Implement the three IPIs (resched, single and cpu-mask) generation
and interrupt handler catch. The sun4m has 15 soft-IRQs and three
of them is used with this patch, the three IPIs was previously
implemented with the cross-call IRQ15 which does not work with
locking routines such as spinlocks because IRQ15 is NMI, it may
cause deadlock.
The IRQ trap handler code assumes (in the same spritit as the old
it seems) that hard interrupts will be generated until handled
(level), when a IRQ happens the IRQ pending register is checked
for pending soft-IRQs. When both hard and soft IRQ happens at the
same time only soft-IRQs are handled.
The old code implemented a soft-IRQ traphandler at IRQ14 which
called smp_reschedule_irq which in turn called set_need_resched.
It seems to be an old relic and is replaced with the interrupt
traphander exit code RESTORE_ALL, it calls schedule() when
appropriate.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements SMP IPIs on LEON using software generated
IRQs to signal between CPUs.
The IPI IRQ number is set by using the ipi_num property in the
device tree, or defaults to 13. LEON SMP systems should reserve
IRQ 13 (and IRQ 15) to Linux in order for the defaults to work.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current sparc32 SMP IPI generation is implemented the
cross call function. The cross call function uses IRQ15 the
NMI, this is has the effect that IPIs will interrupt IRQ
critical areas and hang the system. Typically on/after
spin_lock_irqsave calls can be aborted.
The cross call functionality must still exist to flush
cache/TLBS.
This patch provides CPU models a custom way to implement
generation of IPIs on the generic code's request. The
typical approach is to generate an IRQ for each IPI case.
After this patch each sparc32 SMP CPU model needs to
implement IPIs in order to function properly.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds {read,write}*_be big endian memory access
routines to the io.h header used on SPARC32 and SPARC64.
Tested on SPARC32 (LEON)
Signed-off-by: Jan Andersson <jan@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we are in the label cc_dword_align, registers %o0 and %o1 have the same last 2 bits,
but it's not guaranteed one of them is zero. So we can get unaligned memory access
in label ccte. Example of parameters which lead to this:
%o0=0x7ff183e9, %o1=0x8e709e7d, %g1=3
With the parameters I had a memory corruption, when the additional 5 bytes were rewritten.
This patch corrects the error.
One comment to the patch. We don't care about the third bit in %o1, because cc_end_cruft
stores word or less.
Signed-off-by: Tkhai Kirill <tkhai@yandex.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a multiple message send syscall and is the send
version of the existing recvmmsg syscall. This is heavily
based on the patch by Arnaldo that added recvmmsg.
I wrote a microbenchmark to test the performance gains of using
this new syscall:
http://ozlabs.org/~anton/junkcode/sendmmsg_test.c
The test was run on a ppc64 box with a 10 Gbit network card. The
benchmark can send both UDP and RAW ethernet packets.
64B UDP
batch pkts/sec
1 804570
2 872800 (+ 8 %)
4 916556 (+14 %)
8 939712 (+17 %)
16 952688 (+18 %)
32 956448 (+19 %)
64 964800 (+20 %)
64B raw socket
batch pkts/sec
1 1201449
2 1350028 (+12 %)
4 1461416 (+22 %)
8 1513080 (+26 %)
16 1541216 (+28 %)
32 1553440 (+29 %)
64 1557888 (+30 %)
We see a 20% improvement in throughput on UDP send and 30%
on raw socket send.
[ Add sparc syscall entries. -DaveM ]
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
include/linux/perf_event.h
Merge reason: pick up the latest jump-label enhancements, they are cooked ready.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* proper initialization of boot_cpu_id (no hardcoding to 0)
* use boot_cpu_id index to address into the IRQ controller where
appropriate
Each CPU has a separate set of IRQ controller registers, this
patch makes sure that the boot-cpu registers are used instead
of CPU0's.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define boot_cpu_id in single-processor kernels as well. This is
to support architectures which can boot on other than CPU0.
Sam Ravnborg has written the cleanup parts by extracting
boot_cpu_id from smp_32.c into setup_32.c and cleaned up
sun4d_irq.c.
boot_cpu_id was initialized before BSS was cleared in
sun4c_continue_boot, instead boot_cpu_id is set to 0xff to
avoid BSS. If boot_cpu_id is untouched (0xff) by bootup code
it will be overwritten to 0. boot_cpu_id4 is automatically
calculated in common code.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sparcstation 5 I have available has no MID property for the CPU.
This resulted in a panic when booting a SMP kernel on this box.
The assigned field in cpu_data is never used, so if we fail
to read the MID property then inform user and continue booting.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following warning:
mm/percpu.c: In function 'pcpu_embed_first_chunk':
mm/percpu.c:1647:3: warning: format '%lx' expects type 'long unsigned int', but argument 3 has type 'unsigned int'
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
[sam: added warning message to changelog, use _AC()]
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not require user to add "-p" to boot arguments to see
early info printed to prom console.
This is similar to the sparc64 functionality - which was added with:
3c62a2d347 ("[SPARC64]: Always register
a PROM based early console.")
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We did a cpu_probe() call each time a CPU got online - which
only effect was to save latest CPU/FPU info for use by show_cpuinfo().
Use same setup as for sparc64 where we probe for this info during startup,
and only once.
This allowed us to annotate a few functions __init which again
fixed the following section mismatch warnings:
WARNING: vmlinux.o(.text+0x65f0): Section mismatch in reference from the function set_cpu_and_fpu() to the (unknown reference) .init.rodata:(unknown)
WARNING: vmlinux.o(.text+0x65f8): Section mismatch in reference from the function set_cpu_and_fpu() to the (unknown reference) .init.rodata:(unknown)
WARNING: vmlinux.o(.text+0x664c): Section mismatch in reference from the function set_cpu_and_fpu() to the variable .init.rodata:manufacturer_info
WARNING: vmlinux.o(.text+0x6650): Section mismatch in reference from the function set_cpu_and_fpu() to the variable .init.rodata:manufacturer_info
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have all the cpu related info in cpu.c - so move
the remaining functions to support /proc/cpuinfo to this file.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In all cases there were a struct of_device_id variable defined __initdata.
But it was referenced from struct platform_driver.of_match_table
which is not guaranteed to be used during init only.
So drop the __initdata annotation.
This fixes following warnings:
WARNING: arch/sparc/kernel/built-in.o(.data+0x810): Section mismatch in reference from the variable clock_driver to the variable .init.data:clock_match
The variable clock_driver references
the variable __initdata clock_match
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
WARNING: arch/sparc/kernel/built-in.o(.data+0xcec): Section mismatch in reference from the variable apc_driver to the variable .init.data:apc_match
The variable apc_driver references
the variable __initdata apc_match
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
WARNING: arch/sparc/kernel/built-in.o(.data+0xd60): Section mismatch in reference from the variable pmc_driver to the variable .init.data:pmc_match
The variable pmc_driver references
the variable __initdata pmc_match
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A simple implementation of CPU affinity, the first CPU in
the affinity CPU mask always takes the IRQ.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleaned up leon_init_timers() by removing unnecessary double checking
and one indentation level. Changed LEON_IMASK to LEON_IMASK(cpu).
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The extended IRQ controller gives the LEON 16 more IRQs.
The patch installs a custom handler for the exetended controller
IRQ, where a register is read and the "real" IRQ causing IRQ is
determined.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LEON interrupt controller has one single mask register for all
IRQs per CPU, even though the genirq layer protects us from accessing
the same IRQ at the same time other IRQs share the same mask register
and may thus interfere. Some other IRQ controllers has a mask register
or similar per IRQ instead which makes spinlocks unncessary.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conversion of sparc32 to genirq is based on original work done
by David S. Miller.
Daniel Hellstrom has helped in the conversion and implemented
the shutdowm functionality.
Marcel van Nies <morcles@gmail.com> has tested this on Sparc Station 20
Test status:
sun4c - not tested
sun4m,pci - not tested
sun4m,sbus - tested (Sparc Classic, Sparc Station 5, Sparc Station 20)
sun4d - not tested
leon - tested on various combinations of leon boards,
including SMP variants
generic
Introduce use of GENERIC_HARDIRQS and GENERIC_IRQ_SHOW
Allocate 64 IRQs - which is enough even for SS2000
Use a table of irq_bucket to maintain uses IRQs
irq_bucket is also used to chain several irq's that
must be called when the same intrrupt is asserted
Use irq_link to link a interrupt source to the irq
All plafforms must now supply their own build_device_irq method
handler_irq rewriten to use generic irq support
floppy
Read FLOPPY_IRQ from platform device
Use generic request_irq to register the floppy interrupt
Rewrote sparc_floppy_irq to use the generic irq support
pcic:
Introduce irq_chip
Store mask in chip_data for use in mask/unmask functions
Add build_device_irq for pcic
Use pcic_build_device_irq in pci_time_init
allocate virtual irqs in pcic_fill_irq
sun4c:
Introduce irq_chip
Store mask in chip_data for use in mask/unmask functions
Add build_device_irq for sun4c
Use sun4c_build_device_irq in sun4c_init_timers
sun4m:
Introduce irq_chip
Introduce dedicated mask/unmask methods
Introduce sun4m_handler_data that allow easy access to necessary
data in the mask/unmask functions
Add a helper method to enable profile_timer (used from smp)
Added sun4m_build_device_irq
Use sun4m_build_device_irq in sun4m_init_timers
TODO:
There is no replacement for smp_rotate that always scheduled
next CPU as interrupt target upon an interrupt
sun4d:
Introduce irq_chip
Introduce dedicated mask/unmask methods
Introduce sun4d_handler_data that allow easy access to
necessary data in mask/unmask fuctions
Rewrote sun4d_handler_irq to use generic irq support
TODO:
The original implmentation of enable/disable had:
if (irq < NR_IRQS)
return;
The new implmentation does not distingush between SBUS and cpu
interrupts.
I am no sure what is right here. I assume we need to do
something for the cpu interrupts.
I have not succeeded booting my sun4d box (with or without this patch)
and my understanding of this platfrom is limited.
So I would be a bit suprised if this works.
leon:
Introduce irq_chip
Store mask in chip_data for use in mask/unmask functions
Add build_device_irq for leon
Use leon_build_device_irq in leon_init_timers
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Daniel Hellstrom <daniel@gaisler.com>
Tested-by: Daniel Hellstrom <daniel@gaisler.com>
Tested-by: Marcel van Nies <morcles@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the ifdeffery to a header file to make the logic more
obvious where we decide between PCI or SBUS init
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new name reflects the actual usage much better.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For future rework of try_to_wake_up() we'd like to push part of that
function onto the CPU the task is actually going to run on.
In order to do so we need a generic callback from the existing scheduler IPI.
This patch introduces such a generic callback: scheduler_ipi() and
implements it as a NOP.
BenH notes: PowerPC might use this IPI on offline CPUs under rare conditions!
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reviewed-by: Frank Rowand <frank.rowand@am.sony.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20110405152728.744338123@chello.nl
This compile error triggers on Sparc64:
kernel/sched.c:7140: error: 'cpu_coregroup_mask' undeclared here (not in a function)
Because after the recent scheduler domain cleanups the scheduler
uses this arch method as a function pointer in a scheduler
topology data structure - which is not possible with a macro.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20110412140040.3020ef55.sfr@canb.auug.org.au
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Introduce:
static __always_inline bool static_branch(struct jump_label_key *key);
instead of the old JUMP_LABEL(key, label) macro.
In this way, jump labels become really easy to use:
Define:
struct jump_label_key jump_key;
Can be used as:
if (static_branch(&jump_key))
do unlikely code
enable/disale via:
jump_label_inc(&jump_key);
jump_label_dec(&jump_key);
that's it!
For the jump labels disabled case, the static_branch() becomes an
atomic_read(), and jump_label_inc()/dec() are simply atomic_inc(),
atomic_dec() operations. We show testing results for this change below.
Thanks to H. Peter Anvin for suggesting the 'static_branch()' construct.
Since we now require a 'struct jump_label_key *key', we can store a pointer into
the jump table addresses. In this way, we can enable/disable jump labels, in
basically constant time. This change allows us to completely remove the previous
hashtable scheme. Thanks to Peter Zijlstra for this re-write.
Testing:
I ran a series of 'tbench 20' runs 5 times (with reboots) for 3
configurations, where tracepoints were disabled.
jump label configured in
avg: 815.6
jump label *not* configured in (using atomic reads)
avg: 800.1
jump label *not* configured in (regular reads)
avg: 803.4
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20110316212947.GA8792@redhat.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Suggested-by: H. Peter Anvin <hpa@linux.intel.com>
Tested-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc32: Pass task_struct to schedule_tail() in ret_from_fork
apbuart: Depend upon sparc.
sparc64: Fix section mis-match errors.
sparc32,leon: Fixed APBUART frequency detection
sparc32, leon: APBUART driver must use archdata to get IRQ number
sparc: Hook up syncfs system call.
We have to pass task_struct of previous process to function
schedule_tail(). Currently in ret_from_fork previous thread_info
is passed:
switch_to: mov %g6, %g3 /* previous thread_info in g6 */
ret_from_fork: call schedule_tail
mov %g3, %o0 /* previous thread_info is passed */
void schedule_tail(struct task_struct *prev);
Signed-off-by: Tkhai Kirill <tkhai@yandex.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix all of the problems spotted by CONFIG_DEBUG_SECTION_MISMATCH under
arch/sparc during a 64-bit defconfig build.
They fall into two categorites:
1) of_device_id is marked as __initdata, and we can never do this
since these objects sit in the device core data structures way
past boot. So even if a driver will never be reloaded, we have
to keep the device ID table around.
Mark such cases const instead.
2) The bootmem alloc/free handling code in mdesc.c was not fully
marked __init as it should be, thus generating a reference
to free_bootmem_late() (which is __init) from non-__init code.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the new features in genirq:
1) Set the chip flag IRCHIP_EOI_IF_HANDLED, which ensures in the
core code that irq_eoi() is only called when the interrupt was
handled. That removes the extra status check in the callback.
2) Use the preflow handler, which is called from the fasteoi core code
before the device handler. That avoids another status check and the
open coded handler redirection.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: sparclinux@vger.kernel.org
Commit ddd588b5dd ("oom: suppress nodes that are not allowed from
meminfo on oom kill") moved lib/show_mem.o out of lib/lib.a, which
resulted in build warnings on all architectures that implement their own
versions of show_mem():
lib/lib.a(show_mem.o): In function `show_mem':
show_mem.c:(.text+0x1f4): multiple definition of `show_mem'
arch/sparc/mm/built-in.o:(.text+0xd70): first defined here
The fix is to remove __show_mem() and add its argument to show_mem() in
all implementations to prevent this breakage.
Architectures that implement their own show_mem() actually don't do
anything with the argument yet, but they could be made to filter nodes
that aren't allowed in the current context in the future just like the
generic implementation.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: James Bottomley <James.Bottomley@hansenpartnership.com>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During the preparation for testing the recent changes made to the SUN4D
specific code in the kernel by Sam Ravnborg the following was discovered:
Since the removal of of_platform_bus_type (commit: eca3930163 )
multiboard SUN4Ds have not been able to boot. The kernel crashes due to a
zero-pointer error encountered when registering multiple M48T59 RTCs
(There is one on each board).
A patch for the was previously submitted, but the problem was not a
serious at that time, as it would only generate warnings. Now the kernel
will crash and stop executing before the serial console has been started.
(Crash output can be viewed by using the -p boot flag)
Signed-off-by: Kjetil Oftedal <oftedal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Percpu allocator honors alignment request upto PAGE_SIZE and both the
percpu addresses in the percpu address space and the translated kernel
addresses should be aligned accordingly. The calculation of the
former depends on the alignment of percpu output section in the kernel
image.
The linker script macros PERCPU_VADDR() and PERCPU() are used to
define this output section and the latter takes @align parameter.
Several architectures are using @align smaller than PAGE_SIZE breaking
percpu memory alignment.
This patch removes @align parameter from PERCPU(), renames it to
PERCPU_SECTION() and makes it always align to PAGE_SIZE. While at it,
add PCPU_SETUP_BUG_ON() checks such that alignment problems are
reliably detected and remove percpu alignment comment recently added
in workqueue.c as the condition would trigger BUG way before reaching
there.
For um, this patch raises the alignment of percpu area. As the area
is in .init, there shouldn't be any noticeable difference.
This problem was discovered by David Howells while debugging boot
failure on mn10300.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: uclinux-dist-devel@blackfin.uclinux.org
Cc: David Howells <dhowells@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: user-mode-linux-devel@lists.sourceforge.net
There is no user now.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: David Miller <davem@davemloft.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
minix bit operations are only used by minix filesystem and useless by
other modules. Because byte order of inode and block bitmaps is different
on each architecture like below:
m68k:
big-endian 16bit indexed bitmaps
h8300, microblaze, s390, sparc, m68knommu:
big-endian 32 or 64bit indexed bitmaps
m32r, mips, sh, xtensa:
big-endian 32 or 64bit indexed bitmaps for big-endian mode
little-endian bitmaps for little-endian mode
Others:
little-endian bitmaps
In order to move minix bit operations from asm/bitops.h to architecture
independent code in minix filesystem, this provides two config options.
CONFIG_MINIX_FS_BIG_ENDIAN_16BIT_INDEXED is only selected by m68k.
CONFIG_MINIX_FS_NATIVE_ENDIAN is selected by the architectures which use
native byte order bitmaps (h8300, microblaze, s390, sparc, m68knommu,
m32r, mips, sh, xtensa). The architectures which always use little-endian
bitmaps do not select these options.
Finally, we can remove minix bit operations from asm/bitops.h for all
architectures.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Michal Simek <monstr@monstr.eu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As the result of conversions, there are no users of ext2 non-atomic bit
operations except for ext2 filesystem itself. Now we can put them into
architecture independent code in ext2 filesystem, and remove from
asm/bitops.h for all architectures.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce little-endian bit operations to the big-endian architectures
which do not have native little-endian bit operations and the
little-endian architectures. (alpha, avr32, blackfin, cris, frv, h8300,
ia64, m32r, mips, mn10300, parisc, sh, sparc, tile, x86, xtensa)
These architectures can just include generic implementation
(asm-generic/bitops/le.h).
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Zankel <chris@zankel.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This introduces CONFIG_GENERIC_FIND_BIT_LE to tell whether to use generic
implementation of find_*_bit_le() in lib/find_next_bit.c or not.
For now we select CONFIG_GENERIC_FIND_BIT_LE for all architectures which
enable CONFIG_GENERIC_FIND_NEXT_BIT.
But m68knommu wants to define own faster find_next_zero_bit_le() and
continues using generic find_next_{,zero_}bit().
(CONFIG_GENERIC_FIND_NEXT_BIT and !CONFIG_GENERIC_FIND_BIT_LE)
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All architectures can use the common dma_addr_t typedef now. We can
remove the arch specific dma_addr_t.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a node parameter to alloc_thread_info(), and change its name to
alloc_thread_info_node()
This change is needed to allow NUMA aware kthread_create_on_cpu()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tejun Heo <tj@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Similarly to irq_of_parse_and_map(), find the platform_device
object and return the pre-computed resource.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'kvm-updates/2.6.39' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (55 commits)
KVM: unbreak userspace that does not sets tss address
KVM: MMU: cleanup pte write path
KVM: MMU: introduce a common function to get no-dirty-logged slot
KVM: fix rcu usage in init_rmode_* functions
KVM: fix kvmclock regression due to missing clock update
KVM: emulator: Fix permission checking in io permission bitmap
KVM: emulator: Fix io permission checking for 64bit guest
KVM: SVM: Load %gs earlier if CONFIG_X86_32_LAZY_GS=n
KVM: x86: Remove useless regs_page pointer from kvm_lapic
KVM: improve comment on rcu use in irqfd_deassign
KVM: MMU: remove unused macros
KVM: MMU: cleanup page alloc and free
KVM: MMU: do not record gfn in kvm_mmu_pte_write
KVM: MMU: move mmu pages calculated out of mmu lock
KVM: MMU: set spte accessed bit properly
KVM: MMU: fix kvm_mmu_slot_remove_write_access dropping intermediate W bits
KVM: Start lock documentation
KVM: better readability of efer_reserved_bits
KVM: Clear async page fault hash after switching to real mode
KVM: VMX: Initialize vm86 TSS only once.
...
Make __get_user_pages return -EHWPOISON for HWPOISON page only if
FOLL_HWPOISON is specified. With this patch, the interested callers
can distinguish HWPOISON pages from general FAULT pages, while other
callers will still get -EFAULT for all these pages, so the user space
interface need not to be changed.
This feature is needed by KVM, where UCR MCE should be relayed to
guest for HWPOISON page, while instruction emulation and MMIO will be
tried for general FAULT page.
The idea comes from Andrew Morton.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
When we try to handle vmalloc faults, we can take a code
path which uses "code" before we actually set it.
Amusingly gcc-3.3 notices this yet gcc-4.x does not.
Reported-by: Bob Breuer <breuerr@mc.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
gas used to accept (and ignore?) .size directives which referred to
undefined symbols, as this does. In binutils 2.21 these are treated
as errors.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the warnings emitted (we fail arch/sparc file
builds with -Werror) were legitimate but harmless, however
one case (n2_pcr_write) was a genuine bug.
Based almost entirely upon a patch by Sam Ravnborg.
Reported-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
entry.S access percpu + global data defined in
sun4m_irq.c - so move the types to irq.h.
This makes sparse happy and allow us to utilize
asm-offsets later.
Also updated a few comments in the sun4m_irq.c file.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
build_device_irq() is used to encapsulate the plaform
specific details when we build an irq.
For now the default is a simple 1:1 but sun4d differs.
This patch refactors functionality - but does not change
the existing functionality.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
sparc_irq_config is used to hold the platform specific irq setup.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a few includes back required to build with floppy enabled
Fix declaration of trapbase_cpu* so it is now consistent
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts the sparc clocksources to use clocksource_register_hz/khz
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent patch to the x86 randomization code caused me to take
a quick look at what we do on sparc64, and in doing so I noticed
that we sometimes calculate a non-page-aligned randomization value
and stick it into mmap_base.
I also noticed that since I copied the logic over from PowerPC,
the powerpc code has tweaked the randomization ranges in ways that
would benefit us as well.
For one thing, we should allow up to at least 8MB of randomization
otherwise huge-page regions when HPAGE_SIZE is 4MB never randomize
at all.
And on the 64-bit side we were using up to 4GB. Tone it down to
1GB as 4GB can result in a lot of address space wastage.
Finally, make sure all computations are unsigned.
Signed-off-by: David S. Miller <davem@davemloft.net>
- drop filename in file header
- drop unused includes
- add KERN_* to printk
- fix spaces => tabs
- add spaces after reserved words
- drop all externs, they are now in header files
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This looked like a bug to me.
Add a comment so next reader is hopefully less confused.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The preprocessor symbol was not defined and the code
was therefore not in use.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- drop filename in file header
- drop unused includes
- add description of sun4d interrupts (from davem)
- add KERN_* to printk
- fix spaces => tabs
- add spaces after reserved words
- fix indent of a whole code block in smp4d_boot_one_cpu()
Note: two printk() was updated from debug to KERN_INFO in this code block
- drop all externs, they are now in header files
This is partly based on a patch from: David Miller <davem@davemloft.net>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- drop filename in file header
- drop unused includes
- add description of sun4m interrupts (from davem)
- add KERN_* to printk
- fix spaces => tabs
- add spaces after reserved words
- drop all externs, they are now in header files
This is partly based on a patch from: David Miller <davem@davemloft.net>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- drop filename in header
- drop unused includes
- add description of sun4c interrupts (from davem)
- add spaces after reserved words
This is partly based on a patch from: David Miller <davem@davemloft.net>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for cleaning up a number of files add
declarations for irq and smp related data/functions to
the relevant headers.
This showed that the extern declaration of cputypval differed
in the two files where it was used.
As cputypval is defined like this:
cputypval:
.asciz "sun4c"
the correct representation is a char array.
Fix users to use the new declaration.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The two methods included in tick14.c was nop because
the static variable linux_lvl14 was always NULL.
So remove the file and callers.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The way a LEON is powered down is implemented differently depending
on CHIP type. The AMBA Plug&Play system ID tells revision of GRLIB
and CHIP.
This is for example needed by the GR-LEON4-ITX board and the UT699.
Previously the power down support for LEON was limited to SMP, now
both SMP and UP systems use the instruction.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is only for LEON as u-boot for SPARC only supports LEON.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic irq support uses the term 'irq' for the
allocated irq number.
Fix it so sparc64 use the same term for an irq as the
generic irq support does.
For a naive reader this is less confusing.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic irq support uses the term 'irq' for the
allocated irq number.
Fix it so sparc64 use the same term for an irq as the
generic irq support does.
For a naive reader this is less confusing.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop all uses of deprecated genirq features.
The irq_set_affinity() call got a third paramter 'force'
which is unused.
For now genirq does not use this paramter and it is
ignored by sparc.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Josip Rodin <joy@entuzijast.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
{get,set}_irq_data uses the member "handler_data" in irq_data
which fits the naem of the datatype.
The change has no functional impact
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of moving to use irq_data.handler_data rename
all pointers to irq_handler_data "handler_data".
This will also prevent name clash when we introduce the
new irq methods.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic irq support uses "irq" to identify the
virtual irq number. To avoid confusion rename the
argument to handler_irq() to pil to match the
name of the parameter in the PCR register.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
GENERIC_HARDIRQS_NO_DEPRECATED require us to access data via irq_data.
No functional changes as data has same layout due to use of union
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Order of kfree and free_pages were swapped in the error handling.
Signed-off-by: Kristoffer Glembo <kristoffer@gaisler.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kristoffer Glembo <kristoffer@gaisler.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets the dma_ops structure for LEON. It reuses the pci32_dma_ops.
Signed-off-by: Kristoffer Glembo <kristoffer@gaisler.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kristoffer Glembo <kristoffer@gaisler.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kristoffer Glembo <kristoffer@gaisler.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (76 commits)
pch_uart: reference clock on CM-iTC
pch_phub: add new device ML7213
n_gsm: fix UIH control byte : P bit should be 0
n_gsm: add a documentation
serial: msm_serial_hs: Add MSM high speed UART driver
tty_audit: fix tty_audit_add_data live lock on audit disabled
tty: move cd1865.h to drivers/staging/tty/
Staging: tty: fix build with epca.c driver
pcmcia: synclink_cs: fix prototype for mgslpc_ioctl()
Staging: generic_serial: fix double locking bug
nozomi: don't use flush_scheduled_work()
tty/serial: Relax the device_type restriction from of_serial
MAINTAINERS: Update HVC file patterns
tty: phase out of ioctl file pointer for tty3270 as well
tty: forgot to remove ipwireless from drivers/char/pcmcia/Makefile
pch_uart: Fix DMA channel miss-setting issue.
pch_uart: fix exclusive access issue
pch_uart: fix auto flow control miss-setting issue
pch_uart: fix uart clock setting issue
pch_uart : Use dev_xxx not pr_xxx
...
Fix up trivial conflicts in drivers/misc/pch_phub.c (same patch applied
twice, then changes to the same area in one branch)
* 'for-2.6.39' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu, x86: Add arch-specific this_cpu_cmpxchg_double() support
percpu: Generic support for this_cpu_cmpxchg_double()
alpha: use L1_CACHE_BYTES for cacheline size in the linker script
percpu: align percpu readmostly subsection to cacheline
Fix up trivial conflict in arch/x86/kernel/vmlinux.lds.S due to the
percpu alignment having changed ("x86: Reduce back the alignment of the
per-CPU data section")
[AV: on architectures where default conflicts with existing
flags, that is]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (62 commits)
posix-clocks: Check write permissions in posix syscalls
hrtimer: Remove empty hrtimer_init_hres_timer()
hrtimer: Update hrtimer->state documentation
hrtimer: Update base[CLOCK_BOOTTIME].offset correctly
timers: Export CLOCK_BOOTTIME via the posix timers interface
timers: Add CLOCK_BOOTTIME hrtimer base
time: Extend get_xtime_and_monotonic_offset() to also return sleep
time: Introduce get_monotonic_boottime and ktime_get_boottime
hrtimers: extend hrtimer base code to handle more then 2 clockids
ntp: Remove redundant and incorrect parameter check
mn10300: Switch do_timer() to xtimer_update()
posix clocks: Introduce dynamic clocks
posix-timers: Cleanup namespace
posix-timers: Add support for fd based clocks
x86: Add clock_adjtime for x86
posix-timers: Introduce a syscall for clock tuning.
time: Splitout compat timex accessors
ntp: Add ADJ_SETOFFSET mode bit
time: Introduce timekeeping_inject_offset
posix-timer: Update comment
...
Fix up new system-call-related conflicts in
arch/x86/ia32/ia32entry.S
arch/x86/include/asm/unistd_32.h
arch/x86/include/asm/unistd_64.h
arch/x86/kernel/syscall_table_32.S
(name_to_handle_at()/open_by_handle_at() vs clock_adjtime()), and some
due to movement of get_jiffies_64() in:
kernel/time.c
Change futex_atomic_op_inuser and futex_atomic_cmpxchg_inatomic
prototypes to use u32 types for the futex as this is the data type the
futex core code uses all over the place.
Signed-off-by: Michel Lespinasse <walken@google.com>
Cc: Darren Hart <darren@dvhart.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <20110311025058.GD26122@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The cmpxchg_futex_value_locked API was funny in that it returned either
the original, user-exposed futex value OR an error code such as -EFAULT.
This was confusing at best, and could be a source of livelocks in places
that retry the cmpxchg_futex_value_locked after trying to fix the issue
by running fault_in_user_writeable().
This change makes the cmpxchg_futex_value_locked API more similar to the
get_futex_value_locked one, returning an error code and updating the
original value through a reference argument.
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com> [tile]
Acked-by: Tony Luck <tony.luck@intel.com> [ia64]
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michal Simek <monstr@monstr.eu> [microblaze]
Acked-by: David Howells <dhowells@redhat.com> [frv]
Cc: Darren Hart <darren@dvhart.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <20110311024851.GC26122@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Get rid of old users of of_platform_driver in arch/sparc. Most
of_platform_driver users can be converted to use the platform_bus
directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This is useful for system management software so that it can kick
off things like gettys and everything that's started from a tty,
before we reuse it from/for something else or shut it down.
Without this ioctl it would have to temporarily become the owner of
the tty, then call vhangup() and then give it up again.
Cc: Lennart Poettering <lennart@poettering.net>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Doing NMI startup as an early initcall doesn't work because we need
to have SMP started up by then.
So we'd only NMI startup one cpu, which causes perf PMU grab to
BUG because the nmi_active count isn't what it's supposed to be.
This also points out that we don't have proper CPU up/down notifiers
for the NMI code which will need to be fixed at some point.
Signed-off-by: David S. Miller <davem@davemloft.net>
iommu_alloc_ctx() finds a zero bit in iommu->ctx_bitmap. It starts
searching from iommu->ctx_lowest_free to the end of the bitmap.
But the size argument to find_next_zero_bit() in iommu_alloc_ctx()
is wrong. It should be the bitmap size, not the maximum size to
search from the offset argument.
Fortunately iommu->ctx_lowest_free is almost unused and it will not
be more than 1. So the bug wasted only 1-bit at the end of
iommu->ctx_bitmap.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Use bitmap_set() instead of calling __set_bit() each bit.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit f0e98c387e ("[SPARC]: Fix
link errors with gcc-4.3") the MNA trap handler does not emulate
stores to unaligned addresses correctly. MNA operation from both
kernel and user space are affected.
A typical effect of this bug is nr_frags in skbs are overwritten
during buffer copying/checksum-calculation, or maximally 6 bytes
of data in the network buffer will be overwitten with garbage.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xtime_update() takes the xtime_lock itself.
pcic_clear_clock_irq() and clear_clock_irq do not need
to be protected by xtime_lock.
Signed-off-by: Torben Hohn <torbenh@gmx.de>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: johnstul@us.ibm.com
Cc: hch@infradead.org
Cc: yong.zhang0@gmail.com
LKML-Reference: <20110127150022.23248.80369.stgit@localhost>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
All architecture specific rwsem headers carry the same function
prototypes. Just x86 adds asmregparm, which is an empty define on all
other architectures. S390 has a stale rwsem_downgrade_write()
prototype.
Remove the duplicates and add the prototypes to linux/rwsem.h
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Richard Henderson <rth@twiddle.net>
Acked-by: Tony Luck <tony.luck@intel.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: David Miller <davem@davemloft.net>
Cc: Chris Zankel <chris@zankel.net>
LKML-Reference: <20110126195833.970840140@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Instead of having the same implementation in each architecture, move
it to linux/rwsem.h and remove the duplicates. It's unlikely that an
arch will ever implement something different, but we can deal with
that when it happens.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Matt Turner <mattst88@gmail.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: David Miller <davem@davemloft.net>
Cc: Chris Zankel <chris@zankel.net>
LKML-Reference: <20110126195833.876773757@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The rwsem initializers and related macros and functions are mostly the
same. Some of them lack the lockdep initializer, but having it in
place does not matter for architectures which do not support lockdep.
powerpc, sparc, x86: No functional change
sh, s390: Removes the duplicate init_rwsem (inline and #define)
alpha, ia64, xtensa: Use the lockdep capable init function in
lib/rwsem.c which is just uninlining the init
function for the LOCKDEP=n case
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Matt Turner <mattst88@gmail.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: David Miller <davem@davemloft.net>
Cc: Chris Zankel <chris@zankel.net>
LKML-Reference: <20110126195833.771812729@linutronix.de>
The difference between these declarations is the data type of the
count member and the lack of lockdep in some architectures/
long is equivivalent to signed long and the #ifdef guarded dep_map
member does not hurt anyone.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Matt Turner <mattst88@gmail.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: David Miller <davem@davemloft.net>
Cc: Chris Zankel <chris@zankel.net>
LKML-Reference: <20110126195833.679641914@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
All rwsem implementations include the same headers. Include them from
include/linux/rwsem.h
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Matt Turner <mattst88@gmail.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: David Miller <davem@davemloft.net>
Cc: Chris Zankel <chris@zankel.net>
LKML-Reference: <20110126195833.483520950@linutronix.de>
SPIN_LOCK_UNLOCK is deprecated. Use the lockdep capable variant
instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David S. Miller <davem@davemloft.net>
Currently percpu readmostly subsection may share cachelines with other
percpu subsections which may result in unnecessary cacheline bounce
and performance degradation.
This patch adds @cacheline parameter to PERCPU() and PERCPU_VADDR()
linker macros, makes each arch linker scripts specify its cacheline
size and use it to align percpu subsections.
This is based on Shaohua's x86 only patch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Shaohua Li <shaohua.li@intel.com>
All architectures are finally converted. Remove the cruft.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Michal Simek <monstr@monstr.eu>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Jeff Dike <jdike@addtoit.com>
pte alloc routines must wait for split_huge_page if the pmd is not present
and not null (i.e. pmd_trans_splitting). The additional branches are
optimized away at compile time by pmd_trans_splitting if the config option
is off. However we must pass the vma down in order to know the anon_vma
lock to wait for.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Four architectures (arm, mips, sparc, x86) use __vmalloc_area() for
module_init(). Much of the code is duplicated and can be generalized in a
globally accessible function, __vmalloc_node_range().
__vmalloc_node() now calls into __vmalloc_node_range() with a range of
[VMALLOC_START, VMALLOC_END) for functionally equivalent behavior.
Each architecture may then use __vmalloc_node_range() directly to remove
the duplication of code.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (29 commits)
of/flattree: forward declare struct device_node in of_fdt.h
ipmi: explicitly include of_address.h and of_irq.h
sparc: explicitly cast negative phandle checks to s32
powerpc/405: Fix missing #{address,size}-cells in i2c node
powerpc/5200: dts: refactor dts files
powerpc/5200: dts: Change combatible strings on localbus
powerpc/5200: dts: remove unused properties
powerpc/5200: dts: rename nodes to prepare for refactoring dts files
of/flattree: Update dtc to current mainline.
of/device: Don't register disabled devices
powerpc/dts: fix syntax bugs in bluestone.dts
of: Fixes for OF probing on little endian systems
of: make drivers depend on CONFIG_OF instead of CONFIG_PPC_OF
of/flattree: Add of_flat_dt_match() helper function
of_serial: explicitly include of_irq.h
of/flattree: Refactor unflatten_device_tree and add fdt_unflatten_tree
of/flattree: Reorder unflatten_dt_node
of/flattree: Refactor unflatten_dt_node
of/flattree: Add non-boottime device tree functions
of/flattree: Add Kconfig for EARLY_FLATTREE
...
Fix up trivial conflict in arch/sparc/prom/tree_32.c as per Grant.
Commit 004417a6d4
("perf, arch: Cleanup perf-pmu init vs lockup-detector")
move the perf events init to be an early_initcall.
But this won't work properly unless the dependencies for
this code initialize beforehand.
Fix it by making cpu_type_probe and pcr_arch_init be
an early_initcall as well.
Reported-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (36 commits)
serial: apbuart: Fixup apbuart_console_init()
TTY: Add tty ioctl to figure device node of the system console.
tty: add 'active' sysfs attribute to tty0 and console device
drivers: serial: apbuart: Handle OF failures gracefully
Serial: Avoid unbalanced IRQ wake disable during resume
tty: fix typos/errors in tty_driver.h comments
pch_uart : fix warnings for 64bit compile
8250: fix uninitialized FIFOs
ip2: fix compiler warning on ip2main_pci_tbl
specialix: fix compiler warning on specialix_pci_tbl
rocket: fix compiler warning on rocket_pci_ids
8250: add a UPIO_DWAPB32 for 32 bit accesses
8250: use container_of() instead of casting
serial: omap-serial: Add support for kernel debugger
serial: fix pch_uart kconfig & build
drivers: char: hvc: add arm JTAG DCC console support
RS485 documentation: add 16C950 UART description
serial: ifx6x60: fix memory leak
serial: ifx6x60: free IRQ on error
Serial: EG20T: add PCH_UART driver
...
Fixed up conflicts in drivers/serial/apbuart.c with evil merge that
makes the code look fairly sane (unlike either side).
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next-2.6: (25 commits)
atyfb: Fix bootup hangs on sparc64.
sparc: update copyright in piggyback.c
sparc: unify strip command in boot/Makefile
sparc: rename piggyback_32 to piggyback
sparc: fix tftpboot.img for sparc64 on little-endian host
sparc: add $BITS to piggyback arguments
sparc: remove obsolete ELF support in piggyback_32.c
sparc: additional comments to piggyback_32.c
sparc: use _start for the start entry (like 64 bit does)
sparc: use trapbase in setup_arch
sparc: refactor piggy_32.c
Added support for ampopts in APBUART driver. Used in AMP systems.
APBUART: added raw AMBA vendor/device number to match against.
SPARC/LEON: avoid AMBAPP name duplicates in openprom fs when REG is missing
SPARC/LEON: added support for selecting Timer Core and Timer within core
LEON: added raw AMBA vendor/device number to find TIMER, IRQCTRL
SPARC/LEON: added support for IRQAMP IRQ Controller
SPARC/LEON: find IRQCTRL and Timer via OF-Tree, instead of hardcoded.
sparc: fix sparse warnings in arch/sparc/prom for 32 bit build
sparc: remove unused prom tree functions
...
Update copyright info in piggyback.c to include
info from piggyback_64.c.
Include my own copyright too.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Josip Rodin <joy@entuzijast.net>
Cc: Jakub Jelinek <jakub@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include an additional "Kernel is ready" print for zImage
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we use the same piggyback for 32 and 64 bit
we can drop the _32 suffix.
Include some trivial unification in the Makefile
now that 32 and 64 bit can share the same piggyback command.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
piggyback_32 adapted to support sparc64:
- locating "HdrS" differs for sparc and sparc64
- sparc64 updates a_text, a_data + a_bss in the final a.out header
Updated Makefile to use piggyback_32 for sparc64.
Deleted the now unused piggyback_64.c
piggyback_32.c is host endian neutral and works on both
little-endian and big-endian hosts.
This fixes a long standing bug where sparc64 could not
generate tftpboot.img on a x86 host.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new option to piggyback that identify if this is
for 32 or 64 bit.
Use this information to determine the alignment used.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we always convert to a.out there is no need to
support ELF.
Removing ELF support because:
- it is not used
- it simplifies code to support a.out only
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reverse engineering the functionality of piggyback
I missed that the code was actually commented.
So I added a few comments.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use "_start" in 64 bit - do the same in 32 bit.
It is always good to be consistent.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
start and trapbase point to the same address.
But using start to assing to sparc_ttable looked confusing.
Replace this with the use of trapbase.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactoring to increase readability (a little).
- sort includes
- spaces around operators
- small helpers introduced
- added a few comments
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the REG property is not available the NODE-ID is used as an unique
identifier in order to avoid filesystem name duplicates in /proc/openprom
filesystem
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ability to select Timer Core and Timer instance for system clock
makes it possible for multiple AMP systems to coexist.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Needed for LEON AMP systems where different CPUs are routed to
different IRQ controllers. This patch selects the IRQ Controller
which has been routed to the boot CPU, it is up to the boot loader
to configure the IRQ controller.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we switched sparc from using 'int's to 'phandle's (which is a u32), we
neglected to do anything with the various checks for -1. For those tests,
explicitly cast the phandles to s32.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix following sparse warnings:
arch/sparc/prom/bootstr_32.c:32:35: warning: Using plain integer as NULL pointer
arch/sparc/prom/memory.c:61:13: warning: symbol 'prom_meminit' was not declared. Should it be static?
arch/sparc/prom/misc_32.c:74:1: error: symbol 'prom_halt' redeclared with different type (originally declared at arch/sparc/include/asm/oplib_32.h:67) - different modifiers
arch/sparc/prom/ranges.c:16:26: warning: symbol 'promlib_obio_ranges' was not declared. Should it be static?
arch/sparc/prom/ranges.c:17:5: warning: symbol 'num_obio_ranges' was not declared. Should it be static?
arch/sparc/prom/ranges.c:39:1: warning: symbol 'prom_adjust_ranges' was not declared. Should it be static?
arch/sparc/prom/ranges.c:69:13: warning: symbol 'prom_ranges_init' was not declared. Should it be static?
arch/sparc/prom/tree_32.c:286:22: warning: Using plain integer as NULL pointer
arch/sparc/prom/tree_32.c:286:38: warning: Using plain integer as NULL pointer
None of the warnings indicated any serious issues.
We are now sparse clean for 32 bit build in arch/sparc/prom.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the following unused funtions:
prom_nodematch()
prom_firstprop()
prom_node_has_property()
Also declare a few local functions static.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the following unused funtions:
prom_stopcpu()
prom_idlecpu()
prom_restartcpu()
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
