Replace the chip lock by a the controller lock. For simple drivers a
dummy controller structure is created by the scan code.
This simplifies the locking algorithm in nand_get/release_chip().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Unrolling the loops produces denser and much faster code.
Add a config switch which allows to select the byte order of the
resulting ecc code. The current Linux implementation has a byte
swap versus the SmartMedia specification
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The previous code wouldn't work correctly on architectures which have a
non-empty MODULE_SYMBOL_PREFIX, and this version is neater if slightly
less optimal in the built-in case.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The patch below adds support for the NAND device on the Amstrad Delta.
This is a 32MiB 8bit Toshiba device, with the data bus connected to the
OMAP MPUIO pins and ALE, CLE, NCE, NRE, NWE and NWP all connected to the
Delta's latch2 16bit latch.
Signed-Off-By: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
drivers/mtd/devices/docprobe.c: In function `DoC_Probe':
drivers/mtd/devices/docprobe.c:338: warning: assignment from incompatible pointer type
drivers/mtd/devices/docprobe.c:341: warning: assignment from incompatible pointer type
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
There is a second revision of "mtdconcat NAND/Sibley" patch. I hope
the patch will not get damaged as I'm posting it from gmail account,
thanks to Jorn.
The patch adds previously missing concat_writev(),
concat_writev_ecc(), concat_block_isbad(), concat_block_markbad()
functions to make concatenation layer compatible with Sibley and NAND
chips.
Patch has been cleared from whitespaces, fixed some lines of code as
requested. Also I have added code for alignment check that should
support Jorn's "writesize" patch.
Signed-off-by: Alexander Belyakov <alexander.belyakov@intel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The following difference was found between the mainline and linux-mips
kernel. LASAT depends on MTD_CFI.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
In an unrelated MTD commit, a description about the ms02-nv module
got removed from Kconfig. While I personally agree with this
removal, the module maintainer (Maciej W. Rozycki) would like to
see it added back. In the absense of any consistency regarding
Kconfig descriptions his wish should be followed.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
'oobavail' parameter of mtd_info structure is now propagated to the MTD
partitions
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This allows for much better abstraction and separation of the XIP and
non-XIP cases with their own specific implementations. This fixes the
case where a timeout was tripped on in the XIP case by the code that
was meant for the non-XIP case only.
This also makes for a nice code reduction.
Signed-off-by: Nicolas Pitre <nico@cam.org>
CC: "Alexey, Korolev" <alexey.korolev@intel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The patch below fixes a potential starvation issue that can arise when
there is contention on a chip during a period when a process is
currently writing to it. The starvation is avoided by conditionally
rescheduling when the chip is left in a state usable by other processes.
Signed-off-by: Josh Boyer <jdub@us.ibm.com>
Signed-off-by: Tom Gall <tom_gall@vnet.ibm.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
On AMD Au1550 the static bus controller fails to keep -CE asserted during
chip ready delay on read commands and the NAND chip being used requires this.
So, the current driver allows nand_base.c to drive -CE manually during the
entire sector read. When the PCMCIA driver is enabled however, occasionally
the ECC errors occur on NAND reads. This happens because the PCMCIA driver
polls sockets periodically and reads one of the board's control/status regs
(BCSRs) which are on the same static bus as the NAND flash, and just use
another chip select (and the NOR flash also resides on that bus), so as the
NAND driver forces NAND chip select asserted and the -RE signal is shared, a
contention occurs on the static bus when BCSR or NOR flash is read while we're
reading from NAND.
So, we either can't keep interrupts enabled during the whole NAND sector
read (which is hardly acceptable), or have to implement some interlocking
scheme between multiple drivers (which is painful, and makes me shudder :-).
There's a third way which has proven to work: to force -CE asserted only
while we're waiting for a NAND chip to become ready after a read command,
disabling interrupts for a maximum of 25 microseconds (according to Toshiba
TC58DVM92A1FT00 datasheet -- this chip is mentioned in the board schematics);
for Samsung NAND chip which seems to be actually used this delay is even less,
12 us.
Signed-off-by: Konstantin Baydarov <kbaidarov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix build warnings from drivers/mtd/redboot.c due to
use of `unsigned long` in `struct fis_image_desc` for
fields being passed to swab32s() which expects __u32 *
Change the entries to uint32_t to make them compatible
with the swab32s() function
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
During the last cleanup of the AMD Au1550 NAND driver the old buglet was
reintroduced: as the MEM_STNDCTL register is write-only and seem to always
read as 0x31, read-modify-write to it done in au1xxx_nand_init() will have the
side effect of enabling -RCS0/1 pin override (via bits 4/5 of this reg.), thus
possibly causing a contention on the static bus when the NOR flash (using
-RCS0) or board control status registers (using -RCS2) are read. Luckily, this
goes away with a first NAND access, since au1550_hwcontrol() doesn't try to
read this register before writing anymore.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
We all inherited the same error from the original NAND board driver which
got copied and changed. Fix them all at once...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
On Mon, May 15, 2006 at 12:56:37AM -0700, Andrew Morton wrote:
>...
> Changes since 2.6.17-rc3-mm1:
>...
> git-mtd.patch
>...
> git trees
>...
If we correct the names of the config options, the code might actually
work as intended...
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
On alpha:
drivers/net/dl2k.c: In function `rio_free_tx':
drivers/net/dl2k.c:768: error: `DMA_48BIT_MASK' undeclared (first use in this function)
drivers/net/dl2k.c:768: error: (Each undeclared identifier is reported only once
drivers/net/dl2k.c:768: error: for each function it appears in.)
drivers/net/dl2k.c: In function `receive_packet':
drivers/net/dl2k.c:896: error: `DMA_48BIT_MASK' undeclared (first use in this function)
drivers/net/dl2k.c: In function `rio_close':
drivers/net/dl2k.c:1803: error: `DMA_48BIT_MASK' undeclared (first use in this function)
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the IBM microdrive to the known PCMCIA IDs for ide_cs.
Signed-off-by: Thomas Kleffel <tk@maintech.de>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do not enable the SMBus device on Asus boards if suspend is used. We do
not reenable the device on resume, leading to all sorts of undesirable
effects, the worst being a total fan failure after resume on Samsung P35
laptop.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/char/tpm/tpm.c: In function 'tpm_register_hardware':
drivers/char/tpm/tpm.c:1157: warning: assignment from incompatible pointer type
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Acked-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the constant used for the base address when it cannot be determined
from ACPI. It was off by one order of magnitude.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the error handling of some LED _store functions. This corrects them to
return -EINVAL if the value is not numeric with an optional byte of trailing
whitespace.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The backlight and LCD class _store functions currently accept values like "34
some random strings" without error. This corrects them to return -EINVAL if
the value is not numeric with an optional byte of trailing whitespace.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Improve the NEW_LEDS Kconfig information to say what it does as well as what
it doesn't.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While debugging why our LCS emulator is having some problems I noticed the
following weirdness in drivers/s390/net/lcs.c routine lcs_irq. The `if'
statement is always true since SCHN_STAT_PCI is defined as 0x80.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
An earlier commit (75cf7456dd) changed an
overly-zealous PCI quirk to only poke those VIA devices that need it.
However, some PCI devices were not included in what I hope is now the full
list. Consequently we're failing to run the quirk on all machines which need
it, causing IRQ routing failures.
This should I hope correct this.
Thanks to Masoud Sharbiani <masouds@masoud.ir> for pointing this out
and testing the fix.
Signed-off-by: Chris Wedgwood <cw@f00f.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix some NULL dereferences in the pcmcia code when using old userland
tools.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The TIS driver is dependent upon information from the ACPI table for device
discovery thus it compiles but does no actual work without this dependency.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I am having the bug FATAL: Error inserting capi ([..]/capi.ko): Device or
resource busy when I try to reload capi after loading it. in dmesg:
capi20: unable to get major 68
Fix the issue which is caused by setting the major to zero when registering
the chrdev succeeded.
(akpm: this means that we can again not use `major=0' (dynamic major
allocation) for this driver).
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make it work even with compilers which lack the wit to notice that
THIS_MODULE is always non-NULL. Use #ifdef MODULE instead. It's only
a temporary debugging check anyway.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The physmap platform driver conversion added to physmap.c an include
of asm/mach/flash.h which is 1) ARM-specific; and 2) isn't actually
necessary. Remove it.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
We used to calculate the number of chips to be zero, allocate an array
of that size, then nasty things would happen when we attempt to access
the first object in that zero-sized array.
Now, if the number of _full_ chips that would fit into the map is zero,
we allocate an array of one anyway, and then artificially reduce the
total size of the resulting MTD device to fit in the map.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
There's a mem leak in drivers/mtd/devices/block2mtd.c::block2mtd_setup()
We can leak 'name' allocated with kmalloc in 'parse_name' if leave via
the 'parse_err' macro since it contains a return but doesn't do any
freeing.
Spotted by coverity checker as bug 615.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The _board_ driver needs to be mtd->owner, and it in turn pins the
nand.ko module. Fix them all to actually do that, and fix nand.ko not to
overwrite it -- and also to check that the caller sets it, if the caller
is a module.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
There are two code paths in drivers/mtd/devices/phram.c::phram_setup() that
will leak memory.
Memory is allocated to the variable 'name' with kmalloc() by the
parse_name() function, but if we leave by way of the parse_err() macro,
then that memory is never kfree()'d, nor is it ever used with
register_device() so it won't be freed later either - leak.
Found by the Coverity checker as #593 - simple fix below.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
