Change the 'rval' variable from QLA_FUNCTION_TIMEOUT into QLA_SUCCESS
before starting a loop that is only executed if rval is initialized
to QLA_SUCCESS. Coverity reported that loop as "dead code".
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The driver uses ha->mbx_cmd_flags variable to pass information between
its ISR and mailbox routines, however, it does so without the protection of
any locks. Under certain conditions, this can lead to multiple mailbox
command completions being signaled, which, in turn, leads to a false
mailbox timeout error for the subsequently issued mailbox command.
The issue occurs frequently but intermittenly with the Qlogic 8GFC mezz
card during card initialization, resulting in card initialization failure.
Signed-off-by: Gurinder (Sunny) Shergill <gurinder.shergill@hp.com>
Acked-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Wait for the IDC complete AEN before returning the loopback operation back to
the application to make sure the port is put back into normal operations.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently,the driver is processes RSCNs for each new NPIV ports that is created.
Processing the RSCN includes a name server query to see what has changed at the
name server side. The name server query is performed by the physical port and
each virtual port on the physical adapter (since the RSCN is passed to each
virtual port for processing). As the number of virtual ports being created
increases, this causes a lot of traffic and busies the firmware.
Processing the RSCN for a virtual port we already have a priori knowledge of is
not necessary so check the 24-bit fabric ID of the RSCN entry and skip
processing it if the RSCN is for a virtual port we already know about.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add the following error handling for loopback diagnostic mode with ISP83xx:
1. If we do not receive an MBA_DCBX_COMPLETE after our initial set port
configuration command, try to reset the port back into normal operation.
If that fails, take a FCoE dump and then reset the chip.
2. After completing the loopback diagnostic operation, if the reset of the port
back into normal operation fails then reset the port so we take a FCoE dump
and then reset the chip.
3. When we receive an IDC notification and the requested operation is loopback
extend the loop down timer so the link does not appear to down for an
extended period of time.
[jejb: fix checkpatch issue]
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Base the number of outstanding requests the driver will keep track of on the
available resources instead of being hard-coded.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Parameterize qla2x00_get_link_speed_str() to be generic on link speed.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Update the driver copyright from 2003-2011 to 2003-2012.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Minor changes to support loopback functionality with ISP83xx CNAs.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add LLD target mode for >= 24xx series HW. This code was originally based on
external qla2x00t module based on 8.02.01-k4, and has been refactored to
push the bulk of code into mainline qla2xxx.ko LLD -> qla_target.c.
The implementation uses internal workqueues for I/O context submission
into tcm_qla2xxx code, and includes the struct qla_tgt_func_tmpl API for
external interaction to allow qla2xxx LDD to function without direct
target-core dependencies:
It also enables qla_target.c usage within existing qla2xxx LLD code.
This includes:
*) Addition of target mode specific members to existing data
structures in qla_def.h and struct qla_hw_data->tgt_ops using
qla_target.h:struct qla_tgt_func_tmpl
*) Addition of struct qla_tgt_func_tmpl and direct calls into
qla_target.c logic w/ qlt_* prefixed functions.
*) Addition of qla_iocb.c:qla2x00_req_pkt() for ring processing, and
qla2x00_issue_marker() for handling request/response queue processing
for target mode operation
*) Addition of various qla_tgt_mode_enabled() logic checks in
qla24xx_nvram_config(), qla2x00_initialize_adapter(), qla2x00_rff_id(),
qla2x00_abort_isp(), qla24xx_modify_vp_config(), and
qla2x00_vp_abort_isp().
By default the new qlini_mode module parameter is setting initiator-mode
to 'enabled' in order for 'modprobe qla2xxx' to continue to function as
expected in initiator only mode. Enabling target-mode operation will
currently require a:
modprobe qla2xxx qlini_mode="disabled"
in order to explictly disabled initiator mode and allow target-mode
to be enabled via tcm_qla2xxx configfs fabric callers.
(nab: Convert to qlini_mode='enabled' by default in qla_target.c)
(joern: Remove loop_id from qla_tgt_make_local_sess() arguments +
Remove unused s_id + fix s_id endianness bug +
simplify qla_tgt_abort_work)
(gerard: fix section __exit mismatch in qla_tgt_exit)
(arun: Capture ATIO queue during firmware dump + Send SCR in target mode +
Target mode review comments)
(roland: Don't create duplicate target sessions to address tearing down
ACLs with IO in flight + Add missing call to qlt_fc_port_deleted
call during qla2x00_schedule_rport_del timeout)
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If interrupt registration failed we could crash the machine as we were trying
to deference some pointers which weren't allocated yet. Move the allocation
a little earlier and make some checks to the free resource code to make sure
that we don't try to free a resource that was never allocated.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In case of firmmware detected under-run condition and scsi status of
task_set_full or busy_condition, return that to the mid layer for proper error
handling instead of DID_ERROR (which causes error handler activation and a
full retry).
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Instead of processing each RSCN individually, use only the name server results
from the switch to tell the existance of a given fcport.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The driver is logging a slew of 'good' status requests for ELS/CT passthrough
commands. Change some log messages from:
* ql_log() -> ql_dbg()
* ql_log_info -> ql_dbg_user
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Rework the structures related to SRB processing to minimize the memory
allocations per I/O and manage resources associated with and completions
from common routines.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This can cause instability in mailbox command state machine handling.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When reading the incoming mailbox registers, read only the specified ones.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[jejb: fixed up checkpatch and casting errors]
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch contains minor fixes to our new logging infrastructure:
- Remove extranous messages.
- Re-add 'nexus' and 'hdl' information.
- Adjusted the message ids to fill up the holes.
- Display FCP_CMND priority on update.
- Log only mail box error conditions.
- Do not print "Firmware ready **** FAILED ****" if cable is unplugged.
- Drop noisy 'fw_state...curr time...' message.
- Correct nexus display during abort.
- Add a special case error-logging set to '1'.
- Catagorize I/O exception display handling.
- Correct the bsg msg code printing.
- Dont use dynamic logging after host is removed.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During heavy I/O (CPU-affinity mode enabled) and CLI/Agent
interactions, the driver would report periodic mailbox command
timeout statuses. Within the CPU-affinity ISR handler, the
driver should check the 'disable-msix-handshake' flag in deciding
whether or not to clear HCCRX_CLR_RISC_INT. The mode is not
specific to a dedicated queue, instead, applies to the current
'ha' context.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
sector_t can be different types, so cast it to its largest possible
type.
drivers/scsi/qla2xxx/qla_isr.c:1509:5: warning: format '%lx' expects type 'long unsigned int', but argument 5 has type 'sector_t'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
