Current code calculates scaling factors for video overlays even when the
overlays are not scaled. Change the code to skip calculations when not
scaling.
This optimizes the code a bit, but also fixes a problem when configuring
an overlay for a disabled display: if the display is disabled we don't
necessarily know the pixel clock used when the display is enabled, and
in some cases (like HDMI) the pixel clock is set to zero until a proper
video mode is set later. A wrong pixel clock will mess up the
scaling calculations, causing an error like:
omapdss DISPC error: failed to set up scaling, required fclk rate = 0
Hz, current fclk rate = 170666666 Hz
A proper fix would be to check later whether the clocks are enough for the
scaling, at the point when the overlay or display is actually enabled,
but this patch removes the problem for now.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
hdmi_get_pixel_clock() returns the pixel clock in Hz, but the pck is
stored as kHz. This means the return value has to be multiplied by 1000,
not by 10000 as the code did.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
They were getting this implicitly by an include of module.h
from device.h -- but we are going to clean that up and break
that include chain, so include module.h explicitly now.
[ with contributions from Axel Lin <axel.lin@gmail.com> ]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
With module.h being implicitly everywhere via device.h, the absence
of explicitly including something for EXPORT_SYMBOL went unnoticed.
Since we are heading to fix things up and clean module.h from the
device.h file, we need to explicitly include these files now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Add zorder support on OMAP4, this feature allows deciding the visibility order
of the overlays based on the zorder value provided as an overlay info parameter
or a sysfs attribute of the overlay object.
Use the overlay cap OMAP_DSS_OVL_CAP_ZORDER to determine whether zorder is
supported for the overlay or not. Use dss feature FEAT_ALPHA_FREE_ZORDER
if the caps are not available.
Ensure that all overlays that are enabled and connected to the same manager
have different zorders. Swapping zorders of 2 enabled overlays currently
requires disabling one of the overlays.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add support for VIDEO3 pipeline on OMAP4:
- Add VIDEO3 pipeline information in dss_features and omapdss.h
- Add VIDEO3 pipeline register coefficients in dispc.h
- Create a new overlay structure corresponding to VIDEO3.
- Make changes in dispc.c for VIDEO3
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
On OMAP3, in order to enable alpha blending for LCD and TV managers, we needed
to set LCDALPHABLENDERENABLE/TVALPHABLENDERENABLE bits in DISPC_CONFIG. On
OMAP4, alpha blending is always enabled by default, if the above bits are set,
we switch to an OMAP3 compatibility mode where the zorder values in the pipeline
attribute registers are ignored and a fixed priority is configured.
Rename the manager_info member "alpha_enabled" to "partial_alpha_enabled" for
more clarity. Introduce two dss_features FEAT_ALPHA_FIXED_ZORDER and
FEAT_ALPHA_FREE_ZORDER which represent OMAP3-alpha compatibility mode and OMAP4
alpha mode respectively. Introduce an overlay cap for ZORDER. The DSS2 user is
expected to check for the ZORDER cap, if an overlay doesn't have this cap, the
user is expected to set the parameter partial_alpha_enabled. If the overlay has
ZORDER cap, the DSS2 user can assume that alpha blending is already enabled.
Don't support OMAP3 compatibility mode for now. Trying to read/write to
alpha_blending_enabled sysfs attribute issues a warning for OMAP4 and does not
set the LCDALPHABLENDERENABLE/TVALPHABLENDERENABLE bits.
Change alpha_enabled to partial_alpha_enabled in the omap_vout driver. Use
overlay cap "OMAP_DSS_OVL_CAP_GLOBAL_ALPHA" to check if overlay supports alpha
blending or not. Replace this with checks for VIDEO1 pipeline.
Cc: linux-media@vger.kernel.org
Cc: Lajos Molnar <molnar@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add support to dump the HDMI wrapper, core, PLL and PHY registers
through debugfs.
Signed-off-by: Mythri P K <mythripk@ti.com>
[tomi.valkeinen@ti.com: updated the description]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add some of the missing register definitions, which are h/w indexable.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove usage of hdmi_reg struct to use u16 instead in the HDMI IP header
file. hdmi_reg struct is not really needed, and the same change was also
made for dispc earlier.
Signed-off-by: Mythri P K <mythripk@ti.com>
[tomi.valkeinen@ti.com: updated the description]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move the comments in AVI infoframe structure above each parameter
to align with other comments in the header file.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Create a dss_range_param member called FEAT_PARAM_DOWNSCALE to get the maximum
downscaling possible on the current platform. Use this in
dispc_ovl_calc_scaling().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move DISPC scaling related code from dispc_ovl_setup() to a new function
dispc_ovl_calc_scaling(). Use overlay caps to check if the overlay can scale or
not. No functional changes are made.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The function calc_fclk_five_taps() uses a fixed value of pixels per line which
is used in calculations to get the minimum fclk needed for scaling with five
taps to work.
Remove this by providing the width of the panel connected to the manager.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dispc_mgr_pclk_rate() is used to calculate minimum required functional clock for
scaling in calc_fclk() and calc_fclk_five_taps(). This function returns the
correct pixel clock for LCD and LCD2 managers, but not for TV manager. Extend
this function so that it gets the correct pixel clock for TV manager.
This also prevents the crash we get when we try to scale overlays connected to
TV manager. The current code leads to a BUG() being executed if we call
dispc_mgr_pclk_rate() for the TV manager.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Create a helper function called dispc_mgr_is_lcd() which returns true if the
manager is LCD or LCD2.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dispc_ovl_enable_replication() and dispc_ovl_set_fifo_threshold() are currently
called in configure_overlay(). These are the only functions which cause DISPC
register writes of overlay parameters outside of dispc_ovl_setup().
Move these to dispc_ovl_setup() and pass replication, fifo_low and fifo_high
thresholds as arguments to dispc_ovl_setup() in order to be aligned with other
overlay parameters. No functional changes are made.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dispc_ovl_setup() currently takes a large number of overlay arguments, most of
these are members of the overlay_info struct. Replace these arguments by
passing a overlay_info pointer instead.
In configure_overlay(), we create an overlay_info struct called new_oi, this is
a copy of the overlay cache's overlay_info member. Update the new_oi parameters
which could have been possibly changed in configure_overlay(). Pass its pointer
pointer to dispc_ovl_setup().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Implement detect() by checking the hot plug detect status.
The implementation is not very good, as it always turns on the HDMI
output to get the detection working. HDMI driver needs improvements so
that we could enable only core parts of it.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
check_timings() is supposed to be used to verify if timings are ok or
not. Currently the HDMI driver prints error messages if the timings are
not ok. This is not right, as it is no error to give invalid timings to
check_timings().
Remove the error prints.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Clean up reading of EDID by passing direct address to the block being
read, instead of start address of the whole EDID memory area. Rewrite
the loop which reads the EDID.
This also fixes the checksum calculation, which used to calculate the
checksum only for the first block.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Split the DDC initialization off from hdmi_core_ddc_edid() into a
separate function hdmi_core_ddc_init(). This cleans up the
implementation.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAPFB handles EDID parsing now, using the common helper functions in
fbdev. We can remove the EDID parsing from HDMI driver.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Implement read_edid() for HDMI by implementing necessary functions to
hdmi.c and to hdmi_omap4_panel.c.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently the set_timings code for hdmi is quite strange. The display is
disabled in hdmi_omap4_panel.c before setting timings, and enabled in
hdmi.c after setting the timings. Furthermore, the timings were not
permanent, and disabling and enabling the display would lose them.
This patch makes the set_timings handling a bit better.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Enabling HDMI output often causes sync lost errors, and almost always
causes timeout errors being printed from dispc_mgr_enable_digit_out().
The sync lost problem seems to go lessen greatly if we first enable the
HDMI output, and only then enable the DISPC output. However, as this is
only based on observations, the fix may not be perfect as the problem
may lie somewhere else. Nevertheless, HDMI works better with this patch.
This will also fix the dispc's dispc_mgr_enable_digit_out(), as the code
waits for two VSYNCs after enabling the output. If the HDMI output is
disabled (as it was previously), there are no VSYNCs and
dispc_mgr_enable_digit_out() will print timeout errors.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dispc_mgr_enable_digit_out() didn't handle HDMI case very well.
Improve the function to use FRAMEDONETV interrupt to see when HDMI has
been disabled.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add dss_get_hdmi_venc_clk_source(), which can be used to get the value
programmed with dss_select_hdmi_venc_clk_source(). This can be used to
find out if the digit output is going to VENC or HDMI.
For OMAP2/3 dss_get_hdmi_venc_clk_source() always returns
DSS_VENC_TV_CLK.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
regn divider is currently programmed to the registers without change,
but when calculating clock frequencies it is used as regn+1.
To make this similar to how DSI handles the dividers this patch changes
the regn value to be used as such for calculations, but the value
programmed to registers is regn-1.
This simplifies the clock frequency calculations, makes it similar to
DSI, and also allows us to use regn value 0 as undefined.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use default regn and regm2 dividers in the hdmi driver if the board file
does not define them.
Cc: Mythri P K <mythripk@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The current driver had a hardcoded minimum value of 2 for pixel clock
divisor (PCD). This doesn't seem to be right.
OMAP4 TRM says that PCD can be 1 when not downscaling, and inverted
pixel clock (IPC) is off.
OMAP3 TRM says the same, but also in the register descriptions that PCD
value 1 is invalid.
OMAP2 TRM says PCD 2 is the minimum.
OMAP2 is still untested, but for both OMAP3 and OMAP4 PCD of 1 seems to
work fine.
This patch adds a new DSS feature, FEAT_PARAM_DSS_PCD, which is used to
find the minimum and maximum PCD. The minimum is set to 2 for OMAP2, and
1 for OMAP3/4.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
As the panel driver will remain generic across OMAP's renaming it to
hdmi_panel.c
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
HDMI IP fundamentally has replaceable core PHY and PLL blocks.
These blocks might vary across OMAP's but the end functionality such as to
enable or disable PLL, PHY, function to read EDID would remain the same.
Thus to make the current hdmi DSS driver compatible with different OMAP's having
different IP blocks( A combination of different core, PHY, PLL blocks), function
pointer approach is introduced.
With function pointer, relevant IP dependent functions are mapped to the generic
functions used by DSS during the initialization based on the OMAP compiled.
Thus making hdmi DSS driver IP agnostic.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Functions that are included in HDMI IP driver is renamed to have
IP specific names so that it will not conflict with similar functions
from other IP.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move HDMI IP dependent audio functions from HDMI DSS file to IP library.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Split the current HDMI driver to move the HDMI IP dependent ( PLL/PHY/Core
configuration code) to a new IP file (ti_hdmi_4xxx_ip.c.
This is to separate IP dependent OMAP agnostic code from OMAP specific DSS
dependent code.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Clean up to move the EDID definition from the IP dependent header file to hdmi.c
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Some of the header file definitions that are there in the hdmi.h are generic
and can be used across OMAP's, Thus moving generic definition to new file.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
As hdmi has few additional parameters such as vsync and hsync
polarity which is missing in DSS timing structure, define HDMI timings
structure for hdmi to use instead of OMAP DSS timing structure.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
As the pll and the video configuration info are part of the ip_data, pll
and video structures are moved to the ip_data structure. Also the pll and
video configuration functions are modified accordingly to take care of the
structure movement.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
As the base_address of the HDMI might differ across SoC's, offset of the HDMI
logical blocks(PHY, PLL and Core) and base address procured from the platform
data are passed dynamically to the functions that modify HDMI IP registers.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add initial support for DSI video mode panels:
- Add a new structure omap_dss_dsi_videomode_data in the member "panel" in
omap_dss_device struct. This allows panel driver to configure dsi video_mode
specific parameters.
- Configure basic DSI video mode timing parameters: HBP, HFP, HSA, VBP, VFP, VSA,
TL and VACT.
- Configure DSI protocol engine registers for video_mode support.
- Introduce functions dsi_video_mode_enable() and dsi_video_mode_disable() which
enable/disable video mode for a given virtual channel and a given pixel format
type.
Things left for later
- Add functions to check for errors in video mode timings provided by panel.
- Configure timing registers required for command mode interleaving.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dsi_vc_send_null() currently sends a long packet with data type
MIPI_DSI_NULL_PACKET and packet length 4. Modify it to send a zero
length long packet. This leads to sending only the long packet header
and no payload packets and hence the transfer completes faster.
The function can be modified later if there is a need to send null
packets of a non-zero length.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently, DSI pixel info is only represented by the pixel size in bits using
the pixel_size parameter in omap_dss_device struct's ctrl member.
This is not sufficient information for DSI video mode usage, as two of the
supported formats(RGB666 loosely packed, and RGB888) have the same pixel
container size, but different data_type values for the video mode packet header.
Create enum "omap_dss_dsi_pixel_format" which describes the pixel data format
the panel is configured for. Create helper function dsi_get_pixel_size() which
returns the pixel size of the given pixel format.
Modify functions omapdss_default_get_recommended_bpp() and dss_use_replication()
to use dsi_get_pixel_size().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Split the function dispc_set_parallel_interface_mode() into 2 separate
functions called dispc_mgr_set_io_pad_mode() and dispc_mgr_enable_stallmode().
The current function tries to set 2 different modes(io pad mode and stall mode)
based on a parameter omap_parallel_interface_mode which loosely corresponds to
the panel interface type.
This isn't correct because a) these 2 modes are independent to some extent,
b) we are currently configuring gpout0/gpout1 for DSI panels which is
unnecessary, c) a DSI Video mode panel won't get configured correctly.
Splitting the functions allows the interface driver to set these modes
independently and hence allow more flexibility.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Introduce read functions which use generic Processor-to-Peripheral
transaction types. These are needed by some devices which may not support
corresponding DCS commands.
Add function dsi_vc_generic_send_read_request() which can send
a short packet with 0, 1 or 2 bytes of request data and the corresponding
generic data type.
Rename function dsi_vc_dcs_read_rx_fifo() to dsi_vc_read_rx_fifo() and modify
it to take the enum "dss_dsi_content_type" as an argument to use either DCS
or GENERIC Peripheral-to-Processor transaction types while parsing data read
from the device.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Split dsi_vc_dcs_read() into the functions:
- dsi_vc_dcs_send_read_request(): This is responsible for sending the short
packet command with the read request.
- dsi_vc_dcs_read_rx_fifo(): This parses the DSI RX fifo of the given virtual
channel, identifies the type of data received, and fills a buffer with the data
provided by the panel.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove functions dsi_vc_dcs_read_1() and dsi_vc_dcs_read_2(), these are used
when the panel is expected to return 1 and 2 bytes respecitvely. This was manily
used for debugging purposes. These functions should be implemented in the panel
driver if needed.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Intoduce enum "dss_dsi_content_type" to differentiate between DCS and generic
content types.
Introduce short and long packet write functions which use generic
Processor-to-Peripheral transaction types. These are needed by some devices
which may not support corresponding DCS commands. Create common write functions
which allow code reuse between DCS and generic write functions.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Create an enum for DSI operation modes, use this to set the capabilities of the
device in dsi_init_display().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
