Make sure we enable the clock before leaving probe.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'spi/next' of git://git.secretlab.ca/git/linux-2.6:
drivercore: Add helper macro for platform_driver boilerplate
spi: irq: Remove IRQF_DISABLED
OMAP: SPI: Fix the trying to free nonexistent resource error
spi/spi-ep93xx: add module.h include
spi/tegra: fix compilation error in spi-tegra.c
spi: spi-dw: fix all sparse warnings
spi/spi-pl022: Call pl022_dma_remove(pl022) only if enable_dma is true
spi/spi-pl022: calculate_effective_freq() must set rate <= requested rate
spi/spi-pl022: Don't allocate more sg than required.
spi/spi-pl022: Use GFP_ATOMIC for allocation from tasklet
spi/spi-pl022: Resolve formatting issues
This patch fixes a build error, introduced by commit (67fc8b9f, "PM: add
runtime PM support to core Primecell driver") which unfortunately was a little
bit incomplete and did contain a typo (11 instead of 22).
I'm not sure how this patch could have been tested back then, if it
doesn't even compile ;)
The build failure was:
drivers/spi/spi-pl022.c:2292: error: 'adev' undeclared (first use in
this function)
drivers/spi/spi-pl022.c:2344: error: 'pl022_suspend' undeclared here
(not in a function)
The build failure appears e.g. for the u8500 and realview defconfig.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add runtime PM support to the core Primecell driver, following the PCI
model of how this is done.
Rather than having every driver fiddle about with enabling runtime PM,
that's dealt with in the core and instead, drivers just do a put() in
their probe and a balancing get() in their remove function to activate
runtime PM for the device.
As we're dealing with enabling runtime PM in the core, fix up spi-pl022
as it must not enable and disable runtime PM itself anymore.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pl022_dma_remove() should be called only if enable_dma is true. There is no
point calling it when pl022_dma_probe() is not called, which again depends on
enable_dma.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
There were few issues with calculate_effective_freq() routine:
- It was returning first rate found >= requested rate. Now, if system have spi's
rate as 83 MHz, with possible prescaled rates as 83, 41.5, 20.75, 13.83 (as we
can prescale with multiples of 2). If user has given rate to be programmed as
22 MHz, then driver programmes it to 41.5 MHz. This looks to be incorrect, as
user might have given the upper limit of the device, and we are programming it
above it.
- Driver finds the first satisfying rate and programmes it, but with other
values of scr & cpsdvsr, it is possible to get more closer rate.
This patch fixes these two issues, with some reformatting inside the code. This
also creates a inline routine to calculate prescaled rate based on spi's rate,
cpsdvsr and scr.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
In routine configure_dma(), if transfer->len = PAGE_SIZE, then pages is one more
than required. While leads to one more sg getting allocated.
This is wrong. Correct this to allocate correct number of sg.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
tasklets don't allow invocation to sleeping routines. In configure_dma()
routine, sg_alloc_table() was called with GFP_KERNEL flag and so this causes
crash when called from tasklet.
Replace GFP_KERNEL with GFP_ATOMIC to get this fixed.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
There were few formatting related issues in code. This patch fixes them.
Fixes include:
- Remove extra blank lines
- align code to 80 cols
- combine several lines to one line
- Replace multiple spaces with tabs
- Remove spaces before labels
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The remove function in the PL022 driver cannot abort the remove
function any way, so restructure the code so as not to make that
assumption. Remove will now proceed no matter whether it can
stop the transfer queue or not.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The platform configuration can select custom FIFO watermarks, but
these may conflict the actual FIFO size of the PL022 variant if
set too high. So strengthen the sanity checks to deny any
conflicting settings.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Insert notifiers for the runtime PM API. With this the runtime
PM layer kicks in to action where used.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
[Rebased to Linux 3.0-rc3, edit description]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Configure the DMA burstsize from the FIFO trigger level supplied
with the controller configuration data. This is based on a patch
from Virupax, but I rewrote it differently.
Reported-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Sort the SPI makefile and enforce the naming convention spi_*.c for
spi drivers.
This change also rolls the contents of atmel_spi.h into the .c file
since there is only one user of that particular include file.
v2: - Use 'spi-' prefix instead of 'spi_' to match what seems to be
be the predominant pattern for subsystem prefixes.
- Clean up filenames in Kconfig and header comment blocks
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
