1
Commit Graph

31 Commits

Author SHA1 Message Date
Atsushi Nemoto
c430452954 MIPS: Make local arrays with CL_SIZE static __initdata
Since commit 22242681cf ("MIPS: Extend
COMMAND_LINE_SIZE"), CL_SIZE is 4096 and local array variables with this
size will cause an build failure with default CONFIG_FRAME_WARN settings.

Although current users of such array variables are all early bootstrap
code and not likely to cause real stack overflow (thread_info corruption),
it is preferable to  to declare these arrays static with __initdata.

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-11-13 18:10:37 +01:00
Florian Fainelli
d36773e53f MIPS: RB532: Check irq number when handling GPIO interrupts
This patch makes sure that we are not going to clear
or change the interrupt status of a GPIO interrupt
superior to 13 as this is the maximum number of GPIO
interrupt source (p.232 of the RC32434 reference manual).

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-06-17 11:06:27 +01:00
Phil Sutter
d9bdffd210 Input: add driver for S1 button of rb532
Mikrotik's Routerboard 532 has two builtin buttons, from which one
triggers a hardware reset. The other one is accessible through GPIO
pin 1. Sadly, this pin is being multiplexed with UART0 input, so
enabling it as interrupt source (as implied by the gpio-keys driver)
is not possible unless UART0 has been turned off. The later one though
is a rather bad idea as the Routerboard is an embedded device with
only a single serial port, so it's almost always used as serial
console device.

This patch adds a driver based on INPUT_POLLDEV, which disables the
UART and reconfigures GPIO pin 1 temporarily while reading the button
state.  This procedure works fine and has been tested as part of
another, unpublished driver for this device.

Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-03-09 20:10:12 -07:00
Phil Sutter
0fc6bc0d6e MIPS: RB532: Export rb532_gpio_set_func()
This kernel symbol provides a way for drivers to switch on alternate
function for a certain GPIO pin. Turning it off is done implicitly when
changing the GPIO direction, as that would be fixed when using the given
pin als alternate function.

Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-01-30 21:33:01 +00:00
Phil Sutter
1c4db8e828 MIPS: RB532: Simplify dev3 init
As rb532_dev3_ctl_res is not used by any platform device, it can be dropped
when not used for holding the physical address of the device 3 controller.

Also a size of one byte should suffice when ioremapping the physical
address mentioned above, as only a single byte is being read from and
written to it.

Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-01-30 21:33:01 +00:00
Phil Sutter
4ca3803f81 MIPS: RB532: Remove {get,set}_434_reg()
These kernel symbols are unused. Also, since dev3 init has been moved to
devices.c, set_434_reg() breaks compiling as it uses dev3.

Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-01-30 21:33:00 +00:00
Phil Sutter
36f2db4b9c MIPS: RB532: Move dev3 init code to devices.c
This code doesn't belong to gpio.c, as it's completely unrelated to
GPIO. As dev1 and dev2 init code is in devices.c, it seems to be a more
adequate place.

Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-01-30 21:33:00 +00:00
Phil Sutter
7060886fb7 MIPS: RB532: Fix set_latch_u5()
The data to be written is just a byte, so use writeb instead of writel.
Also, dev3.base contains the address, not the data so referencing here
is wrong.

Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-01-30 21:33:00 +00:00
Phil Sutter
deb1003329 MIPS: RB532: Fix init of rb532_dev3_ctl_res
This register just contains the address of the actual resource, so
initialisation has to be the same as cf_slot0_res and nand_slot0_res.

Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-01-30 21:33:00 +00:00
Phil Sutter
94d2cc1b8b MIPS: RB532: Use driver_data instead of platform_data
As the korina ethernet driver uses platform_get_drvdata() to extract the
driver specific data from the platform device, driver_data has to be
used here.

Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-01-30 21:33:00 +00:00
Phil Sutter
1452fc7d17 MIPS: RB532: Detect uart type, add platform device
Auto-detection works just fine, so use it instead of specifying the type
manually. Also define a platform device for the uart, as suggested by
David Daney.

Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-01-30 21:33:00 +00:00
Phil Sutter
84c2c562c1 MIPS: RB532: remove useless CF GPIO initialisation
As the pata-rb532-cf driver calls gpio_direction_input(), the calls to
rb532_gpio_set_func() and rb532_gpio_direction_input() are not needed since
the alternate function is automatically being disabled when changing the
GPIO pin direction.
The later two calls to rb532_gpio_set_{ilevel,istat}() are implicitly being
done by the IRQ initialisation of pata-rb532-cf.

Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-01-30 21:32:59 +00:00
Phil Sutter
33763d571d MIPS: RB532: Auto disable GPIO alternate function
When a driver calls gpio_set_direction_{input,output}(), it obviously
doesn't want the alternate function for that pin to be active (as the
direction would not matter in that case). This patch ensures alternate
function is disabled when the direction is being changed.

Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-01-30 21:32:59 +00:00
Phil Sutter
4aa0f4d726 MIPS: RB532: Add set_type() function to IRQ struct.
Interrupt Group 4 mapps the GPIO pins enabled as interrupt sources;
add defines to make this clear when addressing them later in code.

The mapped GPIOs support triggering on either level high or low. To
achieve this, the set_type() function calls rb532_gpio_set_ilevel() for
interrupts of the above mentioned group.

As there is no way to alter the triggering characteristics of the other
interrupts, accept level triggering on status high only. (This is just a
guess; but as the system boots fine and interrupt-driven devices (e.g.
serial console) work with no implications, it seems to be right.)

To clear a GPIO mapped IRQ, the source has to be cleared (i.e., the
interrupt status bit of the corresponding GPIO pin). This is done inside
rb532_disable_irq().

After applying these changes I could undo most of my former "fixes" to
pata-rb532-cf. Particularly all interrupt handling can be done
generically via set_irq_type() as it was before.

Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-01-30 21:32:59 +00:00
Phil Sutter
5379a5fdf3 MIPS: RB532: Fix bit swapping in rb532_set_bit()
The algorithm works unconditionally. If bitval is one, the first line is
a no op and the second line sets the bit at offset position. Vice versa,
if bitval is zero, the first line clears the bit at offset position and
the second line is a no op.

Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-01-30 21:32:59 +00:00
Phil Sutter
2e373952cc MIPS: RB532: Provide functions for gpio configuration
As gpiolib doesn't support pin multiplexing, it provides no way to
access the GPIOFUNC register. Also there is no support for setting
interrupt status and level. These functions provide access to them and
are needed by the CompactFlash driver.

Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-11-20 19:42:33 +00:00
Florian Fainelli
1b432840d0 MIPS: RB532: GPIO register offsets are relative to GPIOBASE
This patch fixes the wrong use of GPIO register offsets
in devices.c. To avoid further problems, use gpio_get_value
to return the NAND status instead of our own expanded code.

Also define the zero offset of the alternate function register to allow
consistent access.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-11-20 19:42:32 +00:00
Phil Sutter
bc4c4e832a MIPS: RB532: Disable the right device
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-10-27 16:18:29 +00:00
Florian Fainelli
fa36b04386 MIPS: RB532: Set gpio interrupt status and level for CompactFlash
This patch sets the correct interrupt status and level
in order to get the CompactFlash adapter working.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-10-27 16:18:26 +00:00
Shinya Kuribayashi
08da6f1bdd MIPS: Kill unused <asm/debug.h> inclusions
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-10-15 12:46:52 +01:00
Florian Fainelli
d888e25b8d MIPS: RB532: Convert to GPIO lib
This patch converts the rb532 code to use gpio library
and register its gpio chip.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-10-11 16:18:47 +01:00
Florian Fainelli
606a083b1e MIPS: RB532: Cleanup the headers again
This patch cleans up headers and regroups informations to
where they should reside. While moving, try to have a
consistant naming for defines.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-10-11 16:18:46 +01:00
Florian Fainelli
deeb45ac4a MIPS: RB532: Remove obsolute reference to setup_serial_port
We are no longer using setup_serial_port. So just remove it
from the prom code.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-10-11 16:18:46 +01:00
Florian Fainelli
b6e2f58a50 MIPS: RB532: Fix id usage in platform devices
When there is only platform device of the same type, id = -1
should be used, fix this.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-10-11 16:18:46 +01:00
Florian Fainelli
c76befc342 MIPS: RB532: replace raw volatile read with a readl
This patch replaces a raw read using volatiles
with a readl.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-10-11 16:18:45 +01:00
Florian Fainelli
49afa0a151 MIPS: RB532: Remove gpio bootup state
We are no longer using gpio bootup state, so do not export
it and do not parse the kernel command line tag for it.
Instead we provide gpio-keys for the button the gpio bootup
state was checking.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-10-11 16:18:45 +01:00
Florian Fainelli
3c8cf8caa5 MIPS: RB532: Use physical addresses for gpio and device controller registers
This patch fixes the misuse of virtual addresses for the GPIO and third
device controller which would lead to problems while accessing ioremap'd
registers.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-10-11 16:18:45 +01:00
Florian Fainelli
3cd4e067a3 MIPS: RB532: Cleanup and group definitions to their right places
This patch moves GPIO related definitions to gpio.h and IRQ
related to irq.h

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-10-11 16:18:44 +01:00
Florian Fainelli
1ddfe82dc6 [MIPS] RB532: Do not define registers that are already defined
Use the register definitions of the MPMC controller from
mach-rc32434/rb.h instead of redefining them.

Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-08-26 09:10:26 +01:00
Adrian Bunk
8b32d6d00c [MIPS] RB532: Flags are unsigned long
A recent generic change now catches such bugs:

<--  snip  -->

...
  CC      arch/mips/rb532/time.o
cc1: warnings being treated as errors
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/mips/rb532/time.c: In function 'plat_time_init':
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/mips/rb532/time.c:55: error: comparison of distinct pointer types lacks a cast
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/mips/rb532/time.c:66: error: comparison of distinct pointer types lacks a cast
make[2]: *** [arch/mips/rb532/time.o] Error 1

<--  snip  -->

Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-07-30 21:54:34 +01:00
Ralf Baechle
73b4390fb2 [MIPS] Routerboard 532: Support for base system
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-07-20 14:38:18 +01:00