Unlike EMR tools which encode type information in their tool ID, tools
for AES sensors are all "generic pens". It is inappropriate to make use
of the wacom_intuos_get_tool_type function when dealing with these kinds
of devices. Instead, we should only ever report BTN_TOOL_PEN or
BTN_TOOL_RUBBER, as depending on the state of the Eraser and Invert
bits.
Reported-by: Daniel Jutz <daniel@djutz.com>
Closes: https://lore.kernel.org/linux-input/3cd82004-c5b8-4f2a-9a3b-d88d855c65e4@heusel.eu/
Bisected-by: Christian Heusel <christian@heusel.eu>
Fixes: 9c2913b962 ("HID: wacom: more appropriate tool type categorization")
Link: https://gitlab.freedesktop.org/libinput/libinput/-/issues/1041
Link: https://github.com/linuxwacom/input-wacom/issues/440
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Cc: stable@vger.kernel.org
Acked-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Various Wacom fixes (Jason Gerecke):
- Support for high-resolution wheel scrolling
- Support touchrings with relative motion
- Support devices with two touchrings
- Support sequence numbers smaller than 16-bit
The driver currently assumes that the first sequence number it will see
is going to be 0. This is not a realiable assumption and can break if,
for example, the tablet has already been running for some time prior to
the kernel driver connecting to the device. This commit initializes the
expected sequence number to -1 and will only print the "Dropped" warning
the it has been updated to a non-negative value.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Tested-by: Joshua Dickens <joshua.dickens@wacom.com>
Fixes: 6d09085b38 ("HID: wacom: Adding Support for new usages")
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The current dropped packet reporting assumes that all sequence numbers
are 16 bits in length. This results in misleading "Dropped" messages if
the hardware uses fewer bits. For example, if a tablet uses only 8 bits
to store its sequence number, once it rolls over from 255 -> 0, the
driver will still be expecting a packet "256". This patch adjusts the
logic to reset the next expected packet to logical_minimum whenever
it overflows beyond logical_maximum.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Tested-by: Joshua Dickens <joshua.dickens@wacom.com>
Fixes: 6d09085b38 ("HID: wacom: Adding Support for new usages")
Signed-off-by: Jiri Kosina <jkosina@suse.com>
If a device has more than one touchring, we want to be sure that userspace
is able to distinguish them. Following previous standards, the first
absolute ring will be reported as ABS_WHEEL and the second as ABS_THROTTLE.
Relative rings will use REL_WHEEL_HI_RES / REL_WHEEL for the first and
REL_HWHEEL_HI_RES / REL_HWHEEL for the second.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Modern userspace (i.e. libinput) will make use of high-resolution
scrolling if supported. Hardware does not currently set a resolution
multiplier needed for effective high-res scrolling, but we can still
write code to support it in the future.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
If a touchring is configured to send relative events (e.g. +1 or -1 every
time some bit of rotational distance is covered), we should similarly
send relative events up to userspace. Previous non-HID tablets used
REL_WHEEL to send this kind of information, so we opt to use this same
axis since userspace (xf86-input-wacom and libinput) already expects
this kind of behavior from the Wacom kernel driver.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
When we encounter a usage mapped to ABS_X or ABS_Y which has a calculated
resolution of 0, we want to warn the user of this before setting a default
value. The previous language used the word "usage" but then printed out the
value of a "code" instead. We can improve this.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The Wacom driver maps the HID_DG_TWIST usage to ABS_Z (rather than ABS_RZ)
for historic reasons. When the code to support twist was introduced in
commit 50066a042d ("HID: wacom: generic: Add support for height, tilt,
and twist usages"), we were careful to write it in such a way that it had
HID calculate the resolution of the twist axis assuming ABS_RZ instead
(so that we would get correct angular behavior). This was broken with
the introduction of commit 08a46b4190 ("HID: wacom: Set a default
resolution for older tablets"), which moved the resolution calculation
to occur *before* the adjustment from ABS_Z to ABS_RZ occurred.
This commit moves the calculation of resolution after the point that
we are finished setting things up for its proper use.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Fixes: 08a46b4190 ("HID: wacom: Set a default resolution for older tablets")
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Recent eraser and pen tools are able to be distinguished
by looking at its least significant nibble.
This modification applies it to wacom_intuos_get_tool_type
function and reduces its code lines.
Signed-off-by: Tatsunosuke Tobita <tatsunosuke.tobita@wacom.com>
Signed-off-by: Tatsunosuke Tobita <tatsunosuke.wacom@gmail.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Link: https://patch.msgid.link/20240709055729.17158-2-tatsunosuke.wacom@gmail.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
The pen ID, 0x80842, was not the correct ID for wacom driver to
treat. The ID was corrected to 0x8842.
Also, 0x4200 was not the expected ID used on any Wacom device.
Therefore, 0x4200 was removed.
Signed-off-by: Tatsunosuke Tobita <tatsunosuke.tobita@wacom.com>
Signed-off-by: Tatsunosuke Tobita <tatsunosuke.wacom@gmail.com>
Fixes: bfdc750c4c ("HID: wacom: add three styli to wacom_intuos_get_tool_type")
Cc: stable@kernel.org #6.2
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Link: https://patch.msgid.link/20240709055729.17158-1-tatsunosuke.wacom@gmail.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Replace the indirect accesses to struct->wacom_wac from struct->wacom
to the direct access in order for better code reading.
Signed-off-by: Tatsunosuke Tobita <tatsunosuke.tobita@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The xf86-input-wacom driver does not treat '0' as a valid serial
number and will drop any input report which contains an
MSC_SERIAL = 0 event. The kernel driver already takes care to
avoid sending any MSC_SERIAL event if the value of serial[0] == 0
(which is the case for devices that don't actually report a
serial number), but this is not quite sufficient.
Only the lower 32 bits of the serial get reported to userspace,
so if this portion of the serial is zero then there can still
be problems.
This commit allows the driver to report either the lower 32 bits
if they are non-zero or the upper 32 bits otherwise.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Tatsunosuke Tobita <tatsunosuke.tobita@wacom.com>
Fixes: f85c9dc678 ("HID: wacom: generic: Support tool ID and additional tool types")
CC: stable@vger.kernel.org # v4.10
Signed-off-by: Jiri Kosina <jkosina@suse.com>
There appear to be a few different ways that Wacom devices can deal with
confidence:
1. If the device looses confidence in a touch, it will first clear
the tipswitch flag in one report, and then clear the confidence
flag in a second report. This behavior is used by e.g. DTH-2452.
2. If the device looses confidence in a touch, it will clear both
the tipswitch and confidence flags within the same report. This
behavior is used by some AES devices.
3. If the device looses confidence in a touch, it will clear *only*
the confidence bit. The tipswitch bit will remain set so long as
the touch is tracked. This behavior may be used in future devices.
The driver does not currently handle situation 3 properly. Touches that
loose confidence will remain "in prox" and essentially frozen in place
until the tipswitch bit is finally cleared. Not only does this result
in userspace seeing a stuck touch, but it also prevents pen arbitration
from working properly (the pen won't send events until all touches are
up, but we don't currently process events from non-confident touches).
This commit centralizes the checking of the confidence bit in the
wacom_wac_finger_slot() function and has 'prox' depend on it. In the
case where situation 3 is encountered, the treat the touch as though
it was removed, allowing both userspace and the pen arbitration to
act normally.
Signed-off-by: Tatsunosuke Tobita <tatsunosuke.tobita@wacom.com>
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Fixes: 7fb0413baa ("HID: wacom: Use "Confidence" flag to prevent reporting invalid contacts")
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Even if a user does not use their AES pen for an extended period,
the battery power supply attributes continue to exist.
This results in the desktop showing battery status for a pen
that is no longer in use and which may in fact be in a different
state (e.g. the user may be charging the pen).
To avoid confusion and ensure userspace has an accurate view
of the battery state, this patch automatically removes
the power_supply after 30 minutes of inactivity.
Signed-off-by: Tatsunosuke Tobita <tatsunosuke.tobita@wacom.com>
Reviewed-by: Jason Gerecke <Jason.Gerecke@wacom.com>
Reviewed-by: Aaron Skomra <aaron.skomra@wacom.com>
Reviewed-by: Josh Dickens <joshua.dickens@wacom.com>
Link: https://lore.kernel.org/r/20231114235729.6867-1-tatsunosuke.wacom@gmail.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Help differentiate the two remote related "serial" struct variables by
renaming "wacom_remote_data" to "wacom_remote_work_data".
Signed-off-by: Aaron Skomra <skomra@gmail.com>
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The 'connected' variable was poorly named, and this has led to some
confusion. We can get the same information by checking if a serial number
exists in the specified EKR slot.
Signed-off-by: Aaron Skomra <skomra@gmail.com>
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently the EKR battery remains even after we stop getting information
from the device. This can lead to a stale battery persisting indefinitely
in userspace.
The remote sends a heartbeat every 10 seconds. Delete the battery if we
miss two heartbeats (after 21 seconds). Restore the battery once we see
a heartbeat again.
Signed-off-by: Aaron Skomra <skomra@gmail.com>
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Fixes: 9f1015d45f ("HID: wacom: EKR: attach the power_supply on first connection")
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Code which interacts with timestamps needs to use the ktime_t type
returned by functions like ktime_get. The int type does not offer
enough space to store these values, and attempting to use it is a
recipe for problems. In this particular case, overflows would occur
when calculating/storing timestamps leading to incorrect values being
reported to userspace. In some cases these bad timestamps cause input
handling in userspace to appear hung.
Link: https://gitlab.freedesktop.org/libinput/libinput/-/issues/901
Fixes: 17d793f3ed ("HID: wacom: insert timestamp to packed Bluetooth (BT) events")
CC: stable@vger.kernel.org
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20230608213828.2108-1-jason.gerecke@wacom.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
If high bit is set to 1 in ((data[3] & 0x0f << 28), after all arithmetic
operations and integer promotions are done, high bits in
wacom->serial[idx] will be filled with 1s as well.
Avoid this, albeit unlikely, issue by specifying left operand's __u64
type for the right operand.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: 3bea733ab2 ("USB: wacom tablet driver reorganization")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some devices will include battery status usages in the HID descriptor
but we won't see that battery data for one reason or another. For example,
AES sensors won't send battery data unless an AES pen is in proximity.
If a user does not have an AES pen but instead only interacts with the
AES touchscreen with their fingers then there is no need for us to create
a battery object. Similarly, if a family of peripherals shares the same
HID descriptor between wired-only and wireless-capable SKUs, users of the
former may never see a battery event and will not want a power_supply
object created.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217062
Link: https://gitlab.gnome.org/GNOME/gnome-control-center/-/issues/2354
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Tested-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Rather than creating batteries as part of the initial device probe, let's
make the process lazy. This gives us the opportunity to prevent batteries
from being created in situations where they are unnecessary.
There are two cases in particular where batteries are being unnecessarily
created at initialization. These are AES sensors (for which we don't know
any battery status information until a battery-powered pen actually comes
into prox) peripheral tablets which share HID descriptors between the
wired-only and wireless-capable SKUs of a family of devices.
This patch will delay battery initialization of the former until a pen
actually comes into prox. It will delay battery initialization of the
latter until either a pen comes into prox or a "heartbeat" packet is
processed.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217062
Link: https://gitlab.gnome.org/GNOME/gnome-control-center/-/issues/2354
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Tested-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some older tablets may not report physical maximum for X/Y
coordinates. Set a default to prevent undefined resolution.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Link: https://lore.kernel.org/r/20230409164229.29777-1-ping.cheng@wacom.com
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
To fully utilize the BT polling/refresh rate, a few input events
are sent together to reduce event delay. This causes issue to the
timestamp generated by input_sync since all the events in the same
packet would pretty much have the same timestamp. This patch inserts
time interval to the events by averaging the total time used for
sending the packet.
This decision was mainly based on observing the actual time interval
between each BT polling. The interval doesn't seem to be constant,
due to the network and system environment. So, using solutions other
than averaging doesn't end up with valid timestamps.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some Wacom devices have a special "bootloader" mode that is used for
firmware flashing. When operating in this mode, the device cannot be
used for input, and the HID descriptor is not able to be processed by
the driver. The driver generates an "Unknown device_type" warning and
then returns an error code from wacom_probe(). This is a problem because
userspace still needs to be able to interact with the device via hidraw
to perform the firmware flash.
This commit adds a non-generic device definition for 056a:0094 which
is used when devices are in "bootloader" mode. It marks the devices
with a special BOOTLOADER type that is recognized by wacom_probe() and
wacom_raw_event(). When we see this type we ensure a hidraw device is
created and otherwise keep our hands off so that userspace is in full
control.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Tested-by: Tatsunosuke Tobita <tatsunosuke.tobita@wacom.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When support was added for devices using an explicit 3rd barrel switch,
the logic used by devices emulating this feature was broken. The 'if'
statement / block that was introduced only handles the case where the
button is pressed (i.e. 'barrelswitch' and 'barrelswitch2' are both set)
but not the case where it is released (i.e. one or both being cleared).
This results in a BTN_STYLUS3 "down" event being sent when the button
is pressed, but no "up" event ever being sent afterwards.
This patch restores the previously-used logic for determining button
states in the emulated case so that switches are reported correctly
again.
Link: https://github.com/linuxwacom/xf86-input-wacom/issues/292
Fixes: 6d09085b38 ("HID: wacom: Adding Support for new usages")
CC: stable@vger.kernel.org #v5.19+
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Tested-by: Joshua Dickens <joshua.dickens@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We forgot to add the 3D pen ID a year ago. There are two new pro pen
IDs to be added.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add the new PIDs to wacom_wac.c to support the new model in the Intuos Pro series.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Tested-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove a left-over from commit 2874c5fd28 ("treewide: Replace GPLv2
boilerplate/reference with SPDX - rule 152").
An empty comment block can be removed.
While at it remove, also remove what is supposed to be the path/filename of
the file.
This is really low value... and wrong since commit 471d17148c
("Input: wacom - move the USB (now hid) Wacom driver in drivers/hid")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Prox-out events may not be reliably sent by some AES firmware. This can
cause problems for users, particularly due to arbitration logic disabling
touch input while the pen is in prox.
This commit adds a timer which is reset every time a new prox event is
received. When the timer expires we check to see if the pen is still in
prox and force it out if necessary. This is patterend off of the same
solution used by 'hid-letsketch' driver which has a similar problem.
Link: https://github.com/linuxwacom/input-wacom/issues/310
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Touch switch state is received through WACOM_PAD_FIELD. However, it
is reported by touch_input. Don't register pad_input if no other pad
events require the interface.
Cc: stable@vger.kernel.org
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The generic routine, wacom_wac_pen_event, turns rotation value 90
degree anti-clockwise before posting the events. This non-zero
event trggers a non-zero ABS_Z event for non art pen tools. However,
HID_DG_TWIST is only supported by art pen.
[jkosina@suse.cz: fix build: add missing brace]
Cc: stable@vger.kernel.org
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
--
Hi Jiri,
This is kind of a version 2 of the last one I posted two days ago.
I updated the logic so it has less changed lines: 29 vs 158! Hopefully,
the logic is easier to follow now. Please ignore the last one.
Thank you!
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Kernel test robot throws the following warning -
>> drivers/hid/wacom_wac.c:2411:42: warning: format specifies type 'unsigned short' but the argument has type 'int' [-Wformat]
hid_warn(hdev, "Dropped %hu packets", value - wacom_wac->hid_data.sequence_number);
~~~ ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
%d
Explicitly casting the argument to unsigned short to silence the warning and retain the intended behavior.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Joshua Dickens <joshua.dickens@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added supprt for the following usages:
* HID_DG_SCANTIME to report the timestamp for pen and touch events.
* WACOM_HID_WD_BARRELSWITCH3 to support pens with 3 buttons.
* WACOM_HID_WD_SEQUENCENUMBER to detect and report dropped packets.
Signed-off-by: Joshua Dickens <joshua.dickens@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If we ever see a touch report with contact count data we initialize
several variables used to read the contact count in the pre-report
phase. These variables are never reset if we process a report which
doesn't contain a contact count, however. This can cause the pre-
report function to trigger a read of arbitrary memory (e.g. NULL
if we're lucky) and potentially crash the driver.
This commit restores resetting of the variables back to default
"none" values that were used prior to the commit mentioned
below.
Link: https://github.com/linuxwacom/input-wacom/issues/276
Fixes: 003f50ab67 (HID: wacom: Update last_slot_field during pre_report phase)
CC: stable@vger.kernel.org
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
AES hardware may internally re-classify a contact that it thought was
intentional as a palm. Intentional contacts are reported as "down" with
the confidence bit set. When this re-classification occurs, however, the
state transitions to "up" with the confidence bit cleared. This kind of
transition appears to be legal according to Microsoft docs, but we do
not handle it correctly. Because the confidence bit is clear, we don't
call `wacom_wac_finger_slot` and update userspace. This causes hung
touches that confuse userspace and interfere with pen arbitration.
This commit adds a special case to ignore the confidence flag if a contact
is reported as removed. This ensures we do not leave a hung touch if one
of these re-classification events occured. Ideally we'd have some way to
also let userspace know that the touch has been re-classified as a palm
and needs to be canceled, but that's not possible right now :)
Link: https://github.com/linuxwacom/input-wacom/issues/288
Fixes: 7fb0413baa (HID: wacom: Use "Confidence" flag to prevent reporting invalid contacts)
CC: stable@vger.kernel.org
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These two values go hand-in-hand and must be valid for the driver to
behave correctly. We are currently lazy about updating the values and
rely on the "expected" code flow to take care of making sure they're
valid at the point they're needed. The "expected" flow changed somewhat
with commit f8b6a74719 ("HID: wacom: generic: Support multiple tools
per report"), however. This led to problems with the DTH-2452 due (in
part) to *all* contacts being fully processed -- even those past the
expected contact count. Specifically, the received count gets reset to
0 once all expected fingers are processed, but not the expected count.
The rest of the contacts in the report are then *also* processed since
now the driver thinks we've only processed 0 of N expected contacts.
Later commits such as 7fb0413baa (HID: wacom: Use "Confidence" flag to
prevent reporting invalid contacts) worked around the DTH-2452 issue by
skipping the invalid contacts at the end of the report, but this is not
a complete fix. The confidence flag cannot be relied on when a contact
is removed (see the following patch), and dealing with that condition
re-introduces the DTH-2452 issue unless we also address this contact
count laziness. By resetting expected and received counts at the same
time we ensure the driver understands that there are 0 more contacts
expected in the report. Similarly, we also make sure to reset the
received count if for some reason we're out of sync in the pre-report
phase.
Link: https://github.com/linuxwacom/input-wacom/issues/288
Fixes: f8b6a74719 ("HID: wacom: generic: Support multiple tools per report")
CC: stable@vger.kernel.org
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The HID descriptor of many of Wacom's touch input devices include a
"Confidence" usage that signals if a particular touch collection contains
useful data. The driver does not look at this flag, however, which causes
even invalid contacts to be reported to userspace. A lucky combination of
kernel event filtering and device behavior (specifically: contact ID 0 ==
invalid, contact ID >0 == valid; and order all data so that all valid
contacts are reported before any invalid contacts) spare most devices from
any visibly-bad behavior.
The DTH-2452 is one example of an unlucky device that misbehaves. It uses
ID 0 for both the first valid contact and all invalid contacts. Because
we report both the valid and invalid contacts, the kernel reports that
contact 0 first goes down (valid) and then goes up (invalid) in every
report. This causes ~100 clicks per second simply by touching the screen.
This patch inroduces new `confidence` flag in our `hid_data` structure.
The value is initially set to `true` at the start of a report and can be
set to `false` if an invalid touch usage is seen.
Link: https://github.com/linuxwacom/input-wacom/issues/270
Fixes: f8b6a74719 ("HID: wacom: generic: Support multiple tools per report")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Tested-by: Joshua Dickens <joshua.dickens@wacom.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add the new PIDs to wacom_wac.c to support the new models in the Intuos series.
[jkosina@suse.cz: fix changelog]
Signed-off-by: Joshua Dickens <joshua.dickens@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We perform this same set of tests to see if touch input is muted in
several places. We might as well replace these independent copies with
an inline function.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Empty sync events clutter up logs and are a waste of CPU cycles. We can
avoid sending mt_sync events if touch is disabled or a specific slot is
unused. We can avoid sending full sync events if no events were generated.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Avoid doing unnecessary work when touch is disabled by detecting this
condition and returning early. Note that the probe process sends GET
FEATURE requests to discover e.g. HID_DG_CONTACTMAX, so we can't start
ignoring touch reports until probe finishes.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Wacom touch devices have two types of touch switches: softkey touch
toggle and hardware touch switch. For softkey toggle, we assume
touch is on by default in the driver. However the hardware touch
switch is controlled by end users. We don't know if it's on or off
before getting the status event.
This patch sets touch off for devices with a hardware switch until we
get the status. This is a bit safer for users who leave the switch "off"
and don't want any accidental touches. The tradeoff is a slight delay
between device connection and touch becoming enabled for users who
leave the switch "on".
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Tested-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The `input_mt_get_slot_by_key` function may return a negative value
if an error occurs (e.g. running out of slots). If this occurs we
should really avoid reporting any data for the slot.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 670e90924b ("HID: wacom: support named keys on older devices")
added support for sending named events from the soft buttons on the
24HDT and 27QHDT. In the process, however, it inadvertantly disabled the
touchscreen of the 24HDT and 27QHDT by default. The
`wacom_set_shared_values` function would normally enable touch by default
but because it checks the state of the non-shared `has_mute_touch_switch`
flag and `wacom_setup_touch_input_capabilities` sets the state of the
/shared/ version, touch ends up being disabled by default.
This patch sets the non-shared flag, letting `wacom_set_shared_values`
take care of copying the value over to the shared version and setting
the default touch state to "on".
Fixes: 670e90924b ("HID: wacom: support named keys on older devices")
CC: stable@vger.kernel.org # 5.4+
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Only set the bits that are supported by the targeted devices.
This patch also removes duplicated set_bit calls.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Jason Gerecke <Jason.Gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Valid HID_GENERIC type of devices set EV_KEY and EV_ABS by wacom_map_usage.
When *_input_capabilities are reached, those devices should already have
their proper EV_* set. EV_KEY and EV_ABS only need to be set for
non-HID_GENERIC type of devices in *_input_capabilities.
Devices that don't support HID descitoprs will pass back to hid-input for
registration without being accidentally rejected by the introduction of
patch: "Input: refuse to register absolute devices without absinfo"
Fixes: 6ecfe51b40 ("Input: refuse to register absolute devices without absinfo")
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Jason Gerecke <Jason.Gerecke@wacom.com>
Tested-by: Juan Garrido <Juan.Garrido@wacom.com>
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
