Preventing HIGHPTE allocations under VMI will allow us to remove the
kmap_atomic_pte paravirt op.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
LKML-Reference: <1267204562-11844-2-git-send-email-ian.campbell@citrix.com>
Acked-by: Alok Kataria <akataria@vmware.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
There's a path in the pagefault code where the kernel deliberately
breaks its own locking rules by kmapping a high pte page without
holding the pagetable lock (in at least page_check_address). This
breaks Xen's ability to track the pinned/unpinned state of the
page. There does not appear to be a viable workaround for this
behaviour so simply disable HIGHPTE for all Xen guests.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
LKML-Reference: <1267204562-11844-1-git-send-email-ian.campbell@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Pasi Kärkkäinen <pasik@iki.fi>
Cc: <stable@kernel.org> # .32.x: 14315592: Allow highmem user page tables to be disabled at boot time
Cc: <stable@kernel.org> # .32.x
Cc: <xen-devel@lists.xensource.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (88 commits)
powerpc: Fix lwsync feature fixup vs. modules on 64-bit
powerpc: Convert pmc_owner_lock to raw_spinlock
powerpc: Convert die.lock to raw_spinlock
powerpc: Convert tlbivax_lock to raw_spinlock
powerpc: Convert mpic locks to raw_spinlock
powerpc: Convert pmac_pic_lock to raw_spinlock
powerpc: Convert big_irq_lock to raw_spinlock
powerpc: Convert feature_lock to raw_spinlock
powerpc: Convert i8259_lock to raw_spinlock
powerpc: Convert beat_htab_lock to raw_spinlock
powerpc: Convert confirm_error_lock to raw_spinlock
powerpc: Convert ipic_lock to raw_spinlock
powerpc: Convert native_tlbie_lock to raw_spinlock
powerpc: Convert beatic_irq_mask_lock to raw_spinlock
powerpc: Convert nv_lock to raw_spinlock
powerpc: Convert context_lock to raw_spinlock
powerpc/85xx: Add NOR, LEDs and PIB support for MPC8568E-MDS boards
powerpc/86xx: Enable VME driver on the GE SBC610
powerpc/86xx: Enable VME driver on the GE PPC9A
powerpc/86xx: Add MSI section to GE PPC9A DTS
...
The following patch defines sigcontext ABI of ColdFire. Due to ISA
restrictions ColdFire needs different rt_sigreturn trampoline.
And due to ColdFire FP registers being 8-bytes instead of 12-bytes on
m68k, sigcontext and fpregset structures should be updated.
Regarding the sc_fpstate[16+6*8] field, it would've been enough 16
bytes to store ColdFire's FP state. To accomodate GLIBC's libSegFault
it would'be been enough 6*8 bytes (room for the 6 non-call-clobbered
FP registers). I set it to 16+6*8 to provide some extra space for any
future changes in the ColdFire FPU.
Signed-off-by: Maxim Kuvyrkov <maxim@codesourcery.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Port syscalls for NPTL support to m68knommu.
Signed-off-by: Maxim Kuvyrkov <maxim@codesourcery.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
This patch adds several syscalls, that provide necessary
functionality to support NPTL on m68k/ColdFire.
The syscalls are get_thread_area, set_thread_area, atomic_cmpxchg_32 and
atomic_barrier.
The cmpxchg syscall is required for ColdFire as it doesn't support 'cas'
instruction.
Also a ptrace call PTRACE_GET_THREAD_AREA is added to allow debugger to
inspect the TLS storage.
Signed-off-by: Maxim Kuvyrkov <maxim@codesourcery.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
This patch switches m68k to generic siginfo layout. The custom layout
of m68k's `struct siginfo' had several issues due to not considering
aliasing of members in the union, e.g., _uid32 was at different offsets
in ._kill, ._rt and ._sigchld.
Signed-off-by: Maxim Kuvyrkov <maxim@codesourcery.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The valkyriefb driver needs the CUDA to work in order to set the video
mode at boot. So initialise the device earlier, and bring the m68k code
closer to the powermac code.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Move platform device code from the drivers to the platform init function.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Move platform device code from the driver to the platform init function.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Remove the old 68k Mac serial port code and a lot of related cruft. Add
new SCC platform devices to mac 68k platform.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Add platform driver support to the pmac-zilog driver, for m68k macs.
Place the powermac-specific code inside #ifdef CONFIG_PPC_PMAC.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Adjust the platform device code to conform with the code style used in the
rest of this patch series. No need to name resources nor to register
devices which are not applicable.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cleanup whitespace and comments. Remove some dead code.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
@depends on haskernel@
expression x,__divisor;
@@
- (((x) + ((__divisor) / 2)) / (__divisor))
+ DIV_ROUND_CLOSEST(x,__divisor)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Remove the comments referring to a function map_chunk that no longer exists.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The test in __ioremap to reject memory ranges crossing the 0 boundary
rejects also memory ranges ending at the end of the memory. Fix that.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Updated, leaner defconfig for the alchemy development boards.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1005/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Don't define platform info for second mac on au1100 (which only has a
single mac).
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1004/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A few hunks somehow ended up outside their #ifdef/endif blocks,
leading to -Werror-induces build failures.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1003/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The GT-64111 PCI host bridge has no address translation mechanism, so
it can't generate legacy port accesses. This quirk fixes legacy device
port resources to contain the bus addresses actually generated by the
GT-64111.
I think this is the approach Ben Herrenschmidt suggested long ago:
http://marc.info/?l=linux-kernel&m=119733290624544&w=2
This allows us to remove the IORESOURCE_PCI_FIXED hack from
pcibios_fixup_device_resources(), which converts bus addresses to CPU
addresses. IORESOURCE_PCI_FIXED denotes resources that can't be moved;
it has nothing to do with converting bus to CPU addresses.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linux-mips@linux-mips.org
Tested-by: Yoichi Yuasa <yuasa@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/998/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On Alchemy the PCMCIA area lies at the end of the chips 36bit system bus
area. Currently, addresses at the far end of the 32bit area are assumed
to belong to the PCMCIA area and fixed up to the real 36bit address before
being passed to ioremap().
A previous commit enabled 64 bit physical size for the resource datatype on
Alchemy and this allows to use the correct 36bit addresses when registering
the PCMCIA sockets.
This patch removes the 32-to-36bit address fixup and registers the Alchemy
demo board pcmcia socket with the correct 36bit physical addresses.
Tested on DB1200, with a CF card (ide-cs driver) and a 3c589 PCMCIA ethernet
card.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/994/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Because the VIA SuperIO chip only decodes 24 bits of address space but port
address space currently being configured as 32MB there is the theoretical
possibility of aliases within the I/O port address range.
The complicated solution is to reserve all address range that potencially
could cause such aliases. But with the PCI spec limiting port allocations
for devices to a maximum of 256 bytes 16MB of port address space already is
way more than one would ever expect to be used so we just reduce the port
space to 16MB.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: linux-mips@linux-mips.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Patchwork: http://patchwork.linux-mips.org/patch/995/
ALIGN(x, bytes) expands to __ALIGN_MASK(x, bytes - 1), so use the one
that is most clear.
Signed-off-by: Matt Turner <mattst88@gmail.com>
To: linux-mips@linux-mips.org
Cc: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/999/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is just a test program for raw_spinlocks. The main reason I
wrote it is to validate my spinlock changes that I sent in a previous
patch.
To use it enable CONFIG_DEBUG_FS and CONFIG_SPINLOCK_TEST then at run
time do:
# mount -t debugfs none /sys/kernel/debug/
# cat /sys/kernel/debug/mips/spin_single
# cat /sys/kernel/debug/mips/spin_multi
On my 600MHz octeon cn5860 (16 CPUs) I get
spin_single spin_multi
base 106885 247941
spinlock_patch 75194 219465
This shows that for uncontended locks the spinlock patch gives 41%
improvement and for contended locks 12% improvement (1/time).
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/969/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current locking mechanism uses a ll/sc sequence to release a
spinlock. This is slower than a wmb() followed by a store to unlock.
The branching forward to .subsection 2 on sc failure slows down the
contended case. So we get rid of that part too.
Since we are now working on naturally aligned u16 values, we can get
rid of a masking operation as the LHU already does the right thing.
The ANDI are reversed for better scheduling on multi-issue CPUs
On a 12 CPU 750MHz Octeon cn5750 this patch improves ipv4 UDP packet
forwarding rates from 3.58*10^6 PPS to 3.99*10^6 PPS, or about 11%.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/937/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Save/restore CPLD registers when doing suspend-to-ram; this fixes issues
with harddisk and ethernet not working correctly when resuming on DB1200.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/986/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Change to different macros for assembler macros since the old names in
powertv_setup.c were co-opted for use in asm/asm.h. This broken the
build for the powertv platform. This patch introduces new macros based on
the new macros in asm.h to take the place of the old macro values.
Signed-off-by: David VomLehn <dvomlehn@cisco.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/985/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The sole user is au1xxx_calc_clock() which is only used in early bootup
where the is no paralellism thus no race condition to protect against.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Manuel Lauss <manuel.lauss@googlemail.com>
The SmartMIPS ASE specifies how Read Inhibit (RI) and eXecute Inhibit
(XI) bits in the page tables work. The upper two bits of EntryLo{0,1}
are RI and XI when the feature is enabled in the PageGrain register.
SmartMIPS only covers 32-bit systems. Cavium Octeon+ extends this to
64-bit systems by continuing to place the RI and XI bits in the top of
EntryLo even when EntryLo is 64-bits wide.
Because we need to carry the RI and XI bits in the PTE, the layout of
the PTE is changed. There is a two instruction overhead in the TLB
refill hot path to get the EntryLo bits into the proper position.
Also the TLB load exception has to probe the TLB to check if RI or XI
caused the exception.
Also of note is that the layout of the PTE bits is done at compile and
runtime rather than statically. In the 32-bit case this allows for
the same number of PFN bits as before the patch as the _PAGE_HUGE is
not supported in 32-bit kernels (we have _PAGE_NO_EXEC and
_PAGE_NO_READ instead of _PAGE_READ and _PAGE_HUGE).
The patch is tested on Cavium Octeon+, but should also work on 32-bit
systems with the Smart-MIPS ASE.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/952/
Patchwork: http://patchwork.linux-mips.org/patch/956/
Patchwork: http://patchwork.linux-mips.org/patch/962/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The soon to follow Read Inhibit/eXecute Inhibit patch needs TLBR and
ROTR support in uasm. We also add a UASM_i_ROTR macro.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/953/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
64-bit CPUs have 64-bit c0_entrylo{0,1} registers. We should use the
64-bit dmtc0 instruction to set them. This becomes important if we
want to set the RI and XI bits present in some processors.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/954/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds a new DEBUG_ZBOOT option to allow the users to enable it
to debug the compressed kernel support for a new board and this optoin
should be disabled to reduce the kernel image size and speed up the
kernel booting procedure when the compressed kernel support is stable.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
To: Ralf Baechle <ralf@linux-mips.org>
Cc: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/918/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The function is #if 0ed out. There are no other occurrences of its
name in the tree. It is safe to remove.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/936/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It is not always used, even if it is available.
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/933/
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
[Ralf: Fixed up the rejects and changed all the new printk(KERN_...); to
pr_xxx() as suggested by Wu.]
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/920/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It is not always used, even if it is available.
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/893/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The userspace runtime linker uses the elf_platform to find the libraries
optimized for the current CPU archecture variant. First we need to allow it
to be set to something other than NULL. Follow-on patches will set some
values for specific CPUs.
GLIBC already does the right thing. The kernel just needs to supply good
data.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/891/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Although the hardware supports a 4/8bit SD interface and the driver
unconditionally advertises all hardware caps to the MMC core, not all
datalines may actually be wired up. This patch introduces another
field to au1xmmc platform data allowing platforms to disable certain
advanced host controller features.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: linux-mmc@vger.kernel.org
CC: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/460/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
AR7 has a larger physical offset than other MIPS based systems and therefore
needs to setup its handlers beyond the usual KSEG0 range. When running the
kernel in mapped mode this modification is also required. Remove function
comment which is now incorrect.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Eugene Konev <ejka@imfi.kspu.ru>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
To: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/889/
Patchwork: http://patchwork.linux-mips.org/patch/932/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All call sites of set_except_vector are already annotated with __init, so
annotate that one too.
Signed-off-by: Regards, Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
To: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/888/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
I believe these changes are needed on Alchemy SoCs in order to
use iomem above 4G with the usual platform_device machinery:
- Set CONFIG_ARCH_PHYS_ADDR_T_64BIT to make resource_size_t 64-bit.
- Increase IOMEM_RESOURCE_END so that platforms can register resources.
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/814/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In the old source code, I have let halt and poweroff do the same action,
but in reality, they have different meanings.
As the manpage of shutdown shows:
-r Reboot after shutdown.
-H Halt action is to halt or drop into boot monitor on systems that support it.
-P Halt action is to turn off the power.
and in the real world, some machines(e.g. NAS) did not provide a power
button and the shutdown works as reset, so, we need to provide a
mechanism to let the users turn off the power safely without breaking
the system, such a mechanism is "halt", which only put the system into a
dead loop or a power-save mode and print some information to the screen
to tell the users to turn off the power safely.
$ shutdown -hH now /* loongson_halt, not turn off the power */
$ shutdown -hP now /* loongson_poweroff, work as poweroff */
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Tested-by: Liu Shiwei <liushiwei@gmail.com>
Cc: Liu Shiwei <liushiwei@gmail.com>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/883/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Hook up the compressed debug output for all Alchemy systems supported
by current kernel codebase.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/879/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch makes the ar7 clock code implement the Linux clk API. Drivers
using the various clocks available in the SoC are updated accordingly.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
To: linux-mips@linux-mips.org
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: netdev@vger.kernel.org
Cc: David Miller <davem@davemloft.net>
Patchwork: http://patchwork.linux-mips.org/patch/881/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
To: linux-mips@linux-mips.org
To: Andrew Morton <akpm@linux-foundation.org>
To: LKML <linux-kernel@vger.kernel.org>
Patchwork: http://patchwork.linux-mips.org/patch/860/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For processors that have more than 64 TLBs, we need to decode both
config1 and config4 to determine the total number TLBs.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/866/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The function probe_tlb() only does anything for processors that are
not PRID_COMP_LEGACY. This is precisely the set of processors for
which decode_configs() is called to do identical tlbsize probing
calculations. Therefore probe_tlb() is completely redundant and may
be removed.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/865/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS currently lacks the readl_be and writel_be accessors
which are required by BCM63xx for OHCI and EHCI support.
Let's define them globally for MIPS. This also fixes the
compilation of the bcm63xx defconfig against USB.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@linux-mips.org
Cc: Maxime Bizon <mbizon@freebox.fr>
Patchwork: http://patchwork.linux-mips.org/patch/793/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Changes:
o Serial port related configuration
Disable EARLY_PRINTK, CONFIG_SYS_SUPPORTS_ZBOOT_UART16550
Enable the serial port support as module.
o PM related support
Enable CPUFreq as module, use the external timer(MFGPT) instead of
r4k timer.
Enable Suspend support
Enable Run Time PM support
o Enable SM7XX Video Driver
Disable the buggy 2d acceleration
o Enable CONFIG_OPROFILE as module
o Use GZIP instead of LZMA, which need less decompression time
o Enable more USB devices support
o Enable initrd support(needed by gNewsense)
o Enable more crypto support
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: yanh@lemote.com
Cc: huhb@lemote.com
Cc: zhangfx@lemote.com
Patchwork: http://patchwork.linux-mips.org/patch/830/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The compressed kernel support on loongson family machines is stable now,
so, remove the debug information via using SYS_SUPPORTS_ZBOOT instead of
SYS_SUPPORTS_ZBOOT_UART16550. This may reduce the image size and speedup
the booting.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: yanh@lemote.com
Cc: huhb@lemote.com
Cc: zhangfx@lemote.com
Patchwork: http://patchwork.linux-mips.org/patch/824/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Lemote have used the PMON_VER strings to indicate the loongson-2f
machine series:
PMON_VER=LM8089 Lemote 8.9'' netbook
LM8101 Lemote 10.1'' netbook
(The above two netbooks have the same kernel support)
LM6XXX Lemote FuLoong(2F) box series
LM9XXX Lemote LynLoong PC series
Before the machtype is supported by the PMON, we can get the machine
type from the PMON_VER for these machines, this will help the users a
lot.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: yanh@lemote.com
Cc: huhb@lemote.com
Cc: zhangfx@lemote.com
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/821/
Patchwork: http://patchwork.linux-mips.org/patch/908/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If an interrupt handler disables interrupts, the EOI function will
just reenable them. This will put us in an endless loop when the
upcoming Ethernet driver patches are applied.
Only reenable the interrupt on EOI if it is not IRQ_DISABLED. This
requires that the EOI function be separate from the ENABLE function.
We also rename the ACK functions to correspond with their function.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
To: gregkh@suse.de
Patchwork: http://patchwork.linux-mips.org/patch/840/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In order to achieve correct synchronization semantics, the Octeon port
had defined CONFIG_WEAK_REORDERING_BEYOND_LLSC. This resulted in code
that looks like:
sync
ll ...
.
.
.
sc ...
.
.
sync
The second SYNC was redundant, but harmless.
Octeon has a SYNCW instruction that acts as a write-memory-barrier
(due to an erratum in some parts two SYNCW are used). It is much
faster than SYNC because it imposes ordering on the writes, but
doesn't otherwise stall the execution pipeline. On Octeon, SYNC
stalls execution until all preceeding writes are committed to the
coherent memory system.
Using:
syncw;syncw
ll
.
.
.
sc
.
.
Has identical semantics to the first sequence, but is much faster.
The SYNCW orders the writes, and the SC will not complete successfully
until the write is committed to the coherent memory system. So at the
end all preceeding writes have been committed. Since Octeon does not
do speculative reads, this functions as a full barrier.
The patch removes CONFIG_WEAK_REORDERING_BEYOND_LLSC, and substitutes
SYNCW for SYNC in write-memory-barriers.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/850/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace some instances of smp_llsc_mb() with a new macro
smp_mb__before_llsc(). It is used before ll/sc sequences that are
documented as needing write barrier semantics.
The default implementation of smp_mb__before_llsc() is just smp_llsc_mb(),
so there are no changes in semantics.
Also simplify definition of smp_mb(), smp_rmb(), and smp_wmb() to be just
barrier() in the non-SMP case.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/851/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The smp_llsc_rmb() and smp_llsc_wmb() macros are not used in the tree,
remove them.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/848/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Implement reset / poweroff in the board code instead. The peripheral reset
code is gone too since YAMON which all in-tree boards use does the same
work when it boots.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/783/
Patchwork: http://patchwork.linux-mips.org/patch/882/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For 64-bit kernels with 64KB pages and two level page tables, there are
42 bits worth of virtual address space This is larger than the 40 bits of
virtual address space obtained with the default 4KB Page size and three
levels, so there are no draw backs for using two level tables with this
configuration.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/761/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the GPIO config symbol to only build Au1000 interrupt code on chips with
compatible hw.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/670/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the cpu subtype cpp macros in favor of runtime detection,
to improve compile coverage of the alchemy common code.
(Increases kernel size by 700 bytes).
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/699/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch makes the board code register the au1000-eth platform device. The
au1000-eth platform data can be overriden with the au1xxx_override_eth_cfg
function like it has to be done for the Bosporus board which uses a
different MAC/PHY setup.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: David Miller <davem@davemloft.net>
Cc: linux-mips@linux-mips.org
Cc: netdev@vger.kernel.org
Patchwork: http://patchwork.linux-mips.org/patch/618/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Machine driver for DB1200 AC97 and I2S audio systems, intended as a proper
reference asoc machine for Alchemy-based systems. AC97/I2S can be selected
at boot time by setting switch S6.7.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Cc: alsa-devel@alsa-project.org
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Create own directory for DB1200 code and update it with new features.
- SPI support:
- tmp121 temperature sensor
- SPI flash on DB1200
- I2C support
- NE1619 sensor
- AT24 eeprom
- I2C/SPI can be selected at boot time via switch S6.8
- Carddetect IRQs for SD cards.
- gen_nand based NAND support.
- hexleds count sleep/wake transitions.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace the devboard NOR MTD mapping driver with physmap-flash support.
Also honor the "swapboot" switch settings wrt. to the layout of the
NOR partitions.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Acked-By: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
UART autodetection breaks on the Au1300 but the IP blocks are identical,
at least according to the datasheets. Help the 8250 driver by passing
on uart type information via platform data.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Warnings being suppressed, we can now turn on -Werror for boards which did
not have it already (devboards and xss1500).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes warnings due to potentially unused
variables in board setup code or mixed variables
declaration and code (forbidden by ISO C90).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove unused uart bit definitions and base macros.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch replaces the general alchemy prom_putchar() implementation
in favor of board-specific versions: The UART where the output of
prom_putchar is directed to really depends on the board, the current
implementation hardcodes this on a per-SoC basis which is just wrong.
So a generic uart tx function is provided in the alchemy headers,
and the boards can provide their own prom_putchar with custom
destination uart, and all in-kernel alchemy boards support
early printk.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
DMA can only be done from physical addresses; move the "virt_to_phys"
source/destination buffer address translation from the dbdma queueing
functions (since the hardware can only DMA to/from physical addresses)
to their respective users.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove dbdma compat macros, move remaining users over to default
queueing functions and -flags.
(Queueing function signature has changed in order to give
a build failure instead of silent functional changes due
to the no longer implicitly specified DDMA_FLAGS_IE flag)
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
By replacing an extra do_IRQ with a goto, the assembly shrinks
from 260 to 212 bytes (gcc-4.3.4).
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Eliminate the sharing of IRQ names among the differenct Alchemy
variants. IRQ numbers need no longer be hidden behind a
CONFIG_SOC_AU1XXX symbol: step 1 in my quest to make the Alchemy
code less reliant on a hardcoded subtype.
This patch also renames the GPIO irq number constants. It's really
an interrupt line, NOT a GPIO number!
Code which relied on certain irq numbers to have the same name
across all supported cpu subtypes is changed to determine current
cpu subtype at runtime; in some places this isn't possible so
a "compat" symbol is used.
Run-tested on DB1200.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Raise RTCMATCH2 interrupt priority in case it is used as the system
timer tick.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Alchemy hardware provides a method to prioritize interrupts
on a controller by assigning them to a differenct core request line.
Assign usb device request interrupt to IC0 Request 0 (which has
highest priority in the core and the dispatcher) and others to
Request 1. The explicit check for usb device request occurrence
should be obsolete now.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Register the PCMCIA driver on all boards supported by it,
get rid of now-unused pcmcia macros in the board headers
(and subsequently empty pb1100/pb1500 ones).
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
New PCMCIA socket driver for all Db/Pb1xxx boards (except Pb1000),
which replaces au1000_db1x00.c and (most of) au1000_pb1x00.c.
Notable improvements:
- supports Db1000, DB/PB1100/1500/1550/1200.
- support for carddetect and statuschange IRQs.
- pcmcia socket mem/io/attr areas and irqs passed through
platform resource information.
- doesn't freeze system during card insertion/ejection like
the one it replaces.
- boardtype is automatically detected using BCSR ID register.
Run-tested on the DB1200.
Cc: Linux-PCMCIA <linux-pcmcia@lists.infradead.org>
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
remove board_init_irq(): On all in-kernel boards it is sufficient to
initialize board interrupts in an arch_initcall by using the default
linux irq functions.
Some small irqmap.c files have been folded into board_setup files.
Run-tested on DB1200; compile-tested on all other affected boards.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the PB1200 IRQ cascade code out to the BCSR support code:
upcoming DB1300 support can use it too.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All Alchemy development boards have external CPLDs with a few registers
in them. They all share an identical register layout with only a few
minor differences (except the PB1000) in bit functions and base
addresses.
This patch
- adds a primitive facility to initialize and use these external
registers,
- replaces all occurrences of bcsr->xxx accesses with calls to the new
functions (the pb1200 cascade irq handling code is special).
- collects BCSR register information scattered throughout the board
headers in a central place.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Merge commit aef55d4922 mis-merged io_apic.c so we lost the
arch_probe_nr_irqs() method.
This caused subtle boot breakages (udev confusion likely
due to missing drivers) with certain configs.
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20100207210250.GB8256@jenkins.home.ifup.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Enable NMI on all cpus in UV system and add an NMI handler
to dump_stack on each cpu.
By default on x86 all the cpus except the boot cpu have NMI
masked off. This patch enables NMI on all cpus in UV system
and adds an NMI handler to dump_stack on each cpu. This
way if a system hangs we can NMI the machine and get a
backtrace from all the cpus.
Version 2: Use x86_platform driver mechanism for nmi init, per
Ingo's suggestion.
Version 3: Clean up Ingo's nits.
Signed-off-by: Russ Anderson <rja@sgi.com>
LKML-Reference: <20100226164912.GA24439@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (362 commits)
V4L-DVB: cx88-dvb: remove extra attribution for core
V4L/DVB: v4l: soc_camera: fix bound checking of mbus_fmt[] index
V4L/DVB: Add support for SMT7020 to cx88
V4L/DVB: radio-si470x: Use UTF-8 encoding on a comment
V4L/DVB: MAINTAINERS: Telegent tlg2300 section fix
V4L/DVB: gspca_stv06xx: Add support for camera button
V4L/DVB: gspca_ov519: add support for the button on ov511 based cams
V4L/DVB: gspca_ov519: Add support for the button on ov518 based cams
V4L/DVB: gspca_ov519: add support for the button on ov519 based cams
V4L/DVB: gspca_main: Fix a compile error when CONFIG_INPUT is not set
V4L/DVB: gspca_main: some input error handling fixes
V4L/DVB: gspca_main: Allow use of input device creation code for non int. inputs
V4L/DVB: gspca_pac7302: much improved exposure control
V4L/DVB: gspca_sonixb: Make sonixb driver handle pas106 and pas202 cameras
V4L/DVB: gspca_sonixb: pas106: fixup bright ctrl and add gain and exposure ctrls
V4L/DVB: Documentation: gspca.txt: update known mr97310a cams
V4L/DVB: gspca_mr97310a: add support for the Sakar 1638x CyberPix
V4L/DVB: gscpa_sonixb: limit ov7630 max framerate at 640x480
V4L/DVB: gspca_sonixb: pas202: fixup brightness ctrl and add gain and exposure ctrls
V4L/DVB: gscpa_sonixb: Differentiate between sensors with a coarse and fine expo ctrl
...
* 'kmemcheck-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
kmemcheck: Test the full object in kmemcheck_is_obj_initialized()
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/xfs-vipt:
xfs: fix xfs to work with Virtually Indexed architectures
sh: add mm API for DMA to vmalloc/vmap areas
arm: add mm API for DMA to vmalloc/vmap areas
parisc: add mm API for DMA to vmalloc/vmap areas
mm: add coherence API for DMA to vmalloc/vmap areas
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (187 commits)
sh: remove dead LED code for migo-r and ms7724se
sh: ecovec build fix for CONFIG_I2C=n
sh: ecovec r-standby support
sh: ms7724se r-standby support
sh: SH-Mobile R-standby register save/restore
clocksource: Fix up a registration/IRQ race in the sh drivers.
sh: ms7724: modify scan_timing for KEYSC
sh: ms7724: Add sh_sir support
sh: mach-ecovec24: Add sh_sir support
sh: wire up SET/GET_UNALIGN_CTL.
sh: allow alignment fault mode to be configured at kernel boot.
sh: sh7724: Update FSI/SPU2 clock
sh: always enable sh7724 vpu_clk and set to 166MHz on Ecovec
sh: add sh7724 kick callback to clk_div4_table
sh: introduce struct clk_div4_table
sh: clock-cpg div4 set_rate() shift fix
sh: Turn on speculative return for SH7785 and SH7786
sh: Merge legacy and dynamic PMB modes.
sh: Use uncached I/O helpers in PMB setup.
sh: Provide uncached I/O helpers.
...
The glibc vdso code for s390 uses the version string 2.6.29, the
kernel uses the version string 2.6.26. No wonder the vdso code
is never used. The first kernel version to contain the vdso code
is 2.6.29 which makes this the correct version.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add the "bzImage" compile target and the necessary code to generate
compressed kernel images. The old style uncompressed "image" target
is preserved, a simple make will build them both.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move the ebcdic to ascii conversion of the kernel parameter line from
head.S to early.c and convert the assembler code to C.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add the instruction of the z9-ec and z10 machines to the kernel disassembler.
Add the missing "ptff" instruction of z9-109 and the missing "sqd" of g5.
Remove useless comments with instruction examples from format table.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use kprobes_built_in() to avoid ifdefs like most other architectures do.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reduces the size of the bug table entries by 50% on 64bit kernels.
Saves around 30kb on a defconfig kernel.
s390 version of b93a531e "allow bug table entries to use relative
pointers (and use it on x86-64)".
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use asm offsets to make sure the offset defines to struct _lowcore and
its layout don't get out of sync.
Also add a BUILD_BUG_ON() which checks that the size of the structure
is sane.
And while being at it change those sites which use odd casts to access
the current lowcore. These should use S390_lowcore instead.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
free_initmem() and free_initrd_mem() are nearly identical. So make them
call a common function.
Also fixes a bug: if the initrd wouldn't start on a page boundary also
memory after the initrd would be initialized with the poison value.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
ENOTSUPP is not supposed to leak to userspace so lets just use
EOPNOTSUPP everywhere.
Doesn't fix a bug, but makes future reviews easier.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch introduces a new function that checks the running status
of a cpu in a hypervisor. This status is not virtualized, so the check
is only correct if running in an LPAR. On acquiring a spinlock, if the
cpu holding the lock is scheduled by the hypervisor, we do a busy wait
on the lock. If it is not scheduled, we yield over to that cpu.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The size of the field that contains the description block count is
only four bits instead of eight bits.
The first four bits are reserved but this might change and break.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce the MACHINE_IS_LPAR flag for code that should only be
executed if Linux is running in an LPAR.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove a memset hack that relied on the internal layout of the
qdio_irq struct and move the per device statistics data into an own
cache line to avoid cache line bashing between the inbound and the
outbound queue tasklets. Also reduce the number of allocated queues
from 32 to 4 which is the current maximum. That saves a cache line
in struct qdio_irq.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Rename signal_processor* functions to sigp*.
Add raw variants of each version, so we can get rid of the hacks played
in smp code which establish temporary cpu logical mappings so they could
call the sigp functions.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Always reboot on logical cpu 0. This makes sure that the IPL cpu is
always the same and usually avoids strange numbering schemes between
physical and logical cpus.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Rename __LC_RESTART_PSW to __LC_RST_NEW_PSW, add a define for the
missing 32 bit variant and the missing old PSWs.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove support to be able to dump 31 bit systems with a 64 bit dumper.
This is mostly useless since no distro ships 31 bit kernels together
with a 64 bit dumper.
We also get rid of a bit of hacky code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Drop support to compile the kernel with gcc versions older than 3.3.3.
This allows us to use the "Q" inline assembly contraint on some more
inline assemblies without duplicating a lot of complex code (e.g. __xchg
and __cmpxchg). The distinction for older gcc versions can be removed
which saves a few lines and simplifies the code.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Some parts of cio do not shift PAGE_DEFAULT_KEY correctly and end up
with an incorrect key in their data structures.
Since the default key is zero this doesn't really matter. However if
somebody would use key-controlled protection for debugging purposes
it would be quite helpful if all of this would work as expected.
Also remove a stale declaration.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
To fetch a pending channel report word (crw) we use a kernel
thread which triggers stcrw and sleeps on a semaphore. The s390
machine check handler uses crw_handle_channel_report to handle
one crw if needed.
This patch replaces the semaphore with a waitqueue (to block the
kernel thread) and an atomic_t (to count the number of pending
requests).
By this we achieve the ability to force this thread to check for
a pending crw (independent on when it is triggered by the machine
check handler) and wait for this action to finish.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Same as on x86 and sparc, besides the fact that enabling the option
will just emit compile time warnings instead of errors.
Keeps allyesconfig kernels compiling.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
n_val should be assigned to n_val attribute of HUB chip.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
ia64 parts of system wide cleanup to drop trailing whitespace
from lines in message strings.
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Tony Luck <tony.luck@intel.com>
IA64's scatterlist structure is identical to the generic one.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (48 commits)
x86/PCI: Prevent mmconfig memory corruption
ACPI: Use GPE reference counting to support shared GPEs
x86/PCI: use host bridge _CRS info by default on 2008 and newer machines
PCI: augment bus resource table with a list
PCI: add pci_bus_for_each_resource(), remove direct bus->resource[] refs
PCI: read bridge windows before filling in subtractive decode resources
PCI: split up pci_read_bridge_bases()
PCIe PME: use pci_pcie_cap()
PCI PM: Run-time callbacks for PCI bus type
PCIe PME: use pci_is_pcie()
PCI / ACPI / PM: Platform support for PCI PME wake-up
ACPI / ACPICA: Multiple system notify handlers per device
ACPI / PM: Add more run-time wake-up fields
ACPI: Use GPE reference counting to support shared GPEs
PCI PM: Make it possible to force using INTx for PCIe PME signaling
PCI PM: PCIe PME root port service driver
PCI PM: Add function for checking PME status of devices
PCI: mark is_pcie obsolete
PCI: set PCI_PREF_RANGE_TYPE_64 in pci_bridge_check_ranges
PCI: pciehp: second try to get big range for pcie devices
...
This patch adds following changes:-
1) add sub device configuration data for TVP5146 used by vpfe capture
2) registers platform devices for vpfe_capture, isif and vpss
3) defines hardware resources for the devices listed under 2)
4) defines clock aliase for isif driver
5) adding setup_pinmux() for isif
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Murali Karicheri <mkaricheri@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pxa_camera init() callback is sometimes abused to setup MFP for PXA CIF, or
even to request GPIOs to be used by the camera *sensor*. These initializations
can be performed statically in machine init functions.
The current semantics for this init() callback is ambiguous anyways, it is
invoked in pxa_camera_activate(), hence at device node open, but its users use
it like a generic initialization to be done at module init time (configure
MFP, request GPIOs for *sensor* control).
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes "buswidth" struct member, and sets the default buswidth
to the natively supported 10 bit. You can select 8 bit buswidth by new flag.
This patch also modify ap325rxa/migor setup.c
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Split amd,p6,intel into separate files so that we can easily deal with
CONFIG_CPU_SUP_* things, needed to make things build now that perf_event.c
relies on symbols from amd.c
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
During switching virtual counters there is access to perfctr msrs. If
the counter is not available this fails due to an invalid
address. This patch fixes this.
Cc: stable@kernel.org
Signed-off-by: Robert Richter <robert.richter@amd.com>
Multiple virtual counters share one physical counter. The reservation
of virtual counters fails due to duplicate allocation of the same
counter. The counters are already reserved. Thus, virtual counter
reservation may removed at all. This also makes the code easier.
Cc: stable@kernel.org
Signed-off-by: Robert Richter <robert.richter@amd.com>
Currently, oprofile fails silently on platforms where a non-OS entity
such as the system firmware "enables" and uses a performance
counter. There is a warning in the code for this case.
The warning indicates an already running counter. If oprofile doesn't
collect data, then try using a different performance counter on your
platform to monitor the desired event. Delete the counter from the
desired event by editing the
/usr/share/oprofile/<cpu_type>/<cpu>/events
file. If the event cannot be monitored by any other counter, contact
your hardware or BIOS vendor.
Cc: Shashi Belur <shashi-kiran.belur@hp.com>
Cc: Tony Jones <tonyj@suse.de>
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
This patch generates a warning if a counter is already active.
Implemented for AMD and P6 models. P4 is not supported.
Cc: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Cc: Shashi Belur <shashi-kiran.belur@hp.com>
Cc: Tony Jones <tonyj@suse.de>
Signed-off-by: Robert Richter <robert.richter@amd.com>
IBS selects an op (execution operation) for sampling by counting
either cycles or dispatched ops. Better statistical samples can be
produced by adding a software generated random offset to the periodic
op counter value with each sample.
This patch adds software randomization to the IBS periodic op
counter. The lower 12 bits of the 20 bit counter are
randomized. IbsOpCurCnt is initialized with a 12 bit random value.
There is a work around if the hw can not write to IbsOpCurCnt. Then
the lower 8 bits of the 16 bit IbsOpMaxCnt [15:0] value are randomized
in the range of -128 to +127 by adding/subtracting an offset to the
maximum count (IbsOpMaxCnt).
The linear feedback shift register (LFSR) algorithm is used for
pseudo-random number generation to have low impact to the memory
system.
Signed-off-by: Robert Richter <robert.richter@amd.com>
This patch implements a linear feedback shift register (LFSR) for
pseudo-random number generation for IBS.
For IBS measurements it would be good to minimize memory traffic in
the interrupt handler since every access pollutes the data
caches. Computing a maximal period LFSR just needs shifts and ORs.
The LFSR method is good enough to randomize the ops at low
overhead. 16 pseudo-random bits are enough for the implementation and
it doesn't matter that the pattern repeats with a fairly short
cycle. It only needs to break up (hard) periodic sampling behavior.
The logic was designed by Paul Drongowski.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
This patch adds IBS feature detection using cpuid flags. An IBS
capability mask is introduced to test for certain IBS features. The
bit mask is the same as for IBS cpuid feature flags (Fn8000_001B_EAX),
but bit 0 is used to indicate the existence of IBS.
The patch also changes the handling of the IbsOpCntCtl bit (periodic
op counter count control). The oprofilefs file for this feature
(ibs_op/dispatched_ops) will be only exposed if the feature is
available, also the default for the bit is set to count clock cycles.
In general, the userland can detect the availability of a feature by
checking for the corresponding file in oprofilefs. If it exists, the
feature also exists. This may lead to a dynamic file layout depending
on the cpu type with that the userland has to deal with. Current
opcontrol is compatible.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Standard AMD systems have the same number of nodes as there are
northbridge devices. However, there may kernel configurations
(especially for 32 bit) or system setups exist, where the node number
is different or it can not be detected properly. Thus the check is not
reliable and may fail though IBS setup was fine. For this reason it is
better to remove the check.
Cc: stable <stable@kernel.org>
Signed-off-by: Robert Richter <robert.richter@amd.com>
OProfile support for IBS is now for several versions in the
kernel. The feature is stable now and the code can be activated
permanently.
As a side effect IBS now works also on nosmp configs.
Signed-off-by: Robert Richter <robert.richter@amd.com>
The commit
1155de4 ring-buffer: Make it generally available
already made ring-buffer available without the TRACING option
enabled. This patch removes the TRACING dependency from oprofile.
Fixes also oprofile configuration on ia64.
The patch also applies to the 2.6.32-stable kernel.
Reported-by: Tony Jones <tonyj@suse.de>
Cc: stable@kernel.org
Signed-off-by: Robert Richter <robert.richter@amd.com>
Except for SCSI no device drivers distinguish between physical and
hardware segment limits. Consolidate the two into a single segment
limit.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The block layer calling convention is blk_queue_<limit name>.
blk_queue_max_sectors predates this practice, leading to some confusion.
Rename the function to appropriately reflect that its intended use is to
set max_hw_sectors.
Also introduce a temporary wrapper for backwards compability. This can
be removed after the merge window is closed.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
sparc's scatterlist structure is identical to the generic one.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
We re-program the event control register every time we reset the count,
this appears to be superflous, hence remove it.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arjan van de Ven <arjan@linux.intel.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since the cpu argument to hw_perf_group_sched_in() is always
smp_processor_id(), simplify the code a little by removing this argument
and using the current cpu where needed.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: David Miller <davem@davemloft.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <1265890918.5396.3.camel@laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds correct AMD NorthBridge event scheduling.
NB events are events measuring L3 cache, Hypertransport traffic. They are
identified by an event code >= 0xe0. They measure events on the
Northbride which is shared by all cores on a package. NB events are
counted on a shared set of counters. When a NB event is programmed in a
counter, the data actually comes from a shared counter. Thus, access to
those counters needs to be synchronized.
We implement the synchronization such that no two cores can be measuring
NB events using the same counters. Thus, we maintain a per-NB allocation
table. The available slot is propagated using the event_constraint
structure.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <4b703957.0702d00a.6bf2.7b7d@mx.google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In certain situations, the kernel may need to stop and start the same
event rapidly. The current PMU callbacks do not distinguish between stop
and release (i.e., stop + free the resource). Thus, a counter may be
released, then it will be immediately re-acquired. Event scheduling will
again take place with no guarantee to assign the same counter. On some
processors, this may event yield to failure to assign the event back due
to competion between cores.
This patch is adding a new pair of callback to stop and restart a counter
without actually release the underlying counter resource. On stop, the
counter is stopped, its values saved and that's it. On start, the value
is reloaded and counter is restarted (on x86, actual restart is delayed
until perf_enable()).
Signed-off-by: Stephane Eranian <eranian@google.com>
[ added fallback to ->enable/->disable for all other PMUs
fixed x86_pmu_start() to call x86_pmu.enable()
merged __x86_pmu_disable into x86_pmu_stop() ]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <4b703875.0a04d00a.7896.ffffb824@mx.google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Anton's commit enabling the use of the lwsync fixup mechanism on 64-bit
breaks modules. The lwsync fixup section uses .long instead of the
FTR_ENTRY_OFFSET macro used by other fixups sections, and thus will
generate 32-bit relocations that our module loader cannot resolve.
This changes it to use the same type as other feature sections.
Note however that we might want to consider using 32-bit for all the
feature fixup offsets and add support for R_PPC_REL32 to module_64.c
instead as that would reduce the size of the kernel image. I'll leave
that as an exercise for the reader for now...
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CONFIG_PM is always set on SH-Mobile these days so
get rid of the unused LED setup code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Allow building the ecovec board support code
even though I2C support is disabled.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds board specific r-standby resume code
for ecovec.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds board specific r-standby resume code
for ms7724se.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add code to save/restore registers during
R-standby sleep on SH-Mobile processors.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (41 commits)
of: remove undefined request_OF_resource & release_OF_resource
of/sparc: Remove sparc-local declaration of allnodes and devtree_lock
of: move definition of of_chosen into common code.
of: remove unused extern reference to devtree_lock
of: put default string compare and #a/s-cell values into common header
of/flattree: Don't assume HAVE_LMB
of: protect linux/of.h with CONFIG_OF
proc_devtree: fix THIS_MODULE without module.h
of: Remove old and misplaced function declarations
of/flattree: Make the kernel accept ePAPR style phandle information
of/flattree: endian-convert members of boot_param_header
of: assume big-endian properties, adding conversions where necessary
of: use __be32 for cell value accessors
of/flattree: use OF_ROOT_NODE_{SIZE,ADDR}_CELLS DEFAULT for fdt parsing
of/flattree: use callback to setup initrd from /chosen
proc_devtree: include linux/of.h
of: make set_node_proc_entry private to proc_devtree.c
of: include linux/proc_fs.h
of/flattree: merge early_init_dt_scan_memory() common code
of: add 'of_' prefix to machine_is_compatible()
...
Simplify the makefile slightly by always building acpi-ext.o when
CONFIG_ACPI is turned on.
Yes, this adds a little bloat to the other configs, but not much:
text data bss dec hex filename
839 41 0 880 370 arch/ia64/kernel/acpi-ext.o
Before:
text data bss dec hex filename
10952753 1299212 1334241 13586206 cf4f1e vmlinux
After:
text data bss dec hex filename
10953739 1299084 1334241 13587064 cf5278 vmlinux
(gdb) p 13587064 - 13586206
$2 = 858
Seems like a small price to pay for the benefit of not having to think
so hard about the multitude of ia64 configs when reading code/Makefiles.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch changes the 32-bit version of kernel_physical_mapping_init() to
return the last mapped address like the 64-bit one so that we can unify the
call-site in init_memory_mapping().
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
LKML-Reference: <alpine.DEB.2.00.1002241703570.1180@melkki.cs.helsinki.fi>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The following commit broke the ia64 sim_defconfig build:
3b2b84c0b81108a9a869a88bf2beeb5a95d81dd1
ACPI: processor: driver doesn't need to evaluate _PDC
This is because it added:
+#include <acpi/processor.h>
To arch/ia64/kernel/acpi.c. Unfortunately, the ia64_simdefconfig does
not turn on CONFIG_ACPI, and we get build errors.
The fix described in $subject seems to be the most sensible way to
untangle the mess.
The other issue is that acpi_get_sysname() is required for all configs,
most of which define CONFIG_ACPI, but are not CONFIG_IA64_GENERIC. Turn
it into an inline to cover the "non generic" ia64 configs; to prevent
a duplicate definition build error, we need to wrap the definition in
acpi.o inside an #ifdef.
Finally, move the pm_idle and pm_power_off exports into process.c (which
is always built), similar to other architectures, and allow the sim
defconfig to link.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Correct instances where tca6416 is misspelt as tca6516 in
the board-am3517evm file.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are multiple devices connected to I2C bus on AM3517EVM
(for instance audio codec, IO expander etc). Enable I2C support
in the default kernel configuration for AM3517 EVM.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enabling OMAP_MUX in defconfig as it is required for EHCI to work.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding GPIO mux config used for PHY reset of EHCI port on base board.
We get below failure message without this patch,
"hub 1-0:1.0: unable to enumerate USB device on port 1"
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some of the features are not enabled by default in zoom3 defconfig.
This patch enables:
- MMC Resume
- TWL4030 RTC driver
- Debug File system
Build and boot tested on Zoom3 board.
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The commit b63128e812 broke the pin muxing
for I2C busses that are enabled from the kernel command line.
Fix this by defining the board registration function omap_register_i2c_bus
in common platform code as it was before but keep the muxing in architecture
dependent files.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We used to build decompressors with -Dstatic= to avoid any local data
being generated. The problem is that local data generates GOTOFF
relocations, which means we can't relocate the data relative to the
text segment.
Global data, on the other hand, goes through the GOT, and can be
relocated anywhere.
Unfortunately, with the new decompressors, this presents a problem
since they declare static data within functions, and this leads to
stack overflow.
Fix this by separating out the decompressor code into a separate file,
and removing 'static' from BSS data in misc.c.
Also, discard the .data section - this means that should we end up
with read/write initialized data, the decompressor will fail to link
and the problem will be obvious.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Introduce x86 arch-specific optimization code, which supports
both of x86-32 and x86-64.
This code also supports safety checking, which decodes whole of
a function in which probe is inserted, and checks following
conditions before optimization:
- The optimized instructions which will be replaced by a jump instruction
don't straddle the function boundary.
- There is no indirect jump instruction, because it will jumps into
the address range which is replaced by jump operand.
- There is no jump/loop instruction which jumps into the address range
which is replaced by jump operand.
- Don't optimize kprobes if it is in functions into which fixup code will
jumps.
This uses text_poke_multibyte() which doesn't support modifying
code on NMI/MCE handler. However, since kprobes itself doesn't
support NMI/MCE code probing, it's not a problem.
Changes in v9:
- Use *_text_reserved() for checking the probe can be optimized.
- Verify jump address range is in 2G range when preparing slot.
- Backup original code when switching optimized buffer, instead of
preparing buffer, because there can be int3 of other probes in
preparing phase.
- Check kprobe is disabled in arch_check_optimized_kprobe().
- Strictly check indirect jump opcodes (ff /4, ff /5).
Changes in v6:
- Split stop_machine-based jump patching code.
- Update comments and coding style.
Changes in v5:
- Introduce stop_machine-based jump replacing.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: systemtap <systemtap@sources.redhat.com>
Cc: DLE <dle-develop@lists.sourceforge.net>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Anders Kaseorg <andersk@ksplice.com>
Cc: Tim Abbott <tabbott@ksplice.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Mathieu Desnoyers <compudj@krystal.dyndns.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
LKML-Reference: <20100225133446.6725.78994.stgit@localhost6.localdomain6>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add generic text_poke_smp for SMP which uses stop_machine()
to synchronize modifying code.
This stop_machine() method is officially described at "7.1.3
Handling Self- and Cross-Modifying Code" on the intel's
software developer's manual 3A.
Since stop_machine() can't protect code against NMI/MCE, this
function can not modify those handlers. And also, this function
is basically for modifying multibyte-single-instruction. For
modifying multibyte-multi-instructions, we need another special
trap & detour code.
This code originaly comes from immediate values with
stop_machine() version. Thanks Jason and Mathieu!
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: systemtap <systemtap@sources.redhat.com>
Cc: DLE <dle-develop@lists.sourceforge.net>
Cc: Mathieu Desnoyers <compudj@krystal.dyndns.org>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Anders Kaseorg <andersk@ksplice.com>
Cc: Tim Abbott <tabbott@ksplice.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
LKML-Reference: <20100225133438.6725.80273.stgit@localhost6.localdomain6>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Introduce kprobes jump optimization arch-independent parts.
Kprobes uses breakpoint instruction for interrupting execution
flow, on some architectures, it can be replaced by a jump
instruction and interruption emulation code. This gains kprobs'
performance drastically.
To enable this feature, set CONFIG_OPTPROBES=y (default y if the
arch supports OPTPROBE).
Changes in v9:
- Fix a bug to optimize probe when enabling.
- Check nearby probes can be optimize/unoptimize when disarming/arming
kprobes, instead of registering/unregistering. This will help
kprobe-tracer because most of probes on it are usually disabled.
Changes in v6:
- Cleanup coding style for readability.
- Add comments around get/put_online_cpus().
Changes in v5:
- Use get_online_cpus()/put_online_cpus() for avoiding text_mutex
deadlock.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: systemtap <systemtap@sources.redhat.com>
Cc: DLE <dle-develop@lists.sourceforge.net>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Anders Kaseorg <andersk@ksplice.com>
Cc: Tim Abbott <tabbott@ksplice.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Mathieu Desnoyers <compudj@krystal.dyndns.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
LKML-Reference: <20100225133407.6725.81992.stgit@localhost6.localdomain6>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
commit ff097ddd4 (x86/PCI: MMCONFIG: manage pci_mmcfg_region as a
list, not a table) introduced a nasty memory corruption when
pci_mmcfg_list is empty.
pci_mmcfg_check_end_bus_number() dereferences pci_mmcfg_list.prev even
when the list is empty. The following write hits some variable near to
pci_mmcfg_list.
Further down a similar problem exists, where cfg->list.next is
dereferenced unconditionally and a comparison with some variable near
to pci_mmcfg_list happens.
Add a check for the last element into the for_each_entry() loop and
remove all the other crappy logic which is just a leftover of the old
array based code which was replaced by the list conversion.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The code in stop_machine that modifies the kernel text has a bit
of logic to handle the case of NMIs. stop_machine does not prevent
NMIs from executing, and if an NMI were to trigger on another CPU
as the modifying CPU is changing the NMI text, a GPF could result.
To prevent the GPF, the NMI calls ftrace_nmi_enter() which may
modify the code first, then any other NMIs will just change the
text to the same content which will do no harm. The code that
stop_machine called must wait for NMIs to finish while it changes
each location in the kernel. That code may also change the text
to what the NMI changed it to. The key is that the text will never
change content while another CPU is executing it.
To make the above work, the call to ftrace_nmi_enter() must also
do a smp_mb() as well as atomic_inc(). But for applications like
perf that require a high number of NMIs for profiling, this can have
a dramatic effect on the system. Not only is it doing a full memory
barrier on both nmi_enter() as well as nmi_exit() it is also
modifying a global variable with an atomic operation. This kills
performance on large SMP machines.
Since the memory barriers are only needed when ftrace is in the
process of modifying the text (which is seldom), this patch
adds a "modifying_code" variable that gets set before stop machine
is executed and cleared afterwards.
The NMIs will check this variable and store it in a per CPU
"save_modifying_code" variable that it will use to check if it
needs to do the memory barriers and atomic dec on NMI exit.
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Distros generally (I looked at Debian, RHEL5 and SLES11) seem to
enable CONFIG_HIGHPTE for any x86 configuration which has highmem
enabled. This means that the overhead applies even to machines which
have a fairly modest amount of high memory and which therefore do not
really benefit from allocating PTEs in high memory but still pay the
price of the additional mapping operations.
Running kernbench on a 4G box I found that with CONFIG_HIGHPTE=y but
no actual highptes being allocated there was a reduction in system
time used from 59.737s to 55.9s.
With CONFIG_HIGHPTE=y and highmem PTEs being allocated:
Average Optimal load -j 4 Run (std deviation):
Elapsed Time 175.396 (0.238914)
User Time 515.983 (5.85019)
System Time 59.737 (1.26727)
Percent CPU 263.8 (71.6796)
Context Switches 39989.7 (4672.64)
Sleeps 42617.7 (246.307)
With CONFIG_HIGHPTE=y but with no highmem PTEs being allocated:
Average Optimal load -j 4 Run (std deviation):
Elapsed Time 174.278 (0.831968)
User Time 515.659 (6.07012)
System Time 55.9 (1.07799)
Percent CPU 263.8 (71.266)
Context Switches 39929.6 (4485.13)
Sleeps 42583.7 (373.039)
This patch allows the user to control the allocation of PTEs in
highmem from the command line ("userpte=nohigh") but retains the
status-quo as the default.
It is possible that some simple heuristic could be developed which
allows auto-tuning of this option however I don't have a sufficiently
large machine available to me to perform any particularly meaningful
experiments. We could probably handwave up an argument for a threshold
at 16G of total RAM.
Assuming 768M of lowmem we have 196608 potential lowmem PTE
pages. Each page can map 2M of RAM in a PAE-enabled configuration,
meaning a maximum of 384G of RAM could potentially be mapped using
lowmem PTEs.
Even allowing generous factor of 10 to account for other required
lowmem allocations, generous slop to account for page sharing (which
reduces the total amount of RAM mappable by a given number of PT
pages) and other innacuracies in the estimations it would seem that
even a 32G machine would not have a particularly pressing need for
highmem PTEs. I think 32G could be considered to be at the upper bound
of what might be sensible on a 32 bit machine (although I think in
practice 64G is still supported).
It's seems questionable if HIGHPTE is even a win for any amount of RAM
you would sensibly run a 32 bit kernel on rather than going 64 bit.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
LKML-Reference: <1266403090-20162-1-git-send-email-ian.campbell@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This will save 64K bytes from memory when loading linux if DMI is
disabled, which is good for embedded systems.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
LKML-Reference: <1265758732-19320-1-git-send-email-cascardo@holoscopio.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
KEYSC::SCN register of SH7724 is 3bit.
Thus, scan_timing should be 0 - 7 here.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
