian-kernel@lists.debian.org>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since commit 5093aec872
"arm: davinci: Cleanup irq chip code", the variable 'mask' and 'g'
are not being used.
This patch eliminate below unused variable warnings:
CC drivers/gpio/gpio-davinci.o
drivers/gpio/gpio-davinci.c: In function 'gpio_irq_type':
drivers/gpio/gpio-davinci.c:234: warning: unused variable 'mask'
drivers/gpio/gpio-davinci.c:233: warning: unused variable 'g'
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
irq_to_gpio is being removed. Replace the only use of that API by
the ARM Tegra sub-architecture.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure return value of irq_alloc_generic_chip() is checked before continuing
on to use it.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This macro is ugly and confusing, especially since it passes in most
arguments, but uses an implied 'base' from the caller.
Replace it with an equivalent static inline.
Signed-off-by: Kevin Hilman <khilman@ti.com>
As per example from the other ARM boards, push the SA100
GPIO driver down to the GPIO subsystem so it can be consolidated.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The <mach/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Barry Song <bs14@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per example from the other ARM boards, push the LPC32XX
GPIO driver down to the GPIO subsystem so it can be consolidated.
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Barry Song <bs14@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the ep93xx machine specific dependencies for gpio_to_irq() by
hooking up the callback in the driver and using __gpio_to_irq.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per example from the other ARM boards, push the DaVinci TNET
GPIO driver down to the GPIO subsystem so it can be consolidated.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per example from the other ARM boards, push the DaVinci GPIO
driver down to the GPIO subsystem so it can be consolidated.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The <mach/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.
Cc: zeal <zealcook@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: Daniel Silverstone <dsilvers@simtec.co.uk>
Acked-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per example from the other ARM boards, push the KS8695 GPIO
driver down to the GPIO subsystem so it can be consolidated.
Cc: zeal <zealcook@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: Daniel Silverstone <dsilvers@simtec.co.uk>
Acked-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The <mach/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The <[plat|mach]/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As irq_to_gpio() is only being used by gpio-mxs driver, it should be
moved from mach/gpio.h into gpio-mxs.c.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As irq_to_gpio() is only being used by gpio-mxc driver, it should be
moved from mach/gpio.h into gpio-mxc.c.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It adds .to_irq support for gpio chip, so that __gpio_to_irq in
gpiolib becomes usable.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Migrate the driver for the v7-based MSM chips into drivers/gpio. The
driver is unchanged, only moved.
Change-Id: I810db5b50b71cdca4e869aa0d0310f7f48781a55
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Migrate the driver for the v6-based MSM chips into drivers/gpio. The
driver is unchanged, only moved.
Change-Id: I03ba597b95b4d62b42da112a8efac88d67aa40f9
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
TPS65912 has five GPIOs that can be configured for different
purposes.
Signed-off-by: Margarita Olaya Cabrera <magi@slimlogic.co.uk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since 43cc71eed1 (platform: prefix MODALIAS
with "platform:"), the platform modalias is prefixed with "platform:".
This patch changes the MODULE_ALIAS to "platform:ab8500-gpio".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6: (61 commits)
gpio/mxc/mxs: fix build error introduced by the irq_gc_ack() renaming
mcp23s08: add i2c support
mcp23s08: isolate spi specific parts
mcp23s08: get rid of setup/teardown callbacks
gpio/tegra: dt: add binding for gpio polarity
mcp23s08: remove unused work queue
gpio/da9052: remove a redundant assignment for gpio->da9052
gpio/mxc: add device tree probe support
ARM: mxc: use ARCH_NR_GPIOS to define gpio number
gpio/mxc: get rid of the uses of cpu_is_mx()
gpio/mxc: add missing initialization of basic_mmio_gpio shadow variables
gpio: Move mpc5200 gpio driver to drivers/gpio
GPIO: DA9052 GPIO module v3
gpio/tegra: Use engineering names in DT compatible property
of/gpio: Add new method for getting gpios under different property names
gpio/dt: Refine GPIO device tree binding
gpio/ml-ioh: fix off-by-one for displaying variable i in dev_err
gpio/pca953x: Deprecate meaningless device-tree bindings
gpio/pca953x: Remove dynamic platform data pointer
gpio/pca953x: Fix IRQ support.
...
The following commit renames irq_gc_ack() to irq_gc_ack_set_bit(),
and makes gpio-mxc and gpio-mxs fail to build.
659fb32d1b
genirq: replace irq_gc_ack() with {set,clr}_bit variants (fwd)
The patch fixed a couple of typo of comma to semicolon.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add i2c bindings for the mcp230xx devices. This is quite a lot simpler
than the spi one as there's no funky sub addressing done (one struct
i2c_client per struct gpio_chip).
The mcp23s08_platform_data structure is reused for i2c, even though
only a single mcp23s08_chip_info structure is needed.
To use, simply fill out a platform_data structure and pass it in
i2c_board_info, E.G.:
static const struct mcp23s08_platform_data mcp23017_data = {
.chip[0] = {
.pullups = 0x00ff,
},
.base = 240,
};
static struct i2c_board_info __initdata i2c_devs[] = {
{ I2C_BOARD_INFO("mcp23017", 0x20),
.platform_data = &smartview_mcp23017_data, },
...
};
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Change spi member of struct mcp23s08 to be a ops-specific opaque data
pointer, and move spi specific knowledge out of mcp23s08_probe_one().
No functional change, but is needed to add i2c support.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
There's no in-tree users, and bus notifiers are more generic anyway.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The patch adds device tree probe support for gpio-mxc driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The patch removes all the uses of cpu_is_mx(). Instead, it utilizes
platform_device_id to distinguish the different gpio types, IMX1_GPIO
on i.mx1, IMX21_GPIO on i.mx21 and i.mx27, IMX31_GPIO on all other
i.mx SoCs.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The wrong bit was masked when acking langwell gpio interrupts.
Reason for maskig the wrong bit was probably because__ffs() and ffs() functions
return bit indexes differently (0..31 vs 1..32)
This fixes langwell based devices from hanging when a gpio interrupt is
triggered and undoes the breakage which occurred in change set
732063b92b
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The bgpio_init() function does not initialise the shadow register for
the GPIO direction register. Thus, when configuring the first GPIO with
gpio_set_direction() all other GPIOs of the same bank will be
configured as inputs. Since the bgpio layer cannot know whether the
register is readable, the initialisation should be done by the caller
of bgpio_init().
Also, the 'data' shadow variable that is used inside basic_mmio_gpio
to cache the current value of the GPIO_DR register is initialised from
the GPIO_PSR register within bgpio_init(). Thus when setting the
output value of a certain GPIO, the other GPIO outputs of the same
bank will be set or cleared depending on the pin state of the GPIO
inputs during bgpio_init().
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
GPIO drivers are getting consolidated into drivers/gpio. While at it,
change the driver name to mpc5200-gpio* to avoid collisions.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
DA9052 PMIC has 16 bit GPIO bus for peripheral control.
This patch add support for the GPIO pins on the DA9052.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Engineering names are more stable than marketing names. Hence, use them
for Device Tree compatible properties instead.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Many stupid corrections of duplicated includes based on the output of
scripts/checkincludes.pl.
Signed-off-by: Vitaliy Ivanov <vitalivanov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
with the "for (; i != 0; i--)" sytax, i-- will be executed after the iteration.
thus dev_err shows wrong i value.
Switch to "while(--i >= 0)" which is better in readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The property 'polarity' is handled by the GPIO core, and the 'gpio-base'
should be assigned automatically. It is meaningless in the device-tree,
since GPIO's are identified by the "chip-name"/offset pair.
This way, the whole pca953x_get_alt_pdata() can hopefully soon go away.
We still need to check whether we really want GPIO-interrupt functionality
by simply looking if the I2C node has an interrupts property defined, since
this property is not used for anything else.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
In the case that we obtain device-tree data to fill in platform_data, the new
platform data struct was dynamically allocated, but the pointer to it was not
used everywhere it should. It seems easier to fix this issue by removing the
dynamic allocation altogether since its data is only used during driver
probing.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It seems that in the normal case, IRQ_NOREQUEST needs to be explicitly
cleared, otherwise claiming the interrupt fails.
In the case of sparse interrupts, the descriptor needs to be allocated
first.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Remove cpu_is_* checks from gpio_show_revision() by passing in the
revision address offset from platform data. SoCs with no revision
register (15xx, 7xx, and all MPUIOs) use -1 (actually, USHRT_MAX) to
signify no register.
While here, all GPIO banks are assumed to be the same revision, so fix
show_revision() to only show the revision for the first bank it finds.
This removes duplicate GPIO revision prints during boot.
Thanks to Charulatha V <charu@ti.com> for finding/fixing a few -1s
that were missed in the original patch.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Make _set_gpio_wakeup() generic by removing ifdefs. Code for the
various SoCs/bank-methods was already the same, except for the
non-wakeup GPIO checking. But that flag is set on a per-SoC basis, so
can be used for all SoCs.
While here, use dev_err() and remove GPIO bank calculation assumption
based on subtracting bank pointers.
Signed-off-by: Kevin Hilman <khilman@ti.com>
These functions are useless. They are only called in a few places,
and where they are called, the GPIO has already been converted from an
IRQ or masked, so these functions will never fail.
Signed-off-by: Kevin Hilman <khilman@ti.com>
MPUIO banks have their own dedicated IRQ chip interface, separate from
the "normal" GPIO banks. Convert the MPUIO IRQ chip over to using
the new generic IRQ chip interface.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Cleanup GPIO IRQ enable/disable handling by removing SoC-specific
Also split enable/disable IRQ into separate functions for better
readability and also facilitate potentially moving to generic irq_chip
in the future.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Cleanup IRQ status handling by passing IRQ status register offsets
via platform data.
Cleans up clearing of GPIO IRQ status and GPIO ISR handler.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add register offset fields to GPIO platform_data for registers.
This patch adds registers that control direction, input and output
data. Using these register offsets in the common driver allows
removal of #ifdefs and greatly improves readability.
Also create dedicated data out functions: one for banks with dedicated
set/clear registers, and another for banks with a single mask
register.
Signed-off-by: Kevin Hilman <khilman@ti.com>
The get_gpio_index() function, littered with cpu_is_* checks can be easily
replaced by using bitops based on the GPIO bank width. Do so.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Rather than having a file-global bank_width variable, move it into
struct gpio_bank so it can be bank-specific. Note the bank width
is already passed per-bank via platform_data, so current code would
be incorrect if any banks had different width.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove the OMAP1 #ifdef and MPUIO special case for _clear_gpio_irqbank()
The MPUIOs do not need a register access to ack/clear the IRQ status,
since reading the IRQ status clears it. In addition, the MPUIO
irq_chip has an empty ack method, so _clear_gpio_irqbank() is never
used for MPUIOs.
Signed-off-by: Kevin Hilman <khilman@ti.com>
In commit 78a1a6d341 (ARM: OMAP4: Update
the GPIO support) braces were mistakenly added to included the
register read-back inside the cpu_is_* checking.
Remove the braces, ensuring that a register read-back is done, even
when the IRQSTATUS2 register is not written.
Note that the register read-back might be IRQSTATUS1 or IRQSTATUS2
depending on the CPU, but a read-back of any register in that region
will cause a flush of the posted writes.
Signed-off-by: Kevin Hilman <khilman@ti.com>
If gpio pins from bank[2-5] are marked as wakeup enable and if the wake is
through gpio IO pad wakeup, then that wakeup gpio interrupt is lost.
In the current implementation, GPIO driver stores the context of DATAIN of
all the gpio in the bank. During GPIO resuming, it checks DATAIN with wakeup
enabled pins of gpio bank. If there is status change, then manually toggle
GPIO_LEVELDETECT to generate pseudo interrupt.
Reported-by: Philippe Mazet <p-mazet@ti.com>
Tested-by: Philippe Mazet <p-mazet@ti.com>
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
As part of the gpio driver consolidation, this patch moves the Tegra driver
into drivers/gpio
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Colin Cross <ccross@android.com>
The 74x164 GPIO driver has a static inline helper called
gpio_to_chip which clashes with the gpiolib namespace if we
try to expose the function with the same name from gpiolib,
and it's still confusing even if we don't do that. So rename
it to gpio_to_74x164_chip().
Reported-by: H Hartley Sweeten <hartleys@visionengravers.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When calling gpio_get_value, the gpio number other than bit offset
should be passed as the argument.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Remove miscellaneous use of direct calculation by using resource_size().
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The mach-nomadik machine did not compile properly due to bad
ux500-specific functions being called. Introduce new state
variables to fix this up.
Reported-by: Axel Lin <axel.lin@gmail.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Prafulla Wadaskar <prafulla.wadaskar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This converts the gpio-ep93xx driver into a platform_driver and uses
the basic_mmio_gpio library.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When using nested threaded irqs, use handle_nested_irq(). This function
does not call the chip handler, so no handler is set.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The interrupt pin of the PCA953x is active low, and on the rising edge
no interrupt should be produced.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It seems that in the normal case, IRQ_NOREQUEST needs to be explicitly
cleared, otherwise claiming the interrupt fails.
In the case of sparse interrupts, the descriptor needs to be allocated
first.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
With this driver now being moved from arch/arm/mach-ep93xx/gpio.c to
drivers/gpio/gpio-ep93xx.c the prefix "ep93xx" is now redundant in the
pr_* output. Using KBUILD_MODNAME is sufficient.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The Samsung GPIO drivers are always built-in when the relevant
platform is selected. Change the Kconfig symbol to def_bool y
dependant on the platform.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The S3C_GPIO_PULL_UP macro value incorrectly maps to a reserved setting of GPIO
pull up/down registers on Exynos4 platform. Fix this incorrect mapping by adding
wrappers to the s3c_gpio_setpull_updown and s3c_gpio_getpull_updown functions.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The patch converts gpio-mxs driver to use generic irq chip.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The irq_high stuff was mistakenly copied from mxc gpio driver.
The mxs gpio controller has only one irq line for each 32-pin
gpio port. The patch remove irq_high related codes.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The gpio-mxs controller complies with basic_mmio_gpio library. This
patch converts the driver to use the library.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
_set_gpio_triggering uses read-modify-write on bank registers,
lock bank->lock around all calls to it to prevent register
corruption if two cpus access gpios in the same bank at the
same time.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Setting the IRQWAKEN bit was overwriting previous IRQWAKEN bits,
causing only the last bit set to take effect, resulting in lost
wakeups when the GPIO controller is in idle.
Replace direct writes to IRQWAKEN with MOD_REG_BIT calls to
perform a read-modify-write on the register.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
WARNING: arch/arm/plat-omap/built-in.o(.devinit.text+0x46c): Section mismatch in reference from the function omap_gpio_probe() to the function .init.text:omap_gpio_chip_init()
The function __devinit omap_gpio_probe() references
a function __init omap_gpio_chip_init().
If omap_gpio_chip_init is only used by omap_gpio_probe then
annotate omap_gpio_chip_init with a matching annotation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Sort the gpio makefile and enforce the naming convention gpio-*.c for
gpio drivers.
v2: cleaned up filenames in Kconfig and comment blocks
v3: fixup use of BASIC_MMIO to GENERIC_GPIO for mxc
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The interrupt pin of the PCA953x is active low, and on the rising edge
no interrupt should be produced.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The GPIO driver should reside in drivers/gpio.
v3: Change Kconfig option to def_bool y
v2: Make the Kconfig symbol a silent option, dependent on ARCH_EP93XX
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The gpio-mxc controller complies with basic_mmio_gpio library. The
patch convert the driver to use the library.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The patch makes necessary changes on gpio-mxc as below to turn it
into an upstanding gpio driver.
* Add a list to save all mx2 ports references, so that
mx2_gpio_irq_handler can walk through all interrupt status
registers
* Use readl/writel to replace mach-specific accessors
__raw_readl/__raw_writel
* Change mxc_gpio_init into mxc_gpio_probe function
* Move "struct mxc_gpio_port" into gpio-mxc.c, as it needs not to
be public at all, and also make some other cleanup on
plat-mxc/include/mach/gpio.h at the same time
And the patch then migrates mach-imx and mach-mx5 to the updated
driver by adding corresponding platform devices.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
GPIO drivers are getting moved to drivers/gpio for cleanup and
consolidation. This patch moves the plat-mxc driver. Follow up
patches will clean it up and make it a fine upstanding gpio driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The patch makes necessary changes on gpio-mxs as below to turn it
into an upstanding gpio driver.
* Clean up the gpio port definition stuff
* Use readl/writel to replace mach-specific accessors
__raw_readl/__raw_writel
* Change mxs_gpio_init into mxs_gpio_probe function
And it then migrates mach-mxs to the updated driver by adding
corresponding platform devices.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
GPIO drivers are getting moved to drivers/gpio for cleanup and
consolidation. This patch moves the mxs driver. Follow up patches
will clean it up and make it a fine upstanding example of a gpio
driver.
v2: Removed header file entirely and put struct definition directly
into driver. The struct isn't used anywhere else in the kernel.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
The Samsung GPIO drivers are always built-in when the relevant
platform is selected. Change the Kconfig symbol to def_bool y
dependant on the platform.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Remove the #define GEN_74X164_GPIO_COUNT since it's only used in
one place and it's meaning is obvious. Also remove the #define
GEN_74X164_DRIVER_NAME and use spi->modalias to set the gpio chip's
label and the string "74x164" for the driver name.
Reorder the code slightly to remove the need to prototype
gen_74x164_set_value.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
After the GPIO driver move, some symbols became selectable when they
shouldn't be. Tighten the dependencies.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We had a few drivers move from arch/arm into drivers/gpio, but they
don't actually compile without the ARM platform headers etc. As a
result they were messing up allyesconfig on x86.
Make them depend on ARM.
Reported-by: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6:
gpio/pch_gpio: Support new device ML7223
gpio: make gpio_{request,free}_array gpio array parameter const
GPIO: OMAP: move to drivers/gpio
GPIO: OMAP: move register offset defines into <plat/gpio.h>
gpio: Convert gpio_is_valid to return bool
gpio: Move the s5pc100 GPIO to drivers/gpio
gpio: Move the s5pv210 GPIO to drivers/gpio
gpio: Move the exynos4 GPIO to drivers/gpio
gpio: Move to Samsung common GPIO library to drivers/gpio
gpio/nomadik: add function to read GPIO pull down status
gpio/nomadik: show all pins in debug
gpio: move Nomadik GPIO driver to drivers/gpio
gpio: move U300 GPIO driver to drivers/gpio
langwell_gpio: add runtime pm support
gpio/pca953x: Add support for pca9574 and pca9575 devices
gpio/cs5535: Show explicit dependency between gpio_cs5535 and mfd_cs5535
Support new device OKI SEMICONDUCTOR ML7223 IOH(Input/Output Hub).
The ML7223 IOH is for MP(Media Phone) use.
The ML7223 is companion chip for Intel Atom E6xx series.
The ML7223 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
gpio_{request,free}_array should not (and do not) modify the passed gpio
array, so make the parameter const.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
GPIO 1 to 8 are added for TPS65911 chip version. The gpio driver
now handles more than one gpio lines. Subsequent versions of the
chip family can add new GPIO lines with minimal driver changes.
Signed-off-by: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The GPIO driver should reside in drivers/gpio/ for better
organization.
Signed-off-by: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Move the Samsung s5pc100 SoC GPIO driver to drivers/gpio
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Move the Samsung s5pv210 SoC GPIO driver to drivers/gpio
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Move the Samsung Exynos4 series SoCs GPIO driver to drivers/gpio
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It's common gpiolib for recent Samsung SoCs. Move to drivers/gpio
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Useful to check the status of the runtime pin muxing.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
[Squashed, modified to use chip-internal IRQ trigger state]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This moves the Nomadik GPIO driver out of arch/arm/plat-nomadik
and into the desired location indicated by the subsystem
maintainer.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[grant.likely: squashed with kconfig fixup]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This moves the U300 GPIO driver out of arch/arm/mach-u300 and into
the desired location indicated by the subsystem maintainer.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
While this is essentially a no-op for this driver, it has the
side effect of letting the PMU driver snoop D3 requests from
the PCI core for this driver.
This is only for langwell, not for whitney point.
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
PCA957x is i2c gpio expander, and similar to PCA953x. Although register
configurations are different between PCA957x and PCA953x. They can share
a lot of components, such as IRQ handling, GPIO IN/OUT. So updating PCA953x
driver to support PCA957x chips.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
cs5535-gpio.c has been split into two, with various setup moved
into cs5535-mfd.c. Given that cs5535-gpio will not load without
the -mfd part, lets make that dependency explicit in Kconfig
Signed-off-by: Ed Wildgoose <kernel@wildgooses.com>
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6:
gpio/via: rename VIA local config struct
basic_mmio_gpio: split into a gpio library and platform device
gpio: remove some legacy comments in build files
gpio: add trace events for setting direction and value
gpio/pca953x: Use handle_simple_irq instead of handle_edge_irq
gpiolib: export gpiochip_find
gpio: remove redundant Kconfig depends on GPIOLIB
basic_mmio_gpio: convert to non-__raw* accessors
basic_mmio_gpio: support direction registers
basic_mmio_gpio: support different input/output registers
basic_mmio_gpio: detect output method at probe time
basic_mmio_gpio: request register regions
basic_mmio_gpio: allow overriding number of gpio
basic_mmio_gpio: convert to platform_{get,set}_drvdata()
basic_mmio_gpio: remove runtime width/endianness evaluation
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With the addition of a device platform mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Acked-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
alpha allmodconfig:
drivers/gpio/ml_ioh_gpio.c: In function 'ioh_gpio_probe':
drivers/gpio/ml_ioh_gpio.c:205: error: implicit declaration of function 'kzalloc'
drivers/gpio/ml_ioh_gpio.c:205: warning: assignment makes pointer from integer without a cast
also fix this:
drivers/gpio/ml_ioh_gpio.c:145: warning: 'ioh_gpio_save_reg_conf' defined but not used
drivers/gpio/ml_ioh_gpio.c:154: warning: 'ioh_gpio_restore_reg_conf' defined but not used
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
alpha allmodconfig:
drivers/gpio/vx855_gpio.c: In function 'vx855gpio_probe':
drivers/gpio/vx855_gpio.c:233: error: implicit declaration of function 'kzalloc'
drivers/gpio/vx855_gpio.c:233: warning: assignment makes pointer from integer without a cast
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow GPIO_BASIC_MMIO_CORE to be used to provide an accessor library
for implementing GPIO drivers whilst abstracting the register access
detail. Based on a patch from Anton Vorontsov[1] and adapted to allow
bgpio_chip to be embedded in another structure.
Changes since v1:
- Register the gpio_chip in the platform device probe
1. https://lkml.org/lkml/2011/4/19/401
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The build files for drivers/gpio has some wording and comments
about the directory being reserved exclusively for GPIO expanders
(according to the gpio.txt file these are on external busses) and
this has been false for some time. We already have PL061 and
Xilinx drivers which are in silicon and now I'm moving more
silicon drivers here, so delete this and reword it a bit.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch allows to trace gpio operations using ftrace
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Make pca953x driver use the simple irq handler since no hardware control
is necessary and the driver lacks an irq_ack function. handle_edge_irq()
calls chip->irq_ack() which crashes since this function does not exist.
Signed-off-by: Erik Botö <erik.boto@pelagicore.com>
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Export function gpiochip_find so that modules can use it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Since all the drivers are in a 'if GPIOLIB/endif block', the depends on GPIOLIB
is redundant so remove them.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The __raw_* accessors don't include memory barriers and can cause
problems when writes get stuck in write buffers.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Most controllers require the direction of a GPIO to be set by writing to
a direction register. Add support for either an input direction
register or an output direction register.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Some controllers have separate input and output registers. For these
controllers, use "set" for the output and "dat" for the input.
Changes since v2: reuse "set" for output and "dat" for input rather than
adding a new "in" register.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Rather than detecting the output method each time in the .set()
callback, do it at probe time and set the appropriate callback.
Changes since v2: moved the reg_dat initialization into
bgpio_setup_io().
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Make sure that we get the register regions with request_mem_region()
before ioremap() to make sure we have exclusive access.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Some platforms may have a number of GPIO that is less than the register
width of the peripheral.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Use the platform drvdata helpers rather than working on the struct
device itself.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Remove endianness/width calculations at runtime by installing function
pointers for bit-to-mask conversion and register accessors.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Using C line continuation inside format strings is error prone.
Clean up the unintended whitespace introduced by misuse of \.
Neaten correctly used line continations as well for consistency.
drivers/scsi/arcmsr/arcmsr_hba.c has these errors as well,
but arcmsr needs a lot more work and the driver should likely be
moved to staging instead.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
