The linearisation operation doesn't need to be super-optimised. So we can
replace __skb_linearize with __pskb_pull_tail which does the same thing but
is more general.
Also, most users of skb_linearize end up testing whether the skb is linear
or not so it helps to make skb_linearize do just that.
Some callers of skb_linearize also use it to copy cloned data, so it's
useful to have a new function skb_linearize_cow to copy the data if it's
either non-linear or cloned.
Last but not least, I've removed the gfp argument since nobody uses it
anymore. If it's ever needed we can easily add it back.
Misc bugs fixed by this patch:
* via-velocity error handling (also, no SG => no frags)
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Various drivers use xmit_lock internally to synchronise with their
transmission routines. They do so without setting xmit_lock_owner.
This is fine as long as netpoll is not in use.
With netpoll it is possible for deadlocks to occur if xmit_lock_owner
isn't set. This is because if a printk occurs while xmit_lock is held
and xmit_lock_owner is not set can cause netpoll to attempt to take
xmit_lock recursively.
While it is possible to resolve this by getting netpoll to use
trylock, it is suboptimal because netpoll's sole objective is to
maximise the chance of getting the printk out on the wire. So
delaying or dropping the message is to be avoided as much as possible.
So the only alternative is to always set xmit_lock_owner. The
following patch does this by introducing the netif_tx_lock family of
functions that take care of setting/unsetting xmit_lock_owner.
I renamed xmit_lock to _xmit_lock to indicate that it should not be
used directly. I didn't provide irq versions of the netif_tx_lock
functions since xmit_lock is meant to be a BH-disabling lock.
This is pretty much a straight text substitution except for a small
bug fix in winbond. It currently uses
netif_stop_queue/spin_unlock_wait to stop transmission. This is
unsafe as an IRQ can potentially wake up the queue. So it is safer to
use netif_tx_disable.
The hamradio bits used spin_lock_irq but it is unnecessary as
xmit_lock must never be taken in an IRQ handler.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a secmark field to the skbuff structure, to allow security subsystems to
place security markings on network packets. This is similar to the nfmark
field, except is intended for implementing security policy, rather than than
networking policy.
This patch was already acked in principle by Dave Miller.
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Any socket recv of less than this ammount will not be offloaded
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds an async_wait_queue and some additional fields to tcp_sock, and a
dma_cookie_t to sk_buff.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provides for pinning user space pages in memory, copying to iovecs,
and copying from sk_buffs including fragmented and chained sk_buffs.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attempts to allocate per-CPU DMA channels
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Noticed that dev_alloc_name() comment was incorrect, and more spellung
errors.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The classical IP over ATM code maintains its own IPv4 <-> <ATM stuff>
ARP table, using the standard neighbour-table code. The
neigh_table_init function adds this neighbour table to a linked list
of all neighbor tables which is used by the functions neigh_delete()
neigh_add() and neightbl_set(), all called by the netlink code.
Once the ATM neighbour table is added to the list, there are two
tables with family == AF_INET there, and ARP entries sent via netlink
go into the first table with matching family. This is indeterminate
and often wrong.
To see the bug, on a kernel with CLIP enabled, create a standard IPv4
ARP entry by pinging an unused address on a local subnet. Then attempt
to complete that entry by doing
ip neigh replace <ip address> lladdr <some mac address> nud reachable
Looking at the ARP tables by using
ip neigh show
will reveal two ARP entries for the same address. One of these can be
found in /proc/net/arp, and the other in /proc/net/atm/arp.
This patch adds a new function, neigh_table_init_no_netlink() which
does everything the neigh_table_init() does, except add the table to
the netlink all-arp-tables chain. In addition neigh_table_init() has a
check that all tables on the chain have a distinct address family.
The init call in clip.c is changed to call
neigh_table_init_no_netlink().
Since ATM ARP tables are rather more complicated than can currently be
handled by the available rtattrs in the netlink protocol, no
functionality is lost by this patch, and non-ATM ARP manipulation via
netlink is rescued. A more complete solution would involve a rtattr
for ATM ARP entries and some way for the netlink code to give
neigh_add and friends more information than just address family with
which to find the correct ARP table.
[ I've changed the assertion checking in neigh_table_init() to not
use BUG_ON() while holding neigh_tbl_lock. Instead we remember that
we found an existing tbl with the same family, and after dropping
the lock we'll give a diagnostic kernel log message and a stack dump.
-DaveM ]
Signed-off-by: Simon Kelley <simon@thekelleys.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last step of netdevice registration was being done by a delayed
call, but because it was delayed, it was impossible to return any error
code if the class_device registration failed.
Side effects:
* one state in registration process is unnecessary.
* register_netdevice can sleep inside class_device registration/hotplug
* code in netdev_run_todo only does unregistration so it is simpler.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test used in the linkwatch does not handle wrap-arounds correctly.
Since the intention of the code is to eliminate bursts of messages we
can afford to delay things up to a second. Using that fact we can
easily handle wrap-arounds by making sure that we don't delay things
by more than one second.
This is based on diagnosis and a patch by Stefan Rompf.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Stefan Rompf <stefan@loplof.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Alan Stern <stern@rowland.harvard.edu>
This chain does it's own locking via the RTNL semaphore, and
can also run recursively so adding a new mutex here was causing
deadlocks.
Signed-off-by: David S. Miller <davem@davemloft.net>
Atomically create attributes when class device is added. This avoids
the race between registering class_device (which generates hotplug
event), and the creation of attribute groups.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some sanity checking. truesize should be at least sizeof(struct
sk_buff) plus the current packet length. If not, then truesize is
seriously mangled and deserves a kernel log message.
Currently we'll do the check for release of stream socket buffers.
But we can add checks to more spots over time.
Incorporating ideas from Herbert Xu.
Signed-off-by: David S. Miller <davem@davemloft.net>
I've just realised that the RtNetlink code does not check the
permission for SIOCGIWENCODE and SIOCGIWENCODEEXT, which means that
any user can read the encryption keys. The fix is trivial and should
go in 2.6.17 alonside the two other patch I sent you last week.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check the permissions when user-space try to read the
encryption parameters via SIOCGIWENCODEEXT. This is trivial and
probably should go in 2.6.17...
Bug was found by Brian Eaton <eaton.lists@gmail.com>, thanks !
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes unaligned access warnings noticed on IA64
in sk_run_filter(). 'ptr' can be unaligned.
Signed-off-By: Dmitry Mishin <dim@openvz.org>
Signed-off-By: Kirill Korotaev <dev@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
for_each_cpu() actually iterates across all possible CPUs. We've had mistakes
in the past where people were using for_each_cpu() where they should have been
iterating across only online or present CPUs. This is inefficient and
possibly buggy.
We're renaming for_each_cpu() to for_each_possible_cpu() to avoid this in the
future.
This patch replaces for_each_cpu with for_each_possible_cpu under /net
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Thomas de Grenier de Latour <degrenier@easyconnect.fr>
On Sun, 9 Apr 2006 21:56:59 +0400,
Sergey Vlasov <vsu@altlinux.ru> wrote:
> However, show_address() does not output anything unless
> dev->reg_state == NETREG_REGISTERED - and this state is set by
> netdev_run_todo() only after netdev_register_sysfs() returns, so in
> the meantime (while netdev_register_sysfs() is busy adding the
> "statistics" attribute group) some process may see an empty "address"
> attribute.
I've tried the attached patch, suggested by Sergey Vlasov on
hotplug-devel@, and as far as i can test it works just fine.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an off-by-21-or-49 error ;-) spotted by the Coverity
checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put a comment in there explaining why we double the setsockopt()
caller's SO_RCVBUF. People keep wondering.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On a allyesconfig'ured kernel:
Size Uses Wasted Name and definition
===== ==== ====== ================================================
95 162 12075 netif_wake_queue include/linux/netdevice.h
129 86 9265 dev_kfree_skb_any include/linux/netdevice.h
127 56 5885 netif_device_attach include/linux/netdevice.h
73 86 4505 dev_kfree_skb_irq include/linux/netdevice.h
46 60 1534 netif_device_detach include/linux/netdevice.h
119 16 1485 __netif_rx_schedule include/linux/netdevice.h
143 5 492 netif_rx_schedule include/linux/netdevice.h
81 7 366 netif_schedule include/linux/netdevice.h
netif_wake_queue is big because __netif_schedule is a big inline:
static inline void __netif_schedule(struct net_device *dev)
{
if (!test_and_set_bit(__LINK_STATE_SCHED, &dev->state)) {
unsigned long flags;
struct softnet_data *sd;
local_irq_save(flags);
sd = &__get_cpu_var(softnet_data);
dev->next_sched = sd->output_queue;
sd->output_queue = dev;
raise_softirq_irqoff(NET_TX_SOFTIRQ);
local_irq_restore(flags);
}
}
static inline void netif_wake_queue(struct net_device *dev)
{
#ifdef CONFIG_NETPOLL_TRAP
if (netpoll_trap())
return;
#endif
if (test_and_clear_bit(__LINK_STATE_XOFF, &dev->state))
__netif_schedule(dev);
}
By de-inlining __netif_schedule we are saving a lot of text
at each callsite of netif_wake_queue and netif_schedule.
__netif_rx_schedule is also big, and it makes more sense to keep
both of them out of line.
Patch also deinlines dev_kfree_skb_any. We can deinline dev_kfree_skb_irq
instead... oh well.
netif_device_attach/detach are not hot paths, we can deinline them too.
Signed-off-by: Denis Vlasenko <vda@ilport.com.ua>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NET]: drop duplicate assignment in request_sock
[IPSEC]: Fix tunnel error handling in ipcomp6
The kernel's implementation of notifier chains is unsafe. There is no
protection against entries being added to or removed from a chain while the
chain is in use. The issues were discussed in this thread:
http://marc.theaimsgroup.com/?l=linux-kernel&m=113018709002036&w=2
We noticed that notifier chains in the kernel fall into two basic usage
classes:
"Blocking" chains are always called from a process context
and the callout routines are allowed to sleep;
"Atomic" chains can be called from an atomic context and
the callout routines are not allowed to sleep.
We decided to codify this distinction and make it part of the API. Therefore
this set of patches introduces three new, parallel APIs: one for blocking
notifiers, one for atomic notifiers, and one for "raw" notifiers (which is
really just the old API under a new name). New kinds of data structures are
used for the heads of the chains, and new routines are defined for
registration, unregistration, and calling a chain. The three APIs are
explained in include/linux/notifier.h and their implementation is in
kernel/sys.c.
With atomic and blocking chains, the implementation guarantees that the chain
links will not be corrupted and that chain callers will not get messed up by
entries being added or removed. For raw chains the implementation provides no
guarantees at all; users of this API must provide their own protections. (The
idea was that situations may come up where the assumptions of the atomic and
blocking APIs are not appropriate, so it should be possible for users to
handle these things in their own way.)
There are some limitations, which should not be too hard to live with. For
atomic/blocking chains, registration and unregistration must always be done in
a process context since the chain is protected by a mutex/rwsem. Also, a
callout routine for a non-raw chain must not try to register or unregister
entries on its own chain. (This did happen in a couple of places and the code
had to be changed to avoid it.)
Since atomic chains may be called from within an NMI handler, they cannot use
spinlocks for synchronization. Instead we use RCU. The overhead falls almost
entirely in the unregister routine, which is okay since unregistration is much
less frequent that calling a chain.
Here is the list of chains that we adjusted and their classifications. None
of them use the raw API, so for the moment it is only a placeholder.
ATOMIC CHAINS
-------------
arch/i386/kernel/traps.c: i386die_chain
arch/ia64/kernel/traps.c: ia64die_chain
arch/powerpc/kernel/traps.c: powerpc_die_chain
arch/sparc64/kernel/traps.c: sparc64die_chain
arch/x86_64/kernel/traps.c: die_chain
drivers/char/ipmi/ipmi_si_intf.c: xaction_notifier_list
kernel/panic.c: panic_notifier_list
kernel/profile.c: task_free_notifier
net/bluetooth/hci_core.c: hci_notifier
net/ipv4/netfilter/ip_conntrack_core.c: ip_conntrack_chain
net/ipv4/netfilter/ip_conntrack_core.c: ip_conntrack_expect_chain
net/ipv6/addrconf.c: inet6addr_chain
net/netfilter/nf_conntrack_core.c: nf_conntrack_chain
net/netfilter/nf_conntrack_core.c: nf_conntrack_expect_chain
net/netlink/af_netlink.c: netlink_chain
BLOCKING CHAINS
---------------
arch/powerpc/platforms/pseries/reconfig.c: pSeries_reconfig_chain
arch/s390/kernel/process.c: idle_chain
arch/x86_64/kernel/process.c idle_notifier
drivers/base/memory.c: memory_chain
drivers/cpufreq/cpufreq.c cpufreq_policy_notifier_list
drivers/cpufreq/cpufreq.c cpufreq_transition_notifier_list
drivers/macintosh/adb.c: adb_client_list
drivers/macintosh/via-pmu.c sleep_notifier_list
drivers/macintosh/via-pmu68k.c sleep_notifier_list
drivers/macintosh/windfarm_core.c wf_client_list
drivers/usb/core/notify.c usb_notifier_list
drivers/video/fbmem.c fb_notifier_list
kernel/cpu.c cpu_chain
kernel/module.c module_notify_list
kernel/profile.c munmap_notifier
kernel/profile.c task_exit_notifier
kernel/sys.c reboot_notifier_list
net/core/dev.c netdev_chain
net/decnet/dn_dev.c: dnaddr_chain
net/ipv4/devinet.c: inetaddr_chain
It's possible that some of these classifications are wrong. If they are,
please let us know or submit a patch to fix them. Note that any chain that
gets called very frequently should be atomic, because the rwsem read-locking
used for blocking chains is very likely to incur cache misses on SMP systems.
(However, if the chain's callout routines may sleep then the chain cannot be
atomic.)
The patch set was written by Alan Stern and Chandra Seetharaman, incorporating
material written by Keith Owens and suggestions from Paul McKenney and Andrew
Morton.
[jes@sgi.com: restructure the notifier chain initialization macros]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Just noticed that request_sock.[ch] contain a useless assignment of
rskq_accept_head to itself. I assume this is a typo and the 2nd one
was supposed to be _tail. However, setting _tail to NULL is not
needed, so the patch below just drops the 2nd assignment.
Signed-off-By: Norbert Kiesel <nkiesel@tbdnetworks.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'audit.b3' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current: (22 commits)
[PATCH] fix audit_init failure path
[PATCH] EXPORT_SYMBOL patch for audit_log, audit_log_start, audit_log_end and audit_format
[PATCH] sem2mutex: audit_netlink_sem
[PATCH] simplify audit_free() locking
[PATCH] Fix audit operators
[PATCH] promiscuous mode
[PATCH] Add tty to syscall audit records
[PATCH] add/remove rule update
[PATCH] audit string fields interface + consumer
[PATCH] SE Linux audit events
[PATCH] Minor cosmetic cleanups to the code moved into auditfilter.c
[PATCH] Fix audit record filtering with !CONFIG_AUDITSYSCALL
[PATCH] Fix IA64 success/failure indication in syscall auditing.
[PATCH] Miscellaneous bug and warning fixes
[PATCH] Capture selinux subject/object context information.
[PATCH] Exclude messages by message type
[PATCH] Collect more inode information during syscall processing.
[PATCH] Pass dentry, not just name, in fsnotify creation hooks.
[PATCH] Define new range of userspace messages.
[PATCH] Filter rule comparators
...
Fixed trivial conflict in security/selinux/hooks.c
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NETFILTER] x_table.c: sem2mutex
[IPV4]: Aggregate route entries with different TOS values
[TCP]: Mark tcp_*mem[] __read_mostly.
[TCP]: Set default max buffers from memory pool size
[SCTP]: Fix up sctp_rcv return value
[NET]: Take RTNL when unregistering notifier
[WIRELESS]: Fix config dependencies.
[NET]: Fill in a 32-bit hole in struct sock on 64-bit platforms.
[NET]: Ensure device name passed to SO_BINDTODEVICE is NULL terminated.
[MODULES]: Don't allow statically declared exports
[BRIDGE]: Unaligned accesses in the ethernet bridge
Implement the half-closed devices notifiation, by adding a new POLLRDHUP
(and its alias EPOLLRDHUP) bit to the existing poll/select sets. Since the
existing POLLHUP handling, that does not report correctly half-closed
devices, was feared to be changed, this implementation leaves the current
POLLHUP reporting unchanged and simply add a new bit that is set in the few
places where it makes sense. The same thing was discussed and conceptually
agreed quite some time ago:
http://lkml.org/lkml/2003/7/12/116
Since this new event bit is added to the existing Linux poll infrastruture,
even the existing poll/select system calls will be able to use it. As far
as the existing POLLHUP handling, the patch leaves it as is. The
pollrdhup-2.6.16.rc5-0.10.diff defines the POLLRDHUP for all the existing
archs and sets the bit in the six relevant files. The other attached diff
is the simple change required to sys/epoll.h to add the EPOLLRDHUP
definition.
There is "a stupid program" to test POLLRDHUP delivery here:
http://www.xmailserver.org/pollrdhup-test.c
It tests poll(2), but since the delivery is same epoll(2) will work equally.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The netdev notifier call chain is currently unregistered without taking
any locks outside the notifier system. Because the notifier system itself
does not synchronise unregistration with respect to the calling of the
chain, we as its user need to do our own locking.
We are supposed to take the RTNL for all calls to netdev notifiers, so
taking the RTNL should be sufficient to protect it.
The registration path in dev.c already takes the RTNL so it's OK.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is version 20 of the Wireless Extensions. This is the
completion of the RtNetlink work I started early 2004, it enables the
full Wireless Extension API over RtNetlink.
Few comments on the patch :
o totally driver transparent, no change in drivers needed.
o iwevent were already RtNetlink based since they were created
(around 2.5.7). This adds all the regular SET and GET requests over
RtNetlink, using the exact same mechanism and data format as iwevents.
o This is a Kconfig option, as currently most people have no
need for it. Surprisingly, patch is actually small and well
encapsulated.
o Tested on SMP, attention as been paid to make it 64 bits clean.
o Code do probably too many checks and could be further
optimised, but better safe than sorry.
o RtNetlink based version of the Wireless Tools available on
my web page for people inclined to try out this stuff.
I would also like to thank Alexey Kuznetsov for his helpful
suggestions to make this patch better.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Steven Whitehouse <steve@chygwyn.com>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
No code changes, just tidying up, in some cases moving EXPORT_SYMBOLs
to just after the function exported, etc.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends {get|set}sockopt compatibility layer in order to
move protocol specific parts to their place and avoid huge universal
net/compat.c file in the future.
Signed-off-by: Dmitry Mishin <dim@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're now starting to have quite a number of places that do skb_pull
followed immediately by an skb_postpull_rcsum. We can merge these two
operations into one function with skb_pull_rcsum. This makes sense
since most pull operations on receive skb's need to update the
checksum.
I've decided to make this out-of-line since it is fairly big and the
fast path where hardware checksums are enabled need to call
csum_partial anyway.
Since this is a brand new function we get to add an extra check on the
len argument. As it is most callers of skb_pull ignore its return
value which essentially means that there is no check on the len
argument.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements an application of the LSM-IPSec networking
controls whereby an application can determine the label of the
security association its TCP or UDP sockets are currently connected to
via getsockopt and the auxiliary data mechanism of recvmsg.
Patch purpose:
This patch enables a security-aware application to retrieve the
security context of an IPSec security association a particular TCP or
UDP socket is using. The application can then use this security
context to determine the security context for processing on behalf of
the peer at the other end of this connection. In the case of UDP, the
security context is for each individual packet. An example
application is the inetd daemon, which could be modified to start
daemons running at security contexts dependent on the remote client.
Patch design approach:
- Design for TCP
The patch enables the SELinux LSM to set the peer security context for
a socket based on the security context of the IPSec security
association. The application may retrieve this context using
getsockopt. When called, the kernel determines if the socket is a
connected (TCP_ESTABLISHED) TCP socket and, if so, uses the dst_entry
cache on the socket to retrieve the security associations. If a
security association has a security context, the context string is
returned, as for UNIX domain sockets.
- Design for UDP
Unlike TCP, UDP is connectionless. This requires a somewhat different
API to retrieve the peer security context. With TCP, the peer
security context stays the same throughout the connection, thus it can
be retrieved at any time between when the connection is established
and when it is torn down. With UDP, each read/write can have
different peer and thus the security context might change every time.
As a result the security context retrieval must be done TOGETHER with
the packet retrieval.
The solution is to build upon the existing Unix domain socket API for
retrieving user credentials. Linux offers the API for obtaining user
credentials via ancillary messages (i.e., out of band/control messages
that are bundled together with a normal message).
Patch implementation details:
- Implementation for TCP
The security context can be retrieved by applications using getsockopt
with the existing SO_PEERSEC flag. As an example (ignoring error
checking):
getsockopt(sockfd, SOL_SOCKET, SO_PEERSEC, optbuf, &optlen);
printf("Socket peer context is: %s\n", optbuf);
The SELinux function, selinux_socket_getpeersec, is extended to check
for labeled security associations for connected (TCP_ESTABLISHED ==
sk->sk_state) TCP sockets only. If so, the socket has a dst_cache of
struct dst_entry values that may refer to security associations. If
these have security associations with security contexts, the security
context is returned.
getsockopt returns a buffer that contains a security context string or
the buffer is unmodified.
- Implementation for UDP
To retrieve the security context, the application first indicates to
the kernel such desire by setting the IP_PASSSEC option via
getsockopt. Then the application retrieves the security context using
the auxiliary data mechanism.
An example server application for UDP should look like this:
toggle = 1;
toggle_len = sizeof(toggle);
setsockopt(sockfd, SOL_IP, IP_PASSSEC, &toggle, &toggle_len);
recvmsg(sockfd, &msg_hdr, 0);
if (msg_hdr.msg_controllen > sizeof(struct cmsghdr)) {
cmsg_hdr = CMSG_FIRSTHDR(&msg_hdr);
if (cmsg_hdr->cmsg_len <= CMSG_LEN(sizeof(scontext)) &&
cmsg_hdr->cmsg_level == SOL_IP &&
cmsg_hdr->cmsg_type == SCM_SECURITY) {
memcpy(&scontext, CMSG_DATA(cmsg_hdr), sizeof(scontext));
}
}
ip_setsockopt is enhanced with a new socket option IP_PASSSEC to allow
a server socket to receive security context of the peer. A new
ancillary message type SCM_SECURITY.
When the packet is received we get the security context from the
sec_path pointer which is contained in the sk_buff, and copy it to the
ancillary message space. An additional LSM hook,
selinux_socket_getpeersec_udp, is defined to retrieve the security
context from the SELinux space. The existing function,
selinux_socket_getpeersec does not suit our purpose, because the
security context is copied directly to user space, rather than to
kernel space.
Testing:
We have tested the patch by setting up TCP and UDP connections between
applications on two machines using the IPSec policies that result in
labeled security associations being built. For TCP, we can then
extract the peer security context using getsockopt on either end. For
UDP, the receiving end can retrieve the security context using the
auxiliary data mechanism of recvmsg.
Signed-off-by: Catherine Zhang <cxzhang@watson.ibm.com>
Acked-by: James Morris <jmorris@namei.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions list_del followed by list_add_tail is equivalent to the
existing inline list_move_tail. list_move_tail avoids unnecessary
_LIST_POISON.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct neigh_ops currently has a destructor field, which no in-kernel
drivers outside of infiniband use. The infiniband/ulp/ipoib in-tree
driver stashes some info in the neighbour structure (the results of
the second-stage lookup from ARP results to real link-level path), and
it uses neigh->ops->destructor to get a callback so it can clean up
this extra info when a neighbour is freed. We've run into problems
with this: since the destructor is in an ops field that is shared
between neighbours that may belong to different net devices, there's
no way to set/clear it safely.
The following patch moves this field to neigh_parms where it can be
safely set, together with its twin neigh_setup. Two additional
patches in the patch series update ipoib to use this new interface.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the thread's lock changes, we're at a new version now.
Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by Arnaldo, this patch replaces the
thread_lock()/thread_unlock() by directly calls to
mutex_lock()/mutex_unlock().
This change makes the code a bit more readable, and the direct calls
are used everywhere in the kernel.
Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
pktgen's thread semaphores are strict mutexes, convert them to the
mutex implementation.
Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch turns the RTNL from a semaphore to a new 2.6.16 mutex and
gets rid of some of the leftover legacy.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With all the previous changes, we're at a new version now.
Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch ports the per-thread interface list list to the in-kernel
linked list implementation. In the general, the resulting code is a
bit simpler.
Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if pktgen's thread initialization fails for all CPUs, the module
will be successfully loaded.
This patch changes that behaivor, by returning an error on module load time,
and also freeing all the resources allocated. It also prints a warning if a
thread initialization has failed.
Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free all the alocated resources if kernel_thread() call fails.
Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
The final result is a simpler and smaller code.
Note that I'm adding a new member in the struct pktgen_thread called
'removed'. The reason is that I didn't find a better wait condition to
be used in the place of the replaced one.
Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lindet run, with some fixes made by hand.
Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Uninline kfree_skb, which saves some 15k of object code on my notebook.
o Allow kfree_skb to be called with a NULL argument.
Subsequent patches can remove conditional from drivers and further
reduce source and object size.
Signed-off-by: Jrn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a race in pktgen which can lead to a double
free of a pktgen_dev's skb. If a worker thread is in
the midst of doing fill_packet(), and the controlling
thread gets a "stop" message, the already freed skb
can be freed once again in pktgen_stop_device(). This
patch gives all responsibility for cleaning up a
pktgen_dev's skb to the associated worker thread.
Signed-off-by: Arthur Kepner <akepner@sgi.com>
Acked-by: Robert Olsson <Robert.Olsson@data.slu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides the core functionality needed for sync events
for ipsec. Derived work of Krisztian KOVACS <hidden@balabit.hu>
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch adds a dormant flag to network devices, RFC2863 operstate derived
from these flags and possibility for userspace interaction. It allows drivers
to signal that a device is unusable for user traffic without disabling
queueing (and therefore the possibility for protocol establishment traffic to
flow) and a userspace supplicant (WPA, 802.1X) to mark a device unusable
without changes to the driver.
It is the result of our long discussion. However I must admit that it
represents what Jamal and I agreed on with compromises towards Krzysztof, but
Thomas and Krzysztof still disagree with some parts. Anyway I think it should
be applied.
Signed-off-by: Stefan Rompf <stefan@loplof.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hi,
When a network interface goes into promiscuous mode, its an important security
issue. The attached patch is intended to capture that action and send an
event to the audit system.
The patch carves out a new block of numbers for kernel detected anomalies.
These are events that may indicate suspicious activity. Other examples of
potential kernel anomalies would be: exceeding disk quota, rlimit violations,
changes to syscall entry table.
Signed-off-by: Steve Grubb <sgrubb@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Originally submitted by Kenzo Iwami; his original description is:
The current bonding driver receives duplicate packets when broadcast/
multicast packets are sent by other devices or packets are flooded by the
switch. In this patch, new flags are added in priv_flags of net_device
structure to let the bonding driver discard duplicate packets in
dev.c:skb_bond().
Modified by Jay Vosburgh to change a define name, update some
comments, rearrange the new skb_bond() for clarity, clear all bonding
priv_flags on slave release, and update the driver version.
Signed-off-by: Kenzo Iwami <k-iwami@cj.jp.nec.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In 295f7324ff I moved defer_accept from
tcp_sock to request_queue and mistakingly reset it at reqsl_queue_alloc, causing
calls to setsockopt(TCP_DEFER_ACCEPT ) to be lost after bind, the fix is to
remove the zeroing of rskq_defer_accept from reqsl_queue_alloc.
Thanks to Alexandra N. Kossovsky <Alexandra.Kossovsky@oktetlabs.ru> for
reporting and testing the suggested fix.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of netfilter-related members are initalized / copied twice in
skb_clone(). Remove one.
Pointed out by Olivier MATZ <olivier.matz@6wind.com>.
And this patch also fixes order of copying / clearing members.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert the following changeset:
bc8dfcb939
Recursive SKB frag lists are really possible and disallowing
them breaks things.
Noticed by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a netlink message is not related to a netlink socket,
it is issued by kernel socket with pid 0. Netlink "pid" has nothing
to do with current->pid. I called it incorrectly, if it was named "port",
the confusion would be avoided.
Signed-off-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu_data blindly allocates bootmem memory to store NR_CPUS instances of
cpudata, instead of allocating memory only for possible cpus.
As a preparation for changing that, we need to convert various 0 -> NR_CPUS
loops to use for_each_cpu().
(The above only applies to users of asm-generic/percpu.h. powerpc has gone it
alone and is presently only allocating memory for present CPUs, so it's
currently corrupting memory).
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Jens Axboe <axboe@suse.de>
Cc: Anton Blanchard <anton@samba.org>
Acked-by: William Irwin <wli@holomorphy.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the following changes:
- add a CONFIG_WIRELESS_EXT select'ed by NET_RADIO for conditional
code
- remove the now no longer required #ifdef CONFIG_NET_RADIO from some
#include's
Based on a patch by Jean Tourrilhes <jt@hpl.hp.com>.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This information is already available via /proc/net/bonding/*
therefore it doesn't make sense to require CAP_NET_ADMIN
privileges.
Original patch by Laurent Deniel <laurent.deniel@free.fr>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the error path if we allocated an fclone then we will free it in
the wrong pool.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes some whitespace issues in net/core/filter.c
Signed-off-by: Kris Katterjohn <kjak@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This replaces a memcmp() with is_zero_ether_addr().
Signed-off-by: Kris Katterjohn <kjak@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This replaces some tests with is_zero_ether_addr(), memcmp(one, two,
6) with compare_ether_addr(one, two), and 6 with ETH_ALEN where
appropriate.
Signed-off-by: Kris Katterjohn <kjak@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes some whitespace issues in net/core/filter.c
Signed-off-by: Kris Katterjohn <kjak@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes redundant comments, and moves one comment to a better
location.
Signed-off-by: Kris Katterjohn <kjak@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: Use <linux/capability.h> where capable() is used.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This removes more unneeded casts on the return value for kmalloc(),
sock_kmalloc(), and vmalloc().
Signed-off-by: Kris Katterjohn <kjak@users.sourceforge.net>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This changes some memcmp(one,two,ETH_ALEN) to compare_ether_addr(one,two).
Signed-off-by: Kris Katterjohn <kjak@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev->get_wireless_stats is deprecated but removing it also removes wireless
subdirectory in sysfs. This patch puts it back.
akpm: I don't know what's happening here. This might be appropriate as a
2.6.15.x compatibility backport. Waiting to hear from Jeff.
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This changes some simple "if (x) BUG();" statements to "BUG_ON(x);"
Signed-off-by: Kris Katterjohn <kjak@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
pktgen_find_thread() and pktgen_create_thread() are only called at
initialization time.
Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
It should return an unsigned value, and fix sk_filter() as well.
Signed-off-by: Kris Katterjohn <kjak@ispwest.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent udev versions don't longer cover bad sysfs timing with built-in
logic. Explicit rules are required to do that. For net devices, the
following is needed:
ACTION=="add", SUBSYSTEM=="net", WAIT_FOR_SYSFS="address"
to handle access to net device properties from an event handler without
races.
This patch changes the main net attributes to be created by the driver
core, which is done _before_ the event is sent out and will not require
the stat() loop of the WAIT_FOR_SYSFS key.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Leave the overloaded "hotplug" word to susbsystems which are handling
real devices. The driver core does not "plug" anything, it just exports
the state to userspace and generates events.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently all network protocols need to call dev_ioctl as the default
fallback in their ioctl implementations. This patch adds a fallback
to dev_ioctl to sock_ioctl if the protocol returned -ENOIOCTLCMD.
This way all the procotol ioctl handlers can be simplified and we don't
need to export dev_ioctl.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Benjamin LaHaise <bcrl@kvack.org>
In __alloc_skb(), the use of skb_shinfo() which casts a u8 * to the
shared info structure results in gcc being forced to do a reload of the
pointer since it has no information on possible aliasing. Fix this by
using a pointer to refer to skb_shared_info.
By initializing skb_shared_info sequentially, the write combining buffers
can reduce the number of memory transactions to a single write. Reorder
the initialization in __alloc_skb() to match the structure definition.
There is also an alignment issue on 64 bit systems with skb_shared_info
by converting nr_frags to a short everything packs up nicely.
Also, pass the slab cache pointer according to the fclone flag instead
of using two almost identical function calls.
This raises bw_unix performance up to a peak of 707KB/s when combined
with the spinlock patch. It should help other networking protocols, too.
Signed-off-by: David S. Miller <davem@davemloft.net>
To help in reducing the number of include dependencies, several files were
touched as they were getting needed headers indirectly for stuff they use.
Thanks also to Alan Menegotto for pointing out that net/dccp/proto.c had
linux/dccp.h include twice.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
static variables should not be explicitly initialised to 0. This causes
them to be placed in .data instead of .bss. This patch de-initialises 3
static variables in net/core/pktgen.c.
There are approximately 800 more such variables in the source tree
(2.6.15rc5). If there is more interrest I'd be willing to track down the
rest of these as well and de-initialise them as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
So that we can share several timewait sockets related functions and
make the timewait mini sockets infrastructure closer to the request
mini sockets one.
Next changesets will take advantage of this, moving more code out of
TCP and DCCP v4 and v6 to common infrastructure.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It also looks like there were 2 places where the test on sk_err was
missing from the event wait logic (in sk_stream_wait_connect and
sk_stream_wait_memory), while the rest of the sock_error() users look
to be doing the right thing. This version of the patch fixes those,
and cleans up a few places that were testing ->sk_err directly.
Signed-off-by: Benjamin LaHaise <benjamin.c.lahaise@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a packet is obtained from skb_recv_datagram with MSG_PEEK enabled
it is left on the socket receive queue. This means that when we detect
a checksum error we have to be careful when trying to free the packet
as someone could have dequeued it in the time being.
Currently this delicate logic is duplicated three times between UDPv4,
UDPv6 and RAWv6. This patch moves them into a one place and simplifies
the code somewhat.
This is based on a suggestion by Eric Dumazet.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch series implements per packet access control via the
extension of the Linux Security Modules (LSM) interface by hooks in
the XFRM and pfkey subsystems that leverage IPSec security
associations to label packets. Extensions to the SELinux LSM are
included that leverage the patch for this purpose.
This patch implements the changes necessary to the XFRM subsystem,
pfkey interface, ipv4/ipv6, and xfrm_user interface to restrict a
socket to use only authorized security associations (or no security
association) to send/receive network packets.
Patch purpose:
The patch is designed to enable access control per packets based on
the strongly authenticated IPSec security association. Such access
controls augment the existing ones based on network interface and IP
address. The former are very coarse-grained, and the latter can be
spoofed. By using IPSec, the system can control access to remote
hosts based on cryptographic keys generated using the IPSec mechanism.
This enables access control on a per-machine basis or per-application
if the remote machine is running the same mechanism and trusted to
enforce the access control policy.
Patch design approach:
The overall approach is that policy (xfrm_policy) entries set by
user-level programs (e.g., setkey for ipsec-tools) are extended with a
security context that is used at policy selection time in the XFRM
subsystem to restrict the sockets that can send/receive packets via
security associations (xfrm_states) that are built from those
policies.
A presentation available at
www.selinux-symposium.org/2005/presentations/session2/2-3-jaeger.pdf
from the SELinux symposium describes the overall approach.
Patch implementation details:
On output, the policy retrieved (via xfrm_policy_lookup or
xfrm_sk_policy_lookup) must be authorized for the security context of
the socket and the same security context is required for resultant
security association (retrieved or negotiated via racoon in
ipsec-tools). This is enforced in xfrm_state_find.
On input, the policy retrieved must also be authorized for the socket
(at __xfrm_policy_check), and the security context of the policy must
also match the security association being used.
The patch has virtually no impact on packets that do not use IPSec.
The existing Netfilter (outgoing) and LSM rcv_skb hooks are used as
before.
Also, if IPSec is used without security contexts, the impact is
minimal. The LSM must allow such policies to be selected for the
combination of socket and remote machine, but subsequent IPSec
processing proceeds as in the original case.
Testing:
The pfkey interface is tested using the ipsec-tools. ipsec-tools have
been modified (a separate ipsec-tools patch is available for version
0.5) that supports assignment of xfrm_policy entries and security
associations with security contexts via setkey and the negotiation
using the security contexts via racoon.
The xfrm_user interface is tested via ad hoc programs that set
security contexts. These programs are also available from me, and
contain programs for setting, getting, and deleting policy for testing
this interface. Testing of sa functions was done by tracing kernel
behavior.
Signed-off-by: Trent Jaeger <tjaeger@cse.psu.edu>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the checks are scattered all over and this leads
to inconsistencies and even cases where the check is not made.
Based upon a patch from Kris Katterjohn.
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem I was seeing turned out to be that skb->dev is NULL when
the checksum is being completed in user context. This happens because
the reference to the device is dropped (to allow it to be released
when packets are in the queue).
Because skb->dev was NULL, the netdev_rx_csum_fault was panicing on
deref of dev->name. How about this?
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a function takes a function pointer as argument it should use the 'return
(*pointer)(params...)' syntax used everywhere else in the kernel as this is
recognized by kernel-doc.
Signed-off-by: Martin Waitz <tali@admingilde.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This way we don't have to check it in sk_run_filter().
Signed-off-by: Kris Katterjohn <kjak@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_valid_name() is a useful function. Make it public.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
in_aton() gives weird results if it sees a newline at the end of the
input. This patch makes it able to handle such input correctly.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Here is the patch that introduces the generic skb_checksum_complete
which also checks for hardware RX checksum faults. If that happens,
it'll call netdev_rx_csum_fault which currently prints out a stack
trace with the device name. In future it can turn off RX checksum.
I've converted every spot under net/ that does RX checksum checks to
use skb_checksum_complete or __skb_checksum_complete with the
exceptions of:
* Those places where checksums are done bit by bit. These will call
netdev_rx_csum_fault directly.
* The following have not been completely checked/converted:
ipmr
ip_vs
netfilter
dccp
This patch is based on patches and suggestions from Stephen Hemminger
and David S. Miller.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most netlink families make no use of the done() callback, making
it optional gets rid of all unnecessary dummy implementations.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
From: Jesper Juhl <jesper.juhl@gmail.com>
This is the net/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in net/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Arnaldo Carvalho de Melo <acme@conectiva.com.br>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
When sk_stream_wait_connect detects a state transition to ESTABLISHED
or CLOSE_WAIT prior to it going to sleep, it will return without
calling finish_wait and decrementing sk_write_pending.
This may result in crashes and other unintended behaviour.
The fix is to always call finish_wait and update sk_write_pending since
it is safe to do so even if the wait entry is no longer on the queue.
This bug was tracked down with the help of Alex Sidorenko and the
fix is also based on his suggestion.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
The recent rewrite of skb_copy_datagram_iovec broke the reception of
zero-size datagrams. This patch fixes it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Attached is kernel patch for UDP Fragmentation Offload (UFO) feature.
1. This patch incorporate the review comments by Jeff Garzik.
2. Renamed USO as UFO (UDP Fragmentation Offload)
3. udp sendfile support with UFO
This patches uses scatter-gather feature of skb to generate large UDP
datagram. Below is a "how-to" on changes required in network device
driver to use the UFO interface.
UDP Fragmentation Offload (UFO) Interface:
-------------------------------------------
UFO is a feature wherein the Linux kernel network stack will offload the
IP fragmentation functionality of large UDP datagram to hardware. This
will reduce the overhead of stack in fragmenting the large UDP datagram to
MTU sized packets
1) Drivers indicate their capability of UFO using
dev->features |= NETIF_F_UFO | NETIF_F_HW_CSUM | NETIF_F_SG
NETIF_F_HW_CSUM is required for UFO over ipv6.
2) UFO packet will be submitted for transmission using driver xmit routine.
UFO packet will have a non-zero value for
"skb_shinfo(skb)->ufo_size"
skb_shinfo(skb)->ufo_size will indicate the length of data part in each IP
fragment going out of the adapter after IP fragmentation by hardware.
skb->data will contain MAC/IP/UDP header and skb_shinfo(skb)->frags[]
contains the data payload. The skb->ip_summed will be set to CHECKSUM_HW
indicating that hardware has to do checksum calculation. Hardware should
compute the UDP checksum of complete datagram and also ip header checksum of
each fragmented IP packet.
For IPV6 the UFO provides the fragment identification-id in
skb_shinfo(skb)->ip6_frag_id. The adapter should use this ID for generating
IPv6 fragments.
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (forwarded)
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Although this message is having the intended effect of causing wireless
driver maintainers to upgrade their code, I never should have merged this
patch in its present form. Leading to tons of bug reports and unhappy
users.
Some wireless apps poll for statistics regularly, which leads to a printk()
every single time they ask for stats. That's a little bit _too_ much of a
reminder that the driver is using an old API.
Change this to printing out the message once, per kernel boot.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add kernel-doc to skbuff.h, skbuff.c to eliminate kernel-doc warnings.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
The code to handle the /proc interface can be cleaned up in several places:
* use seq_file for read
* don't need to remember all the filenames separately
* use for_online_cpu's
* don't vmalloc a buffer for small command from user.
Committer note:
This patch clashed with John Hawkes's "[NET]: Wider use of for_each_*cpu()",
so I fixed it up manually.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Fix some cosmetic issues. Indentation, spelling errors, and some whitespace.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
These are cleanup patches for pktgen that can go in 2.6.15
Can use kzalloc in a couple of places.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
pktgen is calling kmalloc GFP_KERNEL and vmalloc with lock held.
The simplest fix is to turn the lock into a semaphore, since the
thread lock is only used for admin control from user context.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
In 'net' change the explicit use of for-loops and NR_CPUS into the
general for_each_cpu() or for_each_online_cpu() constructs, as
appropriate. This widens the scope of potential future optimizations
of the general constructs, as well as takes advantage of the existing
optimizations of first_cpu() and next_cpu(), which is advantageous
when the true CPU count is much smaller than NR_CPUS.
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
neigh_changeaddr attempts to delete neighbour timers without setting
nud_state. This doesn't work because the timer may have already fired
when we acquire the write lock in neigh_changeaddr. The result is that
the timer may keep firing for quite a while until the entry reaches
NEIGH_FAILED.
It should be setting the nud_state straight away so that if the timer
has already fired it can simply exit once we relinquish the lock.
In fact, this whole function is simply duplicating the logic in
neigh_ifdown which in turn is already doing the right thing when
it comes to deleting timers and setting nud_state.
So all we have to do is take that code out and put it into a common
function and make both neigh_changeaddr and neigh_ifdown call it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
neigh_add_timer cannot use add_timer unconditionally. The reason is that
by the time it has obtained the write lock someone else (e.g., neigh_update)
could have already added a new timer.
So it should only use mod_timer and deal with its return value accordingly.
This bug would have led to rare neighbour cache entry leaks.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Stack traces are very helpful in determining the exact nature of a bug.
So let's print a stack trace when the timer is added twice.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
IPVS used flag NFC_IPVS_PROPERTY in nfcache but as now nfcache was removed the
new flag 'ipvs_property' still needs to be copied. This patch should be
included in 2.6.14.
Further comments from Harald Welte:
Sorry, seems like the bug was introduced by me.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
- added typedef unsigned int __nocast gfp_t;
- replaced __nocast uses for gfp flags with gfp_t - it gives exactly
the same warnings as far as sparse is concerned, doesn't change
generated code (from gcc point of view we replaced unsigned int with
typedef) and documents what's going on far better.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch gets rid of a bogus __in_dev_put() in pktgen.c. This was
spotted by Suzanne Wood.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch renames __in_dev_get() to __in_dev_get_rtnl() and
introduces __in_dev_get_rcu() to cover the second case.
1) RCU with refcnt should use in_dev_get().
2) RCU without refcnt should use __in_dev_get_rcu().
3) All others must hold RTNL and use __in_dev_get_rtnl().
There is one exception in net/ipv4/route.c which is in fact a pre-existing
race condition. I've marked it as such so that we remember to fix it.
This patch is based on suggestions and prior work by Suzanne Wood and
Paul McKenney.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've found the problem in general. It affects any 64-bit
architecture. The problem occurs when you change the system time.
Suppose that when you boot your system clock is forward by a day.
This gets recorded down in skb_tv_base. You then wind the clock back
by a day. From that point onwards the offset will be negative which
essentially overflows the 32-bit variables they're stored in.
In fact, why don't we just store the real time stamp in those 32-bit
variables? After all, we're not going to overflow for quite a while
yet.
When we do overflow, we'll need a better solution of course.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
A bunch of create_proc_dir_entry() calls creating directories had crept
in since the last sweep; converted to proc_mkdir().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I have been experimenting with loadable protocol modules, and ran into
several issues with module reference counting.
The first issue was that __module_get failed at the BUG_ON check at
the top of the routine (checking that my module reference count was
not zero) when I created the first socket. When sk_alloc() is called,
my module reference count was still 0. When I looked at why sctp
didn't have this problem, I discovered that sctp creates a control
socket during module init (when the module ref count is not 0), which
keeps the reference count non-zero. This section has been updated to
address the point Stephen raised about checking the return value of
try_module_get().
The next problem arose when my socket init routine returned an error.
This resulted in my module reference count being decremented below 0.
My socket ops->release routine was also being called. The issue here
is that sock_release() calls the ops->release routine and decrements
the ref count if sock->ops is not NULL. Since the socket probably
didn't get correctly initialized, this should not be done, so we will
set sock->ops to NULL because we will not call try_module_get().
While searching for another bug, I also noticed that sys_accept() has
a possibility of doing a module_put() when it did not do an
__module_get so I re-ordered the call to security_socket_accept().
Signed-off-by: Frank Filz <ffilzlnx@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use iteration instead of recursion. Fraglists within fraglists
should never occur, so we BUG check this.
Signed-off-by: Daniel Phillips <phillips@istop.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we double-add a neighbour entry timer, which should be
impossible but has been reported, dump the current state of
the entry so that we can debug this.
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Amos Waterland <apw@us.ibm.com>
If CONFIG_PROC_FS is not selected, the compiler emits this warning:
net/core/neighbour.c:64: warning: `neigh_stat_seq_fops' defined but not used
Which is correct, because neigh_stat_seq_fops is in fact only
initialized and used by code that is protected by CONFIG_PROC_FS. So
this patch fixes that up.
Signed-off-by: Amos Waterland <apw@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use schedule_timeout_{,un}interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size. Also use
human-time conversion functions instead of hard-coded division to avoid
rounding issues.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts the final 20 DEFINE_SPINLOCK holdouts. (another 580 places
are already using DEFINE_SPINLOCK). Build tested on x86.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up timer initialization by introducing DEFINE_TIMER a'la
DEFINE_SPINLOCK. Build and boot-tested on x86. A similar patch has been
been in the -RT tree for some time.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
