CalIOC2 is a PCI-e implementation of the Calgary logic. Most of the
programming details are the same, but some differ, e.g., TCE cache
flush. This patch introduces CalIOC2 support - detection and various
support routines. It's not expected to work yet (but will with
follow-on patches).
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... in preparation for doing it differently for CalIOC2.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Calgary and CalIOC2 share most of the same logic. Introduce struct
cal_chipset_ops for quirks and tce flush logic which are
[akpm@linux-foundation.org: make calgary_chip_ops static]
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... will be used by CalIOC2 later
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On x86_64 kernel, level triggered irq migration gets initiated in the
context of that interrupt(after executing the irq handler) and following
steps are followed to do the irq migration.
1. mask IOAPIC RTE entry; // write to IOAPIC RTE
2. EOI; // processor EOI write
3. reprogram IOAPIC RTE entry // write to IOAPIC RTE with new destination and
// and interrupt vector due to per cpu vector
// allocation.
4. unmask IOAPIC RTE entry; // write to IOAPIC RTE
Because of the per cpu vector allocation in x86_64 kernels, when the irq
migrates to a different cpu, new vector(corresponding to the new cpu) will
get allocated.
An EOI write to local APIC has a side effect of generating an EOI write for
level trigger interrupts (normally this is a broadcast to all IOAPICs).
The EOI broadcast generated as a side effect of EOI write to processor may
be delayed while the other IOAPIC writes (step 3 and 4) can go through.
Normally, the EOI generated by local APIC for level trigger interrupt
contains vector number. The IOAPIC will take this vector number and search
the IOAPIC RTE entries for an entry with matching vector number and clear
the remote IRR bit (indicate EOI). However, if the vector number is
changed (as in step 3) the IOAPIC will not find the RTE entry when the EOI
is received later. This will cause the remote IRR to get stuck causing the
interrupt hang (no more interrupt from this RTE).
Current x86_64 kernel assumes that remote IRR bit is cleared by the time
IOAPIC RTE is reprogrammed. Fix this assumption by checking for remote IRR
bit and if it still set, delay the irq migration to the next interrupt
arrival event(hopefully, next time remote IRR bit will get cleared before
the IOAPIC RTE is reprogrammed).
Initial analysis and patch from Nanhai.
Clean up patch from Suresh.
Rewritten to be less intrusive, and to contain a big fat comment by Eric.
[akpm@linux-foundation.org: fix comments]
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Nanhai Zou <nanhai.zou@intel.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Keith Packard <keith.packard@intel.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This helps to reduce the frequency at which the CPU must be taken out of a
lower-power state.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: Tim Hockin <thockin@hockin.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as921) adds code to the show_regs() routine in i386 and x86_64
to print the contents of the debug registers along with all the others.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Background:
The MCE handler has several paths that it can take, depending on various
conditions of the MCE status and the value of the 'tolerant' knob. The
exact semantics are not well defined and the code is a bit twisty.
Description:
This patch makes the MCE handler's behavior more clear by documenting the
behavior for various 'tolerant' levels. It also fixes or enhances
several small things in the handler. Specifically:
* If RIPV is set it is not safe to restart, so set the 'no way out'
flag rather than the 'kill it' flag.
* Don't panic() on correctable MCEs.
* If the _OVER bit is set *and* the _UC bit is set (meaning possibly
dropped uncorrected errors), set the 'no way out' flag.
* Use EIPV for testing whether an app can be killed (SIGBUS) rather
than RIPV. According to docs, EIPV indicates that the error is
related to the IP, while RIPV simply means the IP is valid to
restart from.
* Don't clear the MCi_STATUS registers until after the panic() path.
This leaves the status bits set after the panic() so clever BIOSes
can find them (and dumb BIOSes can do nothing).
This patch also calls nonseekable_open() in mce_open (as suggested by akpm).
Result:
Tolerant levels behave almost identically to how they always have, but
not it's well defined. There's a slightly higher chance of panic()ing
when multiple errors happen (a good thing, IMHO). If you take an MBE and
panic(), the error status bits are not cleared.
Alternatives:
None.
Testing:
I used software to inject correctable and uncorrectable errors. With
tolerant = 3, the system usually survives. With tolerant = 2, the system
usually panic()s (PCC) but not always. With tolerant = 1, the system
always panic()s. When the system panic()s, the BIOS is able to detect
that the cause of death was an MC4. I was not able to reproduce the
case of a non-PCC error in userspace, with EIPV, with (tolerant < 3).
That will be rare at best.
Signed-off-by: Tim Hockin <thockin@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Background:
/dev/mcelog is typically polled manually. This is less than optimal for
situations where accurate accounting of MCEs is important. Calling
poll() on /dev/mcelog does not work.
Description:
This patch adds support for poll() to /dev/mcelog. This results in
immediate wakeup of user apps whenever the poller finds MCEs. Because
the exception handler can not take any locks, it can not call the wakeup
itself. Instead, it uses a thread_info flag (TIF_MCE_NOTIFY) which is
caught at the next return from interrupt or exit from idle, calling the
mce_user_notify() routine. This patch also disables the "fake panic"
path of the mce_panic(), because it results in printk()s in the exception
handler and crashy systems.
This patch also does some small cleanup for essentially unused variables,
and moves the user notification into the body of the poller, so it is
only called once per poll, rather than once per CPU.
Result:
Applications can now poll() on /dev/mcelog. When an error is logged
(whether through the poller or through an exception) the applications are
woken up promptly. This should not affect any previous behaviors. If no
MCEs are being logged, there is no overhead.
Alternatives:
I considered simply supporting poll() through the poller and not using
TIF_MCE_NOTIFY at all. However, the time between an uncorrectable error
happening and the user application being notified is *the*most* critical
window for us. Many uncorrectable errors can be logged to the network if
given a chance.
I also considered doing the MCE poll directly from the idle notifier, but
decided that was overkill.
Testing:
I used an error-injecting DIMM to create lots of correctable DRAM errors
and verified that my user app is woken up in sync with the polling interval.
I also used the northbridge to inject uncorrectable ECC errors, and
verified (printk() to the rescue) that the notify routine is called and the
user app does wake up. I built with PREEMPT on and off, and verified
that my machine survives MCEs.
[wli@holomorphy.com: build fix]
Signed-off-by: Tim Hockin <thockin@google.com>
Signed-off-by: William Irwin <bill.irwin@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Background:
/dev/mcelog is a clear-on-read interface. It is currently possible for
multiple users to open and read() the device. Users are protected from
each other during any one read, but not across reads.
Description:
This patch adds support for O_EXCL to /dev/mcelog. If a user opens the
device with O_EXCL, no other user may open the device (EBUSY). Likewise,
any user that tries to open the device with O_EXCL while another user has
the device will fail (EBUSY).
Result:
Applications can get exclusive access to /dev/mcelog. Applications that
do not care will be unchanged.
Alternatives:
A simpler choice would be to only allow one open() at all, regardless of
O_EXCL.
Testing:
I wrote an application that opens /dev/mcelog with O_EXCL and observed
that any other app that tried to open /dev/mcelog would fail until the
exclusive app had closed the device.
Caveats:
None.
Signed-off-by: Tim Hockin <thockin@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we are in the emulated NUMA case, we need to make sure that all existing
apicid_to_node mappings that point to real node ID's now point to the
equivalent fake node ID's.
If we simply iterate over all apicid_to_node[] members for each node, we risk
remapping an entry if it shares a node ID with a real node. Since apicid's
may not be consecutive, we're forced to create an automatic array of
apicid_to_node mappings and then copy it over once we have finished remapping
fake to real nodes.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For NUMA emulation, our SLIT should represent the true NUMA topology of the
system but our proximity domain to node ID mapping needs to reflect the
emulated state.
When NUMA emulation has successfully setup fake nodes on the system, a new
function, acpi_fake_nodes() is called. This function determines the proximity
domain (_PXM) for each true node found on the system. It then finds which
emulated nodes have been allocated on this true node as determined by its
starting address. The node ID to PXM mapping is changed so that each fake
node ID points to the PXM of the true node that it is located on.
If the machine failed to register a SLIT, then we assume there is no special
requirement for emulated node affinity so we use the default LOCAL_DISTANCE,
which is newly exported to this code, as our measurement if the emulated nodes
appear in the same PXM. Otherwise, we use REMOTE_DISTANCE.
PXM_INVAL and NID_INVAL are also exported to the ACPI header file so that we
can compare node_to_pxm() results in generic code (in this case, the SRAT
code).
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The logic in e820_find_active_regions() for determining the true active
regions for an e820 entry given a range of PFN's is needed for
e820_hole_size() as well.
e820_hole_size() is called from the NUMA emulation code to determine the
reserved area within an address range on a per-node basis. Its logic should
duplicate that of finding active regions in an e820 entry because these are
the only true ranges we may register anyway.
[akpm@linux-foundation.org: cleanup]
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds caching of pgds and puds, pmds, pte. That way we can avoid costly
zeroing and initialization of special mappings in the pgd.
A second quicklist is useful to separate out PGD handling. We can carry the
initialized pgds over to the next process needing them.
Also clean up the pgd_list handling to use regular list macros. There is no
need anymore to avoid the lru field.
Move the add/removal of the pgds to the pgdlist into the constructor /
destructor. That way the implementation is congruent with i386.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Acked-by: William Lee Irwin III <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
.. and adjust documentation to properly reflect options that are
x86-64 specific.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Consolidate the three 32-bit system call entry points so that they all
treat registers in similar ways.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove unused code and variables and do some codingstyle / whitespace
cleanups while at it.
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
xtime can be initialized including the cmos update from the generic
timekeeping code. Remove the arch specific implementation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the generic cmos update function in kernel/time/ntp.c
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current SMI detection logic in read_hpet_tsc() makes sure,
that when a SMI happens between the read of the HPET counter and
the read of the TSC, this wrong value is used for TSC calibration.
This is not the intention of the function. The comparison must ensure,
that we do _NOT_ use such a value.
Fix the check to use calibration values where delta of the two TSC reads
is smaller than a reasonable threshold.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is not fully softirq safe anyways.
Can't do a WARN_ON unfortunately because it could trigger in the
panic case.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With that an L3 cache is correctly reported in the cache information in /sys
With fixes from Andreas Herrmann and Dean Gaudet and Joachim Deguara
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This implements new vDSO for x86-64. The concept is similar
to the existing vDSOs on i386 and PPC. x86-64 has had static
vsyscalls before, but these are not flexible enough anymore.
A vDSO is a ELF shared library supplied by the kernel that is mapped into
user address space. The vDSO mapping is randomized for each process
for security reasons.
Doing this was needed for clock_gettime, because clock_gettime
always needs a syscall fallback and having one at a fixed
address would have made buffer overflow exploits too easy to write.
The vdso can be disabled with vdso=0
It currently includes a new gettimeofday implemention and optimized
clock_gettime(). The gettimeofday implementation is slightly faster
than the one in the old vsyscall. clock_gettime is significantly faster
than the syscall for CLOCK_MONOTONIC and CLOCK_REALTIME.
The new calls are generally faster than the old vsyscall.
Advantages over the old x86-64 vsyscalls:
- Extensible
- Randomized
- Cleaner
- Easier to virtualize (the old static address range previously causes
overhead e.g. for Xen because it has to create special page tables for it)
Weak points:
- glibc support still to be written
The VM interface is partly based on Ingo Molnar's i386 version.
Includes compile fix from Joachim Deguara
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In acpi_scan_nodes(), we immediately return -1 if acpi_numa <= 0, meaning
we haven't detected any underlying ACPI topology or we have explicitly
disabled its use from the command-line with numa=noacpi.
acpi_table_print_srat_entry() and acpi_table_parse_srat() are only
referenced within drivers/acpi/numa.c, so we can mark them as static and
remove their prototypes from the header file.
Likewise, pxm_to_node_map[] and node_to_pxm_map[] are only used within
drivers/acpi/numa.c, so we mark them as static and remove their externs
from the header file.
The automatic 'result' variable is unused in acpi_numa_init(), so it's
removed.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use LOCAL_DISTANCE and REMOTE_DISTANCE in x86_64 ACPI code
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linux 64bit only uses the IO-APIC ID as an internal cookie. In the future
there could be some cases where the IO-APIC IDs are not unique because
they share an 8 bit space with CPUs and if there are enough CPUs
it is difficult to get them that. But Linux needs the io apic ID
internally for its data structures. Assign unique IO APIC ids on
table parsing.
TBD do for 32bit too
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a bug introduced with the CLFLUSH changes: we must always flush pages
changed in cpa(), not just when they are reverted.
Reenable CLFLUSH usage with that now (it was temporarily disabled
for .22)
Add some BUG_ONs
Contains fixes from Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the new setup code, we generate a couple more files
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
[ .. and do the same for x86-64 - Alexey ]
Acked-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provides a way for NMI reported errors on x86 to notify the EDAC
subsystem pending ECC errors by writing to a software state variable.
Here's the reworked patch. I added an EDAC stub to the kernel so we can
have variables that are in the kernel even if EDAC is a module. I also
implemented the idea of using the chip driver to select error detection
mode via module parameter and eliminate the kernel compile option.
Please review/test. Thx!
Also, I only made changes to some of the chipset drivers since I am
unfamiliar with the other ones. We can add similar changes as we go.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Douglas Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the code for the "lg.ko" module, which allows lguest guests to
be launched.
[akpm@linux-foundation.org: update for futex-new-private-futexes]
[akpm@linux-foundation.org: build fix]
[jmorris@namei.org: lguest: use hrtimers]
[akpm@linux-foundation.org: x86_64 build fix]
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andi Kleen <ak@suse.de>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This changes the x86_64 linker script to use the asm-generic NOTES macro so
that ELF note sections with SHF_ALLOC set are linked into the kernel image
along with other read-only data. The PT_NOTE also points to their location.
This paves the way for putting useful build-time information into ELF notes
that can be found easily later in a kernel memory dump.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the arg+env limit of MAX_ARG_PAGES by copying the strings directly from
the old mm into the new mm.
We create the new mm before the binfmt code runs, and place the new stack at
the very top of the address space. Once the binfmt code runs and figures out
where the stack should be, we move it downwards.
It is a bit peculiar in that we have one task with two mm's, one of which is
inactive.
[a.p.zijlstra@chello.nl: limit stack size]
Signed-off-by: Ollie Wild <aaw@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <linux-arch@vger.kernel.org>
Cc: Hugh Dickins <hugh@veritas.com>
[bunk@stusta.de: unexport bprm_mm_init]
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently most of the per cpu data, which is accessed by different cpus,
has a ____cacheline_aligned_in_smp attribute. Move all this data to the
new per cpu shared data section: .data.percpu.shared_aligned.
This will seperate the percpu data which is referenced frequently by other
cpus from the local only percpu data.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
per cpu data section contains two types of data. One set which is
exclusively accessed by the local cpu and the other set which is per cpu,
but also shared by remote cpus. In the current kernel, these two sets are
not clearely separated out. This can potentially cause the same data
cacheline shared between the two sets of data, which will result in
unnecessary bouncing of the cacheline between cpus.
One way to fix the problem is to cacheline align the remotely accessed per
cpu data, both at the beginning and at the end. Because of the padding at
both ends, this will likely cause some memory wastage and also the
interface to achieve this is not clean.
This patch:
Moves the remotely accessed per cpu data (which is currently marked
as ____cacheline_aligned_in_smp) into a different section, where all the data
elements are cacheline aligned. And as such, this differentiates the local
only data and remotely accessed data cleanly.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move "debug during resume from s2ram" into the variable we already use
for real-mode flags to simplify code. It also closes nasty trap for
the user in acpi_sleep_setup; order of parameters actually mattered there,
acpi_sleep=s3_bios,s3_mode doing something different from
acpi_sleep=s3_mode,s3_bios.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a feature allowing the user to make the system beep during a resume from
suspend to RAM, on x86_64 and i386.
This is useful for the users with broken resume from RAM, so that they can
verify if the control reaches the kernel after a wake-up event.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch completes Linus's wish that the fault return codes be made into
bit flags, which I agree makes everything nicer. This requires requires
all handle_mm_fault callers to be modified (possibly the modifications
should go further and do things like fault accounting in handle_mm_fault --
however that would be for another patch).
[akpm@linux-foundation.org: fix alpha build]
[akpm@linux-foundation.org: fix s390 build]
[akpm@linux-foundation.org: fix sparc build]
[akpm@linux-foundation.org: fix sparc64 build]
[akpm@linux-foundation.org: fix ia64 build]
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Still apparently needs some ARM and PPC loving - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code for LDT segment selectors was not robust in the face of a bogus
selector set in %cs via ptrace before the single-step was done.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: extent macros cleanup
Fix compilation with EXT_DEBUG, also fix leXX_to_cpu conversions.
ext4: remove extra IS_RDONLY() check
ext4: Use is_power_of_2()
Use zero_user_page() in ext4 where possible
ext4: Remove 65000 subdirectory limit
ext4: Expand extra_inodes space per the s_{want,min}_extra_isize fields
ext4: Add nanosecond timestamps
jbd2: Move jbd2-debug file to debugfs
jbd2: Fix CONFIG_JBD_DEBUG ifdef to be CONFIG_JBD2_DEBUG
ext4: Set the journal JBD2_FEATURE_INCOMPAT_64BIT on large devices
ext4: Make extents code sanely handle on-disk corruption
ext4: copy i_flags to inode flags on write
ext4: Enable extents by default
Change on-disk format to support 2^15 uninitialized extents
write support for preallocated blocks
fallocate support in ext4
sys_fallocate() implementation on i386, x86_64 and powerpc
