We need to count the timeout down.
Reported-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Fix below build warning:
sound/soc/blackfin/bf5xx-ad73311.c: warning: initialization from incompatible pointer type
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
clk_get() returns a pointer to the struct clk or an ERR_PTR().
This patch also use PTR_ERR() for return value.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Freescale SSI audio controller supports "synchronous" and "asynchronous"
modes. In synchronous mode, playback and capture use the same input clock,
so sample rates must be the same during simultaneous playback and capture.
Unfortunately, the code which supports asynchronous mode is just broken in
various ways. In particular, it was constraining sample sizes as well as
the sample rate.
The fix also allows us to simplify the code by eliminating the 'asynchronous',
'playback', and 'capture' variables that were used to keep track of playback
and capture streams.
Unfortunately, it turns out that simulataneous playback and record does not
actually work on the only platform that supports asynchronous mode: the
Freescale P1022DS reference board. If a second stream is started, the SSI
grinds to halt for both streams. This is true even if the P1022 is configured
for synchronous mode, so it's likely a hardware problem that needs to be
worked around.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The AIF1 channels are numbered from zero than one; do the same thing for
AIF2 too.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The WM8996 only requires CPVDD when the charge pump is active so control
it separately to the other supplies, only enabling it when the charge pump
is active. This will result in a small power saving on systems which are
able to provide independent software control of the supply.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
A fix merged in 3.1-rc2 introduced a small regression, this should get it
to build again.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently register read-back for the ad193x is broken, because it expects bit 0
of the upper byte to be set to indicate a read operation, while the regmap
default for SPI is to use bit 7.
This patch also addresses another oddity of the device. There are SPI and I2C
versions of this codec. In both cases the registers are 8-bit wide and numbered
from 0x0 to 0x10, but in the SPI case there is also a so called
'global address' which is prefixed in-front of the register address. The global
address mimics I2C behaviour and includes a static device address the and the
read/write flag. This basically extends the register address to an 16-bit value
numbered from 0x800 to 0x810. These are the register numbers which are
currently used by the driver. This works, because I2C will ignore the upper
8 bits of the register, but it is still a bit confusing, as there are no such
register numbers in the I2C case.
The approach taken by this patch is to number the registers from 0x00 to 0x10
and encode the global address for SPI mode into the read and write flag masks.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Return proper error instead of 0 if clk_get fails.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
snd_pcm_hw_constraint_integer() could return -1, in this case, sst platform is
not opened successfully. However the corresponding close callback isn't able
to be called later on to release these two allocated memories, thus resulting
in memory leak.
This patch moves the check for hardware contraints earlier, thus resolving this
issue.
Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the builtin snd_soc_set_runtime_hwparams() instead of assigning it by
myself.
Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Return -ENODEV instead of 0 if vendor id mismatch.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We don't use the step size so there's no need to work it out.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
We can directly read the FLL lock status on WM8996 so even if we don't
have an interrupt wired up we can still verify that the FLL started
successfully.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix the codec_name field of the dai_link to match the actual device name
of the codec. Otherwise the card won't be instantiated.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
We need to report the entire jack state to the core jack code, not just
the bits that were being updated by the caller, otherwise the status
reported by other detection methods will be omitted from the state seen
by userspace.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@kernel.org
In the case of no free channel available,
current implementation returns 0 instead of negative errno.
This patch fixes the logic to return -EINVAL if no free channel available.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Similarly to PLLs/FLLs some modern CODECs provide selectable system clock
sources. When the clock is the clock for a DAI we do not usually need to
identify which clock is being configured so can use clk_id for the source
clock but with CODEC wide system clocks we will need to specify both the
clock being configured and the source.
Add a source argument to the CODEC driver set_sysclk() operation to
reflect this. As this operation is not as widely used as the DAI
set_sysclk() operation the change is not very invasive. We probably
ought to go and make the same alternation for DAIs at some point.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fixes the following warning:
CC sound/soc/imx/imx-pcm-fiq.o
sound/soc/imx/imx-pcm-fiq.c: In function 'imx_pcm_fiq_new':
sound/soc/imx/imx-pcm-fiq.c:243: warning: unused variable 'card'
CC sound/soc/imx/imx-pcm-dma-mx2.o
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_codec_readable_register instead of open-coding it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently the condition for these WARN_ONs is reversed and they are placed
before the actual check whether we are going to write to that register. So if
the codec implements the register_writable callback we'll get a warning for each
writable register when syncing the register cache.
While we are at it change the check to use snd_soc_codec_writable_register
instead of open-coding it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Change the default return value of snd_soc_codec_{readable,writable}_register to
true when no codec specific callback for this function is given. Otherwise all
registers of that codec will neither be readable nor writable, which is most
certainly not what we want.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We have dapm_context instead of codec parameter.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Replace the channels_min check with a check for the relevant substream
being present. Suggested here [1] when mxs implemented the
audio-support.
[1] http://www.spinics.net/lists/arm-kernel/msg133010.html
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the channel is allocated as writecombine, then mmaping it should also
use writecombine. Also, add a proper device for the call. Ported from a
similar fix for mach-mxs.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
My first patch to ASoC ever! If I did something wrong, blame Ian.
Signed-off-by: Susan Gao <sgao@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Although the McASP supports sign-extending samples in RX or TX [1]; the
davinci-mcasp driver does not touch the {R,X}PBIT or {R,X}PAD field of the
{R,X}FMT registers meaning that the McASP will serialize the bytes it is given
regardless of their signedness. So supporting unsigned formats is as simple
as adding them to the metadata of the davinci-mcasp driver.
Update the FMTBITs reported in the snd_soc_dai_driver and also update the case
statements in davinci-mcasp's hw_params() function so that the McASP can be
connected to CODECs that use unsigned values.
[1] http://www.ti.com/lit/ug/sprufm1/sprufm1.pdf
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
'struct of_device' no longer exists, and its functionality has been merged
into platform_device. Update the MPC5200 audio DMA driver (mpc5200_dma)
accordingly. This fixes a build break.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
This patch adds Kconfig to support SMDK4212.
SMDK4212 is based on samsung exynos4212 SoC.
And WM8994 is used for audio codec.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Board file support for Ventana is not yet mainlined, and probably won't
ever be given the move to Device-Tree. Consequently, the Ventana entry
is being removed from arch/arm/tools/mach-types in the next merge window,
since it was registered over a year ago.
This will also remove function machine_is_ventana(), which is used by
the ASoC Tegra WM8903 machine driver. This will cause compilation
failures. Drop Ventana support to resolve this.
Hopefully, in the not-too-distant future, tegra_wm8903.c will be able to
configure itself from Device-Tree, and hence we'll be able to re-instate
Ventana support just by creating a .dts file for the board.
Also note that Aebl support is in a similar boat. However, that board
isn't scheduled for deprecation for at least another 5 months, and
perhaps we will have completely removed non-Device-Tree support from
tegra_wm8903.c by then and/or adjusted mach-types policy.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Joseph Pentland <jp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move the test on pdev->id before the kzalloc to avoid requiring kfree when
the test fails. This fix was suggested by Wolfram Sang.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier x;
expression E1!=0,E2,E3,E4;
statement S;
iterator I;
@@
(
if (...) { ... when != kfree(x)
when != x = E3
when != E3 = x
* return ...;
}
... when != x = E2
when != I(...,x,...) S
if (...) { ... when != x = E4
kfree(x); ... return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Dong Aisheng <b29396@freescale.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Saif needs clear clk gate first before writing registers or the write
will not success.
The original xx_get_mclk function clear clk gate after mclk setting
that may cause the former mclk setting unwork, then the real output
mclk maybe inaccurate.
Placing the clear before setting mclk to avoid such an issue.
We also have to clear clk gate in startup instead of in prepare function.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
