Makes it easier to keep in sync with ddx and the upstream
AMD versions.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Also remove the problematic enums that were unused
remnants from the ddx.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Somehow, strange characters made their way zaurus gpio .desc
fields. Fix it.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Stanislav Brabec <utx@penguin.cz>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
In the driver probe function the emac module clock needs to
be enabled before calling register_netdev(). As soon as the
device is registered the driver get_stats function can be invoked
by the core - the module clock must be switched on to be able to
read from stats registers. Also explicitly call matching clk_disable
for failure conditions in probe function.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Davicom DM9100 and DM9102 chips are used on the motherboards of
some SPARC systems (supported by the tulip driver) and also in PCI
expansion cards (supported by the dmfe driver). There is no
difference in the PCI device ids for the two different configurations,
so these drivers both claim the device ids. However, it is possible
to distinguish the two configurations by the presence of Open Firmware
properties for them, so we do that.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
tc is still throwing a warning that is could be used
uninitialized. This fixes it, and properly formats the device ID
checks for the use of this variable.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__per_cpu_idtrs is statically allocated ... on CONFIG_NR_CPUS=4096
systems it hogs 16MB of memory. This is way too much for a quite
probably unused facility (only KVM uses dynamic TR registers).
Change to an array of pointers, and allocate entries as needed on
a per cpu basis. Change the name too as the __per_cpu_ prefix is
confusing (this isn't a classic <linux/percpu.h> type object).
Signed-off-by: Tony Luck <tony.luck@intel.com>
linux-next-20081022//include/linux/kgdb.h:308): duplicate section name 'Description'
and fix typos in that file's kernel-doc comments.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
In blackfin, kgdb is running in delayed exception IRQ5 other than in
exception IRQ3 directly. Register reti other than retx in pt_regs is
the kgdb return address. So, don't put PC in gdb_regs into retx.
CC: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Sonic Zhang <sonic.adi@gmail.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Blackfin needs it own arch specific probe_kernel_read() and
probe_kernel_write().
This was moved out of the kgdb code and into the
arch/blackfin/maccess.c, because it is a generic kernel api.
The arch specific kgdb.c for blackfin was cleaned of all functions
which exist in the kgdb core that do the same thing after resolving
the probe_kernel_read() and probe_kernel_write(). This also
eliminated the need for most of the #include's.
CC: Sonic Zhang <sonic.adi@gmail.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Some archs such as blackfin, would like to have an arch specific
probe_kernel_read() and probe_kernel_write() implementation which can
fall back to the generic implementation if no special operations are
needed.
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
As noticed by Dan Carpenter <error27@gmail.com>, update_nl_seq()
currently contains an out of bounds read of the seq_aft_nl array
when looking for the oldest sequence number position.
Fix it to only compare valid positions.
Cc: stable@kernel.org
Signed-off-by: Patrick McHardy <kaber@trash.net>
Fix remaining xattr locks acquired in reiserfs_xattr_set_handle()
while we are holding the reiserfs lock to avoid lock inversions.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Christian Kujau <lists@nerdbynature.de>
Cc: Alexander Beregalov <a.beregalov@gmail.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Ingo Molnar <mingo@elte.hu>
Stanse found an unreachable statement in reiserfs_ioctl. There is a
if followed by error assignment and `break' with no braces. Add the
braces so that we don't break every time, but only in error case,
so that REISERFS_IOC_SETVERSION actually works when it returns no
error.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Reiserfs <reiserfs-devel@vger.kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
reiserfs_get_acl is usually not called under the reiserfs lock,
as it doesn't need it. But it happens when it is called by
reiserfs_acl_chmod(), which creates a dependency inversion against
the private xattr inodes mutexes for the given inode.
We need to call it without the reiserfs lock, especially since
it's unnecessary.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Christian Kujau <lists@nerdbynature.de>
Cc: Alexander Beregalov <a.beregalov@gmail.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Ingo Molnar <mingo@elte.hu>
For configurations where Synaptics hardware is present but the Synaptics
extensions support is not compiled in, the mouse is reprobed and a new
device is allocated on every suspend/resume.
During probe, psmouse_switch_protocol() calls psmouse_extensions() with
set_properties=1. This calls the dummy synaptics_init() which returns an
error code, instructing us not to use the synaptics extensions.
During resume, psmouse_reconnect() calls psmouse_extensions() with
set_properties=0, in which case call to synaptics_init() is bypassed and
PSMOUSE_SYNAPTICS is returned. Since the result is different from previous
attempt psmouse_reconnect() fails and full re-probe happens.
Fix this by tweaking the set_properties=0 codepath in psmouse_extensions()
to be more careful about offering PSMOUSE_SYNAPTICS extensions.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If NET_SKB_PAD is not a multiple of the cache line size, mv643xx_eth
allocates a couple of extra bytes at the start of each receive buffer
to make the data payload end up on a cache line boundary.
These extra bytes are skb_reserve()'d before DMA mapping, so they
should not be included in the DMA map byte count (as the mapping is
done starting at skb->data), nor should they be included in the
receive descriptor buffer size field, or the hardware can end up
DMAing beyond the end of the buffer, which can happen if someone
sends us a larger-than-MTU sized packet.
This problem was introduced in commit 7fd96ce47f ("mv643xx_eth:
rework receive skb cache alignment", May 6 2009), but hasn't appeared
to be problematic so far, probably as the main users of mv643xx_eth
all have NET_SKB_PAD == L1_CACHE_BYTES.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stanse found a memory leak in atl2_get_eeprom. eeprom_buff is not
freed/assigned on all paths. Fix that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>
Cc: Jie Yang <jie.yang@atheros.com>
Cc: atl1-devel@lists.sourceforge.net
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
A failure on request_irq() is always fatal but unlike other fatal
errors it's only reported to the user if net_debug is set. Make the
diagnostic unconditional and raise the priority so that errors are
more obvious to the user.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed missing newlines in calls to dev_warn & dev_err.
Signed-off-by: Jan Dumon <j.dumon@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't send flow control settings to any port other than the modem port.
Older firmware ignored this request but did sent a reply. Newer firmware just
ignores it without reply and causes a 5 second timeout every time a port
(except for the modem port) is opened or if tiocm settings are changed.
Signed-off-by: Jan Dumon <j.dumon@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attempt to reset the usb device when we receive usb bus errors.
Signed-off-by: Jan Dumon <j.dumon@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't change the state of a port if it's not open. This fixes an issue where a
port sometimes has to be opened twice before data can be received.
Signed-off-by: Jan Dumon <j.dumon@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some fields are always little endian and have to be converted on big endian
machines.
Signed-off-by: Jan Dumon <j.dumon@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Claw module cannot be loaded together with qeth, because "qeth" has
been errorneously used as root device name. It is changed into "claw".
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pcnet_cs,serial_cs:
add cis of KTI PE520 pcmcia network card,
and serial card(Sierra Wireless AC860).
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we have L3 tunnels with different inner/outer families
(i.e. IPV4/IPV6) which use a multicast address as the outer tunnel
destination address, multicast packets will be loopbacked back to the
sending socket even if IP*_MULTICAST_LOOP is set to disabled.
The mc_loop flag is present in the family specific part of the socket
(e.g. the IPv4 or IPv4 specific part). setsockopt sets the inner
family mc_loop flag. When the packet is pushed through the L3 tunnel
it will eventually be processed by the outer family which if different
will check the flag in a different part of the socket then it was set.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
current the Rx/Tx FIFO size settings cause problem
when four UEC ethernets work simultaneously.
eg: GETH1, UEM-J15, GETH2, UEC-J5 on 8569MDS board
$ ifconfig eth0 10.193.20.166
$ ifconfig eth1 10.193.20.167
$ ifconfig eth2 10.193.20.168
then
$ ifconfig eth3 10.193.20.169
The fourth ethernet will cause all of interface broken,
you cann't ping successfully any more.
The patch fix this issue for MPC8569 Rev1.0 and Rev2.0
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: rs600: use correct mask for SW interrupt
gpu/drm/radeon/radeon_irq.c: move a dereference below a NULL test
drm/radeon/radeon_device.c: move a dereference below a NULL test
drm/radeon/radeon_fence.c: move a dereference below the NULL test
drm/radeon/radeon_connectors.c: add a NULL test before dereference
drm/radeon/kms: fix memory leak
drm/kms: Fix &&/|| confusion in drm_fb_helper_connector_parse_command_line()
drm/edid: Fix CVT width/height decode
drm/edid: Skip empty CVT codepoints
drm: remove address mask param for drm_pci_alloc()
drm/radeon/kms: add missing breaks in i2c and ss lookups
drm/radeon/kms: add primary dac adj values table
drm/radeon/kms: fallback to default connector table
* korg/drm-radeon-next:
drm/radeon/kms: rs600: use correct mask for SW interrupt
gpu/drm/radeon/radeon_irq.c: move a dereference below a NULL test
drm/radeon/radeon_device.c: move a dereference below a NULL test
drm/radeon/radeon_fence.c: move a dereference below the NULL test
drm/radeon/radeon_connectors.c: add a NULL test before dereference
drm/radeon/kms: fix memory leak
drm/radeon/kms: add missing breaks in i2c and ss lookups
drm/radeon/kms: add primary dac adj values table
drm/radeon/kms: fallback to default connector table
The mask happens to be the same, but the IH is reading the status, not the
not the control register.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If a NULL value is possible, the dereference should only occur after the
NULL test.
Coverity CID: 13338
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If a NULL value is possible, the dereference should only occur after the
NULL test.
Coverity CID: 13335
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If a NULL value is possible, the dereference should only occur after the
NULL test.
Coverity CID: 13334
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The encoder variable can be NULL in this function so I believe it should
be checked before dereference.
Coverity CID: 13253
[airlied: extremely unlikely to happen]
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Stanse found a memory leak in radeon_master_create. master_priv is not
freed/assigned on all paths. Fix that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm_pci_alloc() has input of address mask for setting pci dma
mask on the device, which should be properly setup by drm driver.
And leave it as a param for drm_pci_alloc() would cause confusion
or mistake would corrupt the correct dma mask setting, as seen on
intel hw which set wrong dma mask for hw status page. So remove
it from drm_pci_alloc() function.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There is a possibility of a loop happening in the PLL output clock
chain on the S3C64XX series. clk_mpll's parent was set to be
clk_mout_mpll, but this is fed from clk_fout_epll (which is also
clk_mpll).
clk_mpll is meant to be the output from the MPLL, and clk_mout_mpll
is a seperate clock derived from the mux of clk_mpll and clk_fin_mpll
and thus should be considered a seperate clock.
Anything using clk_mpll directly really should not be relying on this
being the clock that is eventually routed to a peripheral, so remove the
loop and ensure that the clocks accurately represent the clock chain
in the device.
The clk_mpll is not being used outside of the s3c6400-clock.c code, so
this change should not break anything else.
Do the same for the EPLL.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel: (23 commits)
drm/i915: remove full registers dump debug
drm/i915: Add DP dpll limit on ironlake and use existing DPLL search function
drm/i915: Select the correct BPC for LVDS on Ironlake
drm/i915: Make the BPC in FDI rx/transcoder be consistent with that in pipeconf on Ironlake
drm/i915: Enable/disable the dithering for LVDS based on VBT setting
drm/i915: Permit pinning whilst the device is 'suspended'
drm/i915: Hold struct mutex whilst pinning power context bo.
drm/i915: fix unused var
drm/i915: Storage class should be before const qualifier
drm/i915: remove render reclock support
drm/i915: Fix RC6 suspend/resume
drm/i915: execbuf2 support
drm/i915: Reload hangcheck timer too for Ironlake
drm/i915: only enable hotplug for detected outputs
drm/i915: Track whether cursor needs physical address in intel_device_info
drm/i915: Implement IS_* macros using static tables
drm/i915: Move PCI IDs into i915 driver
drm/i915: Update LVDS connector status when receiving ACPI LID event
drm/i915: Add MALATA PC-81005 to ACPI LID quirk list
drm/i915: implement new pm ops for i915
...
The MMU code uses the copy_*_user_page() variants in access_process_vm()
rather than copy_*_user() as the former includes an icache flush. This
is important when doing things like setting software breakpoints with
gdb. So switch the NOMMU code over to do the same.
This patch makes the reasonable assumption that copy_from_user_page()
won't fail - which is probably fine, as we've checked the VMA from which
we're copying is usable, and the copy is not allowed to cross VMAs. The
one case where it might go wrong is if the VMA is a device rather than
RAM, and that device returns an error which - in which case rubbish will
be returned rather than EIO.
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: David McCullough <david_mccullough@mcafee.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When working with FDPIC, there are many shared mappings of read-only
code regions between applications (the C library, applet packages like
busybox, etc.), but the current do_mmap_pgoff() function will issue an
icache flush whenever a VMA is added to an MM instead of only doing it
when the map is initially created.
The flush can instead be done when a region is first mmapped PROT_EXEC.
Note that we may not rely on the first mapping of a region being
executable - it's possible for it to be PROT_READ only, so we have to
remember whether we've flushed the region or not, and then flush the
entire region when a bit of it is made executable.
However, this also affects the brk area. That will no longer be
executable. We can mprotect() it to PROT_EXEC on MPU-mode kernels, but
for NOMMU mode kernels, when it increases the brk allocation, making
sys_brk() flush the extra from the icache should suffice. The brk area
probably isn't used by NOMMU programs since the brk area can only use up
the leavings from the stack allocation, where the stack allocation is
larger than requested.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current code will load the stack size and protection markings, but
then only use the markings in the MMU code path. The NOMMU code path
always passes PROT_EXEC to the mmap() call. While this doesn't matter
to most people whilst the code is running, it will cause a pointless
icache flush when starting every FDPIC application. Typically this
icache flush will be of a region on the order of 128KB in size, or may
be the entire icache, depending on the facilities available on the CPU.
In the case where the arch default behaviour seems to be desired
(EXSTACK_DEFAULT), we probe VM_STACK_FLAGS for VM_EXEC to determine
whether we should be setting PROT_EXEC or not.
For arches that support an MPU (Memory Protection Unit - an MMU without
the virtual mapping capability), setting PROT_EXEC or not will make an
important difference.
It should be noted that this change also affects the executability of
the brk region, since ELF-FDPIC has that share with the stack. However,
this is probably irrelevant as NOMMU programs aren't likely to use the
brk region, preferring instead allocation via mmap().
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-2.6.33' of git://linux-nfs.org/~bfields/linux:
sunrpc: fix peername failed on closed listener
nfsd: make sure data is on disk before calling ->fsync
nfsd: fix "insecure" export option
