Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Reviewed-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux would not connect to other router running old version Cisco IOS (12.0).
This is most likely a bug in that version of IOS, since it is fixed
in later versions. As a workaround this patch allows a module parameter
to be set to disable compressing the protocol ID.
See: https://bugzilla.vyatta.com/show_bug.cgi?id=3979
RFC 1990 allows an implementation to formulate MP fragments as if protocol
compression had been negotiated. This allows us to always send compressed
protocol IDs. But some implementations don't accept MP fragments with
compressed protocol IDs. This parameter allows us to interoperate with
them. The default value of the configurable parameter is the same as the
current behavior: protocol compression is enabled. If protocol compression
is disabled we will not send compressed protocol IDs.
This is based on an earlier patch by Bob Gilligan (using a sysctl).
Module parameter is writable to allow for enabling even if ppp
is already loaded for other uses.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocating unit from ird might return several error codes
not only -EAGAIN, so it should not be changed and returned
precisely. Same time unit release procedure should be invoked
only if device is unregistering.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
CC: Paul Mackerras <paulus@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove pc variable to avoid arithmetic to compute fentry at each filter
instruction. Jumps directly manipulate fentry pointer.
As the last instruction of filter[] is guaranteed to be a RETURN, and
all jumps are before the last instruction, we dont need to check filter
bounds (number of instructions in filter array) at each iteration, so we
remove it from sk_run_filter() params.
On x86_32 remove f_k var introduced in commit 57fe93b374
(filter: make sure filters dont read uninitialized memory)
Note : We could use a CONFIG_ARCH_HAS_{FEW|MANY}_REGISTERS in order to
avoid too many ifdefs in this code.
This helps compiler to use cpu registers to hold fentry and A
accumulator.
On x86_32, this saves 401 bytes, and more important, sk_run_filter()
runs much faster because less register pressure (One less conditional
branch per BPF instruction)
# size net/core/filter.o net/core/filter_pre.o
text data bss dec hex filename
2948 0 0 2948 b84 net/core/filter.o
3349 0 0 3349 d15 net/core/filter_pre.o
on x86_64 :
# size net/core/filter.o net/core/filter_pre.o
text data bss dec hex filename
5173 0 0 5173 1435 net/core/filter.o
5224 0 0 5224 1468 net/core/filter_pre.o
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1699 commits)
bnx2/bnx2x: Unsupported Ethtool operations should return -EINVAL.
vlan: Calling vlan_hwaccel_do_receive() is always valid.
tproxy: use the interface primary IP address as a default value for --on-ip
tproxy: added IPv6 support to the socket match
cxgb3: function namespace cleanup
tproxy: added IPv6 support to the TPROXY target
tproxy: added IPv6 socket lookup function to nf_tproxy_core
be2net: Changes to use only priority codes allowed by f/w
tproxy: allow non-local binds of IPv6 sockets if IP_TRANSPARENT is enabled
tproxy: added tproxy sockopt interface in the IPV6 layer
tproxy: added udp6_lib_lookup function
tproxy: added const specifiers to udp lookup functions
tproxy: split off ipv6 defragmentation to a separate module
l2tp: small cleanup
nf_nat: restrict ICMP translation for embedded header
can: mcp251x: fix generation of error frames
can: mcp251x: fix endless loop in interrupt handler if CANINTF_MERRF is set
can-raw: add msg_flags to distinguish local traffic
9p: client code cleanup
rds: make local functions/variables static
...
Fix up conflicts in net/core/dev.c, drivers/net/pcmcia/smc91c92_cs.c and
drivers/net/wireless/ath/ath9k/debug.c as per David
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
Do this instead of subverting fields in skb proper.
The macros that could very easily match variable or function
names were also just asking for trouble.
Signed-off-by: David S. Miller <davem@davemloft.net>
Smatch complains because we check whether "pch->chan" is NULL and then
dereference it unconditionally on the next line. Partly the reason this
bug was introduced is because code was too complicated. I've simplified
it a little.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All these files use the big kernel lock in a trivial
way to serialize their private file operations,
typically resulting from an earlier semi-automatic
pushdown from VFS.
None of these drivers appears to want to lock against
other code, and they all use the BKL as the top-level
lock in their file operations, meaning that there
is no lock-order inversion problem.
Consequently, we can remove the BKL completely,
replacing it with a per-file mutex in every case.
Using a scripted approach means we can avoid
typos.
file=$1
name=$2
if grep -q lock_kernel ${file} ; then
if grep -q 'include.*linux.mutex.h' ${file} ; then
sed -i '/include.*<linux\/smp_lock.h>/d' ${file}
else
sed -i 's/include.*<linux\/smp_lock.h>.*$/include <linux\/mutex.h>/g' ${file}
fi
sed -i ${file} \
-e "/^#include.*linux.mutex.h/,$ {
1,/^\(static\|int\|long\)/ {
/^\(static\|int\|long\)/istatic DEFINE_MUTEX(${name}_mutex);
} }" \
-e "s/\(un\)*lock_kernel\>[ ]*()/mutex_\1lock(\&${name}_mutex)/g" \
-e '/[ ]*cycle_kernel_lock();/d'
else
sed -i -e '/include.*\<smp_lock.h\>/d' ${file} \
-e '/cycle_kernel_lock()/d'
fi
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix bug in multilink fragment size calculation introduced by
commit 9c705260fe
"ppp: ppp_mp_explode() redesign"
Signed-off-by: Ben McKeegan <ben@netservers.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse complains about shadowed declaration of skb. So use other
name.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use memdup_user when user data is immediately copied into the
allocated region.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
position p;
identifier l1,l2;
@@
- to = \(kmalloc@p\|kzalloc@p\)(size,flag);
+ to = memdup_user(from,size);
if (
- to==NULL
+ IS_ERR(to)
|| ...) {
<+... when != goto l1;
- -ENOMEM
+ PTR_ERR(to)
...+>
}
- if (copy_from_user(to, from, size) != 0) {
- <+... when != goto l2;
- -EFAULT
- ...+>
- }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
- This patch removes MIN_FRAG_SIZE definition in
drivers/net/ppp_generic.c as it is unneeded.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds:
alias: devname:<name>
to some common kernel modules, which will allow the on-demand loading
of the kernel module when the device node is accessed.
Ideally all these modules would be compiled-in, but distros seems too
much in love with their modularization that we need to cover the common
cases with this new facility. It will allow us to remove a bunch of pretty
useless init scripts and modprobes from init scripts.
The static device node aliases will be carried in the module itself. The
program depmod will extract this information to a file in the module directory:
$ cat /lib/modules/2.6.34-00650-g537b60d-dirty/modules.devname
# Device nodes to trigger on-demand module loading.
microcode cpu/microcode c10:184
fuse fuse c10:229
ppp_generic ppp c108:0
tun net/tun c10:200
dm_mod mapper/control c10:235
Udev will pick up the depmod created file on startup and create all the
static device nodes which the kernel modules specify, so that these modules
get automatically loaded when the device node is accessed:
$ /sbin/udevd --debug
...
static_dev_create_from_modules: mknod '/dev/cpu/microcode' c10:184
static_dev_create_from_modules: mknod '/dev/fuse' c10:229
static_dev_create_from_modules: mknod '/dev/ppp' c108:0
static_dev_create_from_modules: mknod '/dev/net/tun' c10:200
static_dev_create_from_modules: mknod '/dev/mapper/control' c10:235
udev_rules_apply_static_dev_perms: chmod '/dev/net/tun' 0666
udev_rules_apply_static_dev_perms: chmod '/dev/fuse' 0666
A few device nodes are switched to statically allocated numbers, to allow
the static nodes to work. This might also useful for systems which still run
a plain static /dev, which is completely unsafe to use with any dynamic minor
numbers.
Note:
The devname aliases must be limited to the *common* and *single*instance*
device nodes, like the misc devices, and never be used for conceptually limited
systems like the loop devices, which should rather get fixed properly and get a
control node for losetup to talk to, instead of creating a random number of
device nodes in advance, regardless if they are ever used.
This facility is to hide the mess distros are creating with too modualized
kernels, and just to hide that these modules are not compiled-in, and not to
paper-over broken concepts. Thanks! :)
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: Tigran Aivazian <tigran@aivazian.fsnet.co.uk>
Cc: Ian Kent <raven@themaw.net>
Signed-Off-By: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Frequently when using PPPoE with an interface MTU greater than 1500,
the skb is likely to be non-linear. If the skb needs to be passed to
pppd then the skb data must be read correctly.
The previous commit fixes an issue with accidentally sending skbs
to pppd based on an invalid read of the protocol type. When that
error occurred pppd was reading invalid skb data too.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ppp_input(), PPP_PROTO(skb) may refer to invalid data in the skb.
If this happens and (proto >= 0xc000 || proto == PPP_CCPFRAG) then
the packet is passed directly to pppd.
This occurs frequently when using PPPoE with an interface MTU
greater than 1500 because the skb is more likely to be non-linear.
The next 2 bytes need to be pulled in ppp_input(). The pull of 2
bytes in ppp_receive_frame() has been removed as it is no longer
required.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
ppp_dev_name() gives PPP users visibility of a ppp channel's device
name. This can be used by L2TP drivers to dump the assigned PPP
interface name.
Signed-off-by: James Chapman <jchapman@katalix.com>
Reviewed-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
I was just looking at ppp_generic, and noticed that it fairly recently
(as in the last year) got rather mangled with many spaces turned into tabs
in places they very much shouldn't have been. I tracked it down to commit
9c705260fe (ppp: ppp_mp_explode() redesign).
I am amazed if that patch passed the patch checking script. I have no
idea what kind of weird editor setting did this, but it has to have been a
weird editor setting or a very unfortunate search and replace gone wrong.
I only found it trying to apply a patch I was playing with and wondering
why it wouldn't apply. Then I found there were tabs in the middle of
comments that used to be spaces.
Well here is a patch that should fix it up as far as I can tell.
Purely whitespace repair. No actual code changes.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only files where David Miller is the primary git-signer.
wireless, wimax, ixgbe, etc are not modified.
Compile tested x86 allyesconfig only
Not all files compiled (not x86 compatible)
Added a few > 80 column lines, which I ignored.
Existing checkpatch complaints ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take advantage of the new pernet automatic storage management,
and stop using compatibility network namespace functions.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPP does not correctly call pskb_may_pull() on all necessary receive paths
before reading the PPP protocol, thus causing PPP to report seemingly
random 'unsupported protocols' and eventually trigger BUG_ON(skb->len <
skb->data_len) in skb_pull_rcsum() when receiving multilink protocol in
non-linear skbs.
ppp_receive_nonmp_frame() does not call pskb_may_pull() before reading the
protocol number. For the non-mp receive path this is not a problem, as
this check is done in ppp_receive_frame(). For the mp receive path,
ppp_mp_reconstruct() usually copies the data into a new linear skb.
However, in the case where the frame is made up of a single mp fragment,
the mp header is pulled and the existing skb used. This skb was then
passed to ppp_receive_nonmp_frame() without checking if the encapsulated
protocol header could safely be read.
Signed-off-by: Ben McKeegan <ben@netservers.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are all drivers that don't touch real hardware.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's too stupid to see that we always set flen to something
before we use it in ppp_mp_explode():
drivers/net/ppp_generic.c: In function 'ppp_push':
drivers/net/ppp_generic.c:1314: warning: 'flen' may be used uninitialized in this function
drivers/net/ppp_generic.c:1314: note: 'flen' was declared here
This started warning after commit a53a8b5682
("ppp: fix lost fragments in ppp_mp_explode() (resubmit)")
So just put an explicit unconditional initialization there to
hush it up.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the corner cases where the sum of MTU of the free
channels (adjusted for fragmentation overheads) is less than the MTU
of PPP link. There are at least 3 situations where this case might
arise:
- some of the channels are busy
- the multilink session is running in a degraded state (i.e. with less
than its full complement of active channels)
- by design, where multilink protocol is being used to artificially
increase the effective link MTU of a single link.
Without this patch, at most 1 fragment is ever sent per free channel
for a given PPP frame and any remaining part of the PPP frame that
does not fit into those fragments is silently discarded.
This patch restores the original behaviour which was broken by commit
9c705260fe 'ppp:ppp_mp_explode()
redesign'. Once all 'free' channels have been given a fragment, an
additional fragment is queued to each available channel in turn, as many
times as necessary, until the entire PPP frame has been consumed.
Signed-off-by: Ben McKeegan <ben@netservers.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is the result of an automatic spatch transformation to convert
all ndo_start_xmit() return values of 0 to NETDEV_TX_OK.
Some occurences are missed by the automatic conversion, those will be
handled in a seperate patch.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek pointed pppoe can call back dev_queue_xmit(), and might need
skb->dst, so its safer to unset IFF_XMIT_DST_RELEASE on ppp devices.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I found the PPP subsystem to not work properly when connecting channels
with different speeds to the same bundle.
Problem Description:
As the "ppp_mp_explode" function fragments the sk_buff buffer evenly
among the PPP channels that are connected to a certain PPP unit to
make up a bundle, if we are transmitting using an upper layer protocol
that requires an Ack before sending the next packet (like TCP/IP for
example), we will have a bandwidth bottleneck on the slowest channel
of the bundle.
Let's clarify by an example. Let's consider a scenario where we have
two PPP links making up a bundle: a slow link (10KB/sec) and a fast
link (1000KB/sec) working at the best (full bandwidth). On the top we
have a TCP/IP stack sending a 1000 Bytes sk_buff buffer down to the
PPP subsystem. The "ppp_mp_explode" function will divide the buffer in
two fragments of 500B each (we are neglecting all the headers, crc,
flags etc?.). Before the TCP/IP stack sends out the next buffer, it
will have to wait for the ACK response from the remote peer, so it
will have to wait for both fragments to have been sent over the two
PPP links, received by the remote peer and reconstructed. The
resulting behaviour is that, rather than having a bundle working
@1010KB/sec (the sum of the channels bandwidths), we'll have a bundle
working @20KB/sec (the double of the slowest channels bandwidth).
Problem Solution:
The problem has been solved by redesigning the "ppp_mp_explode"
function in such a way to make it split the sk_buff buffer according
to the speeds of the underlying PPP channels (the speeds of the serial
interfaces respectively attached to the PPP channels). Referring to
the above example, the redesigned "ppp_mp_explode" function will now
divide the 1000 Bytes buffer into two fragments whose sizes are set
according to the speeds of the channels where they are going to be
sent on (e.g . 10 Byets on 10KB/sec channel and 990 Bytes on
1000KB/sec channel). The reworked function grants the same
performances of the original one in optimal working conditions (i.e. a
bundle made up of PPP links all working at the same speed), while
greatly improving performances on the bundles made up of channels
working at different speeds.
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some pointless conditionals before kfree_skb().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this sparse warnings:
drivers/net/ppp_generic.c:919:43: warning: incorrect type in argument 1 (different signedness)
drivers/net/pppoe.c:1195:43: warning: incorrect type in argument 1 (different signedness)
drivers/net/pppol2tp.c:2666:43: warning: incorrect type in argument 1 (different signedness)
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPP is modular code so no initdata on netns hooks.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Each namespace contains ppp channels and units separately
with appropriate locks
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commits:
7a95d267fb
("net: ppp_generic - use idr technique instead of cardmaps")
ab5024ab23
("net: ppp_generic - use DEFINE_IDR for static initialization")
introduced usage of IDR functionality but broke userspace side.
Before this commits it was possible to allocate new ppp interface with
specified number. Now it fails with EINVAL. Fix it by trying to
allocate interface with specified unit number and return EEXIST if
fail which allow pppd to ask us to allocate new unit number.
And fix messages on memory allocation fails - add details that it's
PPP module who is complaining.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We could use DEFINE_IDR for statically allocated idr
that allow us to save a few lines of code.
And spell fix.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a segfault in ppp_shutdown_interface() and
ppp_destroy_interface() when a PPP connection is closed. I bisected
the problem to the following commit:
commit c8019bf3af
Author: Wang Chen <wangchen@cn.fujitsu.com>
Date: Thu Nov 20 04:24:17 2008 -0800
netdevice ppp: Convert directly reference of netdev->priv
1. Use netdev_priv(dev) to replace dev->priv.
2. Alloc netdev's private data by alloc_netdev().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original ppp_generic code treated the netdev and struct ppp as
independent data structures which were freed separately. In moving the
ppp struct into the netdev, it is now possible for the private data to
be freed before the call to ppp_shutdown_interface(), which is bad.
The kfree(ppp) in ppp_destroy_interface() is also wrong; presumably
ppp hasn't worked since the above commit.
The following patch fixes both problems.
Signed-off-by: James Chapman <jchapman@katalix.com>
Reviewed-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use idr technique instead of own implemented cardmaps.
It saves us a number of lines and gives an ability
to use library functions.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves neigh_setup and hard_start_xmit into the network device ops
structure. For bisection, fix all the previously converted drivers as well.
Bonding driver took the biggest hit on this.
Added a prefetch of the hard_start_xmit in the fast path to try and reduce
any impact this would have.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Use netdev_priv(dev) to replace dev->priv.
2. Alloc netdev's private data by alloc_netdev().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert this driver to network device ops. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Drivers need not do it any more.
Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: David S. Miller <davem@davemloft.net>
