Collects several changes needed after applying
previous mpc5121 platform and driver patches:
- Add mpc5121 reset module node
- Clean up and fix NAND description, remove unused properties
here and correct NAND flash chip size.
- Clean up I2C nodes: remove obsolete "cell-index" properties,
add "fsl,preserve-clocking" property
- Add I2C RTC node for m41t61 RTC
- Add I2C nodes for AD7414 temperature sensor and AT24C32CD3 EEPROM
- Fix compatible property in DMA node
- Clean up CAN nodes, remove unused "cell-index" properties
- Fix compatible property in DIU node
- USB node changes:
- use "fsl,mpc5121-usb2-dr" compatible property only
- remove "port0" and "port1" properties as these are only used
for multi-port host(MHP) module which is not available
on MPC5121.
- use 'fsl,invert-drvvbus' and 'fsl,invert-pwr-fault' in
USB node for internal PHY to specify polarities
of the appropriate port pins.
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Instantiate NAND Flash Controller device if it's
description is found in the device tree.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add reset module registers representation and
machine restart callback for mpc5121 platform.
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Move mpc5121_clk_init() call to platform init code so it won't
get called on non-5121 platforms on a multiplatform kernel.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Commit f71dc176aa 'Make
hpte_need_flush() correctly mask for multiple page sizes' introduced
bug, which is triggered when a kernel with a 64k base page size is run
on a system whose hardware does not 64k hash PTEs. In this case, we
emulate 64k pages with multiple 4k hash PTEs, however in
hpte_need_flush() we incorrectly only mask the hardware page size from
the address, instead of the logical page size. This causes things to
go wrong when we later attempt to iterate through the hardware
subpages of the logical page.
This patch corrects the error. It has been tested on pSeries bare
metal by Michael Neuling.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The code to track the CPPR values added by commit
49bd364713 ("powerpc/pseries: Track previous
CPPR values to correctly EOI interrupts") broke kexec on pseries because
the kexec code in xics.c calls xics_set_cpu_priority() before the IPI has
been EOI'ed. This wasn't a problem previously but it now triggers a BUG_ON
in xics_set_cpu_priority() because os_cppr->index isn't 0.
Fix this problem by setting the index on the CPPR stack to 0 before calling
xics_set_cpu_priority() in xics_teardown_cpu().
Also make it clear that we only want to set the priority when there's just
one CPPR value in the stack, and enforce it by updating the value of
os_cppr->stack[0] rather than os_cppr->stack[os_cppr->index].
While we're at it change the BUG_ON to a WARN_ON.
Reported-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Here are the powerpc bits to remove TIF_ABI_PENDING now that
set_personality() is called at the appropriate place in exec.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
desc->affinity doesn't exit in that case. Let's use a macro for
the UP variant of get_irq_server(), it's the easiest way, avoids
evaluating arguments.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some of the newer 4xx pci cores need an explicit bit set to send
type 1 transactions instead of just comparing the bus numbers.
This patch enables type 1 transations for pcix nodes, thus enabling
devices behind PCI bridges.
Signed-off-by: Stef van Os <stef.van.os@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add missing call to pci_fixup_device(pci_fixup_early, ...) when
building the pci_dev from scratch off the Open Firmware device-tree
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add missing hookup to existing pci_slot when building the pci_dev from
scratch off the Open Firmware device-tree
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We are missing these when building the pci_dev from scratch off
the Open Firmware device-tree
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Embedded PowerPC KVM has an exit timing implementation to track and evaluate
how much time was spent in which exit path.
For Book3S, we don't implement it. So let's not expose it as a config option
either.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Move the defintion and lock helper routines for the cpu hotplug driver
lock from pseries to powerpc code to avoid build breaks for platforms
other than pseries that use cpu hotplug.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It looks like the previous patch sent out to move RTAS and
other items from /proc/ppc64 to /proc/powerpc missed a few
files needed for RAS and DLPAR functionality.
Original Patch here:
http://lists.ozlabs.org/pipermail/linuxppc-dev/2009-September/076096.html
This patch updates the remaining files to be created under /proc/powerpc.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The newly added fixup for buggy dcbX insn's has
a bug that always trigger a kernel TLB walk so a user space
dcbX insn will cause a Kernel Machine Check if it hits DTLB error.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We noticed that recent kernels didn't boot on our 1GHz Canyonlands 460EX
boards anymore. As it seems, patch 8d165db1 [powerpc: Improve
decrementer accuracy] introduced this problem. The routine div_sc()
overflows with shift = 32 resulting in this incorrect setup:
time_init: decrementer frequency = 1000.000012 MHz
time_init: processor frequency = 1000.000012 MHz
clocksource: timebase mult[400000] shift[22] registered
clockevent: decrementer mult[33] shift[32] cpu[0]
This patch now introduces a local div_dc64() version of this function
so that this overflow doesn't happen anymore.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Detlev Zundel <dzu@denx.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
get_viotape_info() declares a vio_waitevent on the stack, which
contains a completion, but never initialises the completion.
I have no idea how this ever worked, and on recent kernels it causes
an oops in handle_tape_event() when we access the non-initialised
completion.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Make sure compiler won't do weird things with limits. E.g. fetching
them twice may return 2 different values after writable limits are
implemented.
I.e. either use rlimit helpers added in
3e10e716ab
or ACCESS_ONCE if not applicable.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pcibus_to_node can return -1 if we cannot determine which node a pci bus
is on. If passed -1, cpumask_of_node will negatively index the lookup array
and pull in random data:
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpus
00000000,00000003,00000000,00000000
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpulist
64-65
Change cpumask_of_node to check for -1 and return cpu_all_mask in this
case:
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpus
ffffffff,ffffffff,ffffffff,ffffffff
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpulist
0-127
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 57b150cce8 (irq: only update affinity if
->set_affinity() is sucessfull) broke xics irq affinity.
We need to use the cpumask passed in, instead of accessing ->affinity directly.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It seems there is a thinko in the TLB invalidation code that makes the
tlbie in the loop executed just once. The intended check was probably
'gt', not 'lt'.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Various kernel asm modifies SRR0/SRR1 just before executing
a rfi. If such code crosses a page boundary you risk a TLB miss
which will clobber SRR0/SRR1. Avoid this by always pinning
kernel instruction TLB space.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit ac4c2a3bbe broke the build
of all powerpc boot wrappers.
It attempts to add an include of autoconf.h but used the wrong
path for it. It also adds -D__KERNEL__ to our boot wrapper, both
things that we pretty much didn't do on purpose so far.
We want our boot wrapper to remain independent enough of the kernel
for various reasons, one of them being that you can "wrap" an existing
kernel at distro install time which allows to ship one kernel image
and a set of boot wrappers for different platforms, the wrappers
don't have to be built out of the same kernel build tree.
It's also incorrect to do what the patch does in our boot environment
since we may not have a proper alignment exception handler which means
we may not be able to fixup the few cases where an unaligned access will
need SW emulation (depends on the core variant, could be when crossing
page or segment boundaries for example).
This patch fixes it by putting the old code back in and using the
new "fancy" variant only when CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
is set, which happens not to be set on powerpc since we don't include
autoconf.h. It also reverts the changes to our boot wrapper Makefile.
This means that x86 should, afaik, keep the optimisations since its
boot wrapper does include autoconf.h and define __KERNEL__ (though I
doubt they make that much different outside of slow embedded processors).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
JFFS2 uses lesser compression ratio and inflate always ends up in "copy
direct from output" case.
This patch tries to optimize the direct copy procedure. Uses
get_unaligned() but only in one place.
The copy loop just above this one can also use this optimization, but I
havn't done so as I have not tested if it is a win there too.
On my MPC8321 this is about 17% faster on my JFFS2 root FS than the
original.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Cc: Roel Kluin <roel.kluin@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mkuboot.sh provides a basic wrapper for the 'mkimage' utility. Using
mkuboot.sh provides clearer error reporting and allows a toolchain to
use its own 'mkimage' executable specified by ${CROSS_COMPILE}mkimage.
Additionally, this brings PowerPC in line with other architectures
which already call mkimage via mkuboot.sh.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI/cardbus: Add a fixup hook and fix powerpc
PCI: change PCI nomenclature in drivers/pci/ (non-comment changes)
PCI: change PCI nomenclature in drivers/pci/ (comment changes)
PCI: fix section mismatch on update_res()
PCI: add Intel 82599 Virtual Function specific reset method
PCI: add Intel USB specific reset method
PCI: support device-specific reset methods
PCI: Handle case when no pci device can provide cache line size hint
PCI/PM: Propagate wake-up enable for PCIe devices too
vgaarbiter: fix a typo in the vgaarbiter Documentation
We were shifting the Ks/Kp/N bits one bit too far on mtsrin. It took
me some time to figure that out, so I also put in some debugging and a
comment explaining the conversion.
This fixes current OpenBIOS boot on PPC64 KVM.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Fix the following build failures:
arch/powerpc/platforms/embedded6xx/flipper-pic.c: In function 'flipper_pic_map':
arch/powerpc/platforms/embedded6xx/flipper-pic.c:105: error: implicit declaration of function 'get_irq_desc'
arch/powerpc/platforms/embedded6xx/hlwd-pic.c: In function 'hlwd_pic_map':
arch/powerpc/platforms/embedded6xx/hlwd-pic.c:98: error: implicit declaration of function 'get_irq_desc'
These failures are caused by the changes introduced in commit
"powerpc: Remove get_irq_desc()". The reason these drivers were not
updated is that they weren't merged yet.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix the following build failures:
arch/powerpc/platforms/embedded6xx/hlwd-pic.c: In function 'hlwd_pic_irq_cascade':
arch/powerpc/platforms/embedded6xx/hlwd-pic.c:135: error: passing argument 1 of 'spin_lock' from incompatible pointer type
arch/powerpc/platforms/embedded6xx/hlwd-pic.c:137: error: passing argument 1 of 'spin_unlock' from incompatible pointer type
arch/powerpc/platforms/embedded6xx/hlwd-pic.c:145: error: passing argument 1 of 'spin_lock' from incompatible pointer type
arch/powerpc/platforms/embedded6xx/hlwd-pic.c:149: error: passing argument 1 of 'spin_unlock' from incompatible pointer type
These failures are caused by the changes introduced in commit
"genirq: Convert irq_desc.lock to raw_spinlock". The reason this driver
was not updated is that it wasn't merged yet.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The retry logic in ug_putc() is broken.
If the TX fifo is not ready and the counter runs out it will have a
value of -1 and no transfer should be attempted. Also, a counter
with a value of 0 means that the TX fifo got ready in the last try
and the transfer should be attempted.
Reported-by: "Juha Leppanen" <juha_motorsportcom@luukku.com>
Signed-off-by: "Juha Leppanen" <juha_motorsportcom@luukku.com>
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since commit 57b150cce8, desc->affinity
of an irq is changed after calling desc->chip->set_affinity.
Therefore we need to fix the irq_choose_cpu() not to depend on the
desc->affinity for new mask.
Signed-off-by: Jiajun Wu <b06378@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit d28513bc7f ("Fix bug in pagetable
cache cleanup with CONFIG_PPC_SUBPAGE_PROT"), itself a fix for
breakage caused by an earlier clean up patch of mine, contains a
stupid bug. I changed the parameters of the subpage_protection()
function, but failed to update one of the callers.
This patch fixes it, and replaces a void * with a typed pointer so
that the compiler will warn on such an error in future.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The _ONSTACK variant should be used for on-stack completion,
otherwise it will break lockdep.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On machines using the Apple U4 bridge (AKA IBM CPC945) PCIe interface such
as the latest generation G5 machines x16 slot or the x16 slot of the
PowerStation, MSIs are currently broken (and will oops when enabling).
This fixes the oops and implements proper support for those. Instead of
using the PCIe <-> HT bridge conversion, on such slots we need to use
a bunch of magic registers in the bridge as the MSI target, encoding
the interrupt number in the low bits of the address itself
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch fixes the handling of VSX alignment faults in little-endian
mode (the current code assumes the processor is in big-endian mode).
The patch also makes the handlers clear the top 8 bytes of the register
when handling an 8 byte VSX load.
This is based on 2.6.32.
Signed-off-by: Neil Campbell <neilc@linux.vnet.ibm.com>
Cc: <stable@kernel.org>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The function name of cpumask_clear_cpu was not correct. Fortunately
nobody uses that code with hotplug yet :-)
Reported-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This time without the funny characters.
Fix following build errors generated with DEBUG=1
cc1: warnings being treated as errors
arch/powerpc/mm/hash_utils_64.c: In function 'htab_dt_scan_page_sizes':
arch/powerpc/mm/hash_utils_64.c:343: error: format '%04x' expects type 'unsigned int', but argument 4 has type 'long unsigned int'
arch/powerpc/mm/hash_utils_64.c:343: error: format '%08x' expects type 'unsigned int', but argument 5 has type 'long unsigned int'
arch/powerpc/mm/hash_utils_64.c: In function 'htab_initialize':
arch/powerpc/mm/hash_utils_64.c:666: error: format '%x' expects type 'unsigned int', but argument 4 has type 'long unsigned int'
... SNIP ...
Signed-off-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use the new unreachable() macro instead of for(;;);
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Paul Mackerras <paulus@samba.org>
CC: linuxppc-dev@ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
